Cisco WAN :: 2811 - 99% CPU High IP Input?
Dec 8, 2011
Our 2811 Edge router is having extremely high CPU problems. IP Input is consuming 70% of the process during business hours. Cisco express forwarding is enabled. It only shows 50% but its currently before business hours. Id say even 50% is still high.
CPU utilization for five seconds: 55%/16%; one minute: 70%; five minutes: 76%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
104 5310320 2813117 1887 36.92% 46.73% 51.43% 0 IP Input
The below interface is our public interface and is constantly over utilized with 100% Is there any configurations that can be done to correct this? Is there any more information that is needed?
IOS: (C2800NM-ADVSECURITYK9-M), Version 12.4(24)T4
Show IP Interface
FastEthernet0/0 is up, line protocol is up
Internet address is x.x.x.x
Broadcast address is x.x.x.x
Address determined by non-volatile memory
[code]....
View 3 Replies
ADVERTISEMENT
Oct 13, 2011
Today I've received reports of slow internet access/activity and have noticed myself that it seems a bit slow today. On the dashboard of our asa 5510 the "outside interface" traffic usage is running constantly high. It's at the top of the graph. How can I tell what is causing the spike in utilization. It usually runs at about 1500-2000 Kbps, and now it's up over 10,000.
View 6 Replies
View Related
Sep 23, 2012
Here is my conf:
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
View 6 Replies
View Related
Feb 4, 2013
my 3750-E Core Stack is connected to the Provider Router and is the DG for the internal LAN. I saw that the CPU is very high also in the night, but I found not the problem. I use an SVI to connect the provider due to HA reasons. I sniffered the network but saw no ecessive broadcaststorms. There was a PBR configured but I deleted it wihtout any success..
switch Version
15.0(1)SE1
10#sh proc cpu so
[Code]......
View 6 Replies
View Related
Feb 22, 2012
I have this output from show interfaces command for the fastethernet interface on a 2811 router.
find the causes of the crc and the ignored input errors on the interface?
The interface configuration is:
interface FastEthernet0/0description VLANS_CHILE
no ip address
[Code]....
View 6 Replies
View Related
Feb 6, 2012
We are experiencing with high CPU input due to ARP input between 20:30 and 22:30 every day At this time we have a lot of backup operations. When I look the netflow report, I can't see anything anormal.
We are changing our backup server's NIC card from 1gig to 10Gig. The backup operation's traffic is high (approx 2Gbps level) but 6509 has to be handle this size of traffic.
We are using two 6509E in VSS mode and our image version is s72033-adventerprisek9_wan-mz.122-33.SXJ.bin
20:00
show ip arp summary
--------------
2588 IP ARP entries, with 166 of them incomplete
[Code].....
View 16 Replies
View Related
Oct 1, 2011
We added Site02 for redundancy and DR. Also added new SAN and ESX hosts. The CPU on device Site01Server01 is not very happy when files are being transferred between the sites. Since the setup is the same at both sites, why is the problem only at site01?
Site02 is newer and we have two 3750X-24 with IOS 12.2(55)SE3 on ipservices, for site02server01; no problem.
Site01server01 is a stack of two 3750G-24PS with IOS 12.2(58)SE on ipservices.
[Code]....
View 5 Replies
View Related
Aug 13, 2011
I have 2 connections a single T1 for voip traffic only and a DSL line for data traffic.the dsl was migrated to a 2811 with out any issues now comes the time to move the T1 over.
on the T1 side I am able to ping the WAN router and the LAN router IP address but nothing behind it.
currently this is the only statment on the router:
ip route 0.0.0.0 0.0.0.0 Dialer1
as a quick a dirty to remove the above i tried:
no ip route 0.0.0.0 0.0.0.0 Dialer1
ip route 66.55.110.0 255.255.255.0 Dialer1
but the DSL side dropped. we have a 66.55.110.152/29
for the T1 i would use the following statement.. we have a 209.98.53.192/27
ip route 209.98.53.0 255.255.255.255 65.32.70.177
View 12 Replies
View Related
Sep 3, 2012
We have Cisco ME3400 switch, with configuration described below.
GE0/1 port is uplink:
interface GigabitEthernet0/1
description ***MATED-IUB_C&U-Plan***
port-type nni
switchport trunk allowed vlan 331,450,4085
switchport mode trunk
GEo/2 is configured as below:
interface GigabitEthernet0/2
description ***From NIB***
port-type nni
switchport access vlan 4085
[URL]
We have also tried Loopguard feature enabled on all ports: but after some period same problem is repeated.
version information is below:
Cisco IOS Software, ME340x Software (ME340x-METROIPACCESSK9-M), Version 12.2(25)SEG3, RELEASE SOFTWARE (fc2)
Copyright (c) 1986-2007 by Cisco Systems, Inc.
Compiled Wed 25-Jul-07 22:56 by amvarma
View 8 Replies
View Related
Feb 25, 2013
I have a connection that is loosing packets, my show interface output below summarises the interface where i believe the problem is occuring. My Hardware is 6509 running 12.2
View 1 Replies
View Related
Apr 29, 2013
I have a 2811 that is really hitting the CPU hard. Nothing shows on CPU processes. It has an IPsec VPN tunnel back to HQ which also has a 2811 that terminates the VPN. The HQ has 2-3 IPsec tunnels to other remote sites. The CPU at the HQ avg 50% utilization during business hrs, peaks at about 80%. The remote one is very high 95% peaks, avg 80%-95% during business hours with bandwidth utilization of only 10-20Mbps. I read somewhere that its possible that fragmentation could be causing this. My question is, if I set the MTU to 1450 on the remote, I am guessing I will need to do all the other routers as well, the HQ and other remote sites? Siince they use the same outside interface to my HQ, is that correct?
View 3 Replies
View Related
Jun 23, 2011
We have Cisco 2811 router and facing high CPU utilisation as 70%/67%;,IOS Runing :c2800nm-advsecurityk9-mz.124-3f.bin.
View 4 Replies
View Related
Sep 24, 2012
I have a router 2811 and shows high CPU utilization 90%, it is observed that this happens when the traffic increases, the router also has firewall enabled services, QoS, DHCP, ACLs, NAT. As my router could not determine what is appropriate for my use, and how it could choose a router that meets my needs.
View 6 Replies
View Related
May 9, 2011
there is no logging in the access-list (there is only one inbound access list).Using QoS or not, doesn't seem to make a differenceAll route-caching features are ON. (CEF, Flow, Policy, Fast)Yet the minimum CPU utilisation I have seen is 25%/25%... On average it's 40% during the day, but once traffic picks up to around 6000 packets per second, the router is gone...I have a 50/50 Mbps connection, but I can use only 6 for VoIP ?
Show interfaces:
GigabitEthernet0/0 is up, line protocol is up
Hardware is MV96340 Ethernet, address is 0014.1c26.7c30 (bia 0014.1c26.7c30)
Description: $ETH-LAN$$FW_INSIDE$
MTU 1500 bytes, BW 100000 Kbit, DLY 100 usec,
reliability 255/255, txload 6/255, rxload 7/255
[code]...
View 15 Replies
View Related
Oct 24, 2012
We are having issues with our Cisco 2811 when there a lot of traffic on the device. Usually the router is down around 5%-10%. Total traffic might be around 2.0 MB. This is a router we are using at a remote campus. We do HD video conferencing every friday. We have a 10 MB internet connection that has our VPN connection to the main campus on it. While doing these VTC, the totall traffic is about 6 MB. The CPU Utilization then rises to approx 75% cause call issues and loss of sound. With another test with no one using the connection for anything else the utilization went up to 35%. The router has 128 MB Ram in it. Does the router need more RAM or do we need a larger internet pipe.
View 7 Replies
View Related
Sep 24, 2012
I have a 2811 Router that is experiencing high CPU utilization. I have already issued the "show cpu proc" command, and everything seems to be fine (it's not a process issue) . According to our traffic graphs, we've seen that CPU is related to high link utilization, since we have 2 Fast Ethernet interfaces (Internet 4 MB and MPLS 6 MB), and when those interfaces have to deal with a lot of traffic at some hours, the CPU Load increases in the Router.
I found an article where they say that 2811 ISR Routers can deal with up to 61,44 Mbps (120.000 pps), but our router is far away from reaching that limit.It usually manages up to 16 MBPS. This router manages some services such as NAT traslation, ACLs, voice traslation profiles, policy routing (QoS), firewall and DHCP.
What can be happening to the router?.. Is it normal that when it has to process a lot of traffic, its cpu must increase up to 95%, even if it is handling just 16 MB compared to the theorical 61 MB? Is there any command or tool that I could use to troubleshoot this issue? Is there any limit in terms of WAN traffic that it could handle? How much influence do those services have over CPU Utilization?
Given these incidents, which router series could suit better in my network to avoid high CPU issues?
View 11 Replies
View Related
Aug 10, 2011
I am facing a problem on a 2811 router. The CPU is remaining around 60% and the router throughput is reaching at most 18 MB while according to the data sheet the 2811 maximum throughput is 61MB. I have checked the output interpreter in order to try and figure out the cause of the high CPU and to determine if it is affecting throughput but there are not processes consuming more than 10%. I have attached the show tech-support and the show process cpu history outputs.
View 11 Replies
View Related
Apr 24, 2011
2811 router
Cisco IOS Software, 2800 Software (C2800NM-ADVENTERPRISEK9_IVS_LI-M), Version 12.4(24)T4, RELEASE SOFTWARE (fc2)
CPU utilization for five seconds: 82%/73%; one minute: 74%; five minutes: 77% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 116 222084 57773 3844 1.83% 1.69% 1.66% 0 IP Input 183 85148 309479 275 1.03%
[Code].....
View 9 Replies
View Related
Apr 4, 2012
I have cisco 2811 at branch and 3845 at Head office. Two link with 256 kbps bandwidthe each. I did as follows: [code]
When link 1 down, traffic change to Tunnel 2. its OK.I want when link1 flaxuate or latency high (more than 60 ms) traffice change to tunnel 2. If link 2 goes high latency automatically change to tunnel 1.
View 1 Replies
View Related
Feb 23, 2013
we have 2811 router with multiple servers connected to it's lan from which there are monitoring servers in between , the router suffers always from high cpu utilization
configuration has alot of ACLs & NAT & IPSEC Tunnel with wan bandwidth 20 M? Is there any method to reduce the high CPU utilization shown below !!
CPU utilization for five seconds: 90%/80%; one minute: 93%; five minutes: 90%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
104 737029848 427864243 1722 5.45% 5.65% 5.65% 0 IP Input
253 63392216 11081854 5720 1.04% 1.15% 1.12% 0 IP NAT Ager
260 82602372 137425723 601 0.64% 0.64% 0.66% 0 PDU DISPATCHER
[code]....
View 4 Replies
View Related
Nov 26, 2012
We installed a solution with 2 Cisco 2801, BGP multihomed failover.
1) The router which is currently getting all the traffic gets to 55% to 60% of CPU usage when handling 40 SIP/RTP streams . This equals 10Mbit up/10Mbit down and it showed around 5800 packets TX and around 5800 packets RX, with a majority of them CEF switched. As those figures are way less than the performance figures published by Cisco, we wonder if we made any mistake in setting up our router, or if we can do something to improve the router setup.
2) Does it have an impact on router performance if we increase/decrease RTP packet size, thus increasing or decreasing the pps relative to the consumed bandwidth?
3) If it is not possible to improve router configuration, we also wonder about possible replacement units for those routers. Would a 2901 do a good job? By how much would it rise the capacity? What other models would you recommend if we plan to rise the number of concurrent calls by a factor of 4 or even 8 times of what we have now (so up to 48000 pps and 80Mbit).
Here is what we tried:
- ip route-cache same-interface does not seem to improve anything
- ip flow ingress on or off makes no difference
- disabling the inbound ACL on fa0/0 seems to reduce load by 10%, although I don't understand why - a very high percentage is CPU interrupts, and ACLs are process switched, or not?
- we tried following the Cisco guide for high CPU due to high interrupts, with no success
Here are some usage statistics:
The graphs that we plot via SNMP show a propotional growth/increase of CPU and bandwidth (and thus pps) At the highest loads, we had a bit more than 55% CPU utilization with more than 50% interrupt CPU.
CPU utilization for five seconds: 36%/30%; one minute: 30%; five minutes: 30%
PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process
127 13140 954 13773 2.00% 0.29% 0.07% 194 SSH Process
[Code].....
View 8 Replies
View Related
Nov 12, 2011
what's the difference between High-power and High-gain wireless USB adapters.
View 5 Replies
View Related
May 28, 2013
By default there 2 input queues. 2nd is priority queue and has 10% of link assigned. Weights for two queues are 4 and 4. For example we have 1Mbps link. ANd we also have saturated link with voice and other traffic. Will voice get 550k bandwidth? As I undestood 100k is assigned to voice strictly. Remaining 900k is evenly divided by two queues according to 4 and for ratio.
View 7 Replies
View Related
Oct 20, 2011
Do I need to plug in AP 1262 into a PoE switch or external power adapter before can power on? How about LAP 1262? Do I need PoE switch as well?
View 4 Replies
View Related
Nov 4, 2011
I use an 1841 router as an internet facing firewall with a 10MB MetroE connection. Lately users started reporting slow internet download speeds and web pages timing out. Bandwidth reports do not show the link as being saturated so I looked at the interfaces on the 1841. The interface connected to the provider shows OK as far as errors but the LAN side of the router shows steadily increasing input errors. It doesn't show any other errors, no CRC, frame, runts, giants or overruns, just generic input errors. What type of errors are those? Nothing is being logged on the console.
I moved the connection to another switch ports and the errors continue. I switched it down to 10MB and also changed the switch and the errors slow down but don't stop. Interestingly, the switch side never shows any errors. What can I do here? I guess it can be a bad interface but that is such a rare thing that I am hesitant to replace the router.
View 11 Replies
View Related
Feb 7, 2011
I have this topology in part of my networ:k
Cisco7200---Cisco6500---Cisco3560---LAN1
|
Cisco3560
|
LAN2
All devices are interconected via optical 1Gb/s links. There is no QoS implemented on any device and all VLANs are allowed on all interfaces.
Also all links are trunks (with many VLANs)
In LAN1 there was a layer 2 broadcast-storm and 4000packets/s was comming to rest of the network (in one particular VLAN).
1) 7200 with G1 should be able to handle traffic up to 500Mb/s, but a lot of users experienced drops on traffic via 7200.
(CPU load was around 10%).
2) Why do I have input drops on 7200 on link toward 6500 if CPU was normal. Broadcast comming to this interfaces were cca 4kpps. But since it's destination is not on router these packets should be rejected on interface controller. Is that right? (7200 doesn't even has dot1q subinterface in that VLAN but since 6500 allow all VLANs on its trunk these packets reach 7200)
3) Why do I have output drops on Cisco 6500 (it is here as layer 2 device only)? It is max 160Mb/s in output direction. It has WS6724 card with DFC (there is no oversubscription).. Shouln't 6500 send traffic as fast as interface allows (up to 1Gb/s). Am I righ't?
4) After all how coul'd 6500 now if 7200 can't handle these traffic?Output drops should be only seen if QoS is enabled (i.e. shaping), or if there is oversubscription on the linecard?
View 4 Replies
View Related
Feb 2, 2011
why my input parameter are gone in the TAGGED website ?
View 1 Replies
View Related
Mar 25, 2012
Running vista. When I pull up my list of possible wireless signals to try and connect.
I normally get asked to input a security key. NOW the screen will simply close after i press the enter key. Right clicking and trying to connect also am having the same issue. MY wireless signal for MY comcast account it connects perfectly.
View 1 Replies
View Related
Aug 3, 2011
I bought a DVI D to hdmi connector so i can watch movies from my computer on my hdtv but whenever i try to switch to DVI on my HP w1907 my monitor says no input signal.
View 1 Replies
View Related
Oct 22, 2011
In university I have one ethernet socket in my room which I have connected to an ethernet port on my wireless router. I have also connected all my other ethernet devices to the router so I don't have to keep unplugging them and replacing the ethernet cable in the wall socket. I can connect to the internet through the router but it's only allowing one device to be connected at once and the router is saying "no connection" even though I can connect through it. does this mean it's working as a switch at the moment, right? Would it be possible to make it work as a router so all my devices can work simultaneously and get the wifi to work?
View 5 Replies
View Related
Feb 5, 2013
I have connected the input cable of router to LAN port instead of INTERNET port and i got internet (some time only). due to that I caught by the authority and they are saying that change of port was the problem. Already there was a problem to our server (might be hardware problem).
View 2 Replies
View Related
Mar 16, 2011
I've just got my hands on a Cisco PIX 515. I mainly brought it too learn and play with, i done some Cisco stuff in the past but not much.
I just need too get this up and running with a IP Address on ethernet1 (192.168.1.254) but when I run the command "name if ethernet1 inside security100" in enable mode all I keep getting is ERROR % Invalid input detected at '' maker
View 61 Replies
View Related
Mar 22, 2012
We have 7206 VXR running NPE-G1, we are looking for the GigE cards for 7200 which supports upto line rate and came across Cisco 7200 Series Input/Output Controllers The datasheet for the same doesnt say anything about line rates.
View 3 Replies
View Related
