TP-Link 3G/3.75G Router :: TL-MR3420 / Setup Info For Service Provider?

Mar 15, 2013

Region : Austria
Model : TL-MR3420
Hardware Version : V1
Firmware Version :
ISP : orange.at

When I first installed the router I used the built-in provider settings for "ONE" which used to be the name of the provider before it was taken over by orange.at. It seemed to work fine but I experienced some funny server errors with certain web services. I contacted orange.at about this and they told me to adjust the provider settings in the router as follows:

Dial number: *99#
APN: fullspeed

The reason for the problems was that they use different proxy servers for their services and applications. Now it works fine (so far).

View 1 Replies


ADVERTISEMENT

Linksys Wireless Router :: WRT54G V7 - Cannot Specify Service Provider

Mar 14, 2007

WRT54G v7 - cannot specify service provider

View 9 Replies View Related

Linksys Wireless Router :: E1000 Changing Internet Service Provider

Sep 3, 2010

If I have a wireless network set up with the Linksys E1000 using one internet provider and then change the internet provider service to someone else, do I have to reset up the network or is it simply a matter of connecting the new internet service to the router?

View 3 Replies View Related

TP-Link ADSL2+ Wireless :: Setup Info To Connect TD-W8968 To CenturyLink?

Feb 21, 2013

Model : TD-W8968
Hardware Version : V1
Firmware Version : ?
ISP : CenturyLink

I need the setup info to connect the TD-W8968 to CenturyLink.

View 1 Replies View Related

Cisco :: Service Provider Blocking VPN?

Feb 5, 2013

"The service provider in your current location is restricting access to the InternetYou need to log on with the service provider before you can establish a VPN session. You can try this by visiting any website with your browser."We are using an Internal IP....and the external, same resultI am the IT Admin and this was working last week till I upgraded to the newer anyconnect. Internet is just fine....I am at a loss.

View 7 Replies View Related

Computer Looking For Wrong Service Provider

Feb 25, 2012

My folks have Time Warner (Roadrunner) Internet service. They power-down their Dell every night. When they shut down last night they had no problems and were running Time Warner (Roadrunner). When they booted the computer this morning the computer is trying to connect to Adelphia.

They changed nothing. The wiring to the computer was not compromised in any way.

Time Warner tried to "ping" their modem and could not "see" the modem. They think it is a line problem - but the fact that the computer is looking to connect to an alternate service provider makes me think that it is possibly a problem with a setting in the computer.

View 1 Replies View Related

Switching Internet Service Provider On ISA

Sep 10, 2012

I have Windows 2008 server running isa server with dedicated ip (which I take from my Internet Service Provider ISP) running my website, if my internet connection is down my website is not accessible from outside world.How can I switch to another ISP using same dedicated ip address when my ISP connection is down?

View 1 Replies View Related

WNDR3400v2 - Add A Different Dynamic DNS Service Provider?

Jul 22, 2012

I have DNS setup through No-IP.com. How do I add this service provider to my WNDR3400v2 router? It only has DynDNS.org listed and I can't create a free account there.

View 1 Replies View Related

TZ-210 - Configuring Static IPs From Two Different Service Provider

Mar 27, 2012

how to separate two different static Ip address provided by different service provider in Sonic wall TZ-210

View 6 Replies View Related

Protocols / Routing :: Who Is Your Internet Service Provider

Sep 4, 2012

Is this a wired or wireless connection issue? Both Who is your Internet Service Provider (ISP)? Comcast..What type of Broadband connection are you using? Cable..What is the exact Make and Model of your Modem, Router or Modem/Router Combo - (Main)Netgear WNR3700v2 / WNR2000v3(secondary) My current setup is the 3700 router is taking the internet from the modem cat5e and spewing the wireless. I would like to have the secondary router use the wireless from router 1 as the internet source and push the internet out of the 4 hardline ports so I can plug my upstairs xbox 360 into the router via cat5e. I'm just kinda new to this and still learning so I'm not sure how to configure the router to do this. I can get into the settings of the router just fine but finding the right settings to tweak is a little difficult.

View 3 Replies View Related

Cisco :: 3600 Connection With Service Provider

Jul 9, 2012

I have currently a Cisco 3600 router, it has three interfaces (all ethernet interfaces only).We being a client, our requirement is, we want two links one being the primary and one secondary for the fail over.My ISP has done certain configurations, but I am so puzzled what really has been done. I asked with them and they told that they have provided us one public IP 202.166.217.248 via Fibre--> Media Converter-->Ethernet 0/0.At the same time, they have given us a pool of addresses of the network 202.166.216.48/29 through the interface Ethernet 2/1.And we have used all the available public IPs in the server farm.They have told that, for the failover purpose via wireless, they have even used an IP address 202.166.213.114/25.
 
Now, where my confusion lies is, cant they provide the pool address via fibre? What is the significance of the ip that has been provided via fibre? What actually is its purpose? Isn't it consuming an extra interface ?Cant we have both the primary and secondary link excluding that one additional process?Or, am not understanding the real working mechanism how ISP distribute the internet?

View 1 Replies View Related

Cisco WAN :: 1841 Can't Able To Use Different Service Provider At Same Time

Mar 4, 2012

I have cisco 1841 router in my office.In that router we configured MPLS bgp with two different service provider. [code] We can't able to use the different service provider at the sametime.Cisco 1841 is support two different AS ???

View 12 Replies View Related

Broadband :: Internet Service Provider Doesn't Have Wifi

Nov 4, 2012

I have a wired broadband connection with a modem. My internet service provider does not have Wi-Fi. Can I convert it myself into wi-fi by connecting it to a router. If possible how?

View 6 Replies View Related

Couldn't Establish Connection With Server Of Service Provider

Aug 28, 2012

My modem with single network connectivity (Type I) works fine. I tried to replace with Type II modem (with wifi- and 4 or more ports) for connectivity. I could not establish connection with the server of the service provider. I tried to replace with a different type of typeII modem. Still the same. What could be the reason?I connected the same in a different workplace to a different PC.

View 1 Replies View Related

Cisco VPN :: Configure L2L VPN Tunnel To Service Provider Using ASA 5505

Jun 3, 2012

I am trying to confgure a L2L VPN tunnel to a service provider using an ASA 5505.My problem is that the service provider will not accept traffic from a LAN subnet, they will only accept traffice from a public IP.We have a small public subnet of x.x.x.50/255.255.255.248, our public IP (outside interface IP on the ASA 5505) is x.x.x.50 and the service provider wants to see traffic coming from us on x.x.x.51How can I NAT our LAN subnet (10.0.0.0/24) to one public IP (x.x.x.51)?

View 14 Replies View Related

Cisco :: Configure Load Balancing In MPLS Between Two Different Service Provider?

Dec 19, 2012

How to configure load balancing in MPLS between two different service provider.

View 4 Replies View Related

Cisco Switching/Routing :: 2600 DHCP From Service Provider Not Working

Feb 7, 2013

So I have  a 2600 that I have configured three sub interfaces on. FA0.0.1 is set for DHCP and supports VLAN 1. FA 0/0.2 for Voice, FA 0/0.3 for Data. I have this router interface plugged into FA 0/24 on my 3550 and the 3550 is configured as a dot1Q trunk (I have attached configs for RTR and SW).I have most ports configured as access VLAN 1 which is where i have my ISP connection plugged FA0/1 on the 3550. When I connect the service provider link FA0/0.1 never picks up an address. If I take my internal DHCP server and connect it to FA0/1 of the 3550 it snags an address almost immediately.In my mind this validates that my config is fine. I also took the same cable from the service provider cable modem and connected it to my laptop and the laptop is pulling DHCP.

View 4 Replies View Related

Cisco WAN :: ME3400 / Injecting Two Default Routes Via Ospf Into Service Provider MPLS?

Jan 24, 2011

We have multiple sites that are linked via MPLS (L3) circuits. We have good size circuits for Internet at two main sites (HQ and QC) and smaller sites come to HQ site to go to internet. We are running ospf (Cisco L3 switches) with service provider (ME3400) at these two main sites and service provider then redistributes routes back into MPLS via BGP and then smaller sites ME3400 learn these routes. i am injecting default routes from HQ and QC, but Telco is only redistributing default from HQ. So large pipe Internet at QC is not being used effeciently. Also if MPLS at HQ fails, then we are told, we need to call Telco and they will make change in their network to now start distributing default from QC.it was my understanding that telco can use BGP communities and advertize one default as prefered and second with higher cost, so that failover can occur automatically. And that they can also set up so that west cost sites use HQ and east cost sites can use QC for going to internet, but they say it is not possible.it the least, can I do something like this at my end for failover for internet, in case MPLS at HQ goes down (soon we will be setting up a point to point VPN tunnel between HQ and QC so that MPLS failure at HQ will trigger advertisement of HQ routes over tunnel via QC into MPLS, so other sites can then come to HQ thru QC over this tunnel. At QC Cisco router (to detect loss of default route from HQ and then start advertizing default from QC) 
 
router ospf 1
 default-information originate always route-map From_HQ
 exit
 ip access-list standard From_HQ

[code]....

View 3 Replies View Related

Cisco Switching/Routing :: 7600 Service Provider Has 1000-Full With Auto-negotiate

Jan 21, 2013

I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.

View 2 Replies View Related

D-Link DIR-615 :: Setup IPv6 In IPv4 Tunnel With Tunnerbroker Service

Mar 24, 2013

Recently I wanted to setup IPv6 for my home network. I signed up for tunnelbroker.net service and was provided with IPs. Then I configured the IP address in my DIR-615. But It's not working..

Screenshot of IPv6 config (router) : Screenshot of my Win 8 network Config : I also tested at [URL] but failed...

View 3 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 - Cannot Login To 192.168.1.1

Dec 4, 2012

Region : Finland
Model : TL-MR3420
Hardware Version : V1
Firmware Version : cannot login to check it out
ISP :

Cannot login in to 192.168.1.1 - I have even reset the router - yesterday it worked well - today not - i ahve not done any update.

View 7 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 Disconnects When Uploading

Apr 13, 2013

Region : Australia
Model : TL-MR3420
Hardware Version : V1
Firmware Version : TL-MR3420_V1_121123
ISP : BIGPOND

My problem is whenever I upload anything, my modem disconnects. My USB Dongle is a Telstra Ultimate 3G Sierra Wireless AirCard 312U. The problem is not present whenever I connect the dongle directly into the USB port on my LapTop.

View 1 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 - How To Save PIN Code

Feb 5, 2013

Region : Others
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 3.13.27 Build 120905 Rel.73281n

I have successfully connected to my ISP with the 3G USB dongle.But it seems like the PIN code is not saved. I have to enter it after a reboot of the router.

View 2 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 Does Not Recognizes ZTE MF190

Nov 26, 2012

Region : Colombia
Model : TL-MR3420
Hardware Version : V1
Firmware Version : TL-MR3420_V1_120523
ISP : CLARO

Does not find Modem. Just purchased it in Cartagena, Colombia to use with ISP Claro.Using Modem ZTE model MF 190

View 10 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 Does Not Connect With 3G ZTE MF190

Jan 9, 2013

Region : Sweden
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.13.1 Build 121123 Rel.57630n
ISP : Telenor

I have TP-LINK 3G/3.75G Wireless N Router Model # TL-MR3420 which is compatible with Telenor 3G USB ZTE MF190. With quick setup I have successfully configured the router, but the router does not connect with 3G ZTE MF190. I even called the Telenor helpline, they say that, they've no support for TP-LINK.

View 2 Replies View Related

TP-Link 3G/3.75G Router :: MF636 Not Working With TL MR3420

Apr 26, 2013

Region : Israel
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 3.13.31 Build 130128 Rel.56595n (Beta)
ISP : Israel . Cellcom 3g

When I plug the USB Modem to the router its show

Unknown USB Modem

this is the 3 usb modem I tried after I had bought the TL MR3420

View 1 Replies View Related

TP-Link 3G/3.75G Router :: Does ZTE 669 Turbo Work With MR3420

Jan 15, 2013

Region : New Zealand
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP : Telecom New Zealand

getting the MR3420 but will be using a ZTE 669 Turbo stick as the modem ISP Telecom New Zealand.I did notice that they seem to be supporting the ZTE 668+ which I'm guessing is a vary similar model.

View 3 Replies View Related

TP-Link 3G/3.75G Router :: Add External Battery In TL-MR3420?

Apr 24, 2013

Region : India
Model : TL-MR3420
Hardware Version : V2
Firmware Version : 3.13.27 Build 121206 Rel.60215n
ISP : Airtel India

i Want To Add External Battery In My TL-MR3420 .. Is It Possible . Any One Try It Or Not . I Have Always Power Problem In My Home That's Why i Need Battery For My TL-MR3420... Any One Guide Me .. Any Hardware Diagram For It .. i'm Android Dev And hardware Eng .. If U Provide Me Hardware Diagram Or Any Other Info i Will Add External Battery In It ...

View 5 Replies View Related

TP-Link 3G/3.75G Router :: 5v USB - DC Power Specifications MR3420 V2?

Feb 11, 2013

[COLOR=#000000]Region : Australia
Model : TL-MR3420
Hardware Version : V2

rated DC power specifications of the usb port on the MR series? Is it the same for all TPLINK routers?ie 5v @ x amps?

View 5 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 - Cannot Connect To Internet

Apr 10, 2013

Region : Sweden
Model : TL-MR3420
Hardware Version : V2
Firmware Version :
ISP :

I'm trying to replace my old router with the TL-MR3420 but I cannot reach Internet.

I get "Internet" directly by a Cable into my apartment. This Cable is connected to the WAN input. Then I connect my computer to one of the LAN ports. (The Cable Connections are done exactly as on my previous router.)

The setup on my PC (running Windows 8) is as described in the manual (IP address automatic and DNS server automatic).

Internet doesn't work and I cannot reach the router from the browser using 192.168.1.1.

I'm not using any 3G and of course I have restarted the router (and PC) a couple of times. I thought I could just replace my old router with the new one... but NOT.

View 1 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 - Remote Administration Over 3G?

Apr 22, 2013

Region : Australia
Model : TL-MR3420
Hardware Version : Not Clear
Firmware Version :
ISP : Telstra

Is remote administration over 3G connection possible? The telstra public IP is not pingable. (from externally) Goes no where when I put the public IP into a browser. (from externally) Any settings changes to enable this?

View 1 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 - Compatible With ADSL2

Jan 16, 2013

Region : NewZealand
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 1.2
ISP : Now.

Is the TL-MR3420 (previous model/shape) compatible with ADSL2+? I can't find clear indication that it is or isn't

View 1 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 Bad Wireless Connection

Jan 13, 2013

Region : Malaysia
Model : TL-MR3420
Hardware Version : V1
Firmware Version : 3.12.21 Build 120523 Rel.37880n

Just wonder if anyone using the same model of router and having bad connection with wireless? Its OK with the pc LAN (physical cable) connection but intermittent lost signal, request timeout when connect from notebook or iphone/ipad via wireless whether with DHCP or fixed internal IP.

I am having this issue since day 1, then upgrade the firmware by myself... Still no good. I keep the device into store send to warranty claim. After 2-3 months only get back the device, firmware being updated to above.. It seems to be OK for 1st week( i think) ... but now lost signal again.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved