WNDR3400v2 - Add A Different Dynamic DNS Service Provider?

Jul 22, 2012

I have DNS setup through No-IP.com. How do I add this service provider to my WNDR3400v2 router? It only has DynDNS.org listed and I can't create a free account there.

View 1 Replies


ADVERTISEMENT

Free Dynamic DNS Provider?

Dec 17, 2012

What's the best free dynamic DNS provider?

I found a ton of them on the internet but I'm not sure which ones are safe.I'm trying to use my home NAS as an ftp server that can be accessed remotely.

View 3 Replies View Related

Cisco Switching/Routing :: 2911 - Dynamic IP From Provider

Feb 19, 2013

connected DSL directly to 2900 series router , but as DSL public IP is not static (dynamic)  its difficult to access Router when out of home,  any other means to access router without static IP

View 2 Replies View Related

Cisco :: Service Provider Blocking VPN?

Feb 5, 2013

"The service provider in your current location is restricting access to the InternetYou need to log on with the service provider before you can establish a VPN session. You can try this by visiting any website with your browser."We are using an Internal IP....and the external, same resultI am the IT Admin and this was working last week till I upgraded to the newer anyconnect. Internet is just fine....I am at a loss.

View 7 Replies View Related

Computer Looking For Wrong Service Provider

Feb 25, 2012

My folks have Time Warner (Roadrunner) Internet service. They power-down their Dell every night. When they shut down last night they had no problems and were running Time Warner (Roadrunner). When they booted the computer this morning the computer is trying to connect to Adelphia.

They changed nothing. The wiring to the computer was not compromised in any way.

Time Warner tried to "ping" their modem and could not "see" the modem. They think it is a line problem - but the fact that the computer is looking to connect to an alternate service provider makes me think that it is possibly a problem with a setting in the computer.

View 1 Replies View Related

Switching Internet Service Provider On ISA

Sep 10, 2012

I have Windows 2008 server running isa server with dedicated ip (which I take from my Internet Service Provider ISP) running my website, if my internet connection is down my website is not accessible from outside world.How can I switch to another ISP using same dedicated ip address when my ISP connection is down?

View 1 Replies View Related

TZ-210 - Configuring Static IPs From Two Different Service Provider

Mar 27, 2012

how to separate two different static Ip address provided by different service provider in Sonic wall TZ-210

View 6 Replies View Related

Protocols / Routing :: Who Is Your Internet Service Provider

Sep 4, 2012

Is this a wired or wireless connection issue? Both Who is your Internet Service Provider (ISP)? Comcast..What type of Broadband connection are you using? Cable..What is the exact Make and Model of your Modem, Router or Modem/Router Combo - (Main)Netgear WNR3700v2 / WNR2000v3(secondary) My current setup is the 3700 router is taking the internet from the modem cat5e and spewing the wireless. I would like to have the secondary router use the wireless from router 1 as the internet source and push the internet out of the 4 hardline ports so I can plug my upstairs xbox 360 into the router via cat5e. I'm just kinda new to this and still learning so I'm not sure how to configure the router to do this. I can get into the settings of the router just fine but finding the right settings to tweak is a little difficult.

View 3 Replies View Related

Cisco :: 3600 Connection With Service Provider

Jul 9, 2012

I have currently a Cisco 3600 router, it has three interfaces (all ethernet interfaces only).We being a client, our requirement is, we want two links one being the primary and one secondary for the fail over.My ISP has done certain configurations, but I am so puzzled what really has been done. I asked with them and they told that they have provided us one public IP 202.166.217.248 via Fibre--> Media Converter-->Ethernet 0/0.At the same time, they have given us a pool of addresses of the network 202.166.216.48/29 through the interface Ethernet 2/1.And we have used all the available public IPs in the server farm.They have told that, for the failover purpose via wireless, they have even used an IP address 202.166.213.114/25.
 
Now, where my confusion lies is, cant they provide the pool address via fibre? What is the significance of the ip that has been provided via fibre? What actually is its purpose? Isn't it consuming an extra interface ?Cant we have both the primary and secondary link excluding that one additional process?Or, am not understanding the real working mechanism how ISP distribute the internet?

View 1 Replies View Related

Cisco WAN :: 1841 Can't Able To Use Different Service Provider At Same Time

Mar 4, 2012

I have cisco 1841 router in my office.In that router we configured MPLS bgp with two different service provider. [code] We can't able to use the different service provider at the sametime.Cisco 1841 is support two different AS ???

View 12 Replies View Related

Broadband :: Internet Service Provider Doesn't Have Wifi

Nov 4, 2012

I have a wired broadband connection with a modem. My internet service provider does not have Wi-Fi. Can I convert it myself into wi-fi by connecting it to a router. If possible how?

View 6 Replies View Related

Couldn't Establish Connection With Server Of Service Provider

Aug 28, 2012

My modem with single network connectivity (Type I) works fine. I tried to replace with Type II modem (with wifi- and 4 or more ports) for connectivity. I could not establish connection with the server of the service provider. I tried to replace with a different type of typeII modem. Still the same. What could be the reason?I connected the same in a different workplace to a different PC.

View 1 Replies View Related

Linksys Wireless Router :: WRT54G V7 - Cannot Specify Service Provider

Mar 14, 2007

WRT54G v7 - cannot specify service provider

View 9 Replies View Related

Cisco VPN :: Configure L2L VPN Tunnel To Service Provider Using ASA 5505

Jun 3, 2012

I am trying to confgure a L2L VPN tunnel to a service provider using an ASA 5505.My problem is that the service provider will not accept traffic from a LAN subnet, they will only accept traffice from a public IP.We have a small public subnet of x.x.x.50/255.255.255.248, our public IP (outside interface IP on the ASA 5505) is x.x.x.50 and the service provider wants to see traffic coming from us on x.x.x.51How can I NAT our LAN subnet (10.0.0.0/24) to one public IP (x.x.x.51)?

View 14 Replies View Related

Cisco :: Configure Load Balancing In MPLS Between Two Different Service Provider?

Dec 19, 2012

How to configure load balancing in MPLS between two different service provider.

View 4 Replies View Related

TP-Link 3G/3.75G Router :: TL-MR3420 / Setup Info For Service Provider?

Mar 15, 2013

Region : Austria
Model : TL-MR3420
Hardware Version : V1
Firmware Version :
ISP : orange.at

When I first installed the router I used the built-in provider settings for "ONE" which used to be the name of the provider before it was taken over by orange.at. It seemed to work fine but I experienced some funny server errors with certain web services. I contacted orange.at about this and they told me to adjust the provider settings in the router as follows:

Dial number: *99#
APN: fullspeed

The reason for the problems was that they use different proxy servers for their services and applications. Now it works fine (so far).

View 1 Replies View Related

Linksys Wireless Router :: E1000 Changing Internet Service Provider

Sep 3, 2010

If I have a wireless network set up with the Linksys E1000 using one internet provider and then change the internet provider service to someone else, do I have to reset up the network or is it simply a matter of connecting the new internet service to the router?

View 3 Replies View Related

Cisco Switching/Routing :: 2600 DHCP From Service Provider Not Working

Feb 7, 2013

So I have  a 2600 that I have configured three sub interfaces on. FA0.0.1 is set for DHCP and supports VLAN 1. FA 0/0.2 for Voice, FA 0/0.3 for Data. I have this router interface plugged into FA 0/24 on my 3550 and the 3550 is configured as a dot1Q trunk (I have attached configs for RTR and SW).I have most ports configured as access VLAN 1 which is where i have my ISP connection plugged FA0/1 on the 3550. When I connect the service provider link FA0/0.1 never picks up an address. If I take my internal DHCP server and connect it to FA0/1 of the 3550 it snags an address almost immediately.In my mind this validates that my config is fine. I also took the same cable from the service provider cable modem and connected it to my laptop and the laptop is pulling DHCP.

View 4 Replies View Related

Cisco WAN :: ME3400 / Injecting Two Default Routes Via Ospf Into Service Provider MPLS?

Jan 24, 2011

We have multiple sites that are linked via MPLS (L3) circuits. We have good size circuits for Internet at two main sites (HQ and QC) and smaller sites come to HQ site to go to internet. We are running ospf (Cisco L3 switches) with service provider (ME3400) at these two main sites and service provider then redistributes routes back into MPLS via BGP and then smaller sites ME3400 learn these routes. i am injecting default routes from HQ and QC, but Telco is only redistributing default from HQ. So large pipe Internet at QC is not being used effeciently. Also if MPLS at HQ fails, then we are told, we need to call Telco and they will make change in their network to now start distributing default from QC.it was my understanding that telco can use BGP communities and advertize one default as prefered and second with higher cost, so that failover can occur automatically. And that they can also set up so that west cost sites use HQ and east cost sites can use QC for going to internet, but they say it is not possible.it the least, can I do something like this at my end for failover for internet, in case MPLS at HQ goes down (soon we will be setting up a point to point VPN tunnel between HQ and QC so that MPLS failure at HQ will trigger advertisement of HQ routes over tunnel via QC into MPLS, so other sites can then come to HQ thru QC over this tunnel. At QC Cisco router (to detect loss of default route from HQ and then start advertizing default from QC) 
 
router ospf 1
 default-information originate always route-map From_HQ
 exit
 ip access-list standard From_HQ

[code]....

View 3 Replies View Related

Cisco Switching/Routing :: 7600 Service Provider Has 1000-Full With Auto-negotiate

Jan 21, 2013

I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.

View 2 Replies View Related

Linksys Wireless Router :: Dynamic DNS Service Applying In E1000

May 2, 2012

I have applied for a dynamic dns service,  but need applying in linksys E1000 settings 

View 3 Replies View Related

How To Set Up NetGear WNDR3400v2 As A Repeater

May 23, 2012

I have a netGEar WNDR3400v2 wireless router which I want to set up as a base station and use the same model router as a repeater to extend my wireless range to the other end of my house?

View 2 Replies View Related

Netgear Wndr3400v2 - Port Tracker Is Closed

Aug 8, 2012

I have followed all instructions to forward port 22 on my netgear router WNDR 3400v2. It says it forwarded but according to port tracker. Its closed. I am having this with two different locations. All IP addresses are correct and the router can ping them. It just wont open. Using SSH program for port 22 access.

View 10 Replies View Related

WNDR3400v2 - After Enabling And Disabling Guest Network Nothing Will Connect

Oct 9, 2012

I purchased a WNDR3400v2 probably around two months back and since then I haven't had any issues with it. Now, I like to keep the security setting on WPA2-PSK for the security but my brothers and my own Nintendo DS don't support this security for connecting. So, since my previous router had a guest network, I decided to activate and deactivate that network with no security when it was needed (Half hour or less), and I haven't had any issues until doing this with the WNDR3400v2.

Basically what happens is, after disabling the guest network again, no wireless devices can connect to the router... PERIOD... Upon trying to connect it also says "You are unable to connect) right after it verifies the password. I spent a few hours trying to fix it but I haven't gotten anywhere really..

What I have tried-v

-Resetting the Router

-Powercycling the Router

-Resetting it to factory defaults and restoring previous settings

-Enabling and disabling the network

-Deleting the original network saved on the computers and connecting as if from a new network.

-Also tried restarting my computers

-Updating the firmware (For some odd reason I couldn't find any firmware last week..)

I researched it a bit and found some solid leads, but nothing that fixed the issue. The only "Fix" I could find was disabling the security and leaving it open.. Which I would prefer not to do for obvious reasons...

Router Type: Netgear Wireless Dual-Band N600 Router (WNDR3400v2)
Firmware: V1.0.0.34_1.0.52

View 2 Replies View Related

WNDR3400V2 Box To Allow Guest To Access Local Network Grayed Out

Oct 11, 2012

I got a problem with my netgear WNDR3400V2.As u see in this picture the box allow guest to access my local network is greyed out.I made the router an access point and have no clue how to make it normal again.

View 2 Replies View Related

Cisco Firewall :: ASA 5510 / Ip Service Object And Service Group

May 16, 2011

When I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
 
my ip service object
object-group service g-as400 description access client 2 as400 machine service-object tcp-udp destination eq 397 service-object tcp destination eq 137 service-object tcp destination eq 2001 service-object tcp destination eq 3000 service-object tcp destination eq 445 service-object tcp destination range 446 447 service-object tcp destination eq 449 service-object tcp destination eq 5010 service-object tcp destination eq 5544 service-object tcp destination eq 5555 service-object tcp destination range 8470 8476 service-object tcp destination eq 8480 service-object tcp destination eq

[code]...

View 8 Replies View Related

Cisco Application :: ACE 20 Service-policy Out Of Service / Still Able To Connect To VIP

Feb 28, 2012

We have a situation where services are stopped on the real servers. The probes fail and we confirm the services are not running on the server. We cannot access the ports from the ACE directly. We can still however acces the VIP on the TCP port (L4 VIP class-map). So we can still telnet to the VIP on the port from thr Client side of the network.This is on ACE 20 Modules deployed in Routed mode. The version of software is A2(3.3).
 
Tried removing multi-match and loadbalance policies as well as class-map and re-applying then re-appyling the service policy to interface. Same behavior,This is a problem at another level as some services are being monitored by GSS via TCP keep-Alive and this obviuosly causes a problem as the service then never goes off-line.

View 10 Replies View Related

Cisco :: Topology Service In LMS 4.0 / ANIServer Service May Be Down

Mar 25, 2013

I have a fresh installation of LMS 4.0 on windows server 2003, when i click to open topology i get error message : ANIServer service may be down or Host name isn't DNS resolvable
 
i tried pdshow -brief ANIServer ===> service UP

DNS is working using host file in driversetc i restarted the server

restared the crmdmgtd
unistall / install java plugin
pdterm ANIServer
pdexec ANIServer
 
NO change ..

View 6 Replies View Related

DNS Server May Not Be Available - Contact Provider

Jun 6, 2012

I have a Time Warner modem/router. There are a ton of different devices constantly being connected/disconnected to our router - itouches, computers, smartphones etc.

The problem started with my otherwise super reliable HP g42 (i3) laptop. Nothing would solve the issue other than recovering it back a few days to when the issue wasn't happening. But then it would happen again after a few days. All other devices would connect without issue.

Time warner's technical troubleshooting consists of "unplug the router for 10 seconds and then plug it back in. Did that work?"

So now, my son gets his first computer and I bring it home last night. Also an HP (pavillion -i3). Same deal. At first, it connects fine and dandy. Then after about 2 hours it get the ol' "won't connect - diagnose the problem?" After diagnose, it says "DNS server may not be available.

Here's the thing: Both computers connect immediately and without issue to my smartphone wireless tether.

View 6 Replies View Related

Get IP Address To Be Able To Use Internet Provider?

Nov 18, 2011

My internet service is telling me all of a sudden that my computer has no IP address for my laptop to connect to the modem?? The laptop was given to me so I have none of the disks or anything. How do I get an IP address to be able to use my internet provider?

View 2 Replies View Related

How To Setup A Network Provider

Feb 22, 2011

how do set up a network provider so i can send and receive E-MAIL i use XP

View 1 Replies View Related

Connect Two Dsl Connection With 2 Different Provider?

Nov 16, 2012

who to connect two dsl connection with two different provider

View 1 Replies View Related

Wireless :: Cannot Get Printer To See Provider In Setup

Oct 13, 2011

using t-mobile dongle on laptop to get internet but hp printer wont see provider in setup.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved