WNDR3400V2 Box To Allow Guest To Access Local Network Grayed Out
Oct 11, 2012
I got a problem with my netgear WNDR3400V2.As u see in this picture the box allow guest to access my local network is greyed out.I made the router an access point and have no clue how to make it normal again.
View 2 Replies
ADVERTISEMENT
Oct 9, 2012
I purchased a WNDR3400v2 probably around two months back and since then I haven't had any issues with it. Now, I like to keep the security setting on WPA2-PSK for the security but my brothers and my own Nintendo DS don't support this security for connecting. So, since my previous router had a guest network, I decided to activate and deactivate that network with no security when it was needed (Half hour or less), and I haven't had any issues until doing this with the WNDR3400v2.
Basically what happens is, after disabling the guest network again, no wireless devices can connect to the router... PERIOD... Upon trying to connect it also says "You are unable to connect) right after it verifies the password. I spent a few hours trying to fix it but I haven't gotten anywhere really..
What I have tried-v
-Resetting the Router
-Powercycling the Router
-Resetting it to factory defaults and restoring previous settings
-Enabling and disabling the network
-Deleting the original network saved on the computers and connecting as if from a new network.
-Also tried restarting my computers
-Updating the firmware (For some odd reason I couldn't find any firmware last week..)
I researched it a bit and found some solid leads, but nothing that fixed the issue. The only "Fix" I could find was disabling the security and leaving it open.. Which I would prefer not to do for obvious reasons...
Router Type: Netgear Wireless Dual-Band N600 Router (WNDR3400v2)
Firmware: V1.0.0.34_1.0.52
View 2 Replies
View Related
Jul 10, 2012
my computer was on a lan but suddenly stopped to be part of it.The other coms can see him on the network but mine one cant see anybody.I ve tried everything is written on this site and everywhere on the net but the problem remains.The network id tab is still disabled.im running xp pro,no media center and my antivirus is kaspersky.
View 2 Replies
View Related
Aug 18, 2011
Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies
View Related
Apr 22, 2012
I'm a member of a club and we have just got BT Business Broadband with BT Business Hub 3. The club has one WiFi laptop which will occasionally access the BT Hub 3 using WiFi for internet use only. So essentially we have no network as such, just the BT Hub and a laptop.I would like to allow some club members to have internet access (WPA2 password), but without allowing access to the club laptop in any wayAs I said previously, the club laptop will only be active occasionally, so actual exposure is limited, but ideally I would like for the club laptop to be invisible to others when it is connected. I would also like each members equipment to be hidden from each other, so nobody can access each others data etc.. Can I achieve this simply? If so, do I need extra equipment?
I do have some donated equipment available: Netgear WAG102 Wireless Access Point, D-Link DSL-2640R Broadband Wireless G ADSL2+ Router and US Robotics 9106 SureConnect ADSL Wireless Gateway. Could I use any or all of these?I know this donated equipment is only Wireless G, but speed for the members is not important as they will only use internet access for emails and occasional google searches etc.I've tested the WAG102 at home, by plugging it into a LAN port of my BT HomeHub3 and giving it a different SSID, which works OK, but I can still see the other equipment connected wirelessly to my BT HomeHub3, although I cannot access my home laptop etc. because they are password protected.
View 3 Replies
View Related
Mar 23, 2011
We have a 4402 wlc setup for guest network access. We are using the local net users to provide access to our guests. We have an issue where if a user signs in through the web, sometimes but not always, they are then forced to keep signing back in almost every 30-60 seconds.
View 8 Replies
View Related
Apr 19, 2011
I have two Cisco WAP4410N access points. Both has Regular and Guest SSIDs, with same configurations, except "Wireless Isolation" on Guest SSID is enabled. Problem is Guest SSIDs are not visible on devices
Access points are working on different chanles, firmware Version: 2.0.1.0.
View 5 Replies
View Related
Oct 29, 2012
I have going up the walls the last week.Basically just moved house and got broadband installed, my girlfriends laptop connected automatically, whereas my Compaq CQ60 Presario Notebook WindowsVista will not connectI have checked so many different forums trying to fix this problem, but to no avail im afraid... it looks like there is an excellent internet connection.... but cannot go on the internet because it says "Unidentified Network local access only"
View 6 Replies
View Related
Apr 18, 2012
I want to Turn off my local network's firewall on my computer but i dont know how.
View 1 Replies
View Related
Dec 11, 2011
I tired connecting my Sony TV to the internet.It wouldn't connect automatically so I manually entered
IP Address 192.168.1.200
Subnet Mask 255.255.255.0
Default Gateway 192.168.1.1
Primary DNS 192.168.1.1
Secondary DNS 0.0.0.0
When it tested that it only gave me local access but not internet access. What else can I do to fix this? I use a netgear router WPN824N.
View 3 Replies
View Related
Nov 26, 2011
I just replaced my wireless router. Wh? Now I'm not sure, I hoped a dual band router would give me better range. True or false?Regardless, I installed my new router but can only connect to my local network on my home laptop. However my work laptop connects to the same network and internet with no problem. SO does my husband's work computer.Any idea what the problem is? Other weird thing is that I have some random unsecured network that keeps popping up and my computer keeps automatically connecting. I've tried to remove it every way possible and it keeps coming back?
View 1 Replies
View Related
May 7, 2012
I have recently set up a computer on my network to host a website.So i have done the basics and created a Dyndns account etc.Now I can view the website via this domain flyingant.dyndns.org/ on computers outside of the network and the pc that it is hosted on.But my problem is that I cannot view the website on any other computer on the network, it takes me to the routers login page.
View 2 Replies
View Related
Feb 28, 2013
I have created a new sub-interface on our ASA 5520 for guest internet access.
My goal is to allow access to a few specific services hanging off some dmz interfaces on the same firewall and full unrestricted access to the internet only. Everything else should be out of bounds.
The order of the rules I plan to setup on the guest interface inbound are:
#1. <rules to allow access to specific services in the dmz>
#2. <block any ip access to the entire private network ip address space>
#3. <permit ip any any>
#1. These rules will give access to the guest user to services located in the dmz
#2. This rule will block all access to any services in the private ip address space (thus blocking access to all internal services)
#3. This rule is to allow access to any other services i.e. the internet.
Is this the best way to achieve my goal in the most secure way or is there a better way? i.e. is there a way to force the traffic by default to only go out the outside interface unless there is a specific rule allowing it go elsewhere?
(Of course Dynamic PAT will also be configured for traffic coming from the guest interface to the outside interface.)
View 2 Replies
View Related
Jul 20, 2011
We have an RV042 as main router.We have a netgear WNR2000v2 as WIFI router.We would like to offer our drop-in customers an internet access. But without letting them into our network.
View 1 Replies
View Related
Mar 6, 2013
We have the RV180W router and the WAP321 access point in our business. We want to broadcast two SSIDs from both locations: the office SSID, which shares routing to LAN traffic, and a guest SSID.The office computers are attached via ethernet to a switch off of LAN port 1 on the router. The AP is attached to LAN port 2 on the router.On the router, the office SSID and the LAN are members of VLAN 1. The guest network is a member of VLAN 2. From the router, everything works just fine.On the WAP, the staff SSID works fine, but the guest SSID has no internet. Both the office and guest networks get DHCP successfully from the router.Our VLAN membership table in the router and WAP are attached, as well as other configuration details.Why would we not be getting internet on the guest ID only on the WAP?
View 8 Replies
View Related
Dec 26, 2011
I need to know how WLC can support ISE guest management in wireless mode. Tested and confirm by Cisco SE, Knowing that WLC currently does not support dynamic VLAN authorization for central web authentication. This limitation will be addressed in WLC 7.2 when MAB and CWA support is added to the code. On the other hand, DACLs on the other hand works and we can use that to restrict access of this guest traffic.Can ISE support on WLC LWA guest access provision? This able to view guest user login and show at ISE monitoring.
View 1 Replies
View Related
Oct 17, 2012
Any problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies
View Related
Dec 18, 2012
I have the syntax correct and thought process down right on a solution to allowing guest wireless users access to an internal webserver. (DMZ discussion aside)
We have an ASA5510 with interfaces setup as:
outside - 65.x.x.x address
inside - 172.20.1.2
guest_inet - 10.2.1.1
Internally clients resolve our website to 192.168.40.40 and that part works as it should. Clients outside of our network resolve our website to the correct external address (lets just call it 1.1.1.1). We have a NAT statement static (inside, outside) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 and an ACL to permit tcp any host 1.1.1.1 eq www
Clients on our guest_int use an external DNS server and hence resolve our website to 1.1.1.1. However it seems traffic goes out and back in our outside interface and this connection never occurs.
What I'm wondering is the correct NAT statement / ACL to add that would allow our internal clients on the 10.2.1.x network to access our internal website. Would that be: static (inside,guest_inet) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 ? Since there is already an ACL permitting port 80 traffic to 1.1.1.1 we should be taken care of on the ACL side of things, right?
View 3 Replies
View Related
Aug 11, 2012
I've got two EA4500 routers connected via Ethernet. The primary router has DHCP enabled and the secondary has it disabled. IP address of primary is 192.168.1.1 and the secondary is 192.168.1.2.
I have set up guest access on both routers however only the primary router allows users to connect. When out of range of the primary router but in range of the secondary router the network is visible but when you try to connect to it, it only gives limited or no connectivity message and can't connect to the internet.
Is it possible for the guest network access to follow the same pattern as the secure network, i.e. the same network throughout the house?
View 9 Replies
View Related
Nov 13, 2012
Local Access Only on Vista PC
I restored an old Vista laptop to out-of-the-box state to give to my Dad. This laptop had a wireless connection to the internet and network previously. After the restore, I can't get a connection to the internet, even though my router sees it and it has an ip address. It says Unidentified Network Local Access only, and it doesn't see any of the computers on the network. Sometimes the other computers see it but can't connect, sometimes, the other computers don't see it. I hate Vista.
Stats on Laptop:
Toshiba A215-S4747
Atheros AR5007EG
All my other eight devices have an internet connection no problem, but I powered off the modem and router a couple of times with no change. I tried updating the Atheros to the latest driver on Toshiba's website for this model, but it doesn't seem to take. If I uninstall the old drivers, Windows rudely just immediately reinstalls them again. If I just update the driver, and pick the new file, the driver version remains the same as the previous driver. I'm banging my head on the wall with the driver
Ping successful on:
192.168.1.11 (the laptop's IP address)
localhost
[Code]......
View 11 Replies
View Related
Oct 18, 2011
i have a problem with my asa 5505 Remote VPN Connection with local network access , the VPn is working fine and connected , but the problem is i can't reach my inside network connection of 192.168.30.x , here is my configuration
ASA Version 8.2(1)
!
!
interface Vlan1
[Code].....
View 13 Replies
View Related
May 6, 2013
I have setup an aironet 1262 with my ASA 5512 and configured it as an access point. I would like to add an additonal network to the ap for guests to use but I would like to segregate the traffic and only allow it to the internet. I am not sure how to start this and go about setting the routes, security and address scope.
View 1 Replies
View Related
May 23, 2012
I have a netGEar WNDR3400v2 wireless router which I want to set up as a base station and use the same model router as a repeater to extend my wireless range to the other end of my house?
View 2 Replies
View Related
Sep 17, 2011
My computer is running on Windows 7. It has had no prior internet connection problems. It is wired to my DV-2020 router. My internet suddenly disappeared, as in, it doesn't work anymore. I'm not sure as to when it disappeared due to my personal absence, but from what I heard it was either during 'starting a game' or 'installing firefox add-ons updates'. Internet does work on other computers sharing the same internet (wired and wireless). On the computer that does not have access to internet it gives a "local area connection - No Network Access" and "local area connection - unidentified network." So far I've tried:
A system restore.
Restarting the router (at home as well as the provider)
Changing wiring.
Disabling / Enabling.
Disabling virusscanner.
View 19 Replies
View Related
Mar 13, 2011
What I'm trying to do is create a private network for local file sharing but also have internet access. There is a WRT54G router connected to a satellite modem in a separate building, just barely close enough to connect from my laptop, which is what sparked my original idea to use my WRT54GL as an access point.
View 1 Replies
View Related
Jan 16, 2013
I configure anyconnect vpn on cisco asa version 8.2. vpn user need to access internet so i configured split-tunnel. the split-tunnel working but i do not want to use split-tunnel for security reason. i want vpn user use our local network internet. how i do it?i think that i must do vpn user subnet nat and then what i need do additionally?
View 1 Replies
View Related
Jul 20, 2011
We have SSL VPN using the AnyConnect client going to an ASA5540.
Is there a way to permit users to access their own LAN, but still force them to use the VPN tunnel for Internet access?
If I'm reading the documentation correctly, it seems that when you activate split tunnelling, it allow LAN access, but will also allow the user to access the Internet over the LAN instead of over the VPN.
View 1 Replies
View Related
Jan 23, 2012
We have a Cisco wireless infrastructure in place that includes a guest network with its own subnet that is a sub interface of the inside interface on our ASA 5520. There are no routes for it to be allowed access to the internal subnets. So it can only access the internet. This is primarily used by the public, but we have several non employee personnel that we only want to give internet access and force them to access the internal network through our clientless SSL vpn portal or through other internet facing internal resources such as webmail.I have done packet traces from within the ASA and the break appears to be there is no ACL allowing the traffic back into the network once the web resource replies to the request and the traffic is attempting to come back into the network from the web resource. Is that as clear as mud?
I know that this has to be a common problem and a way around this is to allow the guest wireless network access to the internal network but only for the select resources that they require. And that this can be done seemlessly by network specific routes and or alternate DNS entries, but I would like to keep this simple and just allow them to access the web resource, webmail and VPN, from the guest wireless using internet DNS servers without route trickery.
View 8 Replies
View Related
Jul 22, 2012
I have DNS setup through No-IP.com. How do I add this service provider to my WNDR3400v2 router? It only has DynDNS.org listed and I can't create a free account there.
View 1 Replies
View Related
Dec 25, 2011
The issue is Windows7 (notebook ASUS N61Ja connected through Wi-Fi) loses and can not find again network HDD storage (Western Digital My Book Live 3TB). Rebooting of the notebook works but after I close HDD folder window the issue comes back. The issue exists only with Wi-Fi connection. Everything is fine using LAN connection.
View 1 Replies
View Related
Mar 14, 2013
I have a Cisco ASA 5510 I am using ASDM 6.1
I have a LAN and a DMZ and an internet connection. I am using one of the internet connection IPs to host a HTTP service on a server in my DMZ. (its the same interface as my internet connenction but a different IP to the one used for internet connectivity)
so say my LAN is 192.168.1.x
and my DMZ is 172.168.1.x
I can access DMZ from Lan and vice versa. when i try to access the public IP (or URL) from a pc in my LAN i get nothing.
I have enabled DNS rewrite (doctoring) but it is still not working. the HTTP service is available from other sites.
View 1 Replies
View Related
Jun 10, 2011
I configure for our office site to site VPN project. Now I configured already Site to site vpn between ASA 5510 and 1841 router.
HQ LAN
Branch LAN 10.2.1.0/24 >>> ASA 5510>>>>> 1841 >>> INTERNET <<<<<< 1841 <<<<<< 10.30.3.0/24 ^^^^ Call Manager 2851
Now can access from Branch LAN to HQ LAN each other. I face the problems that are
1) In branch LAN , they can access HQ LAN & resource , but cannot access internet. I didn't configure NAT on PH Router
2) Can I access internet from BRANCH LAN through HQ LAN to INTERNET. Or Can I access Internet from Branch LAN from PH Router directly while access to VPN to HQ LAN ?
3) In Branch Site , hard phone cannot work but soft phone on PC can call to HQ. Hard phone IP are same in Remote Network (172.16.1.0/24 ) . Is it problem ? how can I configure separately ?
View 2 Replies
View Related
Feb 15, 2012
I recently took my Dell Inspiron1545 out of sleep mode and my wireless internet connection no longer works.i have tried power cycling the 2-wire modem and the Cisco Valet router and resetting as well. I also have another laptop and xbox that use this network and are having NO issues in connecting and working perfectly fine.
The only device not working is the Dell laptop. I've tried removing the network profile, uninstalling the wifi driver and reinstalling after powercycling the computer and still nothing but limited connectivity only The WLAN utility has stated that the "Gateway IP Ping" has failed Now the laptop will connect to internet via LAN cable however will not to WiFi
I have attached the IPconfig spec sheet and hopefully somewhat can steer me in the right direction and get me back up an running.
Windows IP Configuration Host Name . . . . . . . . . . . . : Zee-PC Primary Dns Suffix . . . . . . . : Node Type . . . . . . . . . . . . : Hybrid IP Routing Enabled. . . . . . . . : No WINS Proxy Enabled. . . . . . . . : NoWireless LAN adapter Wireless Network Connection: Connection-specific DNS Suffix . : Description . . . . . . . . . . . : Dell Wireless 1397 WLAN Mini-Card Physical Address. . . . . . . . . : 00-22-5F-BF-40-AB DHCP Enabled. . . . . . . . . . . : Yes Autoconfiguration Enabled . . . . : Yes Link-local IPv6 Address . . . . . : fe80::8830:577f:a3fc:6333%15(Preferred)
[Code] ........
View 3 Replies
View Related