Home Network :: How To Allow Guest Access For Internet Use Only
Apr 22, 2012
I'm a member of a club and we have just got BT Business Broadband with BT Business Hub 3. The club has one WiFi laptop which will occasionally access the BT Hub 3 using WiFi for internet use only. So essentially we have no network as such, just the BT Hub and a laptop.I would like to allow some club members to have internet access (WPA2 password), but without allowing access to the club laptop in any wayAs I said previously, the club laptop will only be active occasionally, so actual exposure is limited, but ideally I would like for the club laptop to be invisible to others when it is connected. I would also like each members equipment to be hidden from each other, so nobody can access each others data etc.. Can I achieve this simply? If so, do I need extra equipment?
I do have some donated equipment available: Netgear WAG102 Wireless Access Point, D-Link DSL-2640R Broadband Wireless G ADSL2+ Router and US Robotics 9106 SureConnect ADSL Wireless Gateway. Could I use any or all of these?I know this donated equipment is only Wireless G, but speed for the members is not important as they will only use internet access for emails and occasional google searches etc.I've tested the WAG102 at home, by plugging it into a LAN port of my BT HomeHub3 and giving it a different SSID, which works OK, but I can still see the other equipment connected wirelessly to my BT HomeHub3, although I cannot access my home laptop etc. because they are password protected.
View 3 Replies
ADVERTISEMENT
Mar 6, 2013
We have the RV180W router and the WAP321 access point in our business. We want to broadcast two SSIDs from both locations: the office SSID, which shares routing to LAN traffic, and a guest SSID.The office computers are attached via ethernet to a switch off of LAN port 1 on the router. The AP is attached to LAN port 2 on the router.On the router, the office SSID and the LAN are members of VLAN 1. The guest network is a member of VLAN 2. From the router, everything works just fine.On the WAP, the staff SSID works fine, but the guest SSID has no internet. Both the office and guest networks get DHCP successfully from the router.Our VLAN membership table in the router and WAP are attached, as well as other configuration details.Why would we not be getting internet on the guest ID only on the WAP?
View 8 Replies
View Related
Jan 26, 2012
i would like to know that how to stop internet access through network complete internet access
View 2 Replies
View Related
May 6, 2013
I have setup an aironet 1262 with my ASA 5512 and configured it as an access point. I would like to add an additonal network to the ap for guests to use but I would like to segregate the traffic and only allow it to the internet. I am not sure how to start this and go about setting the routes, security and address scope.
View 1 Replies
View Related
Oct 29, 2012
Having an issue with a Cisco Linksys E1500 on a home network. The device has a feature to provide a guest wireless network but the guest network can't get to the internet. A wired connection is fine, as is the normal wireless network but not the guest. The cheesy thing is, that it doesn't list an option for what type of wireless security protocol you want on the guest network. I'm assuming that it uses the same security protocol that the normal wireless network uses, but who knowsEspecially weird is that it asks you what password you want on the guest network but then the guest network show to be insecure when you try to connectthought maybe it was something funky with some of my configurations so I went ahead and factory defaulted it and just set it up with an insecure network for both the normal and guest networks. This didn't solve it. The guest network still couldn't get to the internet. In fact, the guest network can't even ping the router.
View 1 Replies
View Related
Sep 8, 2011
Since yesterday im unable to connect to the wireless connection in my dormsI'm able to connect but i get yellow triangle with exclamation mark in it, and it says "no internet access".In the living room im able to gain internet access, my friend also tried in my room and he was able to get internet access, he has tp-link adapter on his laptop.I have dell vostro 3500 with "DW1051 wireless-N WLAN half-mini card" as my adapter.I opened IE9 and pressed "Diagnose connection problems" and got the messege "Wireless Network connection" does not have valid IP configuration.OS: windows 7 ultimate x64
View 6 Replies
View Related
Feb 8, 2012
i have an internet connection thrw USB from a ppp adapter from there i've made a netowrk with another computer now on the client computer from my network i have XAMP server who i want to be accessed from the internet .i have subdomain like radionis.zapto.org (192.168.0.2) registered at no-ip.org.now what IP i have to introduce there to make my server accessible
View 2 Replies
View Related
Jun 30, 2011
I have been using a laptop to stream videos through my xbox for over 2years until recently. I setup a wireless network in the house to do this. All was fine until 3 days ago.I use a Dell Inspiron 1545 with Windows 7. I have a Dell Wireless 1397 Minicard, a cisco router (model #2425). Since my laptop was infected by Malware, my network has not worked since. I downloaded Malwarebytes Anti Malware to get rid of it and it appeared to work. I got internet access back. However, I still cannot connect to my network (visible in the Available Network list as normal) or stream any media.Windows Media Centre also has stopped opening and gives me the small box saying 'windows is checking for a solution', then closes with nothing. I can however open WMC if I right click and 'run as administrator'?! I have disabled all other network adaptors, only the Dell minicad is enabled and also tried disabling and enabling this main one with no effect. All problems point to the fact that my laptop can no longer connect to the home network but I cant figure out why?!Another (possibly unrelated) problem is occuring at boot up where I get an error message saying 'Bluetooth Software License not found. [2]' - Again this never happened before the Malware infection.
View 1 Replies
View Related
Apr 27, 2012
I managed to flash my router (Belkin Sharemax N300) to dd-wrt and set it up as a repeater using these steps in the wiki, but I can't access the internet via the repeater. I can still connect to it, though. I don't know that much about networking.
View 1 Replies
View Related
Jun 19, 2011
Currently I'm living in a dorm. The house has wireless network. But WEP encryption is used to secure it. I know this method is not safe. Also since there are many people are living in the house i don't want my computers be connected to this network.What i want to do is to setup my own network. I bought a NetGear DGND3300 router. I setup a WPA2 protected wireless network. I can connect all my devices to this network but naturally this way i have no Internet access.Is there a way to use Internet access of the house's router but still keep my local traffic not seen by anybody else
View 2 Replies
View Related
Nov 24, 2011
Orange sent me a replacement Netgear DNG1000 and from the moment I had it there was issues, if N mode was enabled and I had to set it to B/G only for it to have a stable connection, not a problem as I only use it for the internet. The range on it was roughly the same as the livebox. For a few weeks it worked fine until recently it started to go insane, on the main computer the wifi works most of the time with 80%-95% signal strength, and then every now and then it will suddenly lose communication with the router but act as if it was connected for 5-10 minutes, signal strength is still at about 90% yet I can't access the router or the internet. Wifi works fine at full speed on the stairs, drops to a few bytes per second on the landing and then increases back up to full speed in the room next to it. In the one bedroom the wifi works up until the door where it instantly drops from full speed to a few bytes a second. This drop off point is only a few cms, as in full speed at one place, move it back a few cm and it slows down loads, but I still get 4-5 bars on windows and -50 RSSI on inSSIDer, about 94% strength and a link quality which tends to fluctuate. What could be causing this, specifically the weird instant deadzones and randomly not responding.
View 1 Replies
View Related
Jun 17, 2011
I would like to have the ability to turn off the internet access to my teens computers without effecting myself. I have parental controls on my computer which work great, but this does not work to the other computers that are able to connect wirelessly. I have a router but I am not sure how to access it.
View 3 Replies
View Related
Feb 18, 2012
I am running a VPN server on my desktop at home, with all the default settings, and i checked the box that allows clients to connect over the internet. this is win7 x64 computer. I opened up port 1723 with PPTP protocol on my E4200 router.On the client i am running win7 x64 as well. I am able to connect to the vpn, from another internet connection, but there is no local network acess. It says the status is No Internet Access. and the IP that is assigned is the 169.x.x.x one that windows defaults when it doesnt find a dhcp server.How can i get the client to connect with full local network access. Right now being connected to the vpn, it means nothing, i have no access other than being "connected".
View 1 Replies
View Related
Aug 23, 2011
i'm having an issue with a computer on my home network (Windows XP Professional SP3, latest updates) where i can't access the Internet or even the router on my home network (which it is part of).if i look at the network connection (wired) under control panel it shows as connected, and it's set with a static IP address (always has been), so nothing looks out of the ordinary there, yet if i try opening Internet Explorer i just get the "page cannot be displayed" page, and i can't even ping my own router- request times out.I've tried connecting a wireless adapter that i use on my laptop every day.. it connects to the wireless network no problem, but still the same results with IE and pinging the router.
View 4 Replies
View Related
Jan 31, 2013
I am experiencing problems trying to access my routers HTTP-type configuration. I have a Billion 400G router. The address to access the router was always http://10.0.0.2 and that has always worked. A dialog box would appear asking for a username and password. Now it doesn't even reach that screen. It says that the connection timed out. I've tried Firefox/Chrome/IE10. To no avail. My system: Windows 8 build 9500. Also something weird. When I type in this Microsoft thing comes up with IIS 8.
View 2 Replies
View Related
Apr 1, 2013
It is a Satelite 733. Have pinged without any response however the wifi or hardwire will show connected to the local net.I have four other units surfing the web fine and wifi picks up ok except for one unit that my neighbor need will not connect no matter what. Have updated all the drivers, uninstalled and re-installed devices, reset ip, dumped the dns several times, etc.So here is the ipconfig stuff....ignore the cable connect I only have the wifi on at the moment. I have stared at this to the point where I know naathing .Is the tunnel adaptor the indication that the card is out? Oh and I tried taking out IPV 4 on both channels and nothing so I left one with 4 on and the other with it off just as something else to try. [code]
View 2 Replies
View Related
Apr 26, 2011
The problem that I am facing is while accessing internet.I have replaced the LAN card also. It sends request but receives nothing. The cable line is also working fine
View 5 Replies
View Related
Jan 30, 2013
1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled) 2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the samesubnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it
View 4 Replies
View Related
Jun 6, 2012
I am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
View 2 Replies
View Related
Mar 10, 2011
I'm setting up a small network (one server, two clients) to create photo sales kiosks at an upcoming outdoor event. I will need internet access for processing credit card payments but there won't be any wi-fi or ethernet internet access on the site so I'll need to utilize my iPhone's 3G connection. I recently installed "MyWi" app which can tether the 3G and even create a personal wi-fi hotspot but unfortunately it only works in ad-hoc mode, not infrastructure.So far, the wired LAN is working great on my three Macbooks, using a Linksys (DD-WRT) router. Also, the wi-fi hotspot is working great to provide internet to all the computers. The problem, of course, is that I can't have both connected at the same time or else everything breaks. I've tried doing an iPhone-USB-Macbook tether and then sharing the connection via ethernet but the internet doesn't get through the router (because I don't have a clue of how to configure the router for this). I've also tried setting my router (DD-WRT) to do a client-bridge of the iPhone ad-hoc wi-fi, but again, it's way over my head and didn't work.
View 2 Replies
View Related
Aug 3, 2011
Was told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 3 Replies
View Related
Aug 18, 2011
Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies
View Related
Apr 13, 2013
I just bought a Netgear Router WNR 2000 v3 and installed it. I got inside the router and could set up a Network Name and security key. However, I can not access the internet when I chose a security password using WPA 2, WPA-PSK + WPA 2 PSK, or WPA/WPA 2. It only accesses the internet when I chose None.( no secured ).At this time, my network is unsecured because there isn't way I can access the internet when I create a security key using the 3 options the router offers.
Note : I have tried the 3 security options creating a key number and my computer connect to the wireless network but don't access the internet. It only access the internet when I select None ( no secured )
View 2 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Dec 13, 2012
Here is my setup:
Netgear WNDR3700 - Main router, DHCP turned on
4x Netgear WNR2000 - Setup as Access Points (DHCP turned off), connected to main router via LAN ports
I only want the guest network to have internet access. I have the guest network enabled on the router and access points with the option to "Allow Guest network to access main network" disabled. My problem is that since the access points aren't hooked directly to my modem via the WAN port, the guest network broadcasted from the access points does not have internet access.I have read up on setting up a separate subnet for the guest network using DD-WRT but was curious if there was a way to get the desired result with the stock Netgear firmware.
View 9 Replies
View Related
Oct 3, 2011
I have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies
View Related
Mar 23, 2011
We have a 4402 wlc setup for guest network access. We are using the local net users to provide access to our guests. We have an issue where if a user signs in through the web, sometimes but not always, they are then forced to keep signing back in almost every 30-60 seconds.
View 8 Replies
View Related
Oct 11, 2012
I got a problem with my netgear WNDR3400V2.As u see in this picture the box allow guest to access my local network is greyed out.I made the router an access point and have no clue how to make it normal again.
View 2 Replies
View Related
Apr 19, 2011
I have two Cisco WAP4410N access points. Both has Regular and Guest SSIDs, with same configurations, except "Wireless Isolation" on Guest SSID is enabled. Problem is Guest SSIDs are not visible on devices
Access points are working on different chanles, firmware Version: 2.0.1.0.
View 5 Replies
View Related
Oct 28, 2011
I am running a 5508 WLC with 10 Access Point. we need to allow Internet Access to Guest. 10MB DSL Internet is dedicated for Guest. This link is terminated on a regular ADSL modem without being part of our network. We want all Guest Internet traffic to reach the ADSL Router. where should I create the Guest VLAN / where the DHCP for Guest users should be created. what is the best practise for similar setup.
Our Network is simple
ISP_Reuter-------ASA_Firewall--------------4505------------LAN-switch 2950
ADSL_modem------------ users connect via wireless but restricted to certain area only.
View 9 Replies
View Related
Feb 28, 2013
I have created a new sub-interface on our ASA 5520 for guest internet access.
My goal is to allow access to a few specific services hanging off some dmz interfaces on the same firewall and full unrestricted access to the internet only. Everything else should be out of bounds.
The order of the rules I plan to setup on the guest interface inbound are:
#1. <rules to allow access to specific services in the dmz>
#2. <block any ip access to the entire private network ip address space>
#3. <permit ip any any>
#1. These rules will give access to the guest user to services located in the dmz
#2. This rule will block all access to any services in the private ip address space (thus blocking access to all internal services)
#3. This rule is to allow access to any other services i.e. the internet.
Is this the best way to achieve my goal in the most secure way or is there a better way? i.e. is there a way to force the traffic by default to only go out the outside interface unless there is a specific rule allowing it go elsewhere?
(Of course Dynamic PAT will also be configured for traffic coming from the guest interface to the outside interface.)
View 2 Replies
View Related
Jul 20, 2011
We have an RV042 as main router.We have a netgear WNR2000v2 as WIFI router.We would like to offer our drop-in customers an internet access. But without letting them into our network.
View 1 Replies
View Related
Dec 26, 2011
I need to know how WLC can support ISE guest management in wireless mode. Tested and confirm by Cisco SE, Knowing that WLC currently does not support dynamic VLAN authorization for central web authentication. This limitation will be addressed in WLC 7.2 when MAB and CWA support is added to the code. On the other hand, DACLs on the other hand works and we can use that to restrict access of this guest traffic.Can ISE support on WLC LWA guest access provision? This able to view guest user login and show at ISE monitoring.
View 1 Replies
View Related
