I managed to flash my router (Belkin Sharemax N300) to dd-wrt and set it up as a repeater using these steps in the wiki, but I can't access the internet via the repeater. I can still connect to it, though. I don't know that much about networking.
View 1 RepliesI am looking for an equipment recommendation for setting up an access point/repeater for my home network.
I have comcast > surfboard > d-link dir 655 I want to add another router/access point so I can move the dir655 to my office and have my computers connected over gigbait. All my comcast stuff is setup in the living room, and I would like to setup the access point there. Something like
comcast > surfboard > ddwrt n-router (living room) > dir655 (in office) > desktop
i would like to know that how to stop internet access through network complete internet access
View 2 Replies View RelatedI have a newer N Router (Dlink DIR-655) and the wireless signal coming off of it, just isn't strong enough. I was planning on using the WTF54GL to repeat the signal and inturn increase the coverage area. I've installed the latest version of Tomato on there (v1.28) and have gone through setting it up as a wireless client, wireless ethernet bridge (which works for picking up the wireless signal and then plugging something in via ethernet has internet), access point, access point + wds and just wds. None of which I can get to seem to properly repeat the wireless signal with internet connectivity. I have both routers set to G only channel 6, WPA Personal, Is this even possible? Or do I need a router that can run the tomato firmware on the main (host) router that is connected to the net?
View 1 Replies View RelatedSince yesterday im unable to connect to the wireless connection in my dormsI'm able to connect but i get yellow triangle with exclamation mark in it, and it says "no internet access".In the living room im able to gain internet access, my friend also tried in my room and he was able to get internet access, he has tp-link adapter on his laptop.I have dell vostro 3500 with "DW1051 wireless-N WLAN half-mini card" as my adapter.I opened IE9 and pressed "Diagnose connection problems" and got the messege "Wireless Network connection" does not have valid IP configuration.OS: windows 7 ultimate x64
View 6 Replies View Relatedi have an internet connection thrw USB from a ppp adapter from there i've made a netowrk with another computer now on the client computer from my network i have XAMP server who i want to be accessed from the internet .i have subdomain like radionis.zapto.org (192.168.0.2) registered at no-ip.org.now what IP i have to introduce there to make my server accessible
View 2 Replies View RelatedI have been using a laptop to stream videos through my xbox for over 2years until recently. I setup a wireless network in the house to do this. All was fine until 3 days ago.I use a Dell Inspiron 1545 with Windows 7. I have a Dell Wireless 1397 Minicard, a cisco router (model #2425). Since my laptop was infected by Malware, my network has not worked since. I downloaded Malwarebytes Anti Malware to get rid of it and it appeared to work. I got internet access back. However, I still cannot connect to my network (visible in the Available Network list as normal) or stream any media.Windows Media Centre also has stopped opening and gives me the small box saying 'windows is checking for a solution', then closes with nothing. I can however open WMC if I right click and 'run as administrator'?! I have disabled all other network adaptors, only the Dell minicad is enabled and also tried disabling and enabling this main one with no effect. All problems point to the fact that my laptop can no longer connect to the home network but I cant figure out why?!Another (possibly unrelated) problem is occuring at boot up where I get an error message saying 'Bluetooth Software License not found. [2]' - Again this never happened before the Malware infection.
View 1 Replies View RelatedCurrently I'm living in a dorm. The house has wireless network. But WEP encryption is used to secure it. I know this method is not safe. Also since there are many people are living in the house i don't want my computers be connected to this network.What i want to do is to setup my own network. I bought a NetGear DGND3300 router. I setup a WPA2 protected wireless network. I can connect all my devices to this network but naturally this way i have no Internet access.Is there a way to use Internet access of the house's router but still keep my local traffic not seen by anybody else
View 2 Replies View RelatedI'm a member of a club and we have just got BT Business Broadband with BT Business Hub 3. The club has one WiFi laptop which will occasionally access the BT Hub 3 using WiFi for internet use only. So essentially we have no network as such, just the BT Hub and a laptop.I would like to allow some club members to have internet access (WPA2 password), but without allowing access to the club laptop in any wayAs I said previously, the club laptop will only be active occasionally, so actual exposure is limited, but ideally I would like for the club laptop to be invisible to others when it is connected. I would also like each members equipment to be hidden from each other, so nobody can access each others data etc.. Can I achieve this simply? If so, do I need extra equipment?
I do have some donated equipment available: Netgear WAG102 Wireless Access Point, D-Link DSL-2640R Broadband Wireless G ADSL2+ Router and US Robotics 9106 SureConnect ADSL Wireless Gateway. Could I use any or all of these?I know this donated equipment is only Wireless G, but speed for the members is not important as they will only use internet access for emails and occasional google searches etc.I've tested the WAG102 at home, by plugging it into a LAN port of my BT HomeHub3 and giving it a different SSID, which works OK, but I can still see the other equipment connected wirelessly to my BT HomeHub3, although I cannot access my home laptop etc. because they are password protected.
Orange sent me a replacement Netgear DNG1000 and from the moment I had it there was issues, if N mode was enabled and I had to set it to B/G only for it to have a stable connection, not a problem as I only use it for the internet. The range on it was roughly the same as the livebox. For a few weeks it worked fine until recently it started to go insane, on the main computer the wifi works most of the time with 80%-95% signal strength, and then every now and then it will suddenly lose communication with the router but act as if it was connected for 5-10 minutes, signal strength is still at about 90% yet I can't access the router or the internet. Wifi works fine at full speed on the stairs, drops to a few bytes per second on the landing and then increases back up to full speed in the room next to it. In the one bedroom the wifi works up until the door where it instantly drops from full speed to a few bytes a second. This drop off point is only a few cms, as in full speed at one place, move it back a few cm and it slows down loads, but I still get 4-5 bars on windows and -50 RSSI on inSSIDer, about 94% strength and a link quality which tends to fluctuate. What could be causing this, specifically the weird instant deadzones and randomly not responding.
View 1 Replies View RelatedI would like to have the ability to turn off the internet access to my teens computers without effecting myself. I have parental controls on my computer which work great, but this does not work to the other computers that are able to connect wirelessly. I have a router but I am not sure how to access it.
View 3 Replies View RelatedI am running a VPN server on my desktop at home, with all the default settings, and i checked the box that allows clients to connect over the internet. this is win7 x64 computer. I opened up port 1723 with PPTP protocol on my E4200 router.On the client i am running win7 x64 as well. I am able to connect to the vpn, from another internet connection, but there is no local network acess. It says the status is No Internet Access. and the IP that is assigned is the 169.x.x.x one that windows defaults when it doesnt find a dhcp server.How can i get the client to connect with full local network access. Right now being connected to the vpn, it means nothing, i have no access other than being "connected".
View 1 Replies View Relatedi'm having an issue with a computer on my home network (Windows XP Professional SP3, latest updates) where i can't access the Internet or even the router on my home network (which it is part of).if i look at the network connection (wired) under control panel it shows as connected, and it's set with a static IP address (always has been), so nothing looks out of the ordinary there, yet if i try opening Internet Explorer i just get the "page cannot be displayed" page, and i can't even ping my own router- request times out.I've tried connecting a wireless adapter that i use on my laptop every day.. it connects to the wireless network no problem, but still the same results with IE and pinging the router.
View 4 Replies View RelatedI am experiencing problems trying to access my routers HTTP-type configuration. I have a Billion 400G router. The address to access the router was always http://10.0.0.2 and that has always worked. A dialog box would appear asking for a username and password. Now it doesn't even reach that screen. It says that the connection timed out. I've tried Firefox/Chrome/IE10. To no avail. My system: Windows 8 build 9500. Also something weird. When I type in this Microsoft thing comes up with IIS 8.
View 2 Replies View RelatedIt is a Satelite 733. Have pinged without any response however the wifi or hardwire will show connected to the local net.I have four other units surfing the web fine and wifi picks up ok except for one unit that my neighbor need will not connect no matter what. Have updated all the drivers, uninstalled and re-installed devices, reset ip, dumped the dns several times, etc.So here is the ipconfig stuff....ignore the cable connect I only have the wifi on at the moment. I have stared at this to the point where I know naathing .Is the tunnel adaptor the indication that the card is out? Oh and I tried taking out IPV 4 on both channels and nothing so I left one with 4 on and the other with it off just as something else to try. [code]
View 2 Replies View RelatedThe problem that I am facing is while accessing internet.I have replaced the LAN card also. It sends request but receives nothing. The cable line is also working fine
View 5 Replies View Related1. ADSL Wi-Fi router provided by my ISP. This is the primary router for my network which is connected to the internet. Router IP: 192.168.1.1 (DHCP enabled) 2. TP-Link wireless router which is connected to the primary router through its LAN port (not WAN) with its DHCP turned off. So I'm using this router ONLY to extend the network to another area. This is a 3G enabled router. Router IP: 192.168.1.2There are two different wireless SSIDs but basically only ONE network (all the PCs connected through any of the two routers are on the samesubnet and have same IP range i.e. 192.168.1.x). I want to use the 3G internet connection through the secondary router when the ADSL connection is down. Whenever the ADSL connection is down, I would just connect the 3G-USB to the secondary router, all the computers on the network should connect to the internet while skipping their route through the primary router WITHOUT CHANGING ANY SETTINGS. Is it possible? Do I need to modify the routing tables? Or is it
View 4 Replies View RelatedI am trying to set up a PPTP VPN connection which also provides internet access. I have the following configuration. The router named "Router1" connects 2 computers PC1 and PC2 on the LAN side with a network address of 192.168.1.0/24. It is a PPTP server and a DHCP server. It gives IP addresses to PC1 and PC2. It has a static address of 192.169.1.2 on the LAN side and a static address of 10.2.9.1 on the WAN Side. PC3 has a static address of 10.2.9.2 and is connected to the WAN port of Router1. "Router2" is connected to the LAN side of Router1 and it has a static IP of 192.168.1.1. Router2 is connected to the internet and provides internet connection to PC1 and PC2. PC1 and PC2 connects fine to the internet and can see each other. However, PC3 cannot connect to the internet even though it is connected to Router1 by PPTP VPN connection. PC3 can see PC1, PC2, Router1 and Router2 but it cannot connect to the internet because Router1 does not give it the default gateway(192.168.1.1) to connect it.
When PC3 connects via PPTP, It receives a correct IP address(10.2.9.3), correct DNS addresses but the ip4 default gateway field is left blank, and the DHCP option is not enabled on connection properties of PC3. Router1 is a DD-WRT firmware router (DLink Dir 400) and has PPTP server enabled as a service. How do I get Router 1 to give PC3 a default gateway IP? And how do I forward all outgoing packets from Router 1 to Router 2? I do not need portforwarding for some ports, I need full access to the internet from PC3 though the PPTP connection via Router2
I'm setting up a small network (one server, two clients) to create photo sales kiosks at an upcoming outdoor event. I will need internet access for processing credit card payments but there won't be any wi-fi or ethernet internet access on the site so I'll need to utilize my iPhone's 3G connection. I recently installed "MyWi" app which can tether the 3G and even create a personal wi-fi hotspot but unfortunately it only works in ad-hoc mode, not infrastructure.So far, the wired LAN is working great on my three Macbooks, using a Linksys (DD-WRT) router. Also, the wi-fi hotspot is working great to provide internet to all the computers. The problem, of course, is that I can't have both connected at the same time or else everything breaks. I've tried doing an iPhone-USB-Macbook tether and then sharing the connection via ethernet but the internet doesn't get through the router (because I don't have a clue of how to configure the router for this). I've also tried setting my router (DD-WRT) to do a client-bridge of the iPhone ad-hoc wi-fi, but again, it's way over my head and didn't work.
View 2 Replies View RelatedWas told by a HP technician that I could setup a .wireless home network for the purpose of having my iPad and iPhone 4 connect to my D100 HP printer. Installed the disc that came with my router and can't get passed the point that requires a password. All my devices recognize the router but everything requires a password which I am able to provide. Can this router be setup without having Internet access if so then how?
View 3 Replies View RelatedI just bought a Netgear Router WNR 2000 v3 and installed it. I got inside the router and could set up a Network Name and security key. However, I can not access the internet when I chose a security password using WPA 2, WPA-PSK + WPA 2 PSK, or WPA/WPA 2. It only accesses the internet when I chose None.( no secured ).At this time, my network is unsecured because there isn't way I can access the internet when I create a security key using the 3 options the router offers.
Note : I have tried the 3 security options creating a key number and my computer connect to the wireless network but don't access the internet. It only access the internet when I select None ( no secured )
i just got the Hawking HW2R1 and first i went through the setup as instructed but after all was done i tried connecting to the device from my computer. I was able to connect to the device but I didn't have any internet access (there was the little exclamation point next to the network icon). I know this is not due to internet problems with my router because my router (a Linksys befw11s4) has perfect internet connection. After this i called customer support. After an hour of talking to the person and going through many processes he says that we have tried all options available and told me about returning it.
View 1 Replies View RelatedI have ADSL modem in my workplace that is connected to a switch and other workplace computers are connected to this switch so the ADSL internet is shared in LAN network.(in each of computer I set default Gateway to ip of modem .....)I want to dial my workplace from home and then use of workplace internet or connect to workplace LAN.(such as VPN or Port Forwarding or I don't know...)
View 11 Replies View RelatedI have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies View RelatedI currently have a BT Home Hub 3 router and an Ubiquiti Power AP N.What I am trying to do is use the Ubiquiti access point as the main device for all connections in my house (ethernet and wireless) so that I can use the QoS settings etc. I basically want the Home Hub router to play as little role as possible in the network except for providing the ADSL internet connection.I know I need to enable DHCP on the access point but everytime I do so the devices connected to the access point lose internet connection.(BTW I have an ethernet cable connected from one of the routers LAN ports into the access point's WAN port)
View 2 Replies View RelatedI have a laptop that I take to work, and would like to set things up to use my home internet connection from elsewhere. I don't have another computer to function as a server for me at home, so would like to do it so that my router alone provides this access (log into it from the internet anywhere and use my internet as if I am using it from home). How would I go about doing this? Would it require installing new firmware?
View 1 Replies View RelatedI have bought a new laptop and added it to my home network , two pc's and two laptops all running win 7. I share all drives on all machines. I know this is not very professional but it works for me.From the new laptop I can see all the network and see all the different drive folders but can only access the user folder on any PC from the new laptop. Also I can see the drives on the new laptop but only access the new laptops user folder from any other PC. I have checked this through a LAN cable and wireless with no difference.As the other PC's can see each other as normal I can only think there's a problem with the set up in the new laptop. I also note when I first try and access any other pc from the new laptop I am asked a domain name and password , I can put anything in these boxes and get to see the network but as I said above only access the user folders. I do have password access turned of.
View 7 Replies View RelatedI was able to access my website jetbaby.com just fine before I changed the cPanel password. Now I cannot even load the site or load the cPanel login page here: jetbaby.com:2082 All I did was change the cPanel password. When I use another computer that is NOT on my network, I can connect to the site fine. I'm assuming that my network is blocking it for some reason after the cPanel password change. I tried the IP address in the address bar as well (still no go). Cannot "ping" the IP address either. I reset my modem and router as well. Cleared cache in browsers as well. I also disabled firewall and anti-virus for testing.
View 2 Replies View RelatedI split my network into 2 to make it more accessible during peak time and to minimize internet traffic. However by doing this only the first network can access our Network Access Storage, the other network can access it because the two are separated by different router and switch also the supervisor need to see both network at the same time for monitoring purposes..
View 6 Replies View RelatedActually i have a small network of 4 and 5 computers. i am sharing internet via lan not ICS.there are some computer showing me in my network places coz i am using windows 7 and the other computers have same window. i can ping their computers by name and by ip add, which is assigned by DHCP. i can see thir MAC address. can i access their computer i mean their data or something else. i don't know that this is the right place to share such information or not.
View 14 Replies View RelatedThree PC's all Win 7. Networking/Homegroup problem. In Network RV711 can see and access RC710 & Akoya. RC710 can see and access RV711 & Akoya. Akoya can see and access RV711. Akoya can see RV711 but not access RC710. Under Network Akoya can see RC710 but “You do not have permission to access...
In Homegroup. RV711 can see and access RC710 & Akoya. RC710 can see and access RV711 & Akoya. Akoya can see and access RV711. Akoya can see RC710 but not access RC710. Under Homegroup No other homegroup computers are available. In Homegroup the identical password is displayed on each PC. The Akoya is wired, the others are wireless. Summing up the Akoya cannot access the RC710.
I am using TP-Link TL-WR740N.Now I have a problem. In side my LAN I have four different PCs listening as Telnet Server at port 23. I want to create a telnet session over Internet with one of my PCs at a time.How should I do this? I mean what IP and Port number I should use to connect to my desired PC since all of my PCs are showing same public IP and that is of my router's IP.
View 7 Replies View Relatedmy home has a wireless network, and I can get internet (wirelessly) on my PC perfectly. What I was wondering is if it would be possible for me to hook up an ethernet cable to the RJ port on my PC, and connect my PS3 to it to give me a wired internet connection on the PS3.
View 14 Replies View Related