We have a 4402 wlc setup for guest network access. We are using the local net users to provide access to our guests. We have an issue where if a user signs in through the web, sometimes but not always, they are then forced to keep signing back in almost every 30-60 seconds.
View 8 RepliesThere is one guest interface, one guest WLAN. The WLAN is set with a DHCP override address of the guest interface. But it no longer allows this as I found out. Anyway, I can get the client to now receive an address from the internal pool on the WLC, but it will not route to the authentication page. I noticed that the WLC excludes the clients attempting to connect on the guest WLAN due to failed 802.1x authentication! the WLC never even gave me the chance to authenticate using an account created either through the lobby ambassador or creating one directly on the controller.
View 3 Replies View RelatedI have been trying to create a Guest WLan on my 4402 WLC system and have found several confilcting documents explaining the procedure. During this process I have notices that although the current corp wireless works, there was never a virtual interface created for it. Instead it uses the same Wlan/Vlan as the ap manager and managemnt interfaces. Could this by why I cant seem to get the Guest access working? or is this not a problem after all since the wireless does work.
View 1 Replies View RelatedI have this guest wlan working with web authentication, as you may know in order to get authenticated you must have an IP address first then have a valid username and password. The problem is that if you don't have valid credentials you keep the IP address anyways.I'd like to know if there is a way to release the IPs that are not being used? The WLC is the DHCP server for this network.
-WLC4402
-6.0.202.0
I am trying to setup a Wireless Network on my WLC that is totaly independent of our internal LAN. Port1 is designated at the .14.0 network and Port2 is the .18.0 network. The 14 network (Port1) will be the guest and 18 network (Port2) the internal wireless.
The issue i am having is nothing is routing to Port1. I have the Guest Wireless set to get DHCP from the WLC and i can get an address but i cant get internet access. I tried configuring a Network Route but it will only let me set the service port as the Gateway and not the IP for Port1.
I am running software version 5.1.151.0 and using this guide as it is the only one i can find. [URL]
Here is a screen shot of my Interface config.
Our Guest access system seems to be having problems with DHCP. It seems to take a while to deliver an IP address making the client device show the "limited or no connectivity" message, which of course makes the users complain. On one occassion I have seen my own client eventually picking up an address even after the limited connectivity message appeared. On another I saw the debug showing "Dhcp request for autoconfig address", which I suspect is a symptom of the problem.
Our Anchor Controller is the DHCP server and is a 4402 running 7.0.98.0 - I've attached some DHCP packet debug.
We have two WLC 4402 WLC in active-active mode in our setup. The issue we see is that a user/laptop gets connected and gets the ip address but there will be no network access. We see a yellow exclamation sign at this time in network icon in tray and we can not ping gateway at this point. We have run debugs at this time for the machine and we could see that was in "RUN" state its only that the machine can not access network.
View 11 Replies View RelatedWe currently have all of our foreign AP controllers on software version 7.0.116. This consists of a mixture of 4400 and 5508 WLC's. Our guest anchor is a 4402 on version 7.0.116. We are replacing the guest anchor with a 5508. We are also upgrading our 5508 wireless controllers to version 7.2 to support the 3600 series AP's. My question is what is the recommeded code that the anchor controller should be on? Should it also be upgraded to 7.2? If we upgrade the anchor controller to version 7.2, will this affect anchoring to 4400 series foreign controllers still on7.0.116?
View 9 Replies View RelatedIs it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies View RelatedI would like to know if exists some configuration using a WLC 4402 that deny network acces to smartphones but not to netbooks and laptops.
View 1 Replies View RelatedI have two Cisco WAP4410N access points. Both has Regular and Guest SSIDs, with same configurations, except "Wireless Isolation" on Guest SSID is enabled. Problem is Guest SSIDs are not visible on devices
Access points are working on different chanles, firmware Version: 2.0.1.0.
I'm a member of a club and we have just got BT Business Broadband with BT Business Hub 3. The club has one WiFi laptop which will occasionally access the BT Hub 3 using WiFi for internet use only. So essentially we have no network as such, just the BT Hub and a laptop.I would like to allow some club members to have internet access (WPA2 password), but without allowing access to the club laptop in any wayAs I said previously, the club laptop will only be active occasionally, so actual exposure is limited, but ideally I would like for the club laptop to be invisible to others when it is connected. I would also like each members equipment to be hidden from each other, so nobody can access each others data etc.. Can I achieve this simply? If so, do I need extra equipment?
I do have some donated equipment available: Netgear WAG102 Wireless Access Point, D-Link DSL-2640R Broadband Wireless G ADSL2+ Router and US Robotics 9106 SureConnect ADSL Wireless Gateway. Could I use any or all of these?I know this donated equipment is only Wireless G, but speed for the members is not important as they will only use internet access for emails and occasional google searches etc.I've tested the WAG102 at home, by plugging it into a LAN port of my BT HomeHub3 and giving it a different SSID, which works OK, but I can still see the other equipment connected wirelessly to my BT HomeHub3, although I cannot access my home laptop etc. because they are password protected.
I have created a new sub-interface on our ASA 5520 for guest internet access.
My goal is to allow access to a few specific services hanging off some dmz interfaces on the same firewall and full unrestricted access to the internet only. Everything else should be out of bounds.
The order of the rules I plan to setup on the guest interface inbound are:
#1. <rules to allow access to specific services in the dmz>
#2. <block any ip access to the entire private network ip address space>
#3. <permit ip any any>
#1. These rules will give access to the guest user to services located in the dmz
#2. This rule will block all access to any services in the private ip address space (thus blocking access to all internal services)
#3. This rule is to allow access to any other services i.e. the internet.
Is this the best way to achieve my goal in the most secure way or is there a better way? i.e. is there a way to force the traffic by default to only go out the outside interface unless there is a specific rule allowing it go elsewhere?
(Of course Dynamic PAT will also be configured for traffic coming from the guest interface to the outside interface.)
We have the RV180W router and the WAP321 access point in our business. We want to broadcast two SSIDs from both locations: the office SSID, which shares routing to LAN traffic, and a guest SSID.The office computers are attached via ethernet to a switch off of LAN port 1 on the router. The AP is attached to LAN port 2 on the router.On the router, the office SSID and the LAN are members of VLAN 1. The guest network is a member of VLAN 2. From the router, everything works just fine.On the WAP, the staff SSID works fine, but the guest SSID has no internet. Both the office and guest networks get DHCP successfully from the router.Our VLAN membership table in the router and WAP are attached, as well as other configuration details.Why would we not be getting internet on the guest ID only on the WAP?
View 8 Replies View RelatedI need to know how WLC can support ISE guest management in wireless mode. Tested and confirm by Cisco SE, Knowing that WLC currently does not support dynamic VLAN authorization for central web authentication. This limitation will be addressed in WLC 7.2 when MAB and CWA support is added to the code. On the other hand, DACLs on the other hand works and we can use that to restrict access of this guest traffic.Can ISE support on WLC LWA guest access provision? This able to view guest user login and show at ISE monitoring.
View 1 Replies View RelatedI got a problem with my netgear WNDR3400V2.As u see in this picture the box allow guest to access my local network is greyed out.I made the router an access point and have no clue how to make it normal again.
View 2 Replies View RelatedI have the syntax correct and thought process down right on a solution to allowing guest wireless users access to an internal webserver. (DMZ discussion aside)
We have an ASA5510 with interfaces setup as:
outside - 65.x.x.x address
inside - 172.20.1.2
guest_inet - 10.2.1.1
Internally clients resolve our website to 192.168.40.40 and that part works as it should. Clients outside of our network resolve our website to the correct external address (lets just call it 1.1.1.1). We have a NAT statement static (inside, outside) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 and an ACL to permit tcp any host 1.1.1.1 eq www
Clients on our guest_int use an external DNS server and hence resolve our website to 1.1.1.1. However it seems traffic goes out and back in our outside interface and this connection never occurs.
What I'm wondering is the correct NAT statement / ACL to add that would allow our internal clients on the 10.2.1.x network to access our internal website. Would that be: static (inside,guest_inet) 1.1.1.1 192.168.40.40 netmask 255.255.255.255 ? Since there is already an ACL permitting port 80 traffic to 1.1.1.1 we should be taken care of on the ACL side of things, right?
We have an RV042 as main router.We have a netgear WNR2000v2 as WIFI router.We would like to offer our drop-in customers an internet access. But without letting them into our network.
View 1 Replies View RelatedAny problems with the guest network on the ea4500 with the cloud firmware? I am losing guest clients after about 24 hours and the re-authentication fails. you enter the guest password and nothing happens until you reboot the router.
View 2 Replies View RelatedI have setup an aironet 1262 with my ASA 5512 and configured it as an access point. I would like to add an additonal network to the ap for guests to use but I would like to segregate the traffic and only allow it to the internet. I am not sure how to start this and go about setting the routes, security and address scope.
View 1 Replies View RelatedI've got two EA4500 routers connected via Ethernet. The primary router has DHCP enabled and the secondary has it disabled. IP address of primary is 192.168.1.1 and the secondary is 192.168.1.2.
I have set up guest access on both routers however only the primary router allows users to connect. When out of range of the primary router but in range of the secondary router the network is visible but when you try to connect to it, it only gives limited or no connectivity message and can't connect to the internet.
Is it possible for the guest network access to follow the same pattern as the secure network, i.e. the same network throughout the house?
We have a Cisco wireless infrastructure in place that includes a guest network with its own subnet that is a sub interface of the inside interface on our ASA 5520. There are no routes for it to be allowed access to the internal subnets. So it can only access the internet. This is primarily used by the public, but we have several non employee personnel that we only want to give internet access and force them to access the internal network through our clientless SSL vpn portal or through other internet facing internal resources such as webmail.I have done packet traces from within the ASA and the break appears to be there is no ACL allowing the traffic back into the network once the web resource replies to the request and the traffic is attempting to come back into the network from the web resource. Is that as clear as mud?
I know that this has to be a common problem and a way around this is to allow the guest wireless network access to the internal network but only for the select resources that they require. And that this can be done seemlessly by network specific routes and or alternate DNS entries, but I would like to keep this simple and just allow them to access the web resource, webmail and VPN, from the guest wireless using internet DNS servers without route trickery.
I have a cisco WLC 4402, i have a problem with people trying to log into wlc 4402 GUI console with wrong pass. Are there any ways that I can allow certain IP to go to or see the log in page of WLC?
View 5 Replies View RelatedWe have a WLC 4402, with interface Management, AP-Manager, and only the ap-manager interface is enabled for dynamic AP Management, how can i enable the dynamic AP Management for management interface also. Because i couldn't access WLC from via wireless, only able to access it via wired.
View 15 Replies View RelatedI have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
We are expanding our wireless infrastructure by adding further access points AIR-AP1242AG-E-K9.We use four WLC 4402 running version 6.0.188.0 as a fail over pair.What is the maximum limit the WLC can handle ?What is the recommended limit one WLC can handle ?We can divide the load on the controllers but in case of a failover one WLC will manage all access points.
View 4 Replies View RelatedI need Some information for Connecting my New Access point ( Cisco AIRLAP 1242AG) with WLC(4402) ControllerIn our network set up we have two WLC(4402) we needs to Connect this New Accesspoint To one of our WLC,My Access point is brand New. I need to Know what all i have to do inorder to connect this AP to the controller (from Acesspoint perspective & WLC perspective),I need to Know what I need to do in AP to connect to the Controller,Do i need to Assign Static IP Address forAP or after connecting to the switch it automatically gets ip from DHCP and regsiter with controller??
View 38 Replies View RelatedI have a 4402 and recently I have not been able to access the device via the service-port interface. The service-port has an IP Address and it is connected to an access port in the Vlan which I am coming from, however it cannot even ping it's gateway, which as mentioned is within the same network. When I am at the console of the controller I can ping the service-port interface IP that I have assigned, just nothing else.
View 4 Replies View RelatedI am working in an environment with 6 4402 all running 6.0.119.4 code and WCS 6.0.196.0. I keep getting an alert from WCS that the controllers cannot be reached "Controller '10.x.x.x' is unreachable. - Controller Name: 'Name'"
Now when I go to access the WLC through HTTPS I have no access at all but controller still responds to ICMP, HTTP, Telnet, SSH. I know I should have HTTP and Telnet disabled but since HTTPS keeps failing I would have no way to get into the controller. Is this a known issue in the 6.0.199.4 code? should I consider upgrading? The only fix I have found to work is to disable HTTPS reboot controller enable HTTPS and reboot again.
Does the N750 (F9K1103V1) support Guest Access while in Access Point mode? It will not provide an IP address when a guest attempts to connect.
View 20 Replies View RelatedI have an n600 ( F9K1102 v1 , firmware 1.00.09 ). My ISP provides my main router for my network, but I want to use the N600 as an access point, I have activated the "Use as Access Point" feature.Is it possible to still utilize the Guest Access feature in this case?
View 1 Replies View Relatedneed an access point configured in the user minimum because I was looking and some had up to 49 LAP connections at the same time. I have a WLC 4402 VERSION 7.0.98
View 1 Replies View RelatedWe have WLC 4402 and LWAP 1510In access control list menu, all needed rule added and the last rule deny any to any We use Ethernet bridging on LWAP and some clients connect with wire network that associated with Ethernet bridge LWAP, Now when deny rule applied the client that connect with wired network couldn't established VPN connection or another service to the routing and remote server, I create rule that permit any to routing and remote server.
View 1 Replies View Related