Cisco Wireless :: 4402 - Guest Access No Longer Working
Aug 10, 2011
There is one guest interface, one guest WLAN. The WLAN is set with a DHCP override address of the guest interface. But it no longer allows this as I found out. Anyway, I can get the client to now receive an address from the internal pool on the WLC, but it will not route to the authentication page. I noticed that the WLC excludes the clients attempting to connect on the guest WLAN due to failed 802.1x authentication! the WLC never even gave me the chance to authenticate using an account created either through the lobby ambassador or creating one directly on the controller.
View 3 Replies
ADVERTISEMENT
Nov 29, 2011
I have been trying to create a Guest WLan on my 4402 WLC system and have found several confilcting documents explaining the procedure. During this process I have notices that although the current corp wireless works, there was never a virtual interface created for it. Instead it uses the same Wlan/Vlan as the ap manager and managemnt interfaces. Could this by why I cant seem to get the Guest access working? or is this not a problem after all since the wireless does work.
View 1 Replies
View Related
Mar 23, 2011
We have a 4402 wlc setup for guest network access. We are using the local net users to provide access to our guests. We have an issue where if a user signs in through the web, sometimes but not always, they are then forced to keep signing back in almost every 30-60 seconds.
View 8 Replies
View Related
Jul 24, 2012
I am trying to setup a Wireless Network on my WLC that is totaly independent of our internal LAN. Port1 is designated at the .14.0 network and Port2 is the .18.0 network. The 14 network (Port1) will be the guest and 18 network (Port2) the internal wireless.
The issue i am having is nothing is routing to Port1. I have the Guest Wireless set to get DHCP from the WLC and i can get an address but i cant get internet access. I tried configuring a Network Route but it will only let me set the service port as the Gateway and not the IP for Port1.
I am running software version 5.1.151.0 and using this guide as it is the only one i can find. [URL]
Here is a screen shot of my Interface config.
View 7 Replies
View Related
Nov 1, 2011
I did not use the CD to set up, and instead set this router up manually. We are using this router right now as a hotspot only.. and all is good. I can see both new networks and the WIFI laptops are talking no problem. Only issue I have is that guest access is not working - by that I mean it can't get out on the internet. I can see it as available and connect to it. Guest access and SSID broadcast are both enabled obviously.
View 8 Replies
View Related
Aug 26, 2012
I have this guest wlan working with web authentication, as you may know in order to get authenticated you must have an IP address first then have a valid username and password. The problem is that if you don't have valid credentials you keep the IP address anyways.I'd like to know if there is a way to release the IPs that are not being used? The WLC is the DHCP server for this network.
-WLC4402
-6.0.202.0
View 6 Replies
View Related
Jul 8, 2011
We have the E3000 Router and the guest internet access DOES NOT work. We occasionally repair other people's PC's and I seriously do not want to allow access to our home network. Recently, we are trying to access through guest, on a Win 7 Dell Notebook. It takes the passcode but no internet connection.
View 1 Replies
View Related
Nov 6, 2012
We currently have all of our foreign AP controllers on software version 7.0.116. This consists of a mixture of 4400 and 5508 WLC's. Our guest anchor is a 4402 on version 7.0.116. We are replacing the guest anchor with a 5508. We are also upgrading our 5508 wireless controllers to version 7.2 to support the 3600 series AP's. My question is what is the recommeded code that the anchor controller should be on? Should it also be upgraded to 7.2? If we upgrade the anchor controller to version 7.2, will this affect anchoring to 4400 series foreign controllers still on7.0.116?
View 9 Replies
View Related
Aug 18, 2011
Is it possible to allow certain websites to bypass the web authentication pages, so that they do not need to authenticate to get to our own website, but do have to if they wish to go anywhere else?Looking at a 5508 model at the moment
View 4 Replies
View Related
Feb 3, 2011
Our Guest access system seems to be having problems with DHCP. It seems to take a while to deliver an IP address making the client device show the "limited or no connectivity" message, which of course makes the users complain. On one occassion I have seen my own client eventually picking up an address even after the limited connectivity message appeared. On another I saw the debug showing "Dhcp request for autoconfig address", which I suspect is a symptom of the problem.
Our Anchor Controller is the DHCP server and is a 4402 running 7.0.98.0 - I've attached some DHCP packet debug.
View 6 Replies
View Related
Apr 23, 2011
My Internet surveillance stopped working
View 1 Replies
View Related
Jul 18, 2012
I have WLC 4402 working with AIR-AP1131AG-E-K9. Need to buy another pair. I looked to the side air-ap1041n-e-k9. Tell me whether or not the compatibility of the controller and the AP1041n? One more question. When buying in 1131 is still in the box and power cord to the point. The new 1041, the purchase comes with the point of the power cord?
View 13 Replies
View Related
Apr 12, 2012
I have an issue with AP Fallback not working with two Cisco 4402-50 WLC's. Here is the senerio:
Site 1 has a 4402 (WLC01) running software 7.0.220.0 with 48 associated access points. AP Fallback is enabled in Controller > General and all 48 AP's are set to Critical failover with WLC01 being the primary controller and WLC02 (at site 2) being the secondary.
Site 2 is the location of WLC02 which is also running software 7.0.220.0 but has 0 ap's associated and also had AP Fallback set to enabled.
Your typical active/passive setup
The problem is when WLC01 goes down all of the AP's fail over to WLC02, however when the connection is restored to WLC01 we have to manually reboot each access point in order for them to reassociate back to the primary controller. Isn't AP Fallback enabled suppose to allow the AP's to move back to the primary controller once connection is reestablished?
View 15 Replies
View Related
Oct 16, 2012
I have a Cisco Wlc 4402 , denon 3312 & AP 1142 all three devices are same subnet . But Airpaly not showing in Iphone. But if i put a Airport express in on these subnet then i find airplay option. How without Airport express i can enable airplay...
View 2 Replies
View Related
May 24, 2011
I've been using my AE1000 for about a month now with absolutely no problems. Yesterday it just stopped working, I removed it from the USB port and just about burned my fingers on the metal part that plugs into the USB port. BTW I am on Windows 7 64-bit.
Now it won't work. I've tried reinstalling the driver and the device just blinks in the "Devices and Printers" control panel. I removed it again and it was very hot to the touch after only being in the port for about a minute.
View 1 Replies
View Related
Dec 6, 2011
I've got 3 WLC 4402 controllers and the wireless is working perfectly except for 1 issue. We are trying to connect an apple tv, so we can stream picture, videos etc from ipads and Macbooks to a large display for media teaching.The setup works at home, but not at work.The apple TV is on the same network as the wireless apple devices, (we use a 10.6.4.x-10.6.5.254 range), both are dhcping the addresses (have tried fixing but that made no difference). I've enabled multicasting and igmp snooping and set the multicast address as 239.0.0.0 and it still doesn't work.
View 11 Replies
View Related
Nov 19, 2012
We need to add additional APs to working wireless mesh network (WLC 4402, 1520 series AP).
WLC 4402 supports 1550 series access points with firmware upgrade to 7.0.235.0 :
[URL]
Is AIR-CAP1552E-x-K9 with three external dual band antennas enough for 2-GHz b/g/n local access and 5-Ghz back haul?
Does 1552 Mesh AP work with 1522 Root AP?
View 1 Replies
View Related
Jun 15, 2011
My AE1000 has worked for about 2 weeks, but just stopped working. Have tried to reinstall but it won't recognize the adapter. I can't click the "next" button to continue the installation. I have chagned the USB ports and restarted the computer. But it still wont install. I have Windows Vista. I also have Norton, do I need to uninstall this?
View 1 Replies
View Related
Jun 24, 2012
I have a new Linksys E2100 that was working well with an old Verizon modem. Then recently that modem gave up the ghost and I was issued another one (Westel Model 6100G). I have no problems with internet connectivity when connecting directly from my harddrive to the Verizon modem. I am also not having trouble connecting to the Linksys routher as I am able to see my wireless connection with no problem. However, when I try to set up the connnection with the E2100 in the loop (yes, it's connected correctly) I no longer have internet access.
I tried de-installing and re-installing the Linksys software (thinking maybe there was some new configuration that would be auto-detected with a new set-up), but this didn't work. I suspect that if the problem is with my Linksys router and not with my Verizon modem that there might be something that could be done to reconfigure something manually but I do not know enough about connections and wireless systems to trust myself not to mess something up.
At this point I'm assuming it's a Linksys issue since I know that my Verizon modem can connect me to the internet, so works properly. Is there some known incompatibility with this Linksys model and the Westell 6100G modem?
View 2 Replies
View Related
Sep 28, 2011
I have had a WRT54G V3 router working successfully for a number of years now with a couple wireless PCs through a cable modem with Comcast as my ISP. All of a sudden yesterday, neither PC could access the internet. No changes had been made to the router.
I contacted Comcast and they of course had me hard-wire one of my PCs into the cable modem. That worked and I was able to access the internet. However, when I tried to put the router back in place (in either a wired or wireless fashion), I could not access the internet.
I've tried following the online Linksys troubleshooting document ion. The lights that should be lit on the router are lit. I can access the router setup web page which shows the settings still intact. I've tried going through the power sequencing to no avail. Comcast says my router is the culprit of my problem, but I don't know why it would all of a sudden stop working. My wireless printer still works so it detects a signal and my PC shows it's connected, but no internet access is possible.
What do I need to do? Are there any other diagnostic tools available? I'm out-of-warranty.
View 4 Replies
View Related
Feb 5, 2011
I was using desktop computer and got infamous blue screen of death Rebooted and everything was fine except could no longer could see LAN connection or connect to internet The desktop computer also has a wireless card that allows me to connect to router wirelessly but only get "connect with limited access" I have a cable connection through a router and tried connection dsl directly to ethernet and bypassing router but no change Router works for other laptops to connect wirelessly I can see both network adapters in the device manager and both say devices are working properly Here are the results of ipconfig /all:
Microsoft Windows [Version 6.0.6002]
Copyright (c) 2006 Microsoft Corporation. All rights reserved.
C:UsersCooper>cd c:
c:>ipconfig /all
Windows IP Configuration[code]......
View 5 Replies
View Related
Mar 11, 2013
We have two WLC 4402 WLC in active-active mode in our setup. The issue we see is that a user/laptop gets connected and gets the ip address but there will be no network access. We see a yellow exclamation sign at this time in network icon in tray and we can not ping gateway at this point. We have run debugs at this time for the machine and we could see that was in "RUN" state its only that the machine can not access network.
View 11 Replies
View Related
Nov 15, 2011
We have a WLC 4402, with interface Management, AP-Manager, and only the ap-manager interface is enabled for dynamic AP Management, how can i enable the dynamic AP Management for management interface also. Because i couldn't access WLC from via wireless, only able to access it via wired.
View 15 Replies
View Related
Jun 2, 2011
Last night on the xbox 360 i was suddenly experiencing alot of lag on other peoples voices. i took no notice of it and the next day i went on my laptop and alot of websites wouldn't load properly.i can go on google,obviously this and my hotmail(after having to wait a long time for the hotmail to load), but others such as ebay will not load. I cannot even access my router settings by typing in my ip address, instead i get a message saying the page cannot be found. also i was disconnected from xbox live with the internet to xbox live part not working. Obviously the first thing i done was turn the router off and back on but it hasn't made any difference.
OS Version: Microsoft Windows Vista Home Premium , Service Pack 2, 64 bit
Processor: Pentium(R) Dual-Core CPU T4200 @ 2.00GHz, Intel64 Family 6 Model 23 Stepping 10
Processor Count: 2
RAM: 4055 Mb
Graphics Card: Mobile Intel(R) 4 Series Express Chipset Family, 1804 Mb
Hard Drives: C: Total - 290204 MB, Free - 141170 MB; E: Total - 14999 MB, Free - 5644 MB;
Motherboard: Dell Inc., 0G848F, , .5MDJWJ1.CN7016697U05OT.
Antivirus: AVG Anti-Virus Free Edition 2011, Updated and Enabled
View 3 Replies
View Related
Jun 24, 2011
I cannot get the Guest Network feature to work.Even though Guest SSID is enabled, it does not show up on any devices attempting to connect. Manually connecting by entering the Guest SSID fails (not recognized). On devices with the primary 5 and 2.4 GHz configured they do see the third network but without SSID (unknown) and are also unable to connect to it manually using the SSID.I did not try this before 1.0.02. Have rebooted modem and verified all configs (multiple times). The network is live in an office and can't keep screwing with it or drastically changing its settings.
View 9 Replies
View Related
May 9, 2012
I have two SSIDs on an Autonomous Access Point, that goes to a 2960 switch, that connects to a L3 3560. I have a vlan for admin/private internal access that uses the native vlan (1) and guest vlan (50). I have configured both and I am trying to get both to go out the same Internet connection.
I cannot get the guest access to access the Internet. It looks like my computer will go, but it just comes up saying no Internet access.All interfaces are trunking this vlan properly. I can communicate from the laptop to the 3560 but I just can't get to the Internet.
View 10 Replies
View Related
Jun 13, 2012
I have a Cisco ASA 5510 (with an AnyConnect Mobile License enabled) I used to be able to connect to the VPN using the AnyConnect app for Android form the Google App store (the phone is a Samsung Galaxy S II LTE, if that matters). Like I said everything used to work fine until a few weeks ago, the only change I made to the router was giving it a different external IP address (I changed ISP), I'm pretty sure it worked after that. But now when I try to connect with my Android I get this error: "Clientless (browser) SSL VPN access is not allowed".
View 1 Replies
View Related
May 16, 2011
I am enabling our wireless controllers to use 802.1x authentication for our wireless clients. Both computer and user are provided with certificate from CA server.I have 9 APs and 2 controllers installed in my infrastucture, one of the controllers is working fine with setting specified above but the other one is not.Both has same configuration and both seems identical with same model and IOS.
View 3 Replies
View Related
Mar 27, 2011
I use the Windows7 Virutal WIFI when traveling abroad to give my Iphone an internet connection in my hotel.I've had zero issues until this week. The WIFI connection is still showing up on my iphone, but I no longer get internet access (I only get an IP and subnet on the iphone now, no router or DNS info). The issue began (coincidence or not) as my MagicJack downloaded and installed a software update. MagicJack support says they aren't the issue. I experimented with created an Ad-Hoc network...no change. I've removed and reinstalled the wireless card and driver. No change. I suspect some corruption with ICS, but haven't found any solutions online to fix it.
Microsoft Windows [Version 6.1.7601]
Copyright (c) 2009 Microsoft Corporation. All rights reserved.
C:ipconfig /all
Windows IP Configuration
Host Name . . . . . . . . . . . . : Richard-PC
Primary Dns Suffix . . . . . . . : MARCOGROUP.local
[code]....
View 1 Replies
View Related
Jun 29, 2011
I would like to know if exists some configuration using a WLC 4402 that deny network acces to smartphones but not to netbooks and laptops.
View 1 Replies
View Related
Nov 13, 2011
I have a WLC of 4402 and AP's of AIR-LAP1142N-E-K9 . Where am getting problem of that users are complaining that they cannot connect it some times and they used to get disconnected in between.
View 1 Replies
View Related
Feb 19, 2012
my Vizio TV (VF552XVT) can no longer find any wireless access points even after inputting SSID or IP information. Other wireless devices (my phone) are able to connect wirelessly. Everything was working fine until a power outage about 3 days ago.
View 2 Replies
View Related
Mar 20, 2012
I used Cisco connect to set up guest access with a secure password. Cisco Connect now indicates guess access is allowed and shows the password. However, when I actually try to connect to the guest network, it shows no security at all, and I can join the network without a password.
View 1 Replies
View Related
