Cisco Wireless :: AP Fallback Not Working With 4402?
Apr 12, 2012
I have an issue with AP Fallback not working with two Cisco 4402-50 WLC's. Here is the senerio:
Site 1 has a 4402 (WLC01) running software 7.0.220.0 with 48 associated access points. AP Fallback is enabled in Controller > General and all 48 AP's are set to Critical failover with WLC01 being the primary controller and WLC02 (at site 2) being the secondary.
Site 2 is the location of WLC02 which is also running software 7.0.220.0 but has 0 ap's associated and also had AP Fallback set to enabled.
Your typical active/passive setup
The problem is when WLC01 goes down all of the AP's fail over to WLC02, however when the connection is restored to WLC01 we have to manually reboot each access point in order for them to reassociate back to the primary controller. Isn't AP Fallback enabled suppose to allow the AP's to move back to the primary controller once connection is reestablished?
View 15 Replies
ADVERTISEMENT
Jul 18, 2012
I have WLC 4402 working with AIR-AP1131AG-E-K9. Need to buy another pair. I looked to the side air-ap1041n-e-k9. Tell me whether or not the compatibility of the controller and the AP1041n? One more question. When buying in 1131 is still in the box and power cord to the point. The new 1041, the purchase comes with the point of the power cord?
View 13 Replies
View Related
Oct 16, 2012
I have a Cisco Wlc 4402 , denon 3312 & AP 1142 all three devices are same subnet . But Airpaly not showing in Iphone. But if i put a Airport express in on these subnet then i find airplay option. How without Airport express i can enable airplay...
View 2 Replies
View Related
Dec 6, 2011
I've got 3 WLC 4402 controllers and the wireless is working perfectly except for 1 issue. We are trying to connect an apple tv, so we can stream picture, videos etc from ipads and Macbooks to a large display for media teaching.The setup works at home, but not at work.The apple TV is on the same network as the wireless apple devices, (we use a 10.6.4.x-10.6.5.254 range), both are dhcping the addresses (have tried fixing but that made no difference). I've enabled multicasting and igmp snooping and set the multicast address as 239.0.0.0 and it still doesn't work.
View 11 Replies
View Related
Aug 10, 2011
There is one guest interface, one guest WLAN. The WLAN is set with a DHCP override address of the guest interface. But it no longer allows this as I found out. Anyway, I can get the client to now receive an address from the internal pool on the WLC, but it will not route to the authentication page. I noticed that the WLC excludes the clients attempting to connect on the guest WLAN due to failed 802.1x authentication! the WLC never even gave me the chance to authenticate using an account created either through the lobby ambassador or creating one directly on the controller.
View 3 Replies
View Related
May 19, 2013
we are testing WLC v7.4 in our lab. The AP joins fine but when we try to move it to another WLC running 7.2 (simulating a fall-back plan if there are issues with the 7.4 code), it fails saying image not found.
View 4 Replies
View Related
Nov 29, 2011
I have been trying to create a Guest WLan on my 4402 WLC system and have found several confilcting documents explaining the procedure. During this process I have notices that although the current corp wireless works, there was never a virtual interface created for it. Instead it uses the same Wlan/Vlan as the ap manager and managemnt interfaces. Could this by why I cant seem to get the Guest access working? or is this not a problem after all since the wireless does work.
View 1 Replies
View Related
Nov 19, 2012
We need to add additional APs to working wireless mesh network (WLC 4402, 1520 series AP).
WLC 4402 supports 1550 series access points with firmware upgrade to 7.0.235.0 :
[URL]
Is AIR-CAP1552E-x-K9 with three external dual band antennas enough for 2-GHz b/g/n local access and 5-Ghz back haul?
Does 1552 Mesh AP work with 1522 Root AP?
View 1 Replies
View Related
Feb 14, 2013
I'm deploying a Cisco Mesh infrastructure using WLC 7.2 version and 1552 APs.
This Mesh APs will be connected in the Light Pole and the RAP will be connected to the SP Switch located in this same Pole.
The MAP will be powered using Pole source power and will be connected to the RAP over 5.8 Bach haul.
My Customer asks if is possible that in case of SP Switch lost the connectivity to the Backbone IP, the RAP can connected to another RAP and maintain the connectivity to the Backbone over the Air, like REPEATER FALLBACK mode in Autonomous version.
For that I thinking to change the role of the RAP APs to "MAP with UTP Cable", but I'm not sure that a MAP AP with CAPWAP tunnel over UTP Cable can provide a Down link Backhand to another MAPs. That is possible?
View 3 Replies
View Related
May 16, 2011
I am enabling our wireless controllers to use 802.1x authentication for our wireless clients. Both computer and user are provided with certificate from CA server.I have 9 APs and 2 controllers installed in my infrastucture, one of the controllers is working fine with setting specified above but the other one is not.Both has same configuration and both seems identical with same model and IOS.
View 3 Replies
View Related
Sep 6, 2011
I have a Cisco 886G i have configured a fallback mechanism. i did this with a sla track. You can see this in the config below. Bij the problem is that i can't get internet to work when connection is in fail over state. it fails over to Cllular0 and i can ping from router to the internet. that works fine but when i want to use the internet from one of the pc's is doesn't work. i traced it to nat. there seems to be that only one ip nat inside source .... when i change this one from dialer0 to cellular0 i have internet on the computers.how can i configure multiple ip nat inside source... rules or is there an other way to accomplished this?
View 1 Replies
View Related
Aug 17, 2011
I have ACS 5.1 configured to authenticate users based on Active Directory. I have configured wired 802.1x too, with machine authentication enabled on ACS.When I login with credentials that exist in AD, it works fine. Then I configured Windows Authentication to ask for credentials (popup window). But I experience network disconnection when I login with a local account even though I entered correct AD credentials.I want to do the following: for an account that exist on the machine being authenticated (non-AD account), ACS should check its local database and reply with authentication success if it finds it, so the user is granted network connectivity.I heard about Identity Sequence in ACS. But I still don't see the right configuration,
View 2 Replies
View Related
Oct 26, 2011
We have both ADSL2+ and Cable broadband and wish to have them both connected to and accessible on the same network, possibly linked by using the WiFi modem-routers or by adding redundant WiFi modem-routers in bridge mode.The object is to have a seamless each-way fall-back as both broadband feeds have been unreliable in the past, sometimes for weeks at a time and this has had a destructive influence on concurrent college, uni courses and various pocket-money commercial interests.The current situation is to have two separate wired networks running at 100/1000 with limited WiFi access for laptops and mobile device access.All clients would effectively be part of the same workgroup but with a possible future dmz to a small dynamic dns server for non-business convenience and test use. (HTML, PHP, MySQL website development exercises etc.)At present, there are no significant internal security issues within the firewalls provided by the existing modem-routers and there is no significant budget.
View 2 Replies
View Related
Feb 9, 2010
I know the way to configure the ASA to fallback to LOCAL authentication, if the Radius server is not available.
Now we would like to authenticate the local users, if the user is not found in the AD. Is this possible and how can I configure this with the new policies? I tested it with "dropping" when the user is not found in the AD, but then the Radius server will be marked as "dead" and the other AD users can't login for a given period. Maybe we can configure the dead time to 0, but this is not as nice it could be.
View 4 Replies
View Related
Nov 20, 2011
I have 2 4402 WLC's and am in the process of deploying 1042 APs out to sites. But The AP's wont recognize the WLC. I have configured the DNS for CAPWAP but still no dice. I have had to serial into each unit and give it a static IP and then I can see it on the WLC. Shoulsnt this be automatic?
View 21 Replies
View Related
Jul 29, 2010
Any explanation about this warning from the WLC4402 after the software upgrade to 7.0.96. version? this is the message: Warning: WLC has detected its IP add xx.xx.xx.xx being used by a machine with MAC add xx:xx:xx:xx.and the MAC add found is the the mac add of the dynamic interface of the WLC.
View 7 Replies
View Related
Jun 29, 2011
My WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
View 4 Replies
View Related
Jun 25, 2012
Can 3600 series model AP work with WLC 4402 with existing license, we purchased 25 LIC pack and still using only 15. Any recommended Part no on 3600 series with external Antenna
View 5 Replies
View Related
Jun 7, 2012
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
View 12 Replies
View Related
Jun 13, 2012
Error: AAA Authentication Failure for UserName:radiususername User Type: WLAN USER
I am using a window radius server. I have added my WLC 4402 as a radius client on my radius server.
I followed the instructions on the MS link : [URL]
I want to use my windows raduis authentication for WLC management login and Web-Auth for guest WLAN user login.
View 2 Replies
View Related
Feb 3, 2013
Our company has a customer with a Cisco 4402 WLC and a code version of 4.2.130.0 . The customer wants to upgrade the code to 7.0.230.0. Is there any flash size requirement when upgrading to 7.0.230.0? (upgrade train: 4.2.130.0 ----> 4.2.209.0 ----> 7.0.230.0), How can I find the flash size?
View 2 Replies
View Related
Feb 3, 2013
We got WLC 4402 running software 7.0.235 and would like to backup the configuration and restore on 5508. Is this doable? Do we need to be on the same version as WLC 4402. How to get cisco document to follow the steps if the above is doable,5508 is new with no setup.
View 6 Replies
View Related
Jan 16, 2012
I need to install one 5508 and a 4402 together to bring redundancy to a wireless environment.Can I do this?. What are the neccesary steps to perform this?, the idea behind this is to bring redundancy is the primary WLC falls for any reason.
View 4 Replies
View Related
Mar 7, 2011
I have two wlc 4402 to control 50 AP 1131. 2 WLC: wlc-01 and wlc-02, wlc-02 config as backup wlc in the same mobility group. Client authentication:EAP with Microsoft IAS/AD.All AP have joined wlc-01. Wireless client work well with wlc-01.For testing I config access point AP01 have primary wlc: wlc-01, secondary: wlc-02 If I change config of AP01 like this: primary wlc: wlc-02, secondary: wlc-01. Client is hard to connect to wlc-02 and it only connect when client set static ip ALL wlc run this softwar image: 7-0-98-0 Should I send wlc-02 to warranty service?
View 8 Replies
View Related
May 17, 2012
I do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
View 4 Replies
View Related
Jul 24, 2012
I am trying to setup a Wireless Network on my WLC that is totaly independent of our internal LAN. Port1 is designated at the .14.0 network and Port2 is the .18.0 network. The 14 network (Port1) will be the guest and 18 network (Port2) the internal wireless.
The issue i am having is nothing is routing to Port1. I have the Guest Wireless set to get DHCP from the WLC and i can get an address but i cant get internet access. I tried configuring a Network Route but it will only let me set the service port as the Gateway and not the IP for Port1.
I am running software version 5.1.151.0 and using this guide as it is the only one i can find. [URL]
Here is a screen shot of my Interface config.
View 7 Replies
View Related
Dec 18, 2011
We are attempting to use LDAP for web authentication on a WLC 4402.
[URL]
You are able to connect to the SSID and it reidrects you to the login page as it should. When you enter your username and password you get a message that "the username and password combination you have entered is invalid." Based on the following log it looks like the LDAP bind is the issue.
*LDAP DB Task 1: Dec 19 11:19:26.584: %AAA-3-LDAP_CONNECT_SERVER_FAILED: ldap_db.c:1038 Could not connect to LDAP server 1, reason: 1005 (LDAP bind failed).
We are able to test the following configuration with ldp.exe successfully,
Server: ***.***.***.***
Port Number: 389
Bind Username: CiscoBYOT
[Code].....
View 2 Replies
View Related
Jun 22, 2012
I tried to upgrade the cisco boorloader pf WLC 4402 from version 4 to 7.2. I updated ER.Aes FOR 7.2 (EARLY RELEASE.aes). It was updated perfectly and then I rebooted controller....now i can only see blank screen from connected console.I tried the flash of other lan controller but its not working because the issue is in the ROM as the boadloader file is in the ROM which is corrupted now i want the solution to upgrade the boatloader file inside the ROM.
View 1 Replies
View Related
Jun 12, 2012
My customer has a 4402-25-K9 and need a backup (failover) controller to avoid data transmision break when primary controller goes down.4402 are end of sale so I have a question can I use 5508 to get Controller Failover Protection with 4402 ?
View 3 Replies
View Related
Jun 6, 2012
We have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
View 3 Replies
View Related
Nov 7, 2011
I ##have a customer with WLC 4402 in use, running software version 7.0.98.0, and supporting 11 APs at present. The customer wants to enlarge the WLAN, which involves increasing the number of APs. I #####have purchased a new WLC5508, and have installed it onto the network alongside the 4402. the 5508 is running software version 7.0.116.0. Because the wireless network is critical to the user, we want to move the APs over to the new controller while the network is up and running, then remove the 4402.
However, when we set the 5508 as the master controller, or tell one of the APs to use the 5508 as its primary controller, the AP connects to the new controller, downloads the new software version, attempts to load it but reports an error with the unzipped file size of the software and fails to boot. formatting the flash on the AP, then disconnecting the 5508 from the network and rebooting the AP allows it to connect to the 4402, it downloads the older software and boots as normal. A new AP, if connected to the 5508 in a test scenario (ie no 4402) connects, downloads and boots perfectly.
I #have the upgrade software to allow the 4402 to be upgraded to 7.0.116.0, but I am concerned that, if this is installed, the existing APs will then fail to boot from the 4402 or the 5508.all APs are 3502s, running IOS version 12.04(23c)JA when connected to the 4402 and 12.04(23c)JA2 on the 5508.
View 7 Replies
View Related
Mar 11, 2013
We have two WLC 4402 WLC in active-active mode in our setup. The issue we see is that a user/laptop gets connected and gets the ip address but there will be no network access. We see a yellow exclamation sign at this time in network icon in tray and we can not ping gateway at this point. We have run debugs at this time for the machine and we could see that was in "RUN" state its only that the machine can not access network.
View 11 Replies
View Related
Mar 24, 2012
I 'm trying to upgrade WLC 4402 up from 5.1.151. After upgrade to 5.2 or higher https interface is inaccessible. If I use any other previous version, all is OK. Somewhere I found recomendation to open http before upgrade and use it at first. It works, but what to do next? To stay on http only?
View 1 Replies
View Related
