We got WLC 4402 running software 7.0.235 and would like to backup the configuration and restore on 5508. Is this doable? Do we need to be on the same version as WLC 4402. How to get cisco document to follow the steps if the above is doable,5508 is new with no setup.
View 6 Replies4402 Wireless LAN Controller running 7.0.116.0 versión. The equipment is working fine, but after a hard reset i lost date and time configuration.No other configuration is affected, only date and time. What can be the cause of this?
View 18 Replies View RelatedI have old ASA with 8.0 configuration that includes huge number of ACL, NAT , VPNs , we got a new ASA with 8.6 , and we are planning to move the configuration to the new box , I'm wondering what is the best approach to do this , I'm thinking of one of the following scenarios1- downgrade the new ASA to 8.3 , the apply the config , remove the identity nat commands and names then upgrade to 8.6 and after that reconfigure the NAT rules and object groups .2- convert the old config manually to 8.6 code including NAT , object-group ,ACL and apply it to the new ASA ( this is going to be huge task). What are the commands that I have to look at when I convert to 8.6 and will the VPN configuration be affected ?
View 5 Replies View RelatedHow to migrate the following config from a CSM to and ACE20 module.
Currently we have a CSM configured as below:- 452 Client and 453 Server sharing the same Public vlan.
We require outbound access from groups of internal individual servers to external addresses.
CSM config
module ContentSwitchingModule 8
vlan 452 client
ip address 10.206.135.252 255.255.252.0
[Code].....
I need to replace an existing ASA 5540 with a new ASA 5525X. I would like to pre-stage and configure the new box with the existing config, migrate license and export certificate files before swapping it with the old one during a change window. The new firewall will run 9.1 on deployment. Now the same 7.2(4) cannot just be copied over to 5525X running the minimum 8.6 version. There is a Web based tool available at [URL] according to Cisco documentation but the page does not load for me (Cisco intranet only tool ?). Is there another tool for automatic conversion ?
View 3 Replies View RelatedI'm trying to get all the templates and Maps I've created in WCS into our new NCS. The instructions say just run the export.bat file on WCS and then Migrate into NCS. I cannot find any export.bat file on version 7.0.220.0 of WCS. Is it only available in WCS version 7.0.164.3 ro 7.0.172.0? Do I have to use the export.bat file or can I just do a regular backup and restore?
View 7 Replies View Relatedi have a existing wireless network setup in my office existing wlc in 4402 and LAPs are 1130 & 1242 all are working fine but we are now planning to use new 5500 series controllers for the same access points,i want to ask that how i can done this job with very minore downtime and users disconnectivity + zero error results??
View 2 Replies View RelatedI am about to migrate WISM1 to WISM2, The image of WISM1 is 6.0.199.4 and the image of WISM2 is 7.2.111.3.
Do i need to upgrade WISM1 to 7.2.111.3 before i export the configuration and import it into WISM2? Or can i just export the configuration from WISM1 on 6.0.199.4 and import directly to WISM2 which is on 7.1.111.3?
I have a question to migrate a customer from a 2106 controller to a 2504 controller. Can I use the configuration file with both controllers having the same version?
Or is there another way not having to do it again manually? The old configuration is OK, only the hardware is end of sale.
I have a existing wireless setup of 4400 WLC with some AP's connected remotely,now i am migrating the whole setup to the new WLC 5500. All the AP has been registered to the new WLC 5500 except the remote location AP's.As there was no option of giving IP address in GUI of the controller in 4400 WLC, i have changed the controller name and restarted the AP, but even though it is going back to the old controller.
View 15 Replies View RelatedI just bought mw3 but when I try to start multiplayer the game direct me to this, [URL]. I don't know how to fix it, and my UPnP is enable
View 6 Replies View RelatedI have 2 4402 WLC's and am in the process of deploying 1042 APs out to sites. But The AP's wont recognize the WLC. I have configured the DNS for CAPWAP but still no dice. I have had to serial into each unit and give it a static IP and then I can see it on the WLC. Shoulsnt this be automatic?
View 21 Replies View RelatedAny explanation about this warning from the WLC4402 after the software upgrade to 7.0.96. version? this is the message: Warning: WLC has detected its IP add xx.xx.xx.xx being used by a machine with MAC add xx:xx:xx:xx.and the MAC add found is the the mac add of the dynamic interface of the WLC.
View 7 Replies View RelatedMy WLC running 6.0.182.0 suddenly could not accept more than 47 APs! Ihave a 1240 trying to join but failed with no obvious reason (no special errors in debugging).
I unplugged one of the joined and the first one joined!! I replugged the second one but could not join!! I unplugged the first one and replugged the second one: the second joined the controller but the first could not associate again!
Can 3600 series model AP work with WLC 4402 with existing license, we purchased 25 LIC pack and still using only 15. Any recommended Part no on 3600 series with external Antenna
View 5 Replies View RelatedWe have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC. The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL] Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
Error: AAA Authentication Failure for UserName:radiususername User Type: WLAN USER
I am using a window radius server. I have added my WLC 4402 as a radius client on my radius server.
I followed the instructions on the MS link : [URL]
I want to use my windows raduis authentication for WLC management login and Web-Auth for guest WLAN user login.
Our company has a customer with a Cisco 4402 WLC and a code version of 4.2.130.0 . The customer wants to upgrade the code to 7.0.230.0. Is there any flash size requirement when upgrading to 7.0.230.0? (upgrade train: 4.2.130.0 ----> 4.2.209.0 ----> 7.0.230.0), How can I find the flash size?
View 2 Replies View RelatedI need to install one 5508 and a 4402 together to bring redundancy to a wireless environment.Can I do this?. What are the neccesary steps to perform this?, the idea behind this is to bring redundancy is the primary WLC falls for any reason.
View 4 Replies View RelatedI have two wlc 4402 to control 50 AP 1131. 2 WLC: wlc-01 and wlc-02, wlc-02 config as backup wlc in the same mobility group. Client authentication:EAP with Microsoft IAS/AD.All AP have joined wlc-01. Wireless client work well with wlc-01.For testing I config access point AP01 have primary wlc: wlc-01, secondary: wlc-02 If I change config of AP01 like this: primary wlc: wlc-02, secondary: wlc-01. Client is hard to connect to wlc-02 and it only connect when client set static ip ALL wlc run this softwar image: 7-0-98-0 Should I send wlc-02 to warranty service?
View 8 Replies View RelatedI do get this error all the time on my WLC 4402 logs:
"Could not Register IP Add on MSCB. MSCB still in init state. Address:e4:ce:8f:13:e4:de[...It occurred 2 times.!]"
I have WLC 4402 working with AIR-AP1131AG-E-K9. Need to buy another pair. I looked to the side air-ap1041n-e-k9. Tell me whether or not the compatibility of the controller and the AP1041n? One more question. When buying in 1131 is still in the box and power cord to the point. The new 1041, the purchase comes with the point of the power cord?
View 13 Replies View RelatedI am trying to setup a Wireless Network on my WLC that is totaly independent of our internal LAN. Port1 is designated at the .14.0 network and Port2 is the .18.0 network. The 14 network (Port1) will be the guest and 18 network (Port2) the internal wireless.
The issue i am having is nothing is routing to Port1. I have the Guest Wireless set to get DHCP from the WLC and i can get an address but i cant get internet access. I tried configuring a Network Route but it will only let me set the service port as the Gateway and not the IP for Port1.
I am running software version 5.1.151.0 and using this guide as it is the only one i can find. [URL]
Here is a screen shot of my Interface config.
We are attempting to use LDAP for web authentication on a WLC 4402.
[URL]
You are able to connect to the SSID and it reidrects you to the login page as it should. When you enter your username and password you get a message that "the username and password combination you have entered is invalid." Based on the following log it looks like the LDAP bind is the issue.
*LDAP DB Task 1: Dec 19 11:19:26.584: %AAA-3-LDAP_CONNECT_SERVER_FAILED: ldap_db.c:1038 Could not connect to LDAP server 1, reason: 1005 (LDAP bind failed).
We are able to test the following configuration with ldp.exe successfully,
Server: ***.***.***.***
Port Number: 389
Bind Username: CiscoBYOT
[Code].....
I tried to upgrade the cisco boorloader pf WLC 4402 from version 4 to 7.2. I updated ER.Aes FOR 7.2 (EARLY RELEASE.aes). It was updated perfectly and then I rebooted controller....now i can only see blank screen from connected console.I tried the flash of other lan controller but its not working because the issue is in the ROM as the boadloader file is in the ROM which is corrupted now i want the solution to upgrade the boatloader file inside the ROM.
View 1 Replies View RelatedMy customer has a 4402-25-K9 and need a backup (failover) controller to avoid data transmision break when primary controller goes down.4402 are end of sale so I have a question can I use 5508 to get Controller Failover Protection with 4402 ?
View 3 Replies View RelatedWe have two cisco 1262 AP and a 4402 WLC, the AP cannot join the WLC.
The AP gets the address from dchp
I cannot ping the AP address from the WLC, but i can ping the default gateway and other VLAN addresses.
I already read the info on the this link : [URL]
Still our AP cannot join the WLC no matter what i have tried.
Setup
- VLAN setup on a Cisco 3560 48 port poe Switch
- tunk configured btwn the Gi Interface and the Management physical port
- WLC mode is configured for Layer 3
- AP Manager and Management are in the same Subnet
- Option 43 is configured for the with the AP Manager's IP address
- Opotion 60 is also configured with AP Manager's IP address
- the port connected to the APs are in the AP Manager VLAN
I have an issue with AP Fallback not working with two Cisco 4402-50 WLC's. Here is the senerio:
Site 1 has a 4402 (WLC01) running software 7.0.220.0 with 48 associated access points. AP Fallback is enabled in Controller > General and all 48 AP's are set to Critical failover with WLC01 being the primary controller and WLC02 (at site 2) being the secondary.
Site 2 is the location of WLC02 which is also running software 7.0.220.0 but has 0 ap's associated and also had AP Fallback set to enabled.
Your typical active/passive setup
The problem is when WLC01 goes down all of the AP's fail over to WLC02, however when the connection is restored to WLC01 we have to manually reboot each access point in order for them to reassociate back to the primary controller. Isn't AP Fallback enabled suppose to allow the AP's to move back to the primary controller once connection is reestablished?
I ##have a customer with WLC 4402 in use, running software version 7.0.98.0, and supporting 11 APs at present. The customer wants to enlarge the WLAN, which involves increasing the number of APs. I #####have purchased a new WLC5508, and have installed it onto the network alongside the 4402. the 5508 is running software version 7.0.116.0. Because the wireless network is critical to the user, we want to move the APs over to the new controller while the network is up and running, then remove the 4402.
However, when we set the 5508 as the master controller, or tell one of the APs to use the 5508 as its primary controller, the AP connects to the new controller, downloads the new software version, attempts to load it but reports an error with the unzipped file size of the software and fails to boot. formatting the flash on the AP, then disconnecting the 5508 from the network and rebooting the AP allows it to connect to the 4402, it downloads the older software and boots as normal. A new AP, if connected to the 5508 in a test scenario (ie no 4402) connects, downloads and boots perfectly.
I #have the upgrade software to allow the 4402 to be upgraded to 7.0.116.0, but I am concerned that, if this is installed, the existing APs will then fail to boot from the 4402 or the 5508.all APs are 3502s, running IOS version 12.04(23c)JA when connected to the 4402 and 12.04(23c)JA2 on the 5508.
We have two WLC 4402 WLC in active-active mode in our setup. The issue we see is that a user/laptop gets connected and gets the ip address but there will be no network access. We see a yellow exclamation sign at this time in network icon in tray and we can not ping gateway at this point. We have run debugs at this time for the machine and we could see that was in "RUN" state its only that the machine can not access network.
View 11 Replies View RelatedI 'm trying to upgrade WLC 4402 up from 5.1.151. After upgrade to 5.2 or higher https interface is inaccessible. If I use any other previous version, all is OK. Somewhere I found recomendation to open http before upgrade and use it at first. It works, but what to do next? To stay on http only?
View 1 Replies View RelatedAny instructions on performing an upgrade from a 4402 to 5508?
View 7 Replies View Relatedmy client claimed that right after thry upgraded their WLC 4402 to version 7.0.220.0 from the version that came preinstalled (factory) the can no longer console into the device. They were able to console into the 4402 before the upgrade but now they can't. I'm thinking that maybe they upgraded straight to the new version and didn't verify to see whether they were allowed to upgrade directly to that version 7.0.220.0 or if they needed to upgrade to a intermediate version , the proceed to upgrade to the 7.0.220.0.
View 3 Replies View Related