Cisco WAN :: 1841 Can't Able To Use Different Service Provider At Same Time
Mar 4, 2012
I have cisco 1841 router in my office.In that router we configured MPLS bgp with two different service provider. [code] We can't able to use the different service provider at the sametime.Cisco 1841 is support two different AS ???
View 12 Replies
ADVERTISEMENT
Feb 5, 2013
"The service provider in your current location is restricting access to the InternetYou need to log on with the service provider before you can establish a VPN session. You can try this by visiting any website with your browser."We are using an Internal IP....and the external, same resultI am the IT Admin and this was working last week till I upgraded to the newer anyconnect. Internet is just fine....I am at a loss.
View 7 Replies
View Related
Feb 25, 2012
My folks have Time Warner (Roadrunner) Internet service. They power-down their Dell every night. When they shut down last night they had no problems and were running Time Warner (Roadrunner). When they booted the computer this morning the computer is trying to connect to Adelphia.
They changed nothing. The wiring to the computer was not compromised in any way.
Time Warner tried to "ping" their modem and could not "see" the modem. They think it is a line problem - but the fact that the computer is looking to connect to an alternate service provider makes me think that it is possibly a problem with a setting in the computer.
View 1 Replies
View Related
Sep 10, 2012
I have Windows 2008 server running isa server with dedicated ip (which I take from my Internet Service Provider ISP) running my website, if my internet connection is down my website is not accessible from outside world.How can I switch to another ISP using same dedicated ip address when my ISP connection is down?
View 1 Replies
View Related
Jul 22, 2012
I have DNS setup through No-IP.com. How do I add this service provider to my WNDR3400v2 router? It only has DynDNS.org listed and I can't create a free account there.
View 1 Replies
View Related
Mar 27, 2012
how to separate two different static Ip address provided by different service provider in Sonic wall TZ-210
View 6 Replies
View Related
Jul 9, 2012
I have currently a Cisco 3600 router, it has three interfaces (all ethernet interfaces only).We being a client, our requirement is, we want two links one being the primary and one secondary for the fail over.My ISP has done certain configurations, but I am so puzzled what really has been done. I asked with them and they told that they have provided us one public IP 202.166.217.248 via Fibre--> Media Converter-->Ethernet 0/0.At the same time, they have given us a pool of addresses of the network 202.166.216.48/29 through the interface Ethernet 2/1.And we have used all the available public IPs in the server farm.They have told that, for the failover purpose via wireless, they have even used an IP address 202.166.213.114/25.
Now, where my confusion lies is, cant they provide the pool address via fibre? What is the significance of the ip that has been provided via fibre? What actually is its purpose? Isn't it consuming an extra interface ?Cant we have both the primary and secondary link excluding that one additional process?Or, am not understanding the real working mechanism how ISP distribute the internet?
View 1 Replies
View Related
Sep 4, 2012
Is this a wired or wireless connection issue? Both Who is your Internet Service Provider (ISP)? Comcast..What type of Broadband connection are you using? Cable..What is the exact Make and Model of your Modem, Router or Modem/Router Combo - (Main)Netgear WNR3700v2 / WNR2000v3(secondary) My current setup is the 3700 router is taking the internet from the modem cat5e and spewing the wireless. I would like to have the secondary router use the wireless from router 1 as the internet source and push the internet out of the 4 hardline ports so I can plug my upstairs xbox 360 into the router via cat5e. I'm just kinda new to this and still learning so I'm not sure how to configure the router to do this. I can get into the settings of the router just fine but finding the right settings to tweak is a little difficult.
View 3 Replies
View Related
Jun 3, 2012
I am trying to confgure a L2L VPN tunnel to a service provider using an ASA 5505.My problem is that the service provider will not accept traffic from a LAN subnet, they will only accept traffice from a public IP.We have a small public subnet of x.x.x.50/255.255.255.248, our public IP (outside interface IP on the ASA 5505) is x.x.x.50 and the service provider wants to see traffic coming from us on x.x.x.51How can I NAT our LAN subnet (10.0.0.0/24) to one public IP (x.x.x.51)?
View 14 Replies
View Related
Nov 4, 2012
I have a wired broadband connection with a modem. My internet service provider does not have Wi-Fi. Can I convert it myself into wi-fi by connecting it to a router. If possible how?
View 6 Replies
View Related
Aug 28, 2012
My modem with single network connectivity (Type I) works fine. I tried to replace with Type II modem (with wifi- and 4 or more ports) for connectivity. I could not establish connection with the server of the service provider. I tried to replace with a different type of typeII modem. Still the same. What could be the reason?I connected the same in a different workplace to a different PC.
View 1 Replies
View Related
Mar 14, 2007
WRT54G v7 - cannot specify service provider
View 9 Replies
View Related
Dec 19, 2012
How to configure load balancing in MPLS between two different service provider.
View 4 Replies
View Related
Mar 15, 2013
Region : Austria
Model : TL-MR3420
Hardware Version : V1
Firmware Version :
ISP : orange.at
When I first installed the router I used the built-in provider settings for "ONE" which used to be the name of the provider before it was taken over by orange.at. It seemed to work fine but I experienced some funny server errors with certain web services. I contacted orange.at about this and they told me to adjust the provider settings in the router as follows:
Dial number: *99#
APN: fullspeed
The reason for the problems was that they use different proxy servers for their services and applications. Now it works fine (so far).
View 1 Replies
View Related
Feb 7, 2013
So I have a 2600 that I have configured three sub interfaces on. FA0.0.1 is set for DHCP and supports VLAN 1. FA 0/0.2 for Voice, FA 0/0.3 for Data. I have this router interface plugged into FA 0/24 on my 3550 and the 3550 is configured as a dot1Q trunk (I have attached configs for RTR and SW).I have most ports configured as access VLAN 1 which is where i have my ISP connection plugged FA0/1 on the 3550. When I connect the service provider link FA0/0.1 never picks up an address. If I take my internal DHCP server and connect it to FA0/1 of the 3550 it snags an address almost immediately.In my mind this validates that my config is fine. I also took the same cable from the service provider cable modem and connected it to my laptop and the laptop is pulling DHCP.
View 4 Replies
View Related
Sep 3, 2010
If I have a wireless network set up with the Linksys E1000 using one internet provider and then change the internet provider service to someone else, do I have to reset up the network or is it simply a matter of connecting the new internet service to the router?
View 3 Replies
View Related
Jan 24, 2011
We have multiple sites that are linked via MPLS (L3) circuits. We have good size circuits for Internet at two main sites (HQ and QC) and smaller sites come to HQ site to go to internet. We are running ospf (Cisco L3 switches) with service provider (ME3400) at these two main sites and service provider then redistributes routes back into MPLS via BGP and then smaller sites ME3400 learn these routes. i am injecting default routes from HQ and QC, but Telco is only redistributing default from HQ. So large pipe Internet at QC is not being used effeciently. Also if MPLS at HQ fails, then we are told, we need to call Telco and they will make change in their network to now start distributing default from QC.it was my understanding that telco can use BGP communities and advertize one default as prefered and second with higher cost, so that failover can occur automatically. And that they can also set up so that west cost sites use HQ and east cost sites can use QC for going to internet, but they say it is not possible.it the least, can I do something like this at my end for failover for internet, in case MPLS at HQ goes down (soon we will be setting up a point to point VPN tunnel between HQ and QC so that MPLS failure at HQ will trigger advertisement of HQ routes over tunnel via QC into MPLS, so other sites can then come to HQ thru QC over this tunnel. At QC Cisco router (to detect loss of default route from HQ and then start advertizing default from QC)
router ospf 1
default-information originate always route-map From_HQ
exit
ip access-list standard From_HQ
[code]....
View 3 Replies
View Related
Jan 21, 2013
I have a port on 7600 connecting via Single Mode Fibre to my service provider. Service provider has 1000-Full with auto-negotiate. I am seeing following output on my 7600. [code] if this interface is only capable of doing 1000Mb, how come it is showing 100-Full. If I change to nonegotiate option (both my side and provider side), link goes down. My provider has confirmed they have 1000Full their side.
View 2 Replies
View Related
Mar 8, 2012
In cisco 1841 clock time is not stable.Every time the clock time is changed.
View 4 Replies
View Related
Oct 28, 2012
i had a client request to block ICMP request on their 1841 WAN link. i've got ACL hits for ACE 170 but not for 171.
how to test or simulate for ICMP time-exceeded? is this TTL related and is there a DOS command or any way to produce ping packet with a less TTL count that would hit the ACL log? below is the config.
interface FastEthernet0/0
ip address 202.42.x.y 255.255.255.252
ip access-group IDS_Fastethernet0/0_in_0 in
ip access-list extended IDS_Fastethernet0/0_in_0
[code]....
View 2 Replies
View Related
Apr 26, 2012
I want to be able to gather some time metrics based on source IP, and destination port. Is it possiable to track how much time a user spends using a service based on it's port number. I have figured out how to capture all the data, and I can then look at timestamps, but I would like a better way if possible. Can this be done at the firewall, or do I need a different appliance?
View 1 Replies
View Related
May 16, 2011
When I create a service object or group and add the object to a new rule it never works.I mean the traffic match not the rule. I see not hits.I placed the rule on top of my access list to check if I do somethink wrong but it is not working. When I place only a service for example tcp/23 it is working.
my ip service object
object-group service g-as400 description access client 2 as400 machine service-object tcp-udp destination eq 397 service-object tcp destination eq 137 service-object tcp destination eq 2001 service-object tcp destination eq 3000 service-object tcp destination eq 445 service-object tcp destination range 446 447 service-object tcp destination eq 449 service-object tcp destination eq 5010 service-object tcp destination eq 5544 service-object tcp destination eq 5555 service-object tcp destination range 8470 8476 service-object tcp destination eq 8480 service-object tcp destination eq
[code]...
View 8 Replies
View Related
Feb 28, 2012
We have a situation where services are stopped on the real servers. The probes fail and we confirm the services are not running on the server. We cannot access the ports from the ACE directly. We can still however acces the VIP on the TCP port (L4 VIP class-map). So we can still telnet to the VIP on the port from thr Client side of the network.This is on ACE 20 Modules deployed in Routed mode. The version of software is A2(3.3).
Tried removing multi-match and loadbalance policies as well as class-map and re-applying then re-appyling the service policy to interface. Same behavior,This is a problem at another level as some services are being monitored by GSS via TCP keep-Alive and this obviuosly causes a problem as the service then never goes off-line.
View 10 Replies
View Related
Mar 25, 2013
I have a fresh installation of LMS 4.0 on windows server 2003, when i click to open topology i get error message : ANIServer service may be down or Host name isn't DNS resolvable
i tried pdshow -brief ANIServer ===> service UP
DNS is working using host file in driversetc i restarted the server
restared the crmdmgtd
unistall / install java plugin
pdterm ANIServer
pdexec ANIServer
NO change ..
View 6 Replies
View Related
Jan 4, 2011
I have one 2621 router i want to creat time base access list so that one of my subnet user(10.128.194.0 255.255.255.128) use only internet between 11am to 2pm.
View 15 Replies
View Related
Jul 8, 2012
I just bought a WAP321 Wireless AP. I wonder why it cannot sync with our time server automatically. Every time I reboot it, the system time become "Fri Dec 31 1999 12:00:00 UCT". I have to do the sync manually by clicking on the "Save" button under the menu Administration > Time Setting.
View 5 Replies
View Related
Jun 29, 2011
Ciso 1941 router frozen once a day, sometimes after 2 to 7 days. When the router frozen, no internet connection and cannot login/ping ethernet ports. I can login to console port and copy the error messages below. Reload the router and it will return back to normal operation. Re-installed IOS but still the same.
IOS Version 15.1(2)T2,
Cisco CISCO1941/K9 (revision 1.0) with 487424K/36864K bytes of memory.
DRAM configuration is 64 bits wide with parity disabled.
255K bytes of non-volatile configuration memory.
250880K bytes of ATA System CompactFlash 0 (Read/Write)
[code]...
View 5 Replies
View Related
Oct 26, 2011
I have WRT54G2 router. All settings are more-less default and the behavior is following.You start up the router. If you do not connect wireless device within 10 minutes, then you have to restart the router.You have assigned IP via wifi, and when you connect cable device to the router, the wifi PCs are disconnected.
View 3 Replies
View Related
May 1, 2012
I recently purchased a X2000 ADSL modem/router combination. For some reason the current time will not stay set to the time zone. Rebooting clears the discrepancy for a short time before it drops an hour exactly. I'm in the central time zone and the setting are correct on the basic setup.?
View 1 Replies
View Related
Jan 17, 2012
Is the WAG320N iPv6 compatable ? ,or could it be with a firmware update ?.Is the X2000 in the same boat in iPv6 terms as th WAG320N ?.Is there a way of retrieving "UPTIME" / "DSL connection time" information from the WAG320N and also line attenuation stats etc.Wouldn't need the above but poor isp needs keeping an eye on.
View 3 Replies
View Related
Jun 6, 2012
I have a Time Warner modem/router. There are a ton of different devices constantly being connected/disconnected to our router - itouches, computers, smartphones etc.
The problem started with my otherwise super reliable HP g42 (i3) laptop. Nothing would solve the issue other than recovering it back a few days to when the issue wasn't happening. But then it would happen again after a few days. All other devices would connect without issue.
Time warner's technical troubleshooting consists of "unplug the router for 10 seconds and then plug it back in. Did that work?"
So now, my son gets his first computer and I bring it home last night. Also an HP (pavillion -i3). Same deal. At first, it connects fine and dandy. Then after about 2 hours it get the ol' "won't connect - diagnose the problem?" After diagnose, it says "DNS server may not be available.
Here's the thing: Both computers connect immediately and without issue to my smartphone wireless tether.
View 6 Replies
View Related
Nov 18, 2011
My internet service is telling me all of a sudden that my computer has no IP address for my laptop to connect to the modem?? The laptop was given to me so I have none of the disks or anything. How do I get an IP address to be able to use my internet provider?
View 2 Replies
View Related
Dec 17, 2012
What's the best free dynamic DNS provider?
I found a ton of them on the internet but I'm not sure which ones are safe.I'm trying to use my home NAS as an ftp server that can be accessed remotely.
View 3 Replies
View Related