Cisco Switching/Routing :: Asr 1004 - How To Check SFP If It Receives Power
Nov 29, 2012on the asr 1004 , how test and check if the SFP receive power or signal from the MUX? any command to do that?
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: 2960g-24tc-l Internal Power Supply Pinout / Voltage Check
Feb 25, 2013I had a bad power surge yesterday that took out a 2960g switch and the APC UPS that it was connected too. when plugged in the fan comes on and the syst light stays amber and the rps, stat, duplex. and speed light stay lit and the port lights for ports 21-24 stay lit. plugging it into the console on boot I cant even see rommon, so i dont think its even booting. I would like to find a pinout and voltage guide for the connector comming off the power supply so I can check the voltages coming off the power supply to tell if it is a bad PSU or if it took out the main board.
View 2 Replies View RelatedLAN Card Is Not Responding But It Only Receives Light From The Power Source
Feb 1, 2012my LAN card is not responding but it only receives light from the power source?how can i make it work?
View 1 Replies View RelatedCisco Switching/Routing :: ASR 1004 - How To Create L3 Interface
Jul 19, 2012I am in the process of staging a couple of two new Cisco ASR 1004's which are located at two locations with a WAN link in between. I need to set up connectivity between servers plugged directly into each ASR router across the WAN link. The ASR has 16 gig interfaces (gi0/0/0 - gi0/0/7 and gi0/1/0 - gi 0/1/7), and a management interface (gi0). I have connected the WAN link to gi0/0/0 and put an ip address on it. The servers will be plugged into the remaining gig interfaces. I tried to create an SVI (vlan interface) in an attempt to create an L3 interface to support routing to these servers but these routers don't allow SVI's to be created. how to put these server connected ports on a vlan and to create an L3 interface to provide routing to them?
View 1 Replies View RelatedCisco Switching/Routing :: Show Command In ASR 1004 For Running Diagnostics
Aug 29, 2012is there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 Replies View RelatedCisco Switching/Routing :: Multiple VLAN Extension From Nexus7k To ASR 1004
Mar 6, 2013We bought a pair of ASR 1004 to be installed at Primar & Secondary data center and one thing is to run OTV over it, but to do that, I have to extend multiple VLANs from my Core (Pair of Nexus 7010s) connected directly to the ASR is Primary Data center, I looked at some documents but didn't get a good idea about it, extend multiple VLANs from Nexus switch to an ASR.
View 2 Replies View RelatedCisco Switching/Routing :: 3750 - Power Stack Has Unbalanced Power Supplies
Jun 9, 2013I am receiving the following error on 3750 stack switches. have already verified the power status and found ok.
IOS used: Cisco IOS Software, C3750E Software (C3750E-UNIVERSALK9-M), Version 12.2(55)SE3, RELEASE SOFTWARE (fc1)
211540: Jun 10 10:45:17.935 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS: Switch 4's power stack has unbalanced power supplies
211541: Jun 10 10:46:18.045 UTC: %PLATFORM_STACKPOWER-4-UNBALANCED_PS:
[Code]....
Cisco Switching/Routing :: Stack-power 3750x / FRU Power Supply Is Not Responding
Sep 4, 2012After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
Cisco Switching/Routing :: WS-C3560-48PS-S Show Power Inline But No Power Available
Apr 14, 2013We have two switches of the same model (WS-C3560-48PS-S) that are not providing PoE. I'm trying to remotely determine what the cause of the issue is.
Here is some output.
Hostname#show power inlineAvailable:0.0(w) Used:0.0(w) Remaining:0.0(w)
Interface Admin Oper Power Device Class Max (Watts)--------- ------ ---------- ------- ------------------- ----- ----Fa0/1 auto off 0.0 n/a n/a 15.4Fa0/2 auto off 0.0 n/a n/a 15.4Fa0/3 auto off 0.0 n/a n/a 15.4Fa0/4 auto off 0.0 n/a n/a 15.4Fa0/5 auto off 0.0 n/a n/a 15.4Fa0/6 auto off 0.0 n/a n/a 15.4Fa0/7 auto off 0.0 n/a n/a 15.4Fa0/8 auto off 0.0 n/a n/a 15.4Fa0/9 auto off 0.0 n/a n/a 15.4Fa0/10 auto off 0.0 n/a n/a 15.4(code)
Cisco Switching/Routing :: 6500 - Power-Redundancy Mode Combined And Power Fail
Feb 28, 2011I have a 6500 chassis with 2 power supplies. At the moment I am using the default configuration:
power-redudancy mode redundant
The problem is that an inserted module is in "power deny" state due too insufficient power.
I know, that It's not a good idea to change into combined mode (loss of redundancy), but my customers requested this anyway.
So I will change to combined mode. So here's the 1 million dollar question: "Which modules will go into power deny, if one of my power supplies fails?"
The 6500 config guide states:
"Power supply is removed withredundancy disabled
• System log and syslog messages are generated.
• System power is decreased to the power capability of one supply.
• If there is not enough power for all previously powered-up modules, some modulesare powered down and marked as power-deny in the show power oper state field."
Well, do you know if there's any way to configure some kind of priority? E.g. I definetly don't want by 10Gig Module or WiSM module to be in power deny. Can i statically make sure, those module will be powered on for sure? Like: "power enable module slot_number" How is this calculated? Or is random?
Cisco Switching/Routing :: 3750X Stand Alone Secondary Power Supply Act As Pool Of Power
Apr 4, 2012In a stand alone 3750x switch configuration, can the secondary power supply only act as a redundant power supply (active/standby), or can it become a "pool" of power similar to power sharing mode for StackPower (somewhat active/active)? I understand there is no stack involved here but I'm curious if this functionality is possible.
View 1 Replies View RelatedCisco WAN :: 7206vxr Router - How To Check Received Power On OC3 SFP
Mar 8, 2011we have a 7206vxr router with pa-pos-2oc3 and SFP-OC3-IR1-C. Our provider wants us to check transmitted and received power on the SFP.
I already looked around and know theres no way to check or adjust transmit power and saw its -15 to -8dbm on the datasheet.
Is there a way to check received power?
IOS version
7200 Software (C7200P-ADVENTERPRISEK9-M), Version 12.4(24)T3
Cisco Switching/Routing :: Check IOS Version On A Standby Sup On Cat6500?
Jan 11, 2012I wonder whethere it is possible to check the the IOS version on the standby sup720 of a 6500? if yes, what command would you use?
View 5 Replies View RelatedCisco Switching/Routing :: Inconsistency Check In N2K Access Port
Dec 25, 2011We have configured a Fex port as acces port but the port no up becouse appear in suspended state, i think the problem is a vlan mistmach as appear in the consistence-parameter information but i not found in what part allow the correct vlan, the N2K are connected to 2 N5K, and 5K are connected to2 N7K
%ETHPORT-3-IF_ERROR_VLANS_SUSPENDED: VLANs 41 on Interface Ethernet101/1/48 are being susp ended. (Reason: Vlan is not configured on remote vPC interface) [code]
Cisco Switching/Routing :: Check History Alarms In Router 7609?
Oct 26, 20111. How to check the history alarms in Router 7609?
2. How to check whether an Interface was down?
Cisco Switching/Routing :: Check QoS Counters And Stats For Interfaces On Cat 6509?
Oct 28, 2012how I can check the qos counters and stats for interfaces on my cat 6509 ?
View 1 Replies View RelatedCisco Switching/Routing :: FIPS Flash Key Check End Not Found With 3750
Jan 17, 2013Cisco... Have two new 3750X switches (24P-L, and 48PF) trying to stack. Brought them up together a few weeks ago with the 24P using LANBase and the 48 IPBase. The expected happened. They saw each other in the stack ring, and the 24 port was excluded due to license miss match. This was corrected. Now both are IPBase.Now I have the two switches stacked, and boot the 48 and 24 at the same time. Monitoring the 48 I get a check message "FIPS: Flash key check: End, Not found. FIPS: Stacking Not Found". The 48 does confirm the stack cable is connected. This happens early in the boot process, before master election.OK.... Now looking at the 24 Port. After applying the new license, and actually booting successfully and few times. It will no longer load the boot file. Wants an environment variable. Going to have to dig into ancient history for that. Had to deal with that one about 8 years ago. Do not feel that is part of the stack disable issue though.
View 2 Replies View RelatedCisco Switching/Routing :: Command To Check Memory Slot In 3800 Routers?
Nov 13, 2011I remember there is one command which can tell you which memory slot has how much big memory in Cisco 2800 or 3800. But at this moment, I just couldn't recall this command. I checked "show diag" but didn't see any information about memory.
View 9 Replies View RelatedCisco Switching/Routing :: 3560 And 3750 - Any Way To Check For MLS QoS Input Queue Drops?
Feb 10, 2012I feel that 3560 and 3750 perform differently with the following two commands:
srr-queue bandwidth shape 5 0 0 0
srr-queue bandwidth limit 50
On 3750, the bandwidth for queue 1 is limited to 100mbps x 50% / 5 = 10mbps
On 3560, the bandwidth for queue 1 is limited to the smaller value of BW / shape weight and BW x limit%.
Does it sound about right? is there a way to check for mls qos input queue drops? The show mls qos interface xxx stat only shows the output queue drops. Maybe for some reason the input queue never drops?
Cisco Switching/Routing :: WS-C6513 Command To Check 6500 Switch Performance / Resource Usage
Apr 25, 2013I am on a call right now troubleshooting some latency issue. The CPU usage on the sup card is low. Don't see any drops or input errors. I am aware that the switch and its modules have capability limits. Is there command I can run which will tell me if any module is overloaded or if the fabric/backplane is over utilized?My chassis is WS-C6513 and sup card is WS-SUP720-3B.
View 3 Replies View RelatedCisco Switching/Routing :: Power Connect 6224 With Routing Enabled With Several VLAN Setup
Jan 19, 2013I have a power conncet 6224 with routing enabled with several VLANs setup.VLAN Database: 6,8,10,90-254VLAN 6 is our management vlan10 is for our core network services (DNS, Domain, Exchange etc)90-254 are isolated vlans.What I need to accomplish is to prevent vlans 90-254 from communicating with each other and only allow communication to VLAN 10 and the internet. All internet firewall work will be handled by our Sonicwall. [code]
View 1 Replies View RelatedCisco Switching/Routing :: 3750-x Won't Power Up
Oct 31, 2012I recently bought a bunch of cisco 3750-x switches. I configured them all and started deploying them. A day later, some of the switches started failing on me. When I connect the power cord to the AC main, the power supply module on the back shows "AC OK" LED Green but the "PS OK" LED shows Red. I started referring to the installation guide and it told me that "PS OK" LED turns RED when output has failed. Guessing this I checked with another power supply module that was working, but still I get the same LED indicators.The original power supply module works with other switches.IOS crash...?
View 5 Replies View RelatedCisco Switching/Routing :: How To Power 3560CG-8PC-S By PoE
Sep 4, 2012I got some specs here that I can't seem to match with any existing switch - unless the 350CG-8PC-S can be powered by PoE.Let me quickly put down the important specs.
8x Gigabit ports
2x 1G Copper or 1G SFP Uplinks (It'll be a 1x Copper and 1x SFP setup)
support for PoE passthrough ( so just capable of it, provided it's 2x Copper Uplinks )
Does that match the 350CG-8PC-S ?
Cisco Switching/Routing :: 2960 - Power LED Does Not Come Up
Jul 22, 2012Have Cisco catalyst 2960 IOS ver12.2(53)se2 when power on the power LED does not come up and on this is what shown on hyper terminal. what need to be done for this switch ?
Boot Sector Filesystem (bs) installed, fsid: 2
Base ethernet MAC Address: b4:d9:8d:27:4c:00
Xmodem file system is available.
[code]......
Interrupt within 5 seconds to abort boot process. Boot process failed. The system is unable to boot automatically. The BOOT environment variable needs to be set to a boot able image.
Cisco Switching/Routing :: 3750X Power Needs For PoE
Mar 21, 2013I am building a switch stack using 4 48 port 3750X switches that will also have the power stacked. If I install a single 715W power supply in each switch will the stack support 802.3af accross all 48 ports on each switch? My calculations are 48 ports x 15.4W which gives me almost 740W needed which is over hte 715W power supply. I was reading somewhere were it mentioned that in a powerstack additional power can be drawn from the stack. I know this will not work if you are trying to support power on all switches accross all ports but would it if say 2 of the 4 switches are needing to provide PoE accross all 48 ports? If I say we can only use 24 ports per switch for PoE that drops the power need down to 370W which I believe should work. Just trying to get a better understanding of PoE consumption. Would the best solution be to just add a second power supply to each switch?
View 8 Replies View RelatedCisco Switching/Routing :: Sd208p Will Not Power A 7960
Sep 28, 2012I have a small business SD208p P.O.E switch that will not power a 7960 VoIP phone over P.O.E. It currently is powering a 7965 VoIP phone and a WiFI access point. what's wrong? I have tried several different VoIP phone's & port combo's.
View 1 Replies View RelatedCisco Switching/Routing :: Power Requirement For 6506E
Jun 2, 2013I am looking the power requirement for 6506E in data sheet and it shows that is support 3000, 4000, 6000 & 8700W. I have currentely 4000W power source for my new 6506E switch. will it work with below modules in new 6506e ?
View 2 Replies View RelatedCisco Switching/Routing :: Power Consumption On 4507R
Aug 2, 2010We are planning for the office move and I need to estimate how much power we need to run a fully populated Cat4507R switch. The chassis include 2 Sups, one 6-port fiber line card, two 48-port Gig and two 48-port FastEthernet line cards. The switch also has redundant power supply (4200ACV 1400W). According to Cisco Power Calculator [URL], I need 49.5 amp 110-120V circuit. It seems to be too much higher than real world. How many 20amp circuit we would need when all the ports are fully utilized?
View 3 Replies View RelatedCisco Switching/Routing :: Required Power For WS-SVC-NAM3-6G-K9?
Oct 1, 2012What is required power in Watts for this card in Catalyst 6500? Or the "show power" ouput with this card included?
View 2 Replies View RelatedCisco Switching/Routing :: How To Increase PoE Power On 2960-s
Oct 16, 2012I got a Cisco 2960-S LAN (support PoE+) switch installed in one of my customers' office. The customer needs to plug some cameras to the switch and need inline power from the swtich.
Two of the cameras requires 24W power in order to work correctly, if just use normal PoE power, can't get all functions working and get an error message on the screen says "not enough power" or something like that. I have configured those two port to static power inline (on a max value which is 30W). Once the configuration applied, shut/ no shut the port, the error message disappeares for a few minutes, and then comes back. Looks like the power level is still on PoE not PoE+.
Is there anything I can do on the configuration to increase the inline power and provide a stable power to that kind of devices?
SW02#sh power inline
Module Available Used Remaining (Watts) (Watts) (Watts) ------ --------- -------- ---------1 370.0 141.7 228.3Interface Admin Oper Power
[Code]....
Cisco Switching/Routing :: Power Consumption On Nexus 7K?
Jun 5, 2012What is the power consumption of the 6-port 40G M2 module for the NExus 7K?
It says "TBD" on the data sheet for the M2....and it says nothing about power for the Supervisos.
I need to know what the power draw is on a 7009 chassis, with 1 SUP and 5 of these cards....
Cisco Switching/Routing :: WS-C4506-E Sometimes Phones Will Not Take Power
Mar 12, 2013We are facing problem with Cisco IP phones which are connected to module WS-X4248-RJ45V.Phones are getting restarted and sometimes phones will not take power.Initially we suspected issue with power consumption, but we have enough power in the module.
View 3 Replies View RelatedCisco Switching/Routing :: What Is Power Consumption Of 3560
Jan 4, 2012I have 2 x 3560e-24td-s
2 x ASA5510
2 x 2821(no modules)
2 x 2901
I'm trying to figure out power draw in Amps for my new cabinet. I looked at the data sheet for the 2821 and it says 3A for the 110V under the row AC Input Current, Would that be accurate if I did that for all the models and then just added up the total?
