LAN Card Is Not Responding But It Only Receives Light From The Power Source
Feb 1, 2012my LAN card is not responding but it only receives light from the power source?how can i make it work?
View 1 Replies
ADVERTISEMENT
Linksys Wired Router :: RV042 Control Light Blinking But Never Receives Dhcp Settings
Feb 15, 2010I have a problem with RV042. My ISP gives me automaticly IP address and i had no problems using different types of routers, including linksys routers. With RV042 i just can't get the IP. It says, the port is up, i see the packets/traffic, front control light is blinking but it never receives the dhcp settings, doesn't matter if i use wan1, wan2, dual wan mode or single wan. I have the newest firmare 1.3.12.19tm. System statistics says "disconnected" but the packets come in and go out. Log shows absolutely nothing. I also disabled firewall but it didn't work. I can't seem to find the older 1.3.12.6 firmware.
View 7 Replies View RelatedCisco Switching/Routing :: Asr 1004 - How To Check SFP If It Receives Power
Nov 29, 2012on the asr 1004 , how test and check if the SFP receive power or signal from the MUX? any command to do that?
View 3 Replies View RelatedCisco Switching/Routing :: Stack-power 3750x / FRU Power Supply Is Not Responding
Sep 4, 2012After stacking two 3750X switches, with four equal power-supply's, with StackWise and PowerStack , still got the next message every few hours %PLATFORM_ENV-1-FRU_PS_ACCESS: FRU Power Supply is not responding (gn4m-rt1p08-04-2)( note that the message revers to the second switch in the stack ) although the stackwise and powerstack on the switches is oke and are working correctly. !
Config : Stack-power in power-sharing mode/strict With CLI on the switch : All the power supply's and stack-power details, prio look OK.
Only: LMS prime /inventory/cisco-view/configure/power supply status result : some power supply's are marked as disabled.with the command > power supply 2 slot a off/on I manage to get the status back to "normal", but after a few hours some power supply's are again marked as "disabled".
Looks like SNMP en IOS difference from opinion.
Hardware
WS-C3750X-24S-S
C3KX-PWR-350WAC
Software
15.0(2)SE
C3750E-UNIVERSALK9-M
Cisco WAN :: 2800 Series Router With 28VDC Power Source
Oct 3, 2011Any problem/issue with using 28VDC to power the 2811 router. The spec calls for a 24VDC power.
View 1 Replies View RelatedCisco Switching/Routing :: 3750G-12s-s Switch Reboot When Power Source Restore From RPS To AC?
Dec 7, 2011I am facing switch reboot issue when power of switch restore from RPS to AC.
View 1 Replies View RelatedRouter Power Light Off After Flashing Firmware
Jul 31, 2011So, I messed around with my router a little too much and just want to restore it back to the original firmware now. I have a WRT54GS v7 Linksys router and tried to follow this guide to flash the firmware to something a little more useful. After step 7 of that guide, I can't ping my router, can't access the GUI, and have no idea what my router's IP is. If I assign each computer plugged into the router an IP like 192.168.1.2 I can ping them, so the router is still functioning somewhat. I'm plugged into my modem right now to get on the Internet.
Right now, my power light is off, my DMZ light is off, my WLAN light is off, but the other lights turn on if I plug a cord into its port (plug a computer into port 1, port 1's light comes on). When I do an ipconfig /all i get this. I doubt the web interface still works, but if I could at least get the router's IP, couldn't I use tftp and put the firmware on that way?
D-Link DIR-615 :: Revision Id / Yellow Power Light
Apr 15, 20111 =if its a rev 1c on the sticker that makes it DIR-615_REVC I am assuming
2= suddenly it shut down today yellow power lite , i cycled and nothing i reset then got a request to do a firmware update! I shut it down for a hour cycled and after a few minutes green power lite all my settings were still in place?I would think a reset would wipe this out.Its only 2 years old and would be surprised if its dieing.
Linksys Cable / DSL :: WAG120N Red Power Light
Apr 4, 2012My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies View RelatedD-Link DIR-615 :: Power Light Goes Amber And Nothing Works
Mar 24, 2013I have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies View RelatedD-Link DIR-615 :: Power Light Is Off But WAN-L1-L2-L3-L4 Are Solid Green
Dec 23, 2012I have a DIR-615 v e3 router
Did a bad dd-wrt flash and now all it does:
-no power light
-solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once
D-Link DAP-1522 :: DIR 655 - Blinking Power Light
Dec 9, 2009I successfully linked a DIR-655 (A4, FW:1.21) via WPS.
I then updated the DAP-1522 to FW:1.21 from 1.1.
Things looked great. I then moved it upstairs to my home theater.
Plugged it in and got a blinking power light. Completely unresponsive to either linkage or 192.168.0.50.
I have followed everyone advice listed either here or in Amazons reviews. And from my own experience with similar electronics the flashing power LED is indicative of a "brick".
I have initiated a replacement shipment from amazon. Just wanted to see if anyone had seen this before.
D-Link DIR-615 :: Cannot Connect To Internet / Orange Power Light
Mar 11, 2012I reseted my router because I couldn't go in the login so now eveything is green except the earth looking thing next.the power it is orange Cause I really need my internet
View 1 Replies View RelatedD-Link DIR-615 :: Low Input Voltage Not Connecting Power Light Ok
Dec 18, 2011My Dir-615 stopped working some weeks ago and I switched to another router until I had time to look at it. Tonight I checked the ps voltage and it read exactly +5v but just for a test I tried another 5v ps (which tested a little higher) and it worked. The ps that works reads about link +7vdc. Before this the power light came on with the occasional blink but I could't connect.
View 5 Replies View RelatedLinksys Wireless Router :: WRT54G V8 Power And LAN Light Won't Come On
Jan 24, 2009Ive recently tried to update the firmware and everything went as instructed, then the power and LAN light went out. Now I have the indicator lights for the computer and modem, but thats is. No internet or SSID broadcast. I cannot log into or ping the unit, and have tried the hard reset many times, with no effect.
View 8 Replies View RelatedCisco Switching/Routing :: 3550 EMI Switch Is Not Responding To Power Connection
May 10, 2012My cisco 3550 EMI switch is not responding to power connection. I have checked and changed power cable. its still not working.fan is not running and no lights on front panel
View 3 Replies View RelatedThomson TG784 Router - Power And Ethernet Light Is Blinking
Aug 21, 2012I have a Thomson TG784 router and i have a problem with it. once i turn on my rouet, and no cables are plugged in, except the power one, the two lights start blinking. The Power and the Ethernet ligh blinking. Once i connect my Ethernet cable and my DSL cable, the light are still blinking with no changes... What should i do?
View 1 Replies View RelatedLinksys Wireless Router :: Power Light On Wrt54g V2.2 Keeps Blinking
Oct 29, 2011the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected
View 3 Replies View RelatedLinksys Wireless Router :: X2000 Still Working But Only Red Power Light On
Jun 19, 2012My Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).
View 3 Replies View RelatedLinksys Wireless Router :: WRT54G Blinking Power Light
Jul 4, 2006My Wireless-G WRT54G router has a blinking power light and the startup software says "Unable to connect to the Router! Check that the Router has been connected to the computer, and that your Ethernet adapter is working." I tried uploading the firmware but I can't get to the router page to update. Is there a known problem or solution here or am I just going to have to find the router page?
View 9 Replies View RelatedLinksys Wireless Router :: WRT160N Power Light Blinking?
May 11, 2009So I recently upgraded from a WRT54GS to a WRT160N v2, all was well and good for about 3 days. Then I would lose my internet connection every 5 minutes or so, it would fix itself by the time I could open up command prompt and start pinging to pin point the problem. I decided I would update the firmware to see if that would fix the issue. Since doing that the power light has been blinking non stop. I've tried restoring it to factory defaults by holding the reset button for 30seconds, turning it off for 2 minutes and back on. That little blue light just keeps flashing. I can't even access the router setting page using 192.168.1.1. My OS is Windows xp x64 sp2, and I have DSL.
View 9 Replies View RelatedLinksys Wireless Router :: WRT54G 2.4 GHz Power Light Not Illuminated?
May 17, 2008My router was working fine until today. I figured it out when I tried to get on the internet and it wouldn't let me. I hooked up the ethernet directly from my modem to my computer and then my internet worked fine.
View 4 Replies View RelatedLinksys Wireless Router :: WRT54G V5 Blinking Power Light
Oct 29, 2011I need fixing my router. I updated the firmware and it said the upload has failed ever since then:
-the router doesn't work
-blinking power light
-DMZ light doesn't turn on
-can't access 192.168.1.1
My router is a WRT54G v5
Cisco Routers :: SRP 527W Power Light Flashing / LAN Lights On
Aug 9, 2011We have a Cisco SRP 527W router that was not showing up on the LAN. so we tried a Factory Default reset but it seems to be dead.
The power light is flashing constantly,the 4 LAN light are constantly on,the DSL Data light comes on for 1 sec when device is powered up.
i have tried connecting directly to a PC, the NIC reports as network cable unplugged.i have tried the (power on device, hold down reset button, power of after 30 sec, power on after 5 sec, release reset button after 5 sec) but still "network cable unplugged".
the firmware flash utility will not find the NIC the device is connected to.the router is less than a year old, is there a fix or is it a warranty replacement ?
Linksys Wireless Router :: WRT54G - Power Light Keeps Blinking
Feb 3, 2012the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected, what should i do?
View 1 Replies View RelatedD-Link DFE-520TX / PCI Ethernet Card Not Responding To Cable?
Aug 11, 2012A few days ago my mother's computer suffered a burned out motherboard ethernet adapter due to the PPPoE box on the roof of our building getting hit during a thunderstorm (apparently). I decided to buy a separate ethernet card, as her computer had a PCI slot free at the time - why not use it? I ended up buying a cheapo D-Link DFE-520TX. Anyway, I took it home, booted up the computer (running Windows XP with SP2 I believe) and installed the drivers supplied with the card. The instructions clearly stated to install drivers first, then physically install the card. I did so - everything went smoothly, popped the card in, booted the computer up again. Card was found, no problems. Except when I plugged the network cable in, the card remained idle. No blinking green activity light, no reaction from the Local Area Connection on the computer, nothing. Device Manager/Properties tells me everything is working just fine - except that the card itself doesn't "work". Took it back to the store, they plugged it into their test machine - everything worked just fine, green light blinking, internet access, etc. I've since tried uninstalling and reinstalling the device, swapping PCI slots (the second one is taken up by a Sound Blaster Pro). No dice - the audio card works in either slot, the network card doesn't work anywhere.
View 5 Replies View RelatedLinksys Wireless Router :: WRT54GS V1.0 Firmware - Blinking Power Light
Feb 20, 2012No download available and none available via Linksys Live Chat or FTP and having spent the best part of the week trying to find relevant firmware on other forums I decided to come here to get answers to the following questions, hopefully from version 1.0 experienced owners or not.
#1. Can the firmware of version 2.0 and 3.0 be reduced to flash version 1.0?
#2. When diagnosing the blinking power light issue by connecting directly to the router and the network card using "ping -t 192.168.1.xxx" which network address do I use, 192.168.1.1 or 192.168.1.2 to 2xx?
I get a reply using 192.168.1.1 but I'm not sure that works when using the TFTP Utility if it's the wrong address on my Laptop to ping?
Linksys Wireless Router :: WRT120n Not Working / Only Power Light Is Turning On
Sep 9, 2011I have WRT 120 N which has apparently stopped working. When I turn it on, only the power led turns on without blinking, no other light flashes. My computer can't detect the router signals since the signal light is off. Neither does my modem show that the router is connected to it through the ethernet cable. My ethernet cable is working fine, since it is working directly with the computer.
View 6 Replies View RelatedLinksys Wireless Router :: WRT54GS / Power Light Blinking - Internet Is Down
Feb 21, 2012I have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard. The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message: "Firefox can't find the server". I was no longer able to access the internet, and the router's green power light was left flashing. It flashed for over 24 hours. I tried unplugging the router and shutting down the computer, then plugging in the router and turning on the computer. (I don't have a modem.) The light was still flashing. I tried pressing the logo button for 5 seconds. Still flashing. Tried pressing the reset button in the back. Still flashing. 'I can't get on the internet or into the router. Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.
View 8 Replies View RelatedLinksys Wireless Router :: WRT54G V5 With Blinking Power Light Connected
Mar 24, 2011I've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?
View 4 Replies View RelatedLinksys Wireless Router :: WRT610N Power Light Flashing / Not Stable
Oct 2, 2011i have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem
View 1 Replies View RelatedLinksys Wireless Router :: WRT300n Version 1.1 - Power Light Blinking
Aug 15, 2011If I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies View RelatedCisco Wireless :: Power Cord For Light Pole Installation R3P-40NA
May 22, 2013Using following part for outdoor mesh AP power feed:
40-ft (12.2-m) power cord (AIR-CORD-R3P-40NA=) for light pole installations in the US and Canada.
I wonder what happens when the lights turn off?