Using following part for outdoor mesh AP power feed:
40-ft (12.2-m) power cord (AIR-CORD-R3P-40NA=) for light pole installations in the US and Canada.
I wonder what happens when the lights turn off?
My DIR-825 stays on even when I flick the power switch, for as long as I don't disconnect the externally powered Belkin USB hub from it. Some lights do come off, Internet light turns orange, but it stays on. If I disconnect the hub before trying to shut down the router, it turns off instantly.
I feel slightly worried by this because as far as I am aware, a USB client device shouldn't be feeding power to the host. On the other hand, the host shouldn't be accepting power from the client either.
Also, sometimes after days since last reboot, the USB light on the router is not on despite connected devices, and they may or may not appear in Shareport.
Is the CAB-C15-CBN - Cabinet Jumper Power Cord, 250 VAC 13A, C14-C15 Connector, supported on the Cisco Catalyst 3750X/3560X. I need to plug the switches into a UPS PDU, that requires a C14 plug.
View 2 Replies View RelatedI need to prepare a Bill of Material for WS-C3560G-48PS-S switch.
Whether we should go for CAB-AC-JPN - AC power cord for Japan OR CAB-AC-ACE AC power cord for Europ
Currently I am using 1000W power supply in Cisco 4500 and I want to upgrade to 2800W power supply.My question is
1) Whether I have to change the power cord while upgrading power supply
2)Whether power cord comes along with the Power Supply while ordering from Cisco
Once I unplug my toshiba saelillite power cord from the laptop itself, I lose my internet connection. Once I plug power cord back into the laptop, I am back online
View 6 Replies View RelatedIve recently tried to update the firmware and everything went as instructed, then the power and LAN light went out. Now I have the indicator lights for the computer and modem, but thats is. No internet or SSID broadcast. I cannot log into or ping the unit, and have tried the hard reset many times, with no effect.
View 8 Replies View Relatedthe power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected
View 3 Replies View RelatedMy Linksys X2000 still working but only red power light on (at nomal there are 3 white light on).
View 3 Replies View RelatedMy Wireless-G WRT54G router has a blinking power light and the startup software says "Unable to connect to the Router! Check that the Router has been connected to the computer, and that your Ethernet adapter is working." I tried uploading the firmware but I can't get to the router page to update. Is there a known problem or solution here or am I just going to have to find the router page?
View 9 Replies View RelatedSo I recently upgraded from a WRT54GS to a WRT160N v2, all was well and good for about 3 days. Then I would lose my internet connection every 5 minutes or so, it would fix itself by the time I could open up command prompt and start pinging to pin point the problem. I decided I would update the firmware to see if that would fix the issue. Since doing that the power light has been blinking non stop. I've tried restoring it to factory defaults by holding the reset button for 30seconds, turning it off for 2 minutes and back on. That little blue light just keeps flashing. I can't even access the router setting page using 192.168.1.1. My OS is Windows xp x64 sp2, and I have DSL.
View 9 Replies View RelatedMy router was working fine until today. I figured it out when I tried to get on the internet and it wouldn't let me. I hooked up the ethernet directly from my modem to my computer and then my internet worked fine.
View 4 Replies View RelatedI need fixing my router. I updated the firmware and it said the upload has failed ever since then:
-the router doesn't work
-blinking power light
-DMZ light doesn't turn on
-can't access 192.168.1.1
My router is a WRT54G v5
the power light on my wrt54g v2.2 router keeps blinking and it wont connect to the internet when connected, what should i do?
View 1 Replies View RelatedNo download available and none available via Linksys Live Chat or FTP and having spent the best part of the week trying to find relevant firmware on other forums I decided to come here to get answers to the following questions, hopefully from version 1.0 experienced owners or not.
#1. Can the firmware of version 2.0 and 3.0 be reduced to flash version 1.0?
#2. When diagnosing the blinking power light issue by connecting directly to the router and the network card using "ping -t 192.168.1.xxx" which network address do I use, 192.168.1.1 or 192.168.1.2 to 2xx?
I get a reply using 192.168.1.1 but I'm not sure that works when using the TFTP Utility if it's the wrong address on my Laptop to ping?
I have WRT 120 N which has apparently stopped working. When I turn it on, only the power led turns on without blinking, no other light flashes. My computer can't detect the router signals since the signal light is off. Neither does my modem show that the router is connected to it through the ethernet cable. My ethernet cable is working fine, since it is working directly with the computer.
View 6 Replies View RelatedI have a Linksys WRT54GS vers 7.2 Router on an iMac OS X Leopard. The other day I was in the middle of downloading an upgrade for the router when Firefox gave me this message: "Firefox can't find the server". I was no longer able to access the internet, and the router's green power light was left flashing. It flashed for over 24 hours. I tried unplugging the router and shutting down the computer, then plugging in the router and turning on the computer. (I don't have a modem.) The light was still flashing. I tried pressing the logo button for 5 seconds. Still flashing. Tried pressing the reset button in the back. Still flashing. 'I can't get on the internet or into the router. Linksys live chat gave me a link to "Upgrading the router’s firmware using the TFTP utility", which involves a download, but I can't download anything because I can't access the internet.
View 8 Replies View RelatedI've seen related to flashing power lights on the router involve fixes via firmware upgrades off a PC.I'm on an iMac os 10.6.7. The WRT54 used to work as a wireless modem a couple of years ago. Tonight, it doesn't. power light blinks. Can't access any webpage interface for the thing. Reset, power down, computer restart, cable modem turn off don't change anything. Is there anything that can be done other than tossing the linksys? If that is the only option, are there wireless routers more suitable for a Mac?
View 4 Replies View Relatedi have Linksys WRT610N V2 now i got problem the power light flashing still keep cannot use but wifi and wan and lan no light but 1 light power only still keep power flashing blinking no stable now i using adsl modem direct connected i using linksys am300 adsl modem
View 1 Replies View RelatedIf I conact from the modem to the pc I have internet so it must be the router. The power light is blinking along with all the port lights. Power light is blinking one time slow 2 fast. Have tried holding the reset button for 30 seconds and unpluging for 30 seconds. Can not go to the ip address it times out. New firmware is not avalible.
View 9 Replies View RelatedMy wireless router is WRT54GC ver2.0. When I plug the power cable, all the LED light blinking including the power LED light. I try to find the firmware in the website, but here only have the version 1.0.
View 9 Replies View RelatedI have a ~3 month old e1000 v2. In the last 24 hours it appears to have died, all 4 ethernet lights plus the power light and the one to it's left are on continuously. Before I dispose of it, does anyone know if this really is a hardware fail or is there some way to recover it? I've tried a few resets, power cycles and leaving it off for a few hours in the hopes that would bring it back to life but to no avail.
View 5 Replies View RelatedI have a Linksys E2500 and recently the power led light on the back of the router started blinking. The router itself seems to be working fine. I can access the router and the router seems to be assigning the IP addresses fine. I did look up the issue on the knowledge base and tried all the solutions but the light is still blinking. Not sure what to do anymore.
View 5 Replies View RelatedSo I just got this new WRT160Nv2 router. I have (1) wired computer and then my laptop running wireless to it. For the first couple days I had some issues getting consistant internet but after reading some stuff on here I downgraded to the version 8 hardware and it worked GREAT for about 3 days. Now my power light won't stop flashing and I have NO internet connection at all through the router. I have tried to reset the router by holding down the button and also unpluging it but still nothing.
View 9 Replies View RelatedI have a WRT300N and the power light is dim and all 4 ports are solid green along with the internet light being solid green.. Nothing else is plugged in.. Just the power.. I have tried to hard reset and nothing happens.
View 2 Replies View RelatedI just got the camera today, looks good, works good, at least so far.. BUT I was SURE this camera had a battery and charge function!? What's the point of having this camera if I can't place it say inside my car or in the garage (where it needs to be hidden, alas I can't use any cords!)?
View 5 Replies View RelatedI've got a number of 3502i's that I need to mount in a new classroom that does not have any ceiling (except the floor decking above). Ceiling is roughly 30-50' up. Contractors are going to run several 2" (or whatever we want) metal pipes from the ceiling down to a more reasonable level to mount the access points on and get below the hvac ducts/etc in the ceiling.
Problem is I can't find any bracket or mounting options for this! What are others using in this situation for mounting one of these access points onto a metal pipe such as this? I've checked Oberon Wireless, Terrawave and I don't see anything glancing through the product catalogs. Anyone mounting access points this way?
Everything was working fine. Changed Nothing on the router. Goes out and now wont broadcast a wireless signal, cant manually reset the router, or get into the settings with 192.168.1.1
Currently I am wired through it with my desktop and its working, but not much else.
So, I messed around with my router a little too much and just want to restore it back to the original firmware now. I have a WRT54GS v7 Linksys router and tried to follow this guide to flash the firmware to something a little more useful. After step 7 of that guide, I can't ping my router, can't access the GUI, and have no idea what my router's IP is. If I assign each computer plugged into the router an IP like 192.168.1.2 I can ping them, so the router is still functioning somewhat. I'm plugged into my modem right now to get on the Internet.
Right now, my power light is off, my DMZ light is off, my WLAN light is off, but the other lights turn on if I plug a cord into its port (plug a computer into port 1, port 1's light comes on). When I do an ipconfig /all i get this. I doubt the web interface still works, but if I could at least get the router's IP, couldn't I use tftp and put the firmware on that way?
1 =if its a rev 1c on the sticker that makes it DIR-615_REVC I am assuming
2= suddenly it shut down today yellow power lite , i cycled and nothing i reset then got a request to do a firmware update! I shut it down for a hour cycled and after a few minutes green power lite all my settings were still in place?I would think a reset would wipe this out.Its only 2 years old and would be surprised if its dieing.
My WAG120N power light is always red whenever plugged in. I can't access the configuration page. My adapter works fine and the Reset button doesn't work. I can't find any troubleshoot for the "red power light" problem in user manual !
View 3 Replies View RelatedI have a DIR-615 H/W ver C1.Suddenly everything stopped working. The D-Link light is green and the power light is amber, no other light is up (LAN or Internet).I've try to do a reset, no effect.Can't connect to the router even with a LAN cable (LAN lights stays dead with a working cable and computer plug-in).
View 3 Replies View RelatedI have a DIR-615 v e3 router
Did a bad dd-wrt flash and now all it does:
-no power light
-solid green lights: WAN-L1-L2-L3-L4
tried to go to recovery mode (power on while holding reset switch).....does not work.my search on the internet revealed, that after bad flash, power light still comes on, maybe as orange, maybe blinking, or just blinks once