I'd like to know if there's a command I can run to turn off paging on my SF302 switch. So for example, when I run the "show logging" command on the CLI, I'd like to it return all the results instead of prompting me to hit space bar or enter.
View 3 RepliesI'm wondering if anyone knows to set up the switch so that when I'm connecting via SSH, the switch doesn't prompt for a username if I supply one in the initial connect request? For example, we usually connect by typing something like the following at a command prompt:
ssh johndoe@10.10.10.10
Then the switch would prompt for a password. I've tried this on the Cisco SF302 but it still prompts for a username, and then the password.
Facing issue with 2960G switch , where its do not display "logging trap informational " in show running and show startup .where its showing all other levels from 0 to 5 and 7 after configuration and save commands. [code] after config getting saved , it do not shows in show runn or in show startup while for all other levels it do show the config lines .I tried the same on 12.55.SE release also but its same results . Is this a limitaion of this platform, is there any doc explaining the same for reference. [code]
View 1 Replies View RelatedWhat is the difference between SF302-08P and SF302-08MP Switches? Comparison Chart is identical.
View 1 Replies View RelatedI'm encountering what I think is an issue on logging system on FW ASA 5520 - Asa Version 8.4(2), ASDM version 6.4(5). When I disabled the logging inside a rule from ASDM, or from console with the "log disable" option inside ACL, If I check in ASDM logging real time window I continue to see all the entry related to disabled rules. This is a correct behaviour about ASA logging ? How I can "hide" the entry related to disabled rules (this is what I need for troubleshooting purposes) ?
View 1 Replies View RelatedI am running windows 7 HP. We have about 10 devices in one office and 5 devices connected thru a VPN..... When i hooked everything up 4 weeks ago I could see all the devices in the main office and the remote office connected thru the VPN (In the Network Folder that lists everything connected). Now I only see like 4 device and they are all in the main office.
I did some research a couple weeks ago and found a command prompt that "refreshed" all the devices that were connected, but now They are gone again and I cannot remember the command prompt!
Disable Prompt for password when computer resumesfrom standby for win 2003 serverunder
View 1 Replies View RelatedHow to get rid of Username Password prompt for VPN user connecting to computer with guest access on shared folders?If a VPN user types any word in the user name and hits enter without password, it gets in and sees shared folders, but I want this prompt to be disabled.
View 1 Replies View RelatedHow do I make the following work with Cisco 302-08G ? I have a 4-port Cisco wireless/wired router that allows for a guest account. I also have Cisco SF302-08 that I bought so I could use its port/vlan mirroring capability. How should I configure the network, given the aforementioned equipment, so that I can get a single point sniff.
Assume I have two wireless clients, one using the "regular" wireless SSID, and the other using the "guest" SSID. I can see 192.168.1.x (regular SSID) and 192.168.169.x (guest ssid) on the internet side (one the same physical cat5 of the wireless router. So far so good. But, I would like to use 302-08 to actually allow the guest SSID/network comm cable)unicate with the regular SSID/network. For example, if I ping 192.168.169.x from 192.168.1.x, I would like to see a response. Can I make them communicate properly with the 302-08 ?? if so, what do I need to do ?? (I will also have wired clients tied into the 302-08..so its important that it be the central sniffer point).
I am looking for the way how to disagle logging of one user. We are using one testing user for checking accesibility of ACS from large number of switches - this checking exhausting logs quite quickly. Is it possible to disable logging of such user?
View 2 Replies View RelatedI have the following setup using two SF302-08P PoE switches:
1st floor
=========
Switch #1 <-------> private network
<-------> public network
[Code].....
I have tried to make the config in switch #2 identical to switch #1, but something is still wrong. Is this most likely a VLAN setup problem, or what?
We are looking for a power adapter for a cisco switch Sf302-08p. We can't find the adapter anymore and we have to order a new one, but we can't figure out the order number of the adapter. The voltages is 48vdc and has an 4 pin connector . What is the type or ordernumber of this adapter?
View 1 Replies View RelatedMy syslog is full of %ASA-4-106023: Deny tcp src outside:---- by access-group "inbound-acl" messages. I did not configure an explict deny for the access list to log these denies.how I can disable logging of denied connections?
View 9 Replies View Relatedi am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues.
View 8 Replies View RelatedJust put in an SF302-08P switch with two AP541N's. Just a Comcast modem connects into the switch along with the two WAPs, nothing else. Speedtest through the cable modem with nothing plugged into it is 48Mbps. Then connecting a single laptop via the switch shows a speedtest of 33Mbps. Then with the two AP541N's plugged in and using the same laptop over WiFi, I'd consistently seen 10Mbps for downloading. But going right back to the cable modem directly showed me close to 50Mbps in a speed test.
Have factory defaults in all the Cisco devices, and poured over the settings and it looks like bandwidth limiting is disabled. Suspecting maybe it is for QoS and to optimize voice, but I see definite places in the devices where I could designate optimizing voice and those aren't enabled. Then started thinking with tweaking the wireless frequencies, but didn't want to do anything too unstable.
I am in the process of preping our network for the installation of an IP Camera based security system on it will be running within VLAN 600 in our network, and management would prefer that general users are not even aware it is there.
16 Cameras will all be running off two SF302-8P Switches that will be uplinked to our Cisco 2960 Access Switches. Due to port limitations I need to daisy chain the two SF302 Switches.
ACCESS-302-CA-01 - Ge1 uplinked to Port on ACCESS-03 (Cisco 2960) On this switch Fe1-8 Need to be in VLAN 600 to communicated with the camera server which will be plugged directly into Ge2 on Access 302-02.
ACCESS-302-CA-02 - Ge1 Uplinked to Ge2 on ACCESS-302-01
Ge2 - connected to the Network Video Recorder.
I've defined the VLAN's in the switch and have VLAN 600 as Untagged for FE1-8.
how do I configure Ge1 and Ge2 on each switch to pass the appropriate VLAN conntent to the devices connected?
Ask this question, if someone came across a 6513, one of the RJ45 ports are constantly falling.The question is how to disable logging on a specific portno logging event link-status does not work.
View 1 Replies View Relatedi am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues. Any support/reliability issues with this switch and the 7942s ?
View 3 Replies View RelatedI have several SG300-10 and SF302-08P switches running with L2-mode, and after I upgraded their firmware to 1.1.2.0, they began to record the following logs every one hour.
- Severity: Warning
- Description: %COPY-W-TRAP: The mirror-config file is illegal due to failure of previous copy operation/s to mirror-config.Also I found that I didn't see the Mirror Configuration file on the Configuration File Table in the Configuration Files Properties page.
Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones? They don't seem to be (a 7902G won't power on when connected to an SF302-08MP with firmware version 1.1). Is any special configuration needed on the switch to enable this detection?
View 2 Replies View Relatedknow Cisco IOS command, how to show when Catalyst 2960 was shut down (power off)?
View 2 Replies View RelatedWe have a design of two 6509 running in a VSS with dual supervisor each having fthree 10/100/1000mb etherner modules. We have diagnosed a wierd problem that none of the switchports in module 1 and 2 on either switches are having layer2/layer 3 connectivity.
Tried everything from changing the cables to changing the end device but no luck with it.
Module results show pass and no errors in the logging.
I have a cisco 2811 router set up as a nat/firewall gateway for my network. I've configured it for CBAC on using ip inspect and an access list.What I want is to use audit-trail to record network traffic (which means sending syslog messages to a server) concerning established sessions from my own network to locations in the outside. If i configure this using ip inspect audit-trail and no ip inspect alert-off, the configuration looks like this: [code] which works just fine, but there is the matter of icmp packets.
Since i use polling software that needs to check some machines in the outside part of the network, it is only natural that several icmp sessions are established through the Inspection Rule per minute. The problem is that since these sessions are recorded along with everything else, my syslogs are flooded with these (since i am using logging trap informational) to the point that more messages are generated about icmp than all other traffic combined, especially in non-working hours.What I am asking is a way for the audit-trail to be selecively disabled for icmp, so that the outgoing (echo) &incoming (echo reply) sessions can be established without generating syslog messages.
I have 30 switched in my corporate network it’s all up and running all switches running by default configuration and connected to WS-C4506 core switch our dhcp server pooling 192.168.100.1/27 network. Now we need to configure new Vlan for finance department this department has more than 200 users. If my server distributes 192.168.200.0 range ip can vlan2 automatically assign ip 200.0 addresses to finance department.All switches running default config no ip address assigned.
View 9 Replies View Relatedsometimes I let my friends to use my laptop but unfortunately they can see password of my wireless router which my laptop is connected to by going to this wifi network Properties and then to Security and then check in "Show Characters" box..so is there any way to prevent them from seeing my wifi network password in Windows 7?
View 1 Replies View RelatedI am using ACS5.2 I want user to access the device with all necessary command like show run/ver/int/log… I try to set user privilege using Shell from 1 to 10 but show run doesn't work.
View 15 Replies View RelatedIn our company we use the ACS 5.and i have a small problem, what we need to do is.create a profile that will allow SHOW RUNNING CONFIG but not configure terminal.i am investigating and im a littel bit lost i have created a new group but i dont see any option to put permissions.
View 1 Replies View Relatedis there a command available to run diagnostics in ASR port/SPA? the one below is from a juniper remote device. i was only able to find 'test interface' but haven't run this yet (currently in production).
View 5 Replies View Relatedi have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop : [code] I know that the solution would be to download a new valid image from tftp via the common prompt but what i don't undertand is why i cant access the rommon prompt.
View 5 Replies View RelatedI have a 2960S connected to an RSP 2300. The 2960S is currently running off of the RPS, and I would like to switch it back to the internal power supply. Can I just run "power supply 1 on"? Will this cause the switch to reboot? Also I am concerned because when I do a show env power it shows: [code]
Is it normal for the internal power supply to show Unavail when running off RPS?
I have upgraded my 7 x SG200 50/50 switches from 1.1.2.0 to 1.2.5.70 and after upgrading,most of these switches rebooted by itself while I'm saving or logging off. It gives me this error
View 7 Replies View RelatedI am trying to connect an SG200 to a customer's existing network. The customer does not want to receive any bpdu frames from the SG200. The customer's port has bpdu guard configured to err-disable their port upon receipt of a bpdu.
How do I completely disable spanning tree on the SG200 so that it does not send any bpdus?
I am thinking of buying a SG200-26P switch and have a few questions:Is it possible to disable the PoE function on the 12 PoE ports?I need al the ports but only 6 with PoE.What happens when you connect a non PoE device to a PoE port?
View 2 Replies View Related