I have the following setup using two SF302-08P PoE switches:
1st floor
=========
Switch #1 <-------> private network
<-------> public network
[Code].....
I have tried to make the config in switch #2 identical to switch #1, but something is still wrong. Is this most likely a VLAN setup problem, or what?
I am trying to set up a Vlan on an SF-302-08 small business switch. I would like two Vlans both with internet access but the two cannot communicate with each other. I am not really sure how to go about setting this up as its all fairly new to me. I have successfully set up the Vlans and the ports on each VLAN cannot communicate with each other however the internet access will only work when plugged into either VLAN but wont work on both together
View 1 Replies View RelatedI am in the process of preping our network for the installation of an IP Camera based security system on it will be running within VLAN 600 in our network, and management would prefer that general users are not even aware it is there.
16 Cameras will all be running off two SF302-8P Switches that will be uplinked to our Cisco 2960 Access Switches. Due to port limitations I need to daisy chain the two SF302 Switches.
ACCESS-302-CA-01 - Ge1 uplinked to Port on ACCESS-03 (Cisco 2960) On this switch Fe1-8 Need to be in VLAN 600 to communicated with the camera server which will be plugged directly into Ge2 on Access 302-02.
ACCESS-302-CA-02 - Ge1 Uplinked to Ge2 on ACCESS-302-01
Ge2 - connected to the Network Video Recorder.
I've defined the VLAN's in the switch and have VLAN 600 as Untagged for FE1-8.
how do I configure Ge1 and Ge2 on each switch to pass the appropriate VLAN conntent to the devices connected?
What is the difference between SF302-08P and SF302-08MP Switches? Comparison Chart is identical.
View 1 Replies View RelatedHow do I make the following work with Cisco 302-08G ? I have a 4-port Cisco wireless/wired router that allows for a guest account. I also have Cisco SF302-08 that I bought so I could use its port/vlan mirroring capability. How should I configure the network, given the aforementioned equipment, so that I can get a single point sniff.
Assume I have two wireless clients, one using the "regular" wireless SSID, and the other using the "guest" SSID. I can see 192.168.1.x (regular SSID) and 192.168.169.x (guest ssid) on the internet side (one the same physical cat5 of the wireless router. So far so good. But, I would like to use 302-08 to actually allow the guest SSID/network comm cable)unicate with the regular SSID/network. For example, if I ping 192.168.169.x from 192.168.1.x, I would like to see a response. Can I make them communicate properly with the 302-08 ?? if so, what do I need to do ?? (I will also have wired clients tied into the 302-08..so its important that it be the central sniffer point).
I'm trying to setup following scenario which is working with no issue on netgear switches (like GS108) but I have not been able to get it to work on Cisco SG-200 I did quite a bit of reading here on many post but nothing seems to work.
View 6 Replies View RelatedWe are looking for a power adapter for a cisco switch Sf302-08p. We can't find the adapter anymore and we have to order a new one, but we can't figure out the order number of the adapter. The voltages is 48vdc and has an 4 pin connector . What is the type or ordernumber of this adapter?
View 1 Replies View RelatedI would like to create 3 x VLANs on an SG 300-28P and have them completely isolated from each other, for example ports 1 - 12 on VLAN 1, ports 13 - 24 on VLAN 2 and ports 25 - 28 on VLAN 3. No communication between any of the VLANs.
Any simplest way to achieve this?
i am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues.
View 8 Replies View RelatedJust put in an SF302-08P switch with two AP541N's. Just a Comcast modem connects into the switch along with the two WAPs, nothing else. Speedtest through the cable modem with nothing plugged into it is 48Mbps. Then connecting a single laptop via the switch shows a speedtest of 33Mbps. Then with the two AP541N's plugged in and using the same laptop over WiFi, I'd consistently seen 10Mbps for downloading. But going right back to the cable modem directly showed me close to 50Mbps in a speed test.
Have factory defaults in all the Cisco devices, and poured over the settings and it looks like bandwidth limiting is disabled. Suspecting maybe it is for QoS and to optimize voice, but I see definite places in the devices where I could designate optimizing voice and those aren't enabled. Then started thinking with tweaking the wireless frequencies, but didn't want to do anything too unstable.
I'm wondering if anyone knows to set up the switch so that when I'm connecting via SSH, the switch doesn't prompt for a username if I supply one in the initial connect request? For example, we usually connect by typing something like the following at a command prompt:
ssh johndoe@10.10.10.10
Then the switch would prompt for a password. I've tried this on the Cisco SF302 but it still prompts for a username, and then the password.
i am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues. Any support/reliability issues with this switch and the 7942s ?
View 3 Replies View Relatedi have a question about the proper method to setup up vlan(s) on a sg200 switch with a sv220w router. Should i setup the vlan on the router or the switch? I have small office setup, i need atleast 2 vlans to separate the networks. i want both to have internet access but be completely isolated from each other.
View 5 Replies View RelatedI'm new to managed networking. So I'm having trouble understanding how to set up my switches properly. I have a closed network with about 20 switches and 2 IDF's. No router, and no internet. I have a SLM 2024 in want to have 4 ports set up with a VLAN. I have another SLM2024 I want to be on the same VLAN some where else. Switch 1 uses port 24 GBIC as and up link port to one of the IDF's. Switch 2 uses ports 12 and 24 copper(LACP) to make a hop from another switch(ports 1 and 13 LACP)which inturn is connected to the same IDF on port 24 GBIC. How do I set up switch 1 ports 7,8,19,20? Also, how do I set up switch 2 ports 7,8,19,20? VLAN 11
View 1 Replies View RelatedI have a dell powerconnect 2848 switch and setting up a vlan 3 an make port 1 mngt, port 48 uplink to layer 3 switch and tag vlan 1 and 3 to port 48 with cli commands for this setup. and also to untag ports 2-10 for computers
View 1 Replies View RelatedI'd like to know if there's a command I can run to turn off paging on my SF302 switch. So for example, when I run the "show logging" command on the CLI, I'd like to it return all the results instead of prompting me to hit space bar or enter.
View 3 Replies View RelatedI have several SG300-10 and SF302-08P switches running with L2-mode, and after I upgraded their firmware to 1.1.2.0, they began to record the following logs every one hour.
- Severity: Warning
- Description: %COPY-W-TRAP: The mirror-config file is illegal due to failure of previous copy operation/s to mirror-config.Also I found that I didn't see the Mirror Configuration file on the Configuration File Table in the Configuration Files Properties page.
Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones? They don't seem to be (a 7902G won't power on when connected to an SF302-08MP with firmware version 1.1). Is any special configuration needed on the switch to enable this detection?
View 2 Replies View RelatedI have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
View 5 Replies View RelatedWe are trying to config vlan 10 for data and vlan 20 for voice on the same port - port 1 of swtich SF300-24P to run both data and voice on different vlans.Do I have to add vlan 10 as an untagged vlan to port 1 and add vlan 20 as an tagged vlan to port 1?If I do not want to assign the native vlan 1 to port 1, how can I remove it ? The GUI page - assign VLAN to port does not allow to remove it.Aslo, what mode shall I set up on port 1? General, trunk or access ?
View 18 Replies View RelatedI have a Netgear GSM7248R switch with 5 different Vlans including th management Vlan. Each of the vlans are connected to my layer 3 switch for routing. I want to access the management vlan form any of my Vlans so my layer two switch can be detected by my snmp manager.
View 3 Replies View RelatedI have some problem in my small network.I have 2 SF-300 48 port switches and connected to 847 router for intervlan routing. I configure 7 vlan in SW1 and uplink to SW2 with trunkport.
The problem is that if i used default gateway for users ip address of interface (vlan interface) is ok. I bring two adsl modem and connected to vlan1 and vlan2 for internet access. When i connected this two modem vlan 1 and vlan 2 are not going to access other vlan 3,4,5,6,7 and wise versa.
vlan1 users getting default gateway from adsl modem ip, how i can permit this two vlan should to access other vlan 3,4,5,6,7 and 3,4,5,6,7 should access to internet also.
[URL]...
now we have 2 switches: SF300-24..on one SF300-24 we config it at layer 3 mode with VLAN configuration same as following [code] And we use port 26 on 2 switches SF300-24 is trunk mode then we connect both SF300-24 switches.But on SF300-24 layer 2 cann't inderstand VLAN from Sf300-24 layer 3..How to config VLAN on 2 switches SF300-24 Layer 3 and SF300-24 layer 2?
View 2 Replies View RelatedAny snmpset commands to add, modify and delete vlan table entries on SG300-10 switches? I checked url... however this information is apparently only valid for catalysts. The latest firmware is installed and the provided MIB files are used.
View 8 Replies View RelatedI'm going to have several SG300-28P switches to setup. I'll need to create multiple vlans for data, voice, and wireless traffic. I have the following questions in setting up this configuration:
VLAN 1 Management
VLAN 100 Data
VLAN 200 Wireless
VLAN 300 Voice
1) For managing the switches via IP, will LAN1 be the default management network? Should I create a seperate VLAN for managing the switches?
2) For uplinking the switches together, I plan to trunk a port to connect the switches together. What's the configuration on the trunk port to forward all vlans from one switch to another?
3) On some ports, I want to configure a trunk for two vlans (Data and Voice) where the phone has a pass through for PC. The phone supports tagging for the PC and the VoIP traffic. For example on port 10, would VLAN 100 and 300 be set to tagged?
I want to setup an home network with a wireless router and use multiple switches for wired connections through out my home. I currently have an Airport extreme hooked up to a cable modem and a leviton gateway hooked up to the Airport. The 2 computers connected to the Leviton are on a windows 7 homegroup and share fine, but won't share or discover any wireless device connected to Airport. My main goal is to have a wireless/wired network with all computers sharing information with each other. I want 2-3 wired switches/gateways with a min of 2 devices connected to each, connected to my wireless router whiich is connected to cable modem.
View 3 Replies View RelatedI've been reading this manual day in and out and can't figure it out. I think im getting Dell's & Cisco's Terminology mixxed up and that's why i can't get this switch to work.
I know my vlans work on my TZ210 ( sonicwall firewall) because they work on my dell managed switch, but now that i have my Cisco one, id like to setup my vlans on this..
If i can get one working i can do the rest.Trying to create vlan 50, iv'e created it but i don't know if i have done it correctly.
I have a Cisco RVS400 router at my restaurant. In lan ports 1-3 on the router, I have plugged in my point-of-sale computers.Into LAN port 4 I have plugged my wireless access point that is in my dining room.
The wireless access is there ONLY for the customers to access the internet. I want to make sure the customers cannot access my company data, can this be accomplished through the use of VLANs ? If so, how do I do this? All of my devices are configured for dhcp..if that's relevant.
setting up two VLANs for my WAP: one for all local network and internet traffic and one for just (guest) internet traffic. I just purchased both devices but I don't know if I have the option for free Cisco phone support.
View 1 Replies View RelatedI am looking to set-up an isolated WLAN for the users in my organization and how to proceed What I have is the following
Cisco 5508 Wireless LAN controller
Cisco Catalyst 3750 24 port (not sure what exact model)
Cisco AIR-AP1131AG-A-K9 POE Access Point
Cisco ASA 5510
Currently what I would like to do is to setup a VLAN on the Cisco ASA 5510, connect the Catalyst to the VLAN and connect the 5508 Wireless LAN to the Catalyst via Fibre. From there on in - I would connect each AP to the Catalyst? The proposed scenario is that the VLAN would be in a DMZ and have direct access to the Internet without any filtering and users would connect their devices to the AP and get a DHCP address and be able to surf with freedom?The problem is - I am unsure as of where to start. I have been certified Cisco in 2001, however I havent started to use my skills until now.The Vlan would be the following: 192.168.20.X
I have a general networking question regarding VLANS, multiple broadband connections and accessing PC's on both setups from each other.What I would like to do is have 2 broadband connections, one a cable connection and one a DSL connection. I would like to run them both through a Netgear FS-726T switch. Since the cable connection will go through a Linksys router giving out I.P.s in the range of 192.168.1.x and the DSL will probably use the same range, I would like to keep specific PC's connecting through the DSL connection and some other PC's specifically through the cable connection. I THINK that this can be done via the use of VLAN's set up on the Netgear switch but I am unfamiliar with setting them up. I've read through the manual and researched it online but I must be missing something.Due to the bandwidth limitations on the Comcast connection, I would like to avoid any data coming from the PC's on the DSL connection from going out through the cable connection (I do customer support for my business and want customers to be able to access files on my file server and also be able to back up their PC's online to my backup server but on the DSL connection. I will eat up my cable bandwidth in a hurry just from the backups alone. I would like to set up all the PC's with static I.P. addresses if possible. Now, I also need to be able to remotely access any of the PC's from outside my network (which I can do now) but I need to be able to access the cable connected PC's from the DSL connected PC's and vice versa.I have a feeling what I want to do is a mess and may not even be feasible. I have asked the networking personnel where I work but (primarily because they are arrogant SOB's) they won't even give me the slightest bit of information.
View 1 Replies View RelatedTrying to work out if I can setup a VLAN interface on a 1721 router.The only interfaces that are listed are the Ethernet (W1-ENET) and the Fast Ethernet interface.I'm still super new to all of this and learn how to change IOS via rommon and TFTP after realizing I had an IOS too large for the memory?
View 3 Replies View RelatedI have a RVS4000 and I am going to configure vlan in the near future. Among all other configurations sent by the internet provider company is this one :
Firewall NAT :
from x.x.2.0/24 to 0.0.0.0/24 should be NAT
from x.x.2.0/24 to x.x.0.0/21 should not be NAT
From all the other configurations, this one is not clear to me. Can this configuration be done on a RVS4000 and where can it be done.