setting up two VLANs for my WAP: one for all local network and internet traffic and one for just (guest) internet traffic. I just purchased both devices but I don't know if I have the option for free Cisco phone support.
View 1 RepliesI have a dell powerconnect 2848 switch and setting up a vlan 3 an make port 1 mngt, port 48 uplink to layer 3 switch and tag vlan 1 and 3 to port 48 with cli commands for this setup. and also to untag ports 2-10 for computers
View 1 Replies View RelatedI'm looking to setup Inter-VLan routing on a 4800G switch.
I'm looking for all workstations (VLAN1) to be able to talk to the windows network (VLAN2) and to our Novell network (VLAN3)
but I don't want Windows (VLAN2) and Novell (VLAN3) talking to each other. Is this possible accross a single switch? I have 7 switches available to use if needed.
I have been looking for a new router that can handle intensive bandwidth for my office which can handle vlans, QoS, bandwidth management, VPN/VPN Passthrough, and perhaps multi-WAN/Load Balance. A friend has recommended the Mikrotik RB 1200 for my application, having looked at the product the feature set seems to be quite extensive and the price point is very attractive. The router is also rack mountable (a big plus!!!), my question is wether the router is relatively easy to configure/manage. I have managed/installed other routers such as the Cisco SMB series but I have no experience with Mikrotik. I am very tech savvy and have a moderate knowledge of network infrastructure. I have heard so may different responses to the simplicity and I would like y'all to weigh in before I purchase the router. (OR WHATEVER RACKMOUNTABLE ROUTERS YOU RECOMMEND FOR SMB)
View 10 Replies View RelatedIs it possible to setup a Cisco 1200 AP with 802.1x to drop users into the corprate network if they have a certificate or if not to put them on the guest network?
View 3 Replies View RelatedI am trying to set up a Vlan on an SF-302-08 small business switch. I would like two Vlans both with internet access but the two cannot communicate with each other. I am not really sure how to go about setting this up as its all fairly new to me. I have successfully set up the Vlans and the ports on each VLAN cannot communicate with each other however the internet access will only work when plugged into either VLAN but wont work on both together
View 1 Replies View RelatedI have two networks at two sites with a dot1q trunk between the two L3 switches at both sites (no routers involved)
SITE A - Cisco 3750 L3 - VLAN ID 50
10.10.50.0/24
SITE B - Cisco 3750 L3 - VLAN ID 50
10.20.50.0/24
I would like to extend the SITE A VLAN to SITE B so that I can move hosts from SITE A to SITE B without needing to change their IP address but the vlan ID is already in use. Obviously the easy solution is to change the VLAN ID for one or other of the sites but both sites contain hosts that run 24/7. Is there a way to join two VLANs with different IDs together.So for example I create a new VLAN 60 at SITE B and associate it with VLAN 50 at SITE A.
I've been reading this manual day in and out and can't figure it out. I think im getting Dell's & Cisco's Terminology mixxed up and that's why i can't get this switch to work.
I know my vlans work on my TZ210 ( sonicwall firewall) because they work on my dell managed switch, but now that i have my Cisco one, id like to setup my vlans on this..
If i can get one working i can do the rest.Trying to create vlan 50, iv'e created it but i don't know if i have done it correctly.
I'm trying to setup following scenario which is working with no issue on netgear switches (like GS108) but I have not been able to get it to work on Cisco SG-200 I did quite a bit of reading here on many post but nothing seems to work.
View 6 Replies View RelatedI have a Cisco RVS400 router at my restaurant. In lan ports 1-3 on the router, I have plugged in my point-of-sale computers.Into LAN port 4 I have plugged my wireless access point that is in my dining room.
The wireless access is there ONLY for the customers to access the internet. I want to make sure the customers cannot access my company data, can this be accomplished through the use of VLANs ? If so, how do I do this? All of my devices are configured for dhcp..if that's relevant.
I have the following setup using two SF302-08P PoE switches:
1st floor
=========
Switch #1 <-------> private network
<-------> public network
[Code].....
I have tried to make the config in switch #2 identical to switch #1, but something is still wrong. Is this most likely a VLAN setup problem, or what?
I am looking to set-up an isolated WLAN for the users in my organization and how to proceed What I have is the following
Cisco 5508 Wireless LAN controller
Cisco Catalyst 3750 24 port (not sure what exact model)
Cisco AIR-AP1131AG-A-K9 POE Access Point
Cisco ASA 5510
Currently what I would like to do is to setup a VLAN on the Cisco ASA 5510, connect the Catalyst to the VLAN and connect the 5508 Wireless LAN to the Catalyst via Fibre. From there on in - I would connect each AP to the Catalyst? The proposed scenario is that the VLAN would be in a DMZ and have direct access to the Internet without any filtering and users would connect their devices to the AP and get a DHCP address and be able to surf with freedom?The problem is - I am unsure as of where to start. I have been certified Cisco in 2001, however I havent started to use my skills until now.The Vlan would be the following: 192.168.20.X
I would like to create 3 x VLANs on an SG 300-28P and have them completely isolated from each other, for example ports 1 - 12 on VLAN 1, ports 13 - 24 on VLAN 2 and ports 25 - 28 on VLAN 3. No communication between any of the VLANs.
Any simplest way to achieve this?
I have a general networking question regarding VLANS, multiple broadband connections and accessing PC's on both setups from each other.What I would like to do is have 2 broadband connections, one a cable connection and one a DSL connection. I would like to run them both through a Netgear FS-726T switch. Since the cable connection will go through a Linksys router giving out I.P.s in the range of 192.168.1.x and the DSL will probably use the same range, I would like to keep specific PC's connecting through the DSL connection and some other PC's specifically through the cable connection. I THINK that this can be done via the use of VLAN's set up on the Netgear switch but I am unfamiliar with setting them up. I've read through the manual and researched it online but I must be missing something.Due to the bandwidth limitations on the Comcast connection, I would like to avoid any data coming from the PC's on the DSL connection from going out through the cable connection (I do customer support for my business and want customers to be able to access files on my file server and also be able to back up their PC's online to my backup server but on the DSL connection. I will eat up my cable bandwidth in a hurry just from the backups alone. I would like to set up all the PC's with static I.P. addresses if possible. Now, I also need to be able to remotely access any of the PC's from outside my network (which I can do now) but I need to be able to access the cable connected PC's from the DSL connected PC's and vice versa.I have a feeling what I want to do is a mess and may not even be feasible. I have asked the networking personnel where I work but (primarily because they are arrogant SOB's) they won't even give me the slightest bit of information.
View 1 Replies View RelatedTrying to work out if I can setup a VLAN interface on a 1721 router.The only interfaces that are listed are the Ethernet (W1-ENET) and the Fast Ethernet interface.I'm still super new to all of this and learn how to change IOS via rommon and TFTP after realizing I had an IOS too large for the memory?
View 3 Replies View RelatedI have a RVS4000 and I am going to configure vlan in the near future. Among all other configurations sent by the internet provider company is this one :
Firewall NAT :
from x.x.2.0/24 to 0.0.0.0/24 should be NAT
from x.x.2.0/24 to x.x.0.0/21 should not be NAT
From all the other configurations, this one is not clear to me. Can this configuration be done on a RVS4000 and where can it be done.
So I've got an odd issue here, have an older 4948 that I'm trying to setup on our management vlan so i can manage it from another host connect to the switch. I can't figure out why its not working. Below is the config
vlan is 64 and all the trunk and access ports that are on vlan 64 are working just fine. Just can't hit the switch from a machine on the 64 vlan.
!
interface Vlan1
no ip address
[Code].....
I am using an SRP541W router and i am trying to configure 2 vlans, each one to use its own Wan:Here are the dhcprules and vlans:As can be seen, each one has its own wan interface.
Vlans:As can be seen, each vlan is using its own ports and dhcp rule, so, now they should be separate.
Both Wans are connected: So now (at least as i see things) the two vlans are separate and using different Wan. But the reality is different, everything is going out using Wan1.Also in the Interface Info you can see that the 2 vlans are listed under the Wan1.
The rest of router setting are default.
I am extremely new to network but also excited with the things you can achieve with a Cisco switch.For about 3 months I sat down looking at my "Cisco C2950-24 Switch", this surely for such a beastly looking thing it must be able to do something other than just allow you to plug in cables. So with that said I started to do some reading and watched a couple of You Tube Videos.I am on the route to complete my first goal and thats have my own VLAN setup with 1 Server and 6 clients. The Server is running ESXi therefore a few other servers are running inside it too.So my VLAN - VLANID 20 running the network 172.22.22.0. On the physical switch I have the following:Port 1 - WAN incoming connection from my Router on the network 192.168.178.0Port 2 thru 9 all running on VLAN 20.By the way I am using the GUI Cisco Network assistant
View 4 Replies View RelatedI am trying to set up VLAN on my cisco router, where do i check for the setting for creating a VLAN on my Wireless AP. Is it possible on this model.
View 1 Replies View RelatedI am running a /24 network in Active Directory with my ASA acting as gateway and firewall. Standard interfaces (Ethernet 0/0 as outside, Ethernet 0/1 as inside)
As of now I have no VLans set up, but I need to setup wireless Internet access for guests... I need directions on how to setup a Vlan with its on DHCP for these aguests... I can then make sure that my APs can be pointed to the same VLAN... I am not familiar with CLI, have generally used ASDM. I am currently running ASDM 6.3(1) on an ASA with version 8.3(1).
This is something I need to do quickly as we are expecting 20-40 "guests" shortly, and I don't want them to use our internal DHCP server addresses.
i have a question about the proper method to setup up vlan(s) on a sg200 switch with a sv220w router. Should i setup the vlan on the router or the switch? I have small office setup, i need atleast 2 vlans to separate the networks. i want both to have internet access but be completely isolated from each other.
View 5 Replies View RelatedJust trying to figure out how LAP manage clients in a h-reap setup.Have a setup with native vlan on 144 (switch and AP) and ssid tagging in other vlan... Got this on switch:
Jan 12 10:31:43.121: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0811.9695.9b04 on port FastEthernet0/42.
Jan 12 10:31:43.121: %PORT_SECURITY-2-PSECURE_VIOLATION_VLAN: Security violation on port FastEthernet0/42 due to MAC address 0811.9695.9b04 on VLAN 144
Jan 12 10:37:42.770: %PORT_SECURITY-2-PSECURE_VIOLATION: Security violation occurred, caused by MAC address 0811.9695.9b04 on port FastEthernet0/42.
Jan 12 10:37:42.770: %PORT_SECURITY-2-PSECURE_VIOLATION_VLAN: Security violation on port FastEthernet0/42 due to MAC address 0811.9695.9b04 on VLAN 144
Wonder why clients MAC is seen on native vlan (and ofcourse also on taged vlan) ...?
I'm new to managed networking. So I'm having trouble understanding how to set up my switches properly. I have a closed network with about 20 switches and 2 IDF's. No router, and no internet. I have a SLM 2024 in want to have 4 ports set up with a VLAN. I have another SLM2024 I want to be on the same VLAN some where else. Switch 1 uses port 24 GBIC as and up link port to one of the IDF's. Switch 2 uses ports 12 and 24 copper(LACP) to make a hop from another switch(ports 1 and 13 LACP)which inturn is connected to the same IDF on port 24 GBIC. How do I set up switch 1 ports 7,8,19,20? Also, how do I set up switch 2 ports 7,8,19,20? VLAN 11
View 1 Replies View RelatedI have a Cisco 3845 Integrated Service Router and I have installed a Service Module. I want to use the integrated Gigabit ports as switch ports and put ports in the Service Module and Gigabit port in a VLAN.
Is this possible? can it be done by setting internal Gigabit link as trunk and how? Below is the somewhat the setup i am looking for
Service module
fa0/1 |
fa0/2 | Vlan X
fa0/3 |
[Code]....
I have registered here to clarify some things about VLAN's. There are so many (different) names and mentions that i found tat my vision gets blurry looking through all the info.I have a setup at a client where the Guest WiFi access needs to be separated from the normal LAN where all the normal devices are attached to. The guests are not allowed to reach the IP camera's and printer etc. etc. . I am trying to visualize how the traffic should flow but the Tagged, Untagged, PVID, Trunks and other names that i found make it difficult for me to see how it works together.
View 8 Replies View RelatedI have a Cisco RV180-K9-NA router. I would like to set up 2 separate VLAN assigned to different ports on the router. I will be using LAN port #1 to communicate with the router. The NIC connecting the PC to the router has multiple IP addresses assigned to it so that I can communicate with the separate VPNs (192.168.1.x for the router; 172.16.10.x for VLAN #1 on port 2; and 182.16.10.x for VLAN #2 on port 3). I also need to be able to have the router provide both IPv4 and IPv6 DHCP services for devices on each subnet.
View 3 Replies View RelatedI have 2 SG300 switches, in layer3 mode, lag'd together for high availability, serving 2 Dell R815's and a Dell Equallogic 4100 for virtualisation. I have setup a number of vlan's, network traffic, mgmnt traffic, iScsi, vMotion etc and they seem to work.
However, Equallogic unit suddenly became unavailable to view for managment yet maintained iscsi traffic for the servers ok. After much head scratching, noticed that one of my SG300's had the vlan ports assigned to various vlans had *automagically* changed there assignment, ie tagged changed to excluded, but only for one of the iscsi traffic connections and the mgmnt port, both coming from the Equallogic, the other iscsi continued its assignment fine. The other SG300 hasn't changed. Guaranteee no one has been into change it and no changes have been made to Dell servers or Equallogic.
Q. Is there any circumstance where the switch can change the port setup itself? or is there any external circumstance that would trigger that change either?
This has now occured twice. The setup is running as a test lab, not in production until all setup is complete, then it will replace our existing harware.
I need to setup a vlan between the 6509 and 2621 router. This needs to be a VLAN (200) the runs between the devices that uses DOT1Q trunking. The end result is all the networks (vlans) on the 6509 can talk to the LAN on the 2600 (10.133.22.0 / 23) and visa versa.
Device 1
6509 with CatOS / IOS
Config I did on the MSFC:
Interface Vlan 200
ip address 10.10.10.1 255.255.255.248
[code]....
I am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies View RelatedI have a Dell switch setup with 2 Vlan's. Vlan 1 is to the network. Vlan 20 is going to be for wireless access to the internet. How do I configure the switch/router so that Vlan 20 only connects to the internet and not the network? I will later want to have a 2nd SSID that I want to connect to both the internet and network.
View 5 Replies View RelatedFor test I used 2 Switch that name "ESW X" and "ESW Y" I have 2 network that I named "Network A" and "Network B" I build 2 VLAN for each network that named Vlan 2 for Network A and Vlan 3 for Network B, I don't use Vlan 1 because it's the default Vlan
Configuration ESW X:
port e1 : ACCESS PORT on UNTTAGGED Vlan 2
port e2 : ACCESS PORT on UNTTAGGED Vlan 2
port e3 : ACCESS PORT on UNTTAGGED Vlan 3
port e4 : ACCESS PORT on UNTTAGGED Vlan 3
port g3 : TRUNK PORT with UNTTAGGED Vlan 1(default) and TAGGED Vlan 2 and Vlan 3
[code]....
Each Vlan can't communicate between the two switch, I think they're a problem in my vlan/port configuration?
i'm using an rv220W and i whant to know if is it possible to assign vpn traffic to a vlan when i setup an ipsec tunnel?
example:
Im using different vlans on my rv220W.
Vlan 10: engineers (ex: 192.168.1.0/27) no intervlan routing
Vlan20: sales (ex: 10.0.123.0/24) no intervlan routing
This is what i need: - An engineer is on the road and when he makes a ipsec vpn connection => assignd to the vlan "engineers" so he can access the server/pc's in that vlan.and when someone from the sales group starts a vpn connection he needs to be in the vlan "sales" so he can access his pc/data,...