Cisco Switches :: SF302 - Ssh Prevent Prompt For Password
Oct 3, 2012
I'm wondering if anyone knows to set up the switch so that when I'm connecting via SSH, the switch doesn't prompt for a username if I supply one in the initial connect request? For example, we usually connect by typing something like the following at a command prompt:
ssh johndoe@10.10.10.10
Then the switch would prompt for a password. I've tried this on the Cisco SF302 but it still prompts for a username, and then the password.
View 7 Replies
ADVERTISEMENT
Nov 14, 2012
I'd like to know if there's a command I can run to turn off paging on my SF302 switch. So for example, when I run the "show logging" command on the CLI, I'd like to it return all the results instead of prompting me to hit space bar or enter.
View 3 Replies
View Related
May 22, 2011
What is the difference between SF302-08P and SF302-08MP Switches? Comparison Chart is identical.
View 1 Replies
View Related
Apr 6, 2012
How do I make the following work with Cisco 302-08G ? I have a 4-port Cisco wireless/wired router that allows for a guest account. I also have Cisco SF302-08 that I bought so I could use its port/vlan mirroring capability. How should I configure the network, given the aforementioned equipment, so that I can get a single point sniff.
Assume I have two wireless clients, one using the "regular" wireless SSID, and the other using the "guest" SSID. I can see 192.168.1.x (regular SSID) and 192.168.169.x (guest ssid) on the internet side (one the same physical cat5 of the wireless router. So far so good. But, I would like to use 302-08 to actually allow the guest SSID/network comm cable)unicate with the regular SSID/network. For example, if I ping 192.168.169.x from 192.168.1.x, I would like to see a response. Can I make them communicate properly with the 302-08 ?? if so, what do I need to do ?? (I will also have wired clients tied into the 302-08..so its important that it be the central sniffer point).
View 2 Replies
View Related
Feb 6, 2013
I have the following setup using two SF302-08P PoE switches:
1st floor
=========
Switch #1 <-------> private network
<-------> public network
[Code].....
I have tried to make the config in switch #2 identical to switch #1, but something is still wrong. Is this most likely a VLAN setup problem, or what?
View 3 Replies
View Related
Dec 27, 2012
We are looking for a power adapter for a cisco switch Sf302-08p. We can't find the adapter anymore and we have to order a new one, but we can't figure out the order number of the adapter. The voltages is 48vdc and has an 4 pin connector . What is the type or ordernumber of this adapter?
View 1 Replies
View Related
Oct 22, 2012
i am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues.
View 8 Replies
View Related
Aug 9, 2012
Just put in an SF302-08P switch with two AP541N's. Just a Comcast modem connects into the switch along with the two WAPs, nothing else. Speedtest through the cable modem with nothing plugged into it is 48Mbps. Then connecting a single laptop via the switch shows a speedtest of 33Mbps. Then with the two AP541N's plugged in and using the same laptop over WiFi, I'd consistently seen 10Mbps for downloading. But going right back to the cable modem directly showed me close to 50Mbps in a speed test.
Have factory defaults in all the Cisco devices, and poured over the settings and it looks like bandwidth limiting is disabled. Suspecting maybe it is for QoS and to optimize voice, but I see definite places in the devices where I could designate optimizing voice and those aren't enabled. Then started thinking with tweaking the wireless frequencies, but didn't want to do anything too unstable.
View 2 Replies
View Related
Mar 13, 2012
I am in the process of preping our network for the installation of an IP Camera based security system on it will be running within VLAN 600 in our network, and management would prefer that general users are not even aware it is there.
16 Cameras will all be running off two SF302-8P Switches that will be uplinked to our Cisco 2960 Access Switches. Due to port limitations I need to daisy chain the two SF302 Switches.
ACCESS-302-CA-01 - Ge1 uplinked to Port on ACCESS-03 (Cisco 2960) On this switch Fe1-8 Need to be in VLAN 600 to communicated with the camera server which will be plugged directly into Ge2 on Access 302-02.
ACCESS-302-CA-02 - Ge1 Uplinked to Ge2 on ACCESS-302-01
Ge2 - connected to the Network Video Recorder.
I've defined the VLAN's in the switch and have VLAN 600 as Untagged for FE1-8.
how do I configure Ge1 and Ge2 on each switch to pass the appropriate VLAN conntent to the devices connected?
View 1 Replies
View Related
Nov 8, 2011
i am looking at quoting the SF302-08P for a client which will have three small offices interconnected via single mode fiber. I am planning on connecting them to a 3560 switch. Each office will have no more than 3 - 7942 phones. I reviewed the notes on this switch and it seems it should support this phone type without any issues. Any support/reliability issues with this switch and the 7942s ?
View 3 Replies
View Related
Jan 21, 2012
I have several SG300-10 and SF302-08P switches running with L2-mode, and after I upgraded their firmware to 1.1.2.0, they began to record the following logs every one hour.
- Severity: Warning
- Description: %COPY-W-TRAP: The mirror-config file is illegal due to failure of previous copy operation/s to mirror-config.Also I found that I didn't see the Mirror Configuration file on the Configuration File Table in the Configuration Files Properties page.
View 6 Replies
View Related
Jul 6, 2011
Are 300 Series switches compatible with pre-standard PoE detection in old Cisco phones? They don't seem to be (a 7902G won't power on when connected to an SF302-08MP with firmware version 1.1). Is any special configuration needed on the switch to enable this detection?
View 2 Replies
View Related
Feb 15, 2012
How do I change my password to prevent unauthorized access by other people?
View 2 Replies
View Related
Apr 11, 2013
I work in a lab testing interoperability between Avaya and Cisco VoIP products.I am setting up an environment to test Avaya 96x1 phones with VPN using SCEP going thru an ASA 5510 to a backend IP PBX.
Environment: Windows Server 2008 R2, Enterprise Edition, AD with DNS, NDES Cisco ASA 5510 running 9.0(1)
I would like to setup certificate enrollment between a Windows Server 2008 R2 and a Cisco ASA 5510. Here are the commands that I use for the Cisco ASA 5510:
crypto key generate rsa modulus 2048 crypto ca trustpoint ASA5510-trust enrollment url http://10.129.112.20/certsrv/mscep/mscep.dll enrollment retry period 5 enrollment retry count 3 password Interop123 exit crypto ca authenticate ASA5510-trust crypto ca enroll ASA5510-trust
Everything works as expected until I try to enroll. There is no prompt for the enrollment password and the certificate request is denied.
ciscoasa(config)# crypto ca enroll ASA5510-trust%% Start certificate enrollment ..% The fully-qualified domain name in the certificate will be: ciscoasa.avayasil.avaya.com% Include the device serial number in the subject name? [yes/no]: NoRequest certificate from CA? [yes/no]: yes% Certificate request sent to Certificate Authorityciscoasa(config)# The certificate enrollment request was denied by CA!
Why isn't there a prompt for the enrollment password?BTW, If I set "enforcepassword" to "0" in the Windows registry, then it works.
View 1 Replies
View Related
Dec 4, 2012
How to find the password through lan or cmd
View 2 Replies
View Related
Jan 30, 2013
I'm using netgear cg3000d and i want to change my password. But my default gateway IP doesn't prompt a log in, only an error message.
I've tried restoring the browser to presettings, clearing the cache, and using chrome, and firefox.
I think i should be logging into admin gui for the router
View 1 Replies
View Related
Feb 6, 2013
I recently configured a cisco 3750 switch for a stand alone network here at work, and on all our other switches and routers we use ACS to access everything. This switch being a stand alone I dont have that option.
So being like that I have to create everyone in the shop a username and password. Is there a way to prompt the user to change their password on their first login like you would with windows or such?
View 1 Replies
View Related
Dec 21, 2012
We currently have a client that uses the IPSec VPN Client to remote in to their PIX 501. When they connect, it secures communication and immediately connects/minimizes and the tunnel-group name/password is sufficient so no prompt for a username/password from a local/radius database.
When setting this up on a newly purchased ASA, a username/password is prompted every time they try to connect. Is there a way to eliminate this feature or a command in the tunnel-group or group policy so that a username/password is not required after the connection profile establishes the VPN? It is ASA 8.4.
View 2 Replies
View Related
Feb 17, 2012
I know a little bit about computers but I am having problems trying to connect to the internet that I cannot figure out. I connected the Ethernet cable to the back, it lit up, but it still says Local area connection doesn't have a valid IP configuration.
View 1 Replies
View Related
Jan 29, 2013
I have a ASA 5520 which is intended to use as a VPN for clients using PDA, I think the PDA is a very old product that the VPN only support CHAP/ MS- CHAP, but seems it cannot connect the VPN, it will prompt "invalid username and password" (but in fact the username and password is valid when using PAP), below is the log i captured from the ASDM when the PDA is connecting the VPN. when i tried to connect it in windows PC, I also have the same issue if the VPN setting is using MS-CHAP, if I choose PAP, it can connect with no problem. But the PDA has no option of PAP. [code]
View 0 Replies
View Related
Jan 9, 2011
I just purchased a used 1242AG which is running Version 12.4(13d)JA.I tried the mode button on power on holding for 2-3 seconds, but nothing happens and Cisco/Cisco login does not work. I have figured out if I hold the mode button in for 30 seconds while powering up I get an AP prompt.I tried doing a dir flash but get permission denied.Is their any commands I can run at AP prompt to attempt to reflash this unit or reset password somehow?
View 7 Replies
View Related
Jan 12, 2011
How do configure win2008 server to bring up a password prompt box when access via a workgroup pc on lan.
View 1 Replies
View Related
Apr 25, 2011
Disable Prompt for password when computer resumesfrom standby for win 2003 serverunder
View 1 Replies
View Related
May 5, 2012
How to get rid of Username Password prompt for VPN user connecting to computer with guest access on shared folders?If a VPN user types any word in the user name and hits enter without password, it gets in and sees shared folders, but I want this prompt to be disabled.
View 1 Replies
View Related
Apr 12, 2011
For weeks guest access to my e3000 worked fine. Today I have a friend come over, his XP connects to the guest wi-fi, but his computer does not get a prompt for a password.
View 6 Replies
View Related
May 5, 2011
Currently in my office have a TPlink wireless router (WR1043N), and Dlink 615 router.Below is my office's network organization.Internet-->TPLinkRouter(192.168.2.0)-->DlinkRouter(192.168.0.0)We want to host a demo website but we are afraid our network being attacked. So we wish to implement a DMZ network to hide our internal network from outside. My question is can i setup a dmz network with the above capabilities by using home routers?
View 5 Replies
View Related
May 2, 2012
i have recently tried to change the catos on a Catalyst 2948G-L3 and since then i have the following message in a loop : [code] I know that the solution would be to download a new valid image from tftp via the common prompt but what i don't undertand is why i cant access the rommon prompt.
View 5 Replies
View Related
May 7, 2012
I am trying to use a SF302-08P switch to connect a conference phone (Cisco 7937) to my infrastructure. I connected the G2 port on the SF302 to a Gig copper port on the Catalyst. I configured both ports as trunked ports and port e1 on the SF302 as an access port for the phone. VLAN 1 is the default VLAN and VLAN 10 for voice. However, the phone does not connect to the Call Manager. I have changed the configurations on the G2 trunked port and the ethernet port (trunked ports, general ports, tagged and untagged). I have also changed the configuration on the Ethernet port (general, access, trunk, set it on the default VLAN, in the voice VLAN, etc.) The SF302 connects to the Catalyst, and PCs connect OK.
View 4 Replies
View Related
Feb 19, 2012
For a customer of mine I've installed 8 WAP 200 access points with an SF302 switch. The Access point are powered with POE. All seems to function properly: the clients are simple Android device and the connection appears solid.. We've a good roaming between access points (not seamless of course but is ok) and no particalur problems, also because the network is used to drive very LOW data (no internet): the clients opens a tcp connection to the server and sends only a keep alive packets over this connection.. Then sometime the server send a very small amount of data (some byte) to activate the display of the device and show a question.. the clients reply with some other byte of data and so on.. During an event of 3/4 hour we can do this 12/14 times, so the network load is nearly 0....
Last night the system suddenly stopped working: ALL clients (300) lost connection from their access points at the same time! How this can happens? The only reason that I can imagine is a power loss on the switch...
View 1 Replies
View Related
Oct 15, 2012
I want to connect a Cisco small business switch (sf302-8) to a Cisco catalyst 2960S over a multi mode fiber. The transceiver I am using in the catalyst is a GLC-SX-MM. I presume in the SF302, I will have to use a MGBSX1. My question is "are these transceiver compatible with each other and if not, is there a transceiver that will suit both pieces of hardware?
View 2 Replies
View Related
Oct 4, 2011
I need to know if there is a password recovery procedure on a switch ESW 520
View 2 Replies
View Related
Oct 17, 2012
I have been asked to do a network survey at a client. They are using the Cisco SGE2000 switch, which is new to me (used to working with 3750 switches). They seem to have lost the username/pasword for one the switches. Is there an way to recover from this, without reseting the whol config (not sure they even have a backup) ..
View 1 Replies
View Related
Nov 17, 2012
We have a mitel 3300 PBX that is our DHCP server. It feeds an old Foundry Networks switch that nobody knows the password for anymore so I can't even look in it to get some clues. What I think I know is this.
vlan1 = PC's subnet 10.0.0.X 255.255.255.0
vlan2 = phones subnet 10.1.0.X 255.255.255.0
Phones plug into the switch, PC's plug into the phone.
I am assuming this to be the case becase all the PC's get those numbers and when booting up a phone it comes up and says "vlan2 pri 5" during the DHCP discovery.
Like I said the Mitel 3300 is the DHCP server and our internet access is from the firewall's trusted port.
I have put the switch in L3 mode via the console. No matter what I try, the PC will always get IP addresses in vlan2's subnet. Even if I plug the PC directly into the switch.
I have factory reset this baby and all I have done at this point is put it back in L3 and changed the default ip address so I can get to the web GUI.
View 9 Replies
View Related
