Cisco WAN :: 7609 Configuration Check On Particular Device
Feb 4, 2012
Yesterday, myself and local support team has been engaged to perform troubleshooting the issue of some web site accessing .Mos of this case is cased by MTU issue, So, I've tried to configure the following configuration on interface tunnel 0.Device: Cisco 7609 with IOS s72033-adventerprisek9_wan-mz.122-18.SXF8.bin
I've tried to figure out what the supporting command after 'ip tcp' in tunnel 0 and following likes..ip tcp ?compression-connections Maximum number of compressed connectionsheader-compression Enable TCP header compression.there is no such command about 'ip tcp adjust-mss.So, my questions is that what is the replace command for 'ip tcp adjust-mss' ? Is this only support on Router? such as Cisco 7200. or not, to take effect same functional on C7609, what is the command for that?
To understand and configuring VPN setup to give secure access to my DB & Application Server exist in my Datacenter, to other Service Provider organisation. They need to access those DB & Application Server sitting at their company LAN itself.
All the DB & Application Server connected to Distribution Switch in various VLAN,The Server support team from another company need the access to those, for that we will take MPLS link connecting out Core Router.
how can i check if my netgear N300 adapter wna3100 is compatible with apple tv device I was told that I needed a dual band router to play HD movies from itunes (ipad)
I've configured port forwarding on an ASA 5505 to connect to an Access Point web administration.This Is for testing purposes only. I've followed the guidelines for port forwarding and I've created an access list but I can't connect to the AP.I know It's working because It connects fine when connected to my speedtouch router.I've attached a running-config.I'm getting hit counts on the ACL and I'm getting untranslate_hits on the nat but no translate hits.
I have 10 AIR-LAP1131AG-A-K9 connected to a 4402 controller. I have a couple of questions:
- When I go into CONFIGURE/ACCESS POINT, one of the AP's has the message "**Configuration is different on the Device**". How do I connect directly to the device to check the settings? I tried to telnet but that didn't work.
- Are these access points capable of acting as a DHCP server? If so, where can I check this setting? I have workstations that are unable to pull an IP address from my DHCP server running on a Windows server. I want to make sure the AP's and/or the controller are not the issue. The clients see the SSID and the signal is strong, but when they connect they get limited network connectivity message and the IP addr is 169.254.97.123 (which is wrong).
Is it possible to create a job what automatically export the devices configs that are in the folder CSCOpxfiles medemushadow? It would be wonderdul if CW could export the .cfg files into a .rar and send in email or something like this.
I'm using cisco LMS 4.0, I've discovered the device and next plan is to collect the device configuration.I would like to know, How I can collect the configuration for single device.What configuration changes required on my LMS & Cisco device.
I have a problem exporting the config from a 1112 appliance. It does not boot up properly. GUI logon and authentication is not possible. I can console and SSH to it but the only thing i get is the commands below and nothing else.
login as: admin admin@10.10.1.126's password: Last login: Wed May 30 11:11:42 2012 from jsmith Could not chdir to home directory /home/admin: No such file or directory
acs> API called before initialised at V:ismg_israel_acsAcsEndPointCoreendpoint.cpp:395 Command Description ---------------------------------------------------- ? List commands exit Log off help List commands csutil -dumpadmin Dump Admin Audit Information csutil -dumpgroups Dump Group Audit Information csutil -dumpusers Dump User Audit Information csdbsync -syncnow RDBMS synchronization
i did a reset on my asa by stopping the boot process because i could not remember what my enable password was, i had no problems with the reset the asa came backup as it should and i started configuring the device again. My problem is when the device is powered off and back on i lose all configuration that were made, i save the changes with "write me" before the restart and they are still being over wrote.
we just replace 6500 with N7K, after migration there're some device (server,pc,printer) change its ip address configuration (subnet and gateway) by it self. can N7K did it?
When trying to view the status in the Monitor tab and the Config tab after you log in to the ACE 4710 Device Manager A5 (1.2) management GUI tool, I could not retrieve the status data and the following message appeared.
"Faild to upload Adimn configuration: There is error in loading configuration: Error in loading RMO config from DB:The given index XXXXXXXXX.bak does not match table index definition"
Other features include all normal, so I can get information by using the CLI.In addition, this configuration is redundant in the Primary / Secondary, this event occurs only on the Primary.
Other:-XXXXXXXXX.bak is a backup that you created in the checkpoint, and it does not already exist.
-When I'm logged on to the GUI, the above message is displayed in the status bar always.
-It was not recovered by ACE restart it.
-When I try to create the same configuration in a different environment, it did not reproduce.
This is IOS 15.1(4)M3 on a 1921 router. The LAN is 192.168.42.1/24. (DHCP config is further down.) We have a small range that we want to assign via DHCP to devices; .200 through .220 . At the same time, we have a handful of Macintosh systems to which we want to assign a specific address that is not in that 200-220 range. I don't want to configure the assignment based on the Ethernet MAC addresses because these systems might connect via UTP or wireless; that is to say, they have more than one MAC address. They only ever connect using one interface/MAC address at a time, but it's their choice; in some areas wi-fi is available, and in some areas they have to cable-up.
The Mac OSX network settings has a field for "DHCP Client ID". It would be much easier to tell the users of these systems to put their Mac's name in the Client ID field for both their wired and wireless DHCP configs. (As opposed to having them all lookup, and then give me their Ethernet MAC addresses for both of their interfaces.) I tried this with my Mac's (named "shrike") wi-fi interface, but I don't get the 192.168.42.14 address that I expected. I get an address from the .200 to .220 range.
Here's the DHCP-related config from the router:
router#sh run | s dhcp ip dhcp excluded-address 192.168.42.1 192.168.42.199 ip dhcp excluded-address 192.168.42.221 192.168.42.254 ip dhcp pool OurOffice network 192.168.42.0 255.255.255.0
[code]....
Is "client-name" the wrong place to configure the DHCP Client ID?
This is regarding CISCO logging configuration.We palnned to implement enable logging on all the cisco nexus switchs.we are running HP arc sight in our DC this device monitor all the CISCO devices.We want to enable logging with this Arc sight device.Just I would like to know about config commands for Nexus device, what is the command to enable logs which is include "who is login & logout?, interface down information?,who was did conf t ? & every logs"
I am currently setting up a new VRF on a Cisco 7609 which is advertising (as a RR-Client) an iBGP route to a Juniper MX960. This route is then getting sent back to the default route table on the 7609 but rejected due to the cluster-id loop prevention. Although not ideal I need this route to be visible in both tables.Is there a way of changing the bgp cluster-id per VRF rather than just globally?
What are the prerequisites before doing this? I have to upgrade a router this week if there is an opportunity to move it to a code that is more current that the one the client is currently running which is 12.2(33)SRD4. I see on the Cisco Support site that after this code, everything moves to 15.
We have a router 7609 with Supervisor Engine 720 (WS-SUP720-3B) (Policy Feature Card 3 and MSFC3 Daughterboard) and We have to configure QoS over a FastEthernet interface on a WS-X6148-RJ-45. When I try to apply the policy command I get the next log:
#service-policy output TEST_QOSbandwidth percent command is not supported in output direction for this interfaceConfiguration failed on: FastEthernet1/2 What kind of hardware and software requirements I need on my router to perfom QoS over ethernet interfaces?
Configuring MPLS over GRE tunnels. I did not find any proper configuration example. I need to do this for encrypt the traffic between two PE routers. I have 7609 routers.
I have a hight CPU utilisation problem in my CISCO7609-S routers. the cpu utilisation can rise 99% et this is usually. In the moment of hight CPU the the process CPU give the following:
First and foremost, what I have are 2 x 7204VXR (Gateways), 1 x 4507R-E (Coreswitch), and our ISP have 7609.Got some issues with redundancy with our ISP.
7609 I I I I 7204-A 7204-B | | | vrrp | | | -4507R-E- | | internal network
Both outside interfaces of 7204 gateways are connecting to 7609 with different public ip block. I used VRRP for my internal nework and failover have been tested working.
Even tried to remove link of 7204-A and 7609, the failover works perfect. If I shutdown/ remove the link between my 4507R-E and 7204-A (primary gw_higher vrrp priority), vrrp redundancy/failover still works, but pings from internal network to internet is only 50% success....alternate 4 ping reply and 4 time out.
I have to do a migration of sup32 to RSP720 for which I need to know if you can operate the equipment connected with the 2 supervisors at the same time??? and it still working ?
I have a router CISCO 7609-S with two RSP 720 engines,and other cards are 7600-ES+20G3C,7600-ES+40G3C.One day it has a error cord " %XDR-6-XDRIPCNOTIFY: Message not sent to slot 4/0 (4) because of IPC error queue flush. Disabling linecard. (Expected during linecard OIR)" and the card resets.Cisco TAC told us it is a bug which is CSCtj05576.and I want to upgrade the ios from c7600rsp72043-advipservices-mz.122-33.SRD4.bin to c7600 rsp 72043-advipservices-mz.122-33.SRE5.bin.Now I want to know this:1, Is it right to upgrade to this new ios? Is the new ios suitable for the cards?2,I want to know the right way to upgrade ios in two engines.
Atfer I copy the new ios to the master engine and slave engine,and then change the bootvar and save config.Is it auto copy the config to de slave engine?Atfer do this ,I want to know how to apply the new ios,Does it reload the slave engine first and then force-switchover the master engine to slave engine. Or Atfer do this,I reload the router on active engine directly?
In my existing production router 7609 of my company, sup-engine already fixed in slot 5 with SRC2 12.2(33) IOS and I need to insert another sup engine in slot 6 with SRE7 IOS code image and after this, again sup engine in slot 5 must be with SRE7 IOS image...(also I have extra sup engines with SRE 7 code image ready with me) Query:i am going to offload router before proceed for this activity?i will insert new sup engine in slot 6 with SRE 7 ios image and now i need to re-install spare sup engine with SRE 7 code readily available with me by removing existing sup engine from slot 5 (Active) so what will be the proceedure to insert new sup engine with SRE 7 code in slot 5 and slot 6 with minimum downtime of router?
existing setup sup engine in slot 5 with SRC2 12.3 (old hardware) slot 6 is EMPTY
final result should be like this: sup engine in slot 6 with SRE 7 (new hardware)
I have a cisco 7609 running IOS version c7600rsp72043-advipservicesk9-mz.122-33.SRE0a.bin with the following modules..
sh mod Mod Ports Card Type Model Serial No. --- ----- -------------------------------------- ------------------ ----------- 3 20 7600 ES+ 7600-ES+20G3CXL
[Code]....
The circuit has been tested as clean , so for the moment we have to assume that it is not a circuit issue We also have another idential 7600 in another POP with similar config that does not display the same problem
I have a 7609 with a Flexwan module with a PA-POS-1OC3. Is there a command to determine they type of SFP in the module ? sho controllers POS didn't provide the SFP type.
We have Cisco 7609 Router and one 6 Mbps link which is on ethernet . When we are trerminating on Gigaethernet of 7609 router it is not coming up. While same link is showing up and working fine on other routers which is having Ethernet interface.
