I have issue about Wireless controler , i have 2x WS-C3750G-24WS and 1x AIR-CT5508-50-K9 , i have max 50 access point license and i can't upgrading because WS-C3750G-24WS is and of life , can i use AIR-CT5508-50-K9 with 3750G to work together? , mobility and everything....
View 1 RepliesWhether we can configure HA between AIR-CT5508-100-K9 and AIR-CT5508-25-K9. Or we should require this AIR-CT5508-HA-K9 ?
View 6 Replies View RelatedI’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
I am in the process of upgrading our stack of 4 switches consist of WS-C3750G-48PS. Upon reading release notes found that there are two versions of release notes 1 day apart, the one 02 Sep 2012 saying that WS-C3750-48PS is not supported in this version. Then in release next day 03 Sep 2012 that note has been removed. Which one is correct. Is it supported with my model of switch or not. Also unable to update boot path in the stack switches, "switch all" is not supported in the current IOS. Any other way to update it. Master switch has new boot path but unable to change in slaves.
View 2 Replies View Relatedi have a Layer3 Switch Cisco WS-c3750G -24T , initially i have a IOS version c3750-Ipbase , recentely i have upgraded my IOS to c3750-Ipservices-M to enable to PBR for my network , i have created all the acl and tried to give the route-map with PBR , the command was initiallying but i am not able to see the applied route-map in my policy route , i have gone through the blog and enabled SDM prefer routing , but no luck .
View 1 Replies View RelatedI do have C3750G-12s switch which is not able to boot as of the expected. Every time when I break the stack and try to use console i got a weird output from my console output. we need the stack to be break and use those switch separtally .
[code]....
Is there any hardware difference between Cisco WS-C3750G-24T-E and WS-C3750G-24T-S or they are the same switch with different running IOS?I have an stack of some WS-C3750G-12S-S and want to introduce a new WS-C3750G-24T. My provider offers me only a WS-C3750G-24T-E and I do not know if i am going to be able to downgrade the IOS.
View 10 Replies View RelatedI am in the process of upgrading our stack of 4 switches consist of WS-C3750G-48PS. Upon reading release notes found that there are two versions of release notes 1 day apart, the one 02 Sep 2012 saying that WS-C3750-48PS is not supported in this version. Then in release next day 03 Sep 2012 that note has been removed. Which one is correct. Is it supported with my model of switch or not.also unable to update boot path in the stack switches, "switch all" is not supported in the current IOS. Master switch has new boot path but unable to change in slaves.
View 1 Replies View RelatedIs it possible to have a license loaded on an AIR-CT5508-HA-K9 in order to have it working as a stand alone controller?
View 4 Replies View Relatedwe do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version 6.0.188.0.AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with them.However AIR-LAP1242G-E-K9s do not, there is a problem with establishing CAPWAP tunnel with the controller.The AP is seen on the controller for a while, with 0 time up-time, cannot change any settings on the AP via controller, and after a while it disapears from the controller, apears again and this repeats.
The APs and controllers are connected to the LAN campus.Controllers via two 1G links configured as Etherchannel to WS-C6506-E VSS switch with s72033-ipservicesk9_wan-z.122-33.SXI1.bin on it.APs to WS-C3750G-48PS with c3750-ipbasek9-mz.122-50.SE2.bin on it. 3750 is connected to the C6505 via two 1G links configured as Etherchannel.Below I copied the log I captured on 1242 and the controller. Highlighted ones are the ones which I think might bring a clue.
I performed some troubleshooting steps.
- As we have some other controllers available over WAN, I tested the 1242 AP with 2100, 4400 and also with the same model AIR-CT5508-K9 with SW version 6.0.188.0 over WAN and this worked always okay.
- I wanted to be sure that I eliminate any kind of out of sequence packet issue, so I brought down all redundancy L2 links so that the L2 path from the AP to the controller was only through one leg links.
- I also brought the second controller down to eliminate potential issue with having two of them up.
- The AP gets its IP from DHCP configured on the C6506 switch, I am always able to ssh to AP, so the IP connectivity does not seem to be an issue.
- I have more 1242s, all behave in the same way. I also connected them to some other 3750 switches we have in the campus, always the same.
- As this seems to be maybe a kind of ssl issue, I tried to play with controller settings, like enabling Accept... options under Security/AP Policy,but this did not work.
- I also tried to reboot the controller, no improvement.
- The APs came from the factory, so in the beginning everything was factory default in them. They were always able to download the image from the controller in the very initial phase. I still do have some of them untouched, so I can perform any troubleshooting steps with the fresh one.I can reproduce this, can also send debugging logs if needed.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
This Discussion has been converted into document:- [URL]
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
AIR-LAP1242G-E-K9 10.0.13.28 log
*Mar 1 00:00:05.922: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.536: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot1 1Radio 0
*Mar 1 00:00:07.672: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 304 messages)
[code]....
I've two wlc model CT5508 version 7.0.116.0. They are working fine except for the RF grouping part. When I look at the RF Group members part in the configuration, I can see only one wlc (the one I'm connected to). If I connect to the second one, in the same part, I've just one controller (so the second one..). I tried to restart the algorithm but no change. Each controller is configured with Group Mode set to auto, and their respective role are auto-leader...I tried to change the RF group name on both wlcs, but it didn't fix the problem. When I look at the logs, there is one which appear quite often:
*emWeb: Nov 29 10:32:07.764: %LOG-6-Q_IND: dtl_arp.c:2581 ARP input q exceeds limit. Current val = 50 [...It occurred 38 times.!]
i received access point types AIR-LAP1252AG-E-K9, which i want to connect to my wlan controller AIR-CT5508-K9. Update from IOS etc. is working fine. Also all access points are recognized by the controller.We got the AIR-LAP1252AG-E-K9 with two antenna versions.
View 1 Replies View RelatedWhat is the operating and/or peak power consumption (in kW) of a 5508 WLC with redundant power supplies?
The below power details are from the 5508 datasheet which lists 115 W as the maximum draw (0.115 kW) however this seems a bit low, is this right?
Input power: 100 to 240 VAC; 50/60 Hz; 1.05 A at 110 VAC, 115 W Maximum; 0.523 A at 220 VAC, 115 W Maximum; Test Conditions: Redundant Power Supplies, 40C, Full Traffic. Heat Dissipation: 392 BTU/hour at 110/220 VAC Maximum Cisco 5500 Series Wireless Controllers Data Sheet: [URL]
Basically I need to upgrade the license for Base-AP count to add 100 more AP's however my vendor has provided hardcopy of license as below:
-LIC-CT5508-UPG
-AIR-CAS-3KC-K9
-AIR-WIPS-AP-5
-L-NCS-1.0-100-ADD
My understanding is rigister LIC-CT5508-UPG/PAK number on cisco site and get .lic file however what is the use of other PAK where do i register this files with? Moreover , we do have NCS , MSE in place which is centralised devices.
i have setup of following AIR-CT5508-K9 controller and around 20 AP spread all over the place, two SSID one guest and one for my employees.
the one for guest has web authentication, using Iphone every 2 to 3 minutes it time out and i have to reenter the credentails for web authentication.
I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. If i add some config in primary controller or do some changes or reboot all the AP's are moving to backup controller. this doesn’t have any problem, but many AP's which moved to backup controller are losing VLAN mapping. This happens every time. Primary --> backup, backup --> primary. Both controllers have same vern...same config etc..
AP model: AIR-LAP1252AG-A-K9
Controler model: AIR-CT5508-K9
I get the following error message at startup.
---
Error (2048) found in fsck check - attempt to repair.---
What is the implication of the error message 106007? Do I have no problem continuing to be left out of this error?
I want to confirm if the access point (AIR-AP1141N-E-K9) can work with the Wireless LAN Controller (AIR-CT5508-25-k9)
View 2 Replies View RelatedWhen a client connecting to a specific AP (example AP01), after every 1800 sec uptime it will reconnect and join other unit AP (example AP02)Both AP physically installed distance is around 6 meters from each other. I conduct the testing where i get myself sitting in middle between these two APs.
01. If i disable settsion timeout this feature, or setting the seconds become higher value, what's the performance and security impact? Is it recomend to change the default 1800 seconds session timeout?
02. Is there anyway i can tweak on WLC controller to prevent the client after session timeout then associate with another AP. This will lead major performance impact as the client woudl possibility connect to the weak signal AP and effect on the performance.
These are the details for reference:Client detail
- Dell DW1520 wireless-N WLAN card, with firmware version 5.100.235.12
- CCX version 4 supported
- Layer 2 security is WPA2 personal with PSK.
- wireless radio an
Controller detail:
model is AIR-CT5508-K9
software version is 7.2.110.0
I have a 5508 wireless controller running version 6.0.199.4 (the image installed when the device was shipped) and I am trying to install by tftp version 7.3.112.0
The issue is when using tftpd32 gets to 82% transfered then fails with the error "% Error: Code file transfer failed - Error while writing output file"
I am in the midst of trying to update the controller firmware of a cisco wireless lan contoller 4402, and having some issues getting the file to transfer to the controller. i am currently running verison 5.0.148 on the controller and attempting to upgrade to the latest version of 7.0.230 and for whatever reason it continues to not transfer. I have tried all 3 methods of cli, gui and using wcs software. all the no avail , I have tried tftp32 and 3cdaemon with the same results.
The error that i am getting from 3cdaemon is got socket timeout aborting code 10054, failing at 66MB transfered. I increased the timeouts both on the wlc and the tftp client to no avail
the error i get on the wlc is Code file transfer failed - Error while writing output file
I have a few AIR-AP1242-E-K9 AP that I have upgraded to LWAPP, after the upgrade the AP's don't join the controller. But some AIR-AP1232AG-E-K9 on the same site joins without any issues.The controller is: AIR-CT2504-K9, SW: 7.0.220.0. [code]
View 8 Replies View RelatedFirmware downloaded, FW_WRT120N_1.0.06.001_US after pressing APPLY nothing happens after few minutes it says. "There is an error in the Content-type field. Click the Back button to return to the previous page and re-enter the information."
View 2 Replies View RelatedRegion : India
Model : TD-W8951ND
Hardware Version : V4
Firmware Version : 4.0.0 Build 120607
ISP : Airtel[/COLOR]
I have wifi connectivity issues. After continues usage the wifi connection fails suddenly. And doesn't work till I restart it.
A refurbisched WS-C3750G-24WS-S50 that we have send to our client should support 50 LAP (the unit says WS-C3750G-24WS-S50 at the back of the unit). Also the "show version" of the 3750 says WS-C3750G-24WS-S50.
He upgraded the WLC software from 4.0 to 5.0 then to 6.0 and finally upgraded to 7.0 now claims the web-interface only shows 25 supported access-points. We never checked the cli from the WLC before the upgrade.
Also he uploaded a old config file from a other S25 intergated WLC controller .
1) What could be the reason for this issue ?
2) How does the upgrading from 25 to 50 LAP work ? Is it like the PIX/ASA with a license key ?
3) When you upgrade the WLC sofware you only use a piece of universel code like the IOS right ?,can it cause a integrated WLC to loose the support for the 50 LAP ?
4) Can you use a config file from a S25 with out issues ?
5) What part-ID do we need to purchase when we want to upgrade a S25 to a S50 ?
I want to change the management IP of our wireless controller, I have 5 LAP1142N connected to this controller.
I have a few questions before I will do this task.
1. If I change the management IP, will the controller need a reboot?
2. Will the AP's automatically sync with the new management IP?
3. Do I need additional configuration on the AP's?
4. What else do I need to consider.
Q: a client has a network with 60 AP's controlled by a AIR-CT5508-50-K9 (+ L-LIC-CT5508-25A) with a redundant power supply. Can he get full redundancy by purchasing a second controller? If he purchases one, can he bring it into the network? What about the extra license for 25 extra AP's installed on the first controller?
View 4 Replies View RelatedI have this Wireless deployment :
Main Site: WLC AIR-CT5508-50-K9
WCS 6.x for 50 APs
(32 ) AP 1140
02 Remote Sites : 03 AP 1140 using H-REAP
Now, my company is considering to implement a wIPS solution, so i planned to install in the Main Site a MSE3300 and (01) AP 3500e as a wIPS AP Monitor in the remote sites,
Need to confirm:
A) Can an AP3500 work with HREAP and as wIPS monitor AP at the same time? or in other words, if it is possible to have an AP wIPS monitor far away from the WLC (over the WAN)?
B) What are the requirements of WAN link if I want to install a Centralized MSE 330 Engine,which perform the wIPS solution in all the network.
Some of my Lightweight Access Points lose connection every 10 minutes now, it worked without problems before.
I'm using an AIR-CT5508-K9 Controller with Version 7.0.116.0 and AP are all AIR-LAP1242AG-E-K9.
In the log I find informations about my node changing his parent and then reseting the radio interface.
I checked my configuration, but perhaps I missed something.
7Mon Oct 31 14:35:11 2011AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:3a:99:90:55:c0 Cause=Radio interface reset. Status:NA8Mon Oct 31 14:35:11 2011AP's Interface:0(802.11b) Operation State Down: Base Radio
[Code]......
I'm currently running ACS 5.3 Patch 7 in a VM on VMware ESXi. I download the application upgrade bundle, and placed it in my SFTP repository, and ran "application upgrade filename repository name". It throws an error that the manifest file is not found in the bundle.
I tried putting the ACS.gz file in an FTP repository, and even in an ISO file to attach to the VM. In all cases I receive this same error.I did verify the md5sum on the file to make sure it wasn't corrupted..
Not abe to upgrade the IOS image PIx7.0 from earlier version 6.3 in to my old Pix-525 FO(Secondary unit) license box .
Is it possible to upgrade without Primary unit (Unrestricted License) ?
I would like to upgrade rommon on my Cisco 2801 but this is what I get: [code]The router stops here and I am forced to power off and on again and the upgrade does not succeed.
View 10 Replies View RelatedHave the DIR-655 Hardware Version A1. Firmware 1.00NA dated Feb 2010. When I try to upload ANY firmware update from the DLINK site, it says that it is not for that device or is corrupt.
View 5 Replies View Related