Cisco Wireless :: WS-C3750G-24WS-S50 Only Supports 25x AIR-LAP1242 Instead Of 50
Sep 1, 2012
A refurbisched WS-C3750G-24WS-S50 that we have send to our client should support 50 LAP (the unit says WS-C3750G-24WS-S50 at the back of the unit). Also the "show version" of the 3750 says WS-C3750G-24WS-S50.
He upgraded the WLC software from 4.0 to 5.0 then to 6.0 and finally upgraded to 7.0 now claims the web-interface only shows 25 supported access-points. We never checked the cli from the WLC before the upgrade.
Also he uploaded a old config file from a other S25 intergated WLC controller .
1) What could be the reason for this issue ?
2) How does the upgrading from 25 to 50 LAP work ? Is it like the PIX/ASA with a license key ?
3) When you upgrade the WLC sofware you only use a piece of universel code like the IOS right ?,can it cause a integrated WLC to loose the support for the 50 LAP ?
4) Can you use a config file from a S25 with out issues ?
5) What part-ID do we need to purchase when we want to upgrade a S25 to a S50 ?
What is the maximum group of HSRP Group that supports the WS-C3750G-24T-S running the IOS c3750-advipservicesk9-mz.122-44.SE2.bin?I have this message:Mensaje ERROR: %Platform already has maximum FHRP groups configured
Is there any hardware difference between Cisco WS-C3750G-24T-E and WS-C3750G-24T-S or they are the same switch with different running IOS?I have an stack of some WS-C3750G-12S-S and want to introduce a new WS-C3750G-24T. My provider offers me only a WS-C3750G-24T-E and I do not know if i am going to be able to downgrade the IOS.
Did you meet this issues that the remote site (US) AP 1242 always connect to our site(ASIA) WLC 5508 (maybe some DHCP configure caused when troubleshooting, right nowDHCP back to normal. only enable vendor and option 43 for 1262 and 3602, no option 43 for 1242), but now we cannot block these AP1242 to join our site 5508 WLC. even I reset the 1242 AP to default configure from WLC GUI and CLI , but it's still there in a mins.
Since in our site Core SW, Router cannot find these AP mac address, and also those AP not the IP address in the WLC GUI and CLI .
I have some LAP1242 which by mistake were bought for Mesh. I am trying to convert them to LWAPP so what I did first was to convert them to Stand Alone then to LWAPP but I cannot get the AP to join the WLC and sends several error logs.
I attached some logs taken from AP and WLC so that you can figure out what's going on.
I wonder if I have to remove anything from flash either on SA or LWAPP mode (I know that in some cases you have to delete privete-config in order to avoid the AP taken previous configurations). By the way I think I had never seen this c1240-k9w8-mx.124-25e.JA2 on an AP IOS before, I wonder if it has to do with the mesh thing.
I have a Cisco 4402 WLC running version 4.2.112.0 controlling 20+ AIR-LAP1242AG-E-K9 access points running IOS 12.4 (10b). I'm trying to setup an additional AP as MESH. When I try to change the mode from local to bridge, on what will be the rootAP, I get a message stating that bridging is not support on this unit.
We currently have some LAP1242AG AP's meshed together inside our building.The owner (without consulting IT) was able to aquire some LAP1510AG's that he want's to deploy for outdoor use.Can they be meshed into our current network without having to cable one of the 1510's to the network?
I have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in.
I have 2 Air-Lap1242 that wont save their config after reboot. They are managed by a WLC (4404) and it all seems pretty fine and dandy, but when i reboot them, they dont want to save anything.
I am setting them up as bridges (mesh), and it works until i reboot them, then I have to do it all over again.Using CLI to type in "write mem" or "copy running-config startup-config" only results in: "Building configuration... [OK] -> NVRAM Verification Failed".
I have issue about Wireless controler , i have 2x WS-C3750G-24WS and 1x AIR-CT5508-50-K9 , i have max 50 access point license and i can't upgrading because WS-C3750G-24WS is and of life , can i use AIR-CT5508-50-K9 with 3750G to work together? , mobility and everything....
Is there a wireless router available that will support a free dynamic DNS provider such as [URL], without the need for custom firmware?
I have a device that requires DDNS, and I do not want to mess with firmware updates. I've already bricked a router trying to do that. So I'm looking for a replacement router that requires little to no modifications to use a free DDNS provider.
Customer is interested in deploying the 3600 AP's but will not be able to replace all his 1231's, any chance there is a release between 7.0.220.0 and 7.1.91.0 that will support both AP's?
Region : India Model : TD-W8951ND Hardware Version : V4 Firmware Version : ISP :
The product manual of TD-W8951ND V4 states that it's supports MAC spoofing. But in the product itself, it is nowhere to be found. I tried contacting the customer care via email but they are too lazy to respond. If they disabled this feature then why in the world they mentioned in the manual. I double checked the manual before buying this model. Now I stuck with it.
Region : UnitedKingdom Model : TL-WR841N Hardware Version : V8 Firmware Version : ISP :
I'm interested in purchasing this router but I need to know how many clients it supports. We currently have a normal adsl wireless router but after about 20 clients it stops accepting anyone new.
Region : UnitedKingdom Model : TL-WR841N Hardware Version : V8 Firmware Version : ISP :
I'm interested in purchasing this router but I need to know how many clients it supports. We currently have a normal adsl wireless router but after about 20 clients it stops accepting anyone new.
I'm looking for a device which will allow me to forward all internet bound traffic through a L2L IPSec tunnel from branches to a central hub and internet connection.
I've recently purchased a RV120W(as a test branch device) which i've tried to get working with the ASA5505 at the central site. I can get the VPN to come up but can't manage to get the internet bound traffic through it. Reading up on the issue, it looks like full tunneling or IPsec wildcard forwarding isn't supported on the RV120W and RV220W devices [URL] The source mentions that the RV0xx series supports this feature, however one of my requirements is wireless on the device.
Any device which supports this rather than just the standard split tunneling, alternatively a workaround which will allow me to use RV120Ws at branch sites? Would an SRP521 support what i'm trying to achieve?
I have a WRT54G router V6, and I am wondering how many wireless connections it supports? Because, I have one wired connection and whenever I try to connect more than 4 wireless devices a device will get booted.
I would like to ask for a cisco wireless router that supports captive portal. I notice that WAP321 supports this but what other additional units should be added in order to accomplish this. Client wants the user to authenticate first and also to see who logs in.
I have a couple of Cisco WS-C3750G-12S-E, I`m putting to use again. These will be doing routing (IPv4 and IPv6), VLANs, VRF etc etc.
In Cisco Feature Navigator I find that the newest IOS for this model is 15.0(1)SE and 12.2(58)SE. But my supplier says c3750-ipserviceslmk9-tar.122-55.SE3.tar is the latest. What is the most feature rich, best, stable image I can load on this unit.
Our network system has 125 different Vlans (Cisco) and I would like to be able to route between only 2 particular Vlans, I know with the command “ip route “ in our layer 3 switches (ws-c3750G -12S) I would be able to route among all Vlans but I need to be able to route between 2 Vlans to be able to access the PCs in vlan 1 from vlan 2 and wise versa.The IP range of vlan1 is 10.0.8.XXX /24 and Vlan2 10.0.11.XXX /24.
I have 2 CISCO WS-C3750G-12S-E witch I`m concidering using as redundant VLAN routers for a small WISP network.Do not have much experiences with these, so I might be asking stupid questions...The network has about 2000 connected clients.
Traffic is about 300 - 400 Mbps duplex.
100000 - 150000 PPS
Expected this to get to about 3000 connected clients.
Traffic about 500 - 700 Mbps duplex.
150000 - 200000 PPS
Before these end their duty Are they up for the task, or do you reccomed something different?
Using the VRF- Lite functionality on Cisco 3750G's (WS-C3750G-24T-S), I've got a situation currently with a set of 3750's running inter- v LAN routing for around 80/90 connected sub nets (140+ gig ports). I'm looking in the coming week at creating a new VRF and enabling OSPF for that VRF while leaving the existing routing arrangements in the Default IP Routing Table.
I'm in a situation where I can't replicate the live config into a lab to test the impact / implications of enabling / creating VRF's. I know the 3750's have a very small support for VRF's (24 if I recall) but I only plan on using 2 or 3 max currently.
I have this WS-C3750G-24T 16Mb flash switch and running on IOS Version 12.2(25)SEE4, RELEASEI would want to know a IOS version that supports IP SLA feature and which is compatable to the above model Switch.
I have already set up a lab comprising of 1x2950-24 switch, 2x3750-24T in stack mode and 2x MS Domain Controller with AD 2008 Servers and NPS enabled (Domain level 2008). I use NPS as a Radius Server. I am trying to test the 802.1x framework in two scenarios.
1. I use as client a domain laptop with Windows XP SP3 with the embedded 802.1x MS supplicant. As authenticator use the 2950 switch and as authentication servers I use the two NPS integrated in MS DCs. Everything is working fine as I expected with basic configuration guidelines from Cisco & Microsoft.
2. I use as client a domain laptop with Windows XP SP3 with the embedded 802.1x MS supplicant (the same as before). As authenticator I use the 3750 Stack switch and as authentication servers I use the two NPS integrated in MS DCs (the same as before). I have configured the supplicant for both machine or user authentication in both scenarios. However the client never pass the authentication in the second one. I disconnect and connect the same supplicant in the 2950 switch and the authentication is completed successfully. Getting back to the 3750 stack the authentication failed and the laptop gains network access in the configured Auth-Failed Vlan. I have tried several configuration changes without success. I cannot understand why does this happen. I have made some debugs and I am sending them a long with a partial basic configuration of 3750 stack switch.
Any replacement fan for the WS-C3750G-48TS-S switch that runs quieter than the one originally built into this router? I've searched a number of web sites and found plenty of replacement fans available but none of them show noise level specifications.
particular manufacturer/model combination that works in this router that will drop the noise level down while maintaining air flow. This switch is in a short network rack in an small office that also includes people. The current noise level isn't defining like some servers, but is loud enough to be distracting.
I`m trying to get a simple VRF and routing setup going.The "routers" are Cisco C3750G-12S-E.What I want to do is separate the management network form all else.The public network is illustrated with private IP ranges, these are really public ranges.
I think the best way to solve this will be using VRF for management, and regular routing for public network, right? Putting the management network in it`s own VRF.
I am in the process of upgrading our stack of 4 switches consist of WS-C3750G-48PS. Upon reading release notes found that there are two versions of release notes 1 day apart, the one 02 Sep 2012 saying that WS-C3750-48PS is not supported in this version. Then in release next day 03 Sep 2012 that note has been removed. Which one is correct. Is it supported with my model of switch or not. Also unable to update boot path in the stack switches, "switch all" is not supported in the current IOS. Any other way to update it. Master switch has new boot path but unable to change in slaves.
We recently connected a RPS 2300 to our switch WS-C3750G-48PS-E with IOS c3750-ipservicesk9-mz.122-53.SE2.bin.However i do not see any RPS details in the"show env" output.I believe i should get the RPS Name and its Serial and the port number in the output, but i am not finding it in the output. I did reload the switch but still couldnot get this udpated.
