I`m trying to get a simple VRF and routing setup going.The "routers" are Cisco C3750G-12S-E.What I want to do is separate the management network form all else.The public network is illustrated with private IP ranges, these are really public ranges.
I think the best way to solve this will be using VRF for management, and regular routing for public network, right? Putting the management network in it`s own VRF.
I am attempting to upgrade from a Cisco3945 to a ASR1002. On my Cisco3945, I have interface associated with VLANs. It appears that with the new IOSX, VLAN configuration has changed. Any config to setup a simple VLAN?
View 5 Replies View RelatedI would like to create 3 x VLANs on an SG 300-28P and have them completely isolated from each other, for example ports 1 - 12 on VLAN 1, ports 13 - 24 on VLAN 2 and ports 25 - 28 on VLAN 3. No communication between any of the VLANs.
Any simplest way to achieve this?
I would like to setup a simple VPN on a small network, nothing special, just to provide access to some simple resources on the network from anywhere. Since I'm not a Cisco expert, I was advised to user a 861 router, but I just can't seem to get the VPN working on this device.
I've placed the router behind a modem and did some basic configuration. Hosts who are connected to the modem (on the Vlan side) can access the internet and can setup a VPN connection to the router. A VPN connection from inside the network is worthless, but I just can't get the VPN working on the FastEthernet4 connection.
Any VPN config for a 861 router for this situation? Or how to configure this device as a VPN server?
Is there any hardware difference between Cisco WS-C3750G-24T-E and WS-C3750G-24T-S or they are the same switch with different running IOS?I have an stack of some WS-C3750G-12S-S and want to introduce a new WS-C3750G-24T. My provider offers me only a WS-C3750G-24T-E and I do not know if i am going to be able to downgrade the IOS.
View 10 Replies View RelatedOur network system has 125 different Vlans (Cisco) and I would like to be able to route between only 2 particular Vlans, I know with the command “ip route “ in our layer 3 switches (ws-c3750G -12S) I would be able to route among all Vlans but I need to be able to route between 2 Vlans to be able to access the PCs in vlan 1 from vlan 2 and wise versa.The IP range of vlan1 is 10.0.8.XXX /24 and Vlan2 10.0.11.XXX /24.
View 11 Replies View RelatedI have 2 CISCO WS-C3750G-12S-E witch I`m concidering using as redundant VLAN routers for a small WISP network.Do not have much experiences with these, so I might be asking stupid questions...The network has about 2000 connected clients.
Traffic is about 300 - 400 Mbps duplex.
100000 - 150000 PPS
Expected this to get to about 3000 connected clients.
Traffic about 500 - 700 Mbps duplex.
150000 - 200000 PPS
Before these end their duty Are they up for the task, or do you reccomed something different?
I'm just getting started with cisco kit so you will have to bare with me.I have a cisco 1841.i have a very wierd issue of routing...i cannot ping and browse through this.
View 3 Replies View RelatedI am in the process of upgrading our stack of 4 switches consist of WS-C3750G-48PS. Upon reading release notes found that there are two versions of release notes 1 day apart, the one 02 Sep 2012 saying that WS-C3750-48PS is not supported in this version. Then in release next day 03 Sep 2012 that note has been removed. Which one is correct. Is it supported with my model of switch or not. Also unable to update boot path in the stack switches, "switch all" is not supported in the current IOS. Any other way to update it. Master switch has new boot path but unable to change in slaves.
View 2 Replies View RelatedWe recently connected a RPS 2300 to our switch WS-C3750G-48PS-E with IOS c3750-ipservicesk9-mz.122-53.SE2.bin.However i do not see any RPS details in the"show env" output.I believe i should get the RPS Name and its Serial and the port number in the output, but i am not finding it in the output. I did reload the switch but still couldnot get this udpated.
View 3 Replies View RelatedCurrently there are three stacked WS-C3750G-24TS-1U on data centre. I am going to buy a WS-C3560X-48T-L to use 10GbE module. Is it possible stack this switch "WS-C3560X-48T-L" to current switches "WS-C3750G-24TS-1U" ?
View 1 Replies View RelatedI have a process whick take all the CPU on two differents Stack of WS-C3750G in version 12.2.53(SE2):
XFRPALSN02R#sh proc cpu sorted CPU utilization for five seconds: 97%/3%; one minute: 95%; five minutes: 95% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 307 5450059 4167397 1307 86.74% 83.63% 83.35% 0 hulc nrgyz PD di XFRPALSN02R#sh proc cpu sorted CPU utilization for five seconds: 96%/3%; one minute: 96%; five minutes: 96% PID Runtime(ms) Invoked uSecs 5Sec 1Min 5Min TTY Process 307 7779608 5947379 1308 86.26% 85.75% 85.30% 0 hulc nrgyz PD di
I have the following switch:
#show version
Cisco IOS Software, C3750 Software (C3750-IPSERVICES-M), Version 12.2(52)SE, RELEASE SOFTWARE (fc3)
Copyright (c) 1986-2009 by Cisco Systems, Inc.
Image text-base: 0x01000000, data-base: 0x02C00000
ROM: Bootstrap program is C3750 boot loader
BOOTLDR: C3750 Boot Loader (C3750-HBOOT-M) Version 12.2(44)SE5, RELEASE SOFTWARE (fc1)
[code]...
I have downloaded c3750-ipservicesk9-mz.150-1.SE2.bin and I want to upgrade iOS to this image.
I have a few questions related to this:
1. Is my switch model compatible with this iOS version?
2. Do you recommend the upgrade? Does it bring some notable features?
3. Can I upgrade for free or do I need to buy some license?
4. I also want to upgrade/add the crypto image, can I add crypto for free or some license is required?
5. I have remote access to my switch via the console cable which plugged into machine1. But machine1 is connected to network via the same switch. I am accessing machine1 via SSH, and then the switch via console cable (minicom on CentOS). Is there an upgrade procedure for this kind of situation that also has some fall back (like reboot in X minutes and load the previous image) if the upgrade goes wrong?
We are facing since one month in our two Cisco WS-C3750G-12S on many interfaces input errors when data transer or ping (ICMP) increase input erros. Not only port 1 but many interface has same issue, i have change new IOS but still same issue, once i have erase startup config but same issue we are facing and finaly i have replace same new switch with the same IOS it's working fine.(c3750-ipservicesk9-mz.122-55.SE4.bin) [code]
View 11 Replies View RelatedI currently have a C3750G connected to a C3560G with default auto-negotiation settings. Ports are up and connected a-100 and a-full. I am trying to change the ports speed to 1G, and have tried all possible combinations of "speed 1000" and "duplex full" setting on both ends to no avail. What should port settings be for 1G speed between the two switches?
Here are the current port settings:C3750G:
interface GigabitEthernet1/0/1
switchport trunk encapsulation dot1q
[Code].....
i have a Layer3 Switch Cisco WS-c3750G -24T , initially i have a IOS version c3750-Ipbase , recentely i have upgraded my IOS to c3750-Ipservices-M to enable to PBR for my network , i have created all the acl and tried to give the route-map with PBR , the command was initiallying but i am not able to see the applied route-map in my policy route , i have gone through the blog and enabled SDM prefer routing , but no luck .
View 1 Replies View RelatedI have Catalyst C3750G switch
with configured route to subnet 192.168.201.0/24
ip routing
ip route 192.168.201.0 255.255.255.0 192.168.160.13
192.168.160.13 is accessible
[Code].....
can i stack cisco (ws-c3750G-12s) with (ws-c3750X-24p-poe-s) with (ws-c3750-48p-10/100 poe) i mean even a switch is 10/100 and the other switch is 10/100/1000?
View 3 Replies View RelatedI'm having trouble stacking a new WS-C3750X-24P with existing switches WS-C3750G-24PS ?I can see the license is on the new WS-C3750X-24P:
switch#sho lic
Index 1 Feature: ipservices
Period left: 8 weeks 4 days
License Type: Evaluation
License State: Active, Not in Use, EULA not accepted
License Priority: None
[code].....
I could put on the c3750e-ipbasek9-mz.122-55.SE1 image, but I may need to get the license sorted still, but not sure if that will work or how to add it if i got one.....
I have two Switches which i need to put in a same stack - WS-C3750E-48TD and WS-C3750G-48TS . Possible to do so and also which IOS to put in both the switches as WS-C3750G-48TS is having lower RAM and flash.Whether can i put following IOS in these switches and connect them in a stack as i have read that IOS -- 15.0.1. SE are compatible with both the switches.
a . c3750e-ipbasek9-mz.150-1.SE.bin in switch - WS-C3750E-48TD
b. c3750-ipbasek9-mz.150-1.SE.bin in switch -- WS-C3750G-48TS
I do have C3750G-12s switch which is not able to boot as of the expected. Every time when I break the stack and try to use console i got a weird output from my console output. we need the stack to be break and use those switch separtally .
[code]....
I have 8 switch stack consisting of six WS-C3550-48P and two WS-C3750G-16TD running software vesrion 12.2(25) SEB1. When I added new C3750v2-24PS (running image 12.2(50) SE5) in stack so I up-graded the image of existing 8 switches with latest veriosn 12.2(50) SE5. Once I have done with the upgrade then all ports of my stack switches went down after around five minuts. Is it image compatibility issue with existing switches or something else?
View 7 Replies View RelatedSituation: Currently WS-C3750G-48TS-(S or E) switches are on stack. Now these units will soon EOL on Jan. 30, 2013 and Cisco recommends that
WS-C3750X-48T-S or WS-C3750X-48T-E will be used.
The question is: Will the new SKU works together in a stack with the old ones? Will there be no changes on the type of stacking cable to be used?
Inter-VLAN applications are slow and same VLAN it is working fine.(i.e.VLAN to VLAN applications and File transfer response was Slow).Switch Model number: WS-C3750G-24TS-S1U
View 3 Replies View RelatedI have a situation. I am running two-switch 3750-stack and it crashed this morning. IOS version the switches is: "flash:c3750-ipservicesk9-mz.150-1.SE.bin"
SRPRSRGBYA#
Log Buffer (10000 bytes):
3:40.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan104, changed state to up
Nov 3 13:13:40.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan201, changed state to up
Nov 3 13:13:40.840: %LINEPROTO-5-UPDOWN: Line protocol on Interface Vlan202, changed state to up
M-1-CRASHED: (SRPRSRGBYA-1)
Nov 3 13:18:13.336: %PLATFORM-1-CRASH(code)
We have a cisco stack with 5 ws-c3750-24p 12.2)55)SE3 c3750-ipbasek9-m switches. Can i add a switch to the stack that is the following model: ws-c3750g-48ts 12.2(25)see3 c3750-ipbase-m
View 3 Replies View RelatedWhat is the maximum group of HSRP Group that supports the WS-C3750G-24T-S running the IOS c3750-advipservicesk9-mz.122-44.SE2.bin?I have this message:Mensaje ERROR: %Platform already has maximum FHRP groups configured
View 6 Replies View RelatedI need to replace an ADSL modem and have a spare 857W. Can I use this to act as a simple bridge between the ADSL PPPoA connection and the FW WAN port?
[ CISCO 857W ]
ISP - PPPoA - BRIDGE - FW WAN
I have a block of Public IP's so the PPPoA Dialer 0 connection would get x.x.x.185/29 I would like to bridge this directly to the FW WAN port and set that to x.x.x.185/29 with a gateway of x.x.x.186/32.Currently I am using it in router mode with no NAT or FW and am losing a Public IP as I need to set the FW WAN as x.x.x.186 with a GW of x.x.x.185 I am setting BVI 1 as x.x.x.185/29 and Dialer0 as IP Unnumbered BVI 1.
Got 2 of these switch stacked and there is some changes that we are going to undertake which will require us to utilize the whole 8 or 4 (2 from each switch) SFP ports. Just need some adivce on which particular fiber modules should I procure. Does this switch support 10GB of SFP ?
View 7 Replies View RelatedI have a WS-C3750G-24T-S layer 3 switch and I need to configure independent routes for a specific network, I'm trying to use VRF but it is not working for me. I tried using route-map but it seems the switch doesn't support that, so I'm stuck with VRF, but I think I'm not doing it right. The topology is as follows:
I have a network directly connected to a vlan and I need to forward all the traffic I get on this VLAN using a tunnel to a router. I think the problem is that in order to use the tunnel I need to utilize another VLAN which isn't part of that VRF. I attach the configuration I'm using to better understand what I'm trying to do:
layer-3 switch:
ip vrf TEST
rd 1:1
interface Tunnel1
ip vrf forwarding TEST
ip address 172.17.0.1 255.255.255.252
tunnel source 10.245.0.9
tunnel destination 10.250.4.31
[Code]....
And this is how my routing table looks on this router:
172.17.0.0/30 is subnetted, 1 subnets
C 172.17.0.0 is directly connected, Tunnel4
C 10.250.4.0/24 is directly connected, Vlan404
S 10.245.0.8/29 [1/0] via 10.250.4.1
S* 0.0.0.0/0 [1/0] via 10.1.60.15
we want to record voip telephone?Presently im using wireshark on a laptop to test the rspan session
Here is how it's configured
CORE_SWITCH is
Switch Ports Model SW Version SW Image
------ ----- ----- ---------- ----------
* 1 28 WS-C3750G-24TS 12.2(52)SE C3750-IPBASEK9-M
2 52 WS-C3750G-48TS 12.2(52)SE C3750-IPBASEK9-M
[code]....
Ive created the vlan 33 on my core switch and remote SPAN VLANs 133 Core switch is vtp server so i double checked on all switch and vlan 33 and 133 are present When i listen to conversation with wireshark we are only recoding voice of the one who is answering and we don't hear the other person talking?
I'm trying to stack 3750G & 3750X. As discussed in previous threads I am aware of that the version need to match.
Here the switch details:
Switch Ports Model SW Version SW Image
------ ----- -------------- ----------
* 1 24 WS-C3750G-24T 12.2(55)SE7 C3750-IPBASEK9-M
---------------------------------------------------------------------------------------------------------------
* 1 54 WS-C3750X-48 12.2(55)SE7 C3750E-IPBASEK9-M
I have changed the universal IOS on the 3750X to IP base..but they still wont come up as a stack. On the 3750X I don't see any log entry, on 3750G (major version mismatch).
A few days ago this was working properly, but I must have changed some things that adjusted some settings because I am unable to ping between 2 devices that are on the same switch, in the same network, in the same VLAN. I am able to ping to the VLAN interface on the switch.
This is my configuration (Catalyst 3560 Layer 3 switch):
ALGSWI01#show vlan
VLAN Name Status Ports
---- -------------------------------- --------- -------------------------------
1 default active Gi0/3, Gi0/4, Gi0/7, Gi0/9
[Code].....