Cisco Wireless :: Configure HA Between AIR-CT5508-100-K9 And AIR-CT5508-25-K9?
Jan 28, 2013Whether we can configure HA between AIR-CT5508-100-K9 and AIR-CT5508-25-K9. Or we should require this AIR-CT5508-HA-K9 ?
View 6 Replies
ADVERTISEMENT
Cisco Wireless :: Possible To Have License Loaded On An AIR-CT5508-HA-K9
Apr 25, 2013Is it possible to have a license loaded on an AIR-CT5508-HA-K9 in order to have it working as a stand alone controller?
View 4 Replies View RelatedCisco Wireless :: AIR-LAP1242G-E-K9 Does Not Work With AIR-CT5508-K9
Mar 11, 2012we do have a site where we need to deploy AIR-LAP1142N-E-K9 and AIR-LAP1242G-E-K9 APs. We have two AIR-CT5508-K9 controllers with SW version 6.0.188.0.AIR-LAP1142N-E-K9s work okay, as expected, we do not have any problems with them.However AIR-LAP1242G-E-K9s do not, there is a problem with establishing CAPWAP tunnel with the controller.The AP is seen on the controller for a while, with 0 time up-time, cannot change any settings on the AP via controller, and after a while it disapears from the controller, apears again and this repeats.
The APs and controllers are connected to the LAN campus.Controllers via two 1G links configured as Etherchannel to WS-C6506-E VSS switch with s72033-ipservicesk9_wan-z.122-33.SXI1.bin on it.APs to WS-C3750G-48PS with c3750-ipbasek9-mz.122-50.SE2.bin on it. 3750 is connected to the C6505 via two 1G links configured as Etherchannel.Below I copied the log I captured on 1242 and the controller. Highlighted ones are the ones which I think might bring a clue.
I performed some troubleshooting steps.
- As we have some other controllers available over WAN, I tested the 1242 AP with 2100, 4400 and also with the same model AIR-CT5508-K9 with SW version 6.0.188.0 over WAN and this worked always okay.
- I wanted to be sure that I eliminate any kind of out of sequence packet issue, so I brought down all redundancy L2 links so that the L2 path from the AP to the controller was only through one leg links.
- I also brought the second controller down to eliminate potential issue with having two of them up.
- The AP gets its IP from DHCP configured on the C6506 switch, I am always able to ssh to AP, so the IP connectivity does not seem to be an issue.
- I have more 1242s, all behave in the same way. I also connected them to some other 3750 switches we have in the campus, always the same.
- As this seems to be maybe a kind of ssl issue, I tried to play with controller settings, like enabling Accept... options under Security/AP Policy,but this did not work.
- I also tried to reboot the controller, no improvement.
- The APs came from the factory, so in the beginning everything was factory default in them. They were always able to download the image from the controller in the very initial phase. I still do have some of them untouched, so I can perform any troubleshooting steps with the fresh one.I can reproduce this, can also send debugging logs if needed.
+++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
This Discussion has been converted into document:- [URL]
++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++++
AIR-LAP1242G-E-K9 10.0.13.28 log
*Mar 1 00:00:05.922: %SOAP_FIPS-2-SELF_TEST_IOS_SUCCESS: IOS crypto FIPS self test passed
*Mar 1 00:00:07.536: %SOAP_FIPS-2-SELF_TEST_RAD_SUCCESS: RADIO crypto FIPS self test passed on interface Dot1 1Radio 0
*Mar 1 00:00:07.672: %LWAPP-3-CLIENTEVENTLOG: Read and initialized AP event log (contains, 304 messages)
[code]....
Cisco Wireless :: CT5508 / RF Group Members Not Seeing Each-other
Nov 28, 2011I've two wlc model CT5508 version 7.0.116.0. They are working fine except for the RF grouping part. When I look at the RF Group members part in the configuration, I can see only one wlc (the one I'm connected to). If I connect to the second one, in the same part, I've just one controller (so the second one..). I tried to restart the algorithm but no change. Each controller is configured with Group Mode set to auto, and their respective role are auto-leader...I tried to change the RF group name on both wlcs, but it didn't fix the problem. When I look at the logs, there is one which appear quite often:
*emWeb: Nov 29 10:32:07.764: %LOG-6-Q_IND: dtl_arp.c:2581 ARP input q exceeds limit. Current val = 50 [...It occurred 38 times.!]
Cisco Wireless :: WS-C3750G With AIR-CT5508-50-K9 / Unable To Upgrade
Oct 3, 2012I have issue about Wireless controler , i have 2x WS-C3750G-24WS and 1x AIR-CT5508-50-K9 , i have max 50 access point license and i can't upgrading because WS-C3750G-24WS is and of life , can i use AIR-CT5508-50-K9 with 3750G to work together? , mobility and everything....
View 1 Replies View RelatedCisco Wireless :: Want To Connect To Vlan Controller AIR-CT5508-K9
May 6, 2013i received access point types AIR-LAP1252AG-E-K9, which i want to connect to my wlan controller AIR-CT5508-K9. Update from IOS etc. is working fine. Also all access points are recognized by the controller.We got the AIR-LAP1252AG-E-K9 with two antenna versions.
View 1 Replies View RelatedCisco Wireless :: AIR-CT5508-K9 - Unable To Join AP To Controller
Nov 7, 2012I’m having a problem of joining new Aps( Ari-ap1242G-E-k9 ) to the following wireless LAN controller. WLC details as follows,
Model No - AIR-CT5508-K9
Software Version - 7.0.116.0
AP Model - ARI-AP1242G-E-K9
AP console logs attached in Error.jpg file
Cisco Wireless :: Power Draw / Usage For AIR-CT5508-K9?
Apr 17, 2012What is the operating and/or peak power consumption (in kW) of a 5508 WLC with redundant power supplies?
The below power details are from the 5508 datasheet which lists 115 W as the maximum draw (0.115 kW) however this seems a bit low, is this right?
Input power: 100 to 240 VAC; 50/60 Hz; 1.05 A at 110 VAC, 115 W Maximum; 0.523 A at 220 VAC, 115 W Maximum; Test Conditions: Redundant Power Supplies, 40C, Full Traffic. Heat Dissipation: 392 BTU/hour at 110/220 VAC Maximum Cisco 5500 Series Wireless Controllers Data Sheet: [URL]
Cisco Wireless :: Clarification On WLC License Files LIC-CT5508-UPG / PAK
Jan 28, 2013Basically I need to upgrade the license for Base-AP count to add 100 more AP's however my vendor has provided hardcopy of license as below:
-LIC-CT5508-UPG
-AIR-CAS-3KC-K9
-AIR-WIPS-AP-5
-L-NCS-1.0-100-ADD
My understanding is rigister LIC-CT5508-UPG/PAK number on cisco site and get .lic file however what is the use of other PAK where do i register this files with? Moreover , we do have NCS , MSE in place which is centralised devices.
Cisco Wireless :: Access Point And IPhone AIR-CT5508-K9 / Timed Out
Apr 1, 2012 i have setup of following AIR-CT5508-K9 controller and around 20 AP spread all over the place, two SSID one guest and one for my employees.
the one for guest has web authentication, using Iphone every 2 to 3 minutes it time out and i have to reenter the credentails for web authentication.
Cisco Wireless :: AIR-CT5508-K9 - VLAN Mapping Missing In LWAP
Mar 11, 2013I am running big wireless network, with 20no of 5500 with 7.0.116.0 version. I have more than 20,000 AP's. If i add some config in primary controller or do some changes or reboot all the AP's are moving to backup controller. this doesn’t have any problem, but many AP's which moved to backup controller are losing VLAN mapping. This happens every time. Primary --> backup, backup --> primary. Both controllers have same vern...same config etc..
AP model: AIR-LAP1252AG-A-K9
Controler model: AIR-CT5508-K9
Cisco Wireless :: AIR-CT5508 - Error (2048) Found In Fsck Check
Sep 4, 2011I get the following error message at startup.
---
Error (2048) found in fsck check - attempt to repair.---
What is the implication of the error message 106007? Do I have no problem continuing to be left out of this error?
Cisco :: Access Point (AIR-AP1141N-E-K9) Can Work With Wireless LAN Controller (AIR-CT5508-25-k9)
Feb 24, 2011I want to confirm if the access point (AIR-AP1141N-E-K9) can work with the Wireless LAN Controller (AIR-CT5508-25-k9)
View 2 Replies View RelatedCisco Wireless :: AIR-CT5508-K9 - AP01 Connection Bounce Due To WLAN Session Timeout
Jul 30, 2012When a client connecting to a specific AP (example AP01), after every 1800 sec uptime it will reconnect and join other unit AP (example AP02)Both AP physically installed distance is around 6 meters from each other. I conduct the testing where i get myself sitting in middle between these two APs.
01. If i disable settsion timeout this feature, or setting the seconds become higher value, what's the performance and security impact? Is it recomend to change the default 1800 seconds session timeout?
02. Is there anyway i can tweak on WLC controller to prevent the client after session timeout then associate with another AP. This will lead major performance impact as the client woudl possibility connect to the weak signal AP and effect on the performance.
These are the details for reference:Client detail
- Dell DW1520 wireless-N WLAN card, with firmware version 5.100.235.12
- CCX version 4 supported
- Layer 2 security is WPA2 personal with PSK.
- wireless radio an
Controller detail:
model is AIR-CT5508-K9
software version is 7.2.110.0
Cisco :: Change Management IP Of AIR-CT5508
Sep 25, 2011I want to change the management IP of our wireless controller, I have 5 LAP1142N connected to this controller.
I have a few questions before I will do this task.
1. If I change the management IP, will the controller need a reboot?
2. Will the AP's automatically sync with the new management IP?
3. Do I need additional configuration on the AP's?
4. What else do I need to consider.
Cisco :: Redundant Wlan Controllers (AIR-CT5508-50-K9)
Jun 11, 2012Q: a client has a network with 60 AP's controlled by a AIR-CT5508-50-K9 (+ L-LIC-CT5508-25A) with a redundant power supply. Can he get full redundancy by purchasing a second controller? If he purchases one, can he bring it into the network? What about the extra license for 25 extra AP's installed on the first controller?
View 4 Replies View RelatedCisco :: AIR-CT5508-50-K9 - WIPS Deployment Over WAN / HREAP
Jun 28, 2010I have this Wireless deployment :
Main Site: WLC AIR-CT5508-50-K9
WCS 6.x for 50 APs
(32 ) AP 1140
02 Remote Sites : 03 AP 1140 using H-REAP
Now, my company is considering to implement a wIPS solution, so i planned to install in the Main Site a MSE3300 and (01) AP 3500e as a wIPS AP Monitor in the remote sites,
Need to confirm:
A) Can an AP3500 work with HREAP and as wIPS monitor AP at the same time? or in other words, if it is possible to have an AP wIPS monitor far away from the WLC (over the WAN)?
B) What are the requirements of WAN link if I want to install a Centralized MSE 330 Engine,which perform the wIPS solution in all the network.
Cisco :: AIR-CT5508-K9 - Lightweight AP Loses Connection Every 10 Minutes
Oct 30, 2011Some of my Lightweight Access Points lose connection every 10 minutes now, it worked without problems before.
I'm using an AIR-CT5508-K9 Controller with Version 7.0.116.0 and AP are all AIR-LAP1242AG-E-K9.
In the log I find informations about my node changing his parent and then reseting the radio interface.
I checked my configuration, but perhaps I missed something.
7Mon Oct 31 14:35:11 2011AP's Interface:0(802.11b) Operation State Up: Base Radio MAC:00:3a:99:90:55:c0 Cause=Radio interface reset. Status:NA8Mon Oct 31 14:35:11 2011AP's Interface:0(802.11b) Operation State Down: Base Radio
[Code]......
Cisco Wireless :: Configure A Wired Guest Network With A Combination Of 5508 And 2504 Wireless Controllers?
Apr 7, 2013Is there any way to configure a wired guest network with a combination of 5508 and 2504 wireless controllers? I am aware that the 2504 does not have wired guest functionality, however is it possible to set up a wired guest on the 5508 and using mobility anchors, transmit the l2 information through eoip to communicate with the remote vlan?Home built NAC solution, using 802.1x authentication on switchports for public areas. If user is an employee, communicates with the supplicant on their machine, and places them on an internal vlan.If user is a guest, user fails 802.1x check and is placed on a "guest" vlan with an ACL and external DNS.If placed on the guest vlan, the user has to accept a terms of use form.This is working currently with our 5508s without any issue, however we have some remote offices we'd like to roll this out to that are using 2504 controllers. I'm hoping there's a way that I can use the 5508 as an anchor or vice versa to make this work.
View 1 Replies View RelatedCisco Wireless :: Wrv 210 To Configure Vpn Router
Jan 17, 2012how to config wrv 210 wireless-G vpn router config.
View 0 Replies View RelatedCisco Wireless :: AP541N How To Configure APs
Jun 19, 2011I have 3 AP541N. I become this not in a cluster. The APs standalone in the room. The first AP connect with cable to a DHCP Router from a other manufacturer. The other both APs should be connect over WLAN.How I must configure the APs? Which parameters must install?
View 1 Replies View RelatedCisco Wireless :: Configure A WDS With 2 WRVS4400N?
Feb 15, 2013In the note, i ve seen we can configure a WDS with 2 WRVS4400N, but i can't.How can i configure the 2nd WRVS4400N as repeater? Or can i configure it as Access point for another modem ?
View 1 Replies View RelatedWay To Configure Wireless
Apr 5, 2011i want to config wireless router but i don't now how it happen.
View 1 Replies View RelatedCisco Wireless :: How To Configure 3 X 4410N To Extend Wi-Fi
Oct 18, 2012I would like to configure 3 Access Point (WAP4410N) to extend the wifi in my house. I try it to do several configuration but it doesn't work.
In this configuration, the wifi devices disappears and re-appears constantly. I lose the IP addresses and they all come down only every 5 seconds. I made screen shots of the 3 terminals in the word document attached below
Cisco Wireless :: How To Configure Multiple WAP321 Wi-Fi At Once
Nov 26, 2012How to configure multiple WAP321 Wifi at once? Because I need to configure around 100 APs and i want to know if there is any software from Cisco to do it, like a WLC or something else.
View 6 Replies View RelatedCisco Wireless :: Can't Configure SSID More Than One In Web UI Of WAP4410N
Oct 12, 2011I can't configure the SSID more than one in the web UI of the WAP4410N. Except I can type the first SSID1, the rest SSID2 - 4 are grey which not allow me to type in anything. ( See attached the screen shot ) My current version is 2.02.1 and I was using IE8 under windows 7.
View 3 Replies View RelatedCisco Wireless :: Configure WLC 2112 With LAP 1042N?
Jan 4, 2012we are trying to configure WLC 2112 with LAP 1042 but getting following erros on LAP1042. It show the Ap is not supported in controller version 6.0.199.4
*Jan 5 16:52:13.397: %CAPWAP-5-DTLSREQSUCC: DTLS connection created sucessfully peer_ip: 192.168.2.101 peer_port: 5246*Jan 5 16:52:13.398: %CAPWAP-5-SENDJOIN: sending Join Request to 192.168.2.101*Jan 5 16:52:13.399: %CAPWAP-
[Code]....
Cisco Wireless :: Configure 1131 AP With 2 Ssids
Jun 15, 2012I have here a couple of APs with c1130-k9w7-mx.124-25d.JA1 loaded as firmware.
I want to configure them with 2 SSID: 1 encrypted, 1 public. Each should go to its own vlan, and thus should have a trunk towards the switch.
My wireless experience approaches zero however, and I cannot get the APs to even send out an unencrypted public SSID.
The config that is currently on the AP, after trying a lot of things is:
gibbs#show run
Building configuration...
Current configuration : 3272 bytes
!
version 12.4
[Code].....
Cisco Wireless :: Configure RV180W To Act As Bridge?
Jul 25, 2012I am trying to configure an RV180W to act as a wireless bridge to our guest wireless network (Cisco 4404 WLC, 1130AG access points, WPA2 personal). I was told in a Cisco support chat that this configuration was possible, now that I have the RV180W it doesn't seem that it is.
I've configured the RV180W as a WDS Bridge with the ssid name, WPA2 key, and MAC of an AP hosting the guest wireless but it still doesn't seem to connect. I have a feeling I would need another WDS device for this to work, and that it will not connect to just any wireless network.
using an RV180W as a wireless bridge?
Cisco Wireless :: Configure AIR-LAP1262N-A-K9 As Stand Alone?
Sep 12, 2012I am trying to configure this newly purchased AP to be used for WiFi surveys, heatmaps, etc..
I cant seem to get to the web interface of the AP to make config changes, even though it is picking up an IP via DHCP and it is pingable.
Cisco Wireless :: Configure 1941w Router AP
Mar 2, 2012Our boss decides to purchase 1941w Router & he asked me to do the necessary configuration. my knowledge in CISCO router is a CCNA level & i've never configured an embedded AP or ADSL line on a router before.
the topology is as the following: as for the wired Network, we have one LAN (192.168.1.0/24) connected to GE0/0 (192.168.1.254/24) on router & has the ability to access the internet which is ADSL configured as ATM0/0/0
As for the wireless network ( now here is the problem) what i want is the following:
I want the wireless network to share the same network with the wired which means 192.168.1.0/24 i want to use WPA encryption how to configure the AP?!
this is a true challenge for me. After a lot of searching, most of the sample configuration over there is about creating two VLANS!!! & two DHCP Pool.
Cisco Wireless :: Configure NTP Server On ACS 5.3 Through GUI Mode
Aug 27, 2012I need to configure ntp on acs5.3 ,i dont know how to configure through gui mode,
View 1 Replies View RelatedCisco Wireless :: Possible To Configure WDS C1131 AP Also As Infrastructure AP
Mar 16, 2013I've setup the WDS and Infrastructure AP according to Document ID: 68098
1. The Infrastructure AP is registered and active in WDS AP.However, any client device such as NB or PDA cannot obtain IP address.In WDS AP the client device is shown as authenticating all the time. What I missed? Or there is somethig else need to be set?
2.Can I configure the WDS AP alslo as Infrastructure AP?I mean, to be WDS and Infrastructure at the same time, broadcasting the SSID etc.?