Cisco Wireless :: Configure RV180W To Act As Bridge?
Jul 25, 2012
I am trying to configure an RV180W to act as a wireless bridge to our guest wireless network (Cisco 4404 WLC, 1130AG access points, WPA2 personal). I was told in a Cisco support chat that this configuration was possible, now that I have the RV180W it doesn't seem that it is.
I've configured the RV180W as a WDS Bridge with the ssid name, WPA2 key, and MAC of an AP hosting the guest wireless but it still doesn't seem to connect. I have a feeling I would need another WDS device for this to work, and that it will not connect to just any wireless network.
using an RV180W as a wireless bridge?
View 4 Replies
ADVERTISEMENT
Oct 14, 2012
I recently bought one RV180W and two WAP121 in order to make a wireless extension of a network.I configured RV180W as Router and the three of them have the same SSID and password.Also, I added in RV180W WDS configuration both MAC Addreses of WAP121's and in WAP121's WDS configuration the MAC Address of RV180W.Even I tried in WAP121's with and without encryption using the same WPA Key of the RV180W.
The thing is that is not working at all. They work great separately but right WAP121 can't stablish WDS link with RV180W neither do the left WAP121 with RV180W.I tested WDS configuration of WAP121's and they can see each other between them using standard WDS configuration, so I assume that WDS function of WAP121's works great.Finally I try the same config but setting RV180W in WDS Bridge and WDS Repeater without any different result.Do I have any chance to make the topology I showed up would work? How do I have to configure the RV180W and WAP121's?
View 1 Replies
View Related
May 26, 2013
a customer got an 1552 outdoor AP in local mode and installed it at a building. It has to run as a Mesh AP (MAP). Now the AP connects one time to the WLC 5508 and started a download. After that, the AP never came back. Like we saw on the other installed 1552 RAP's, they all where in local mode.We configured all AP's to bridge mode, but the MAP could not join anymore.Is there a CLI command to change the mode on the AP itself?From the WLC it's not a problem, but for the AP CLI I cannot find sth.
View 1 Replies
View Related
Jun 8, 2012
Can the rv120W be configured as a wireless bridge? We have a need to configure a vpn connection to a remote building but will need to connect the router via an existing wireless network.
View 4 Replies
View Related
Jun 16, 2011
I want to configure two AP WAP4410N in Bridge Mode and I don´t find the correct configuraction tips.
View 11 Replies
View Related
Nov 21, 2011
I have a pair of Aironet 1310's I am needing to bridge. I have used the CLI to configure the BVI1 with the ip address and verified it. I then tried to access the GUI to configure the device via Internet Explorer and it would not provide access. I read that it had to be older versions of IE but my OS will not support older versions. I then downloaded Netsace Navigator 7.01 as indicated, but still did not get access.
Then I thought maybe if I can access the GUIvia the IPSU tool but I have Googled the Cisco IPSU and cannot find a downloadable link.
View 3 Replies
View Related
Apr 21, 2013
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
View 3 Replies
View Related
Dec 15, 2012
I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
View 9 Replies
View Related
Jan 25, 2012
My client has a DSL modem and a Belkin wired 4-port router configured to connect to it using PPPoE. Apparently there is no way to configure the E2500 such that it may be dropped in as a direct replacement for the Belkin (which would also provide wireless access) without the PPPoE login/password (from the DSL provider, Verizon).
I would like to connect the "Internet" port of the E2500 to one of the Belkin's 4 ports, in order to use the E2500 for wireless internet access without using any of the 4 wired ports but I think this creates a NAT within an existing NAT network?
To avoid that if I configure the E2500 in wired bridge mode, it becomes transparent, and I can no longer access its administration interface using the address 192.168.1.1 (since that address belongs to the Belkin). How may I, for example, change the wireless password which the E2500 is in wired bridge mode?
View 1 Replies
View Related
Sep 5, 2011
I have 12 wap4410n to enable wireless connection to a school building with 3 floor. I planned to configure one as a Access point. My doubt is in which AP mode i have to configure the rest as WDS Bridge or WDS Repeater other mode. In each access point i have Ethernet connection to the switch.
View 1 Replies
View Related
Dec 24, 2011
Can this router be set up as a wireless bridge?
View 1 Replies
View Related
Apr 24, 2011
Configure 1310 point-to-point bridge (AIR-BRI1310G-A-K9-R)
View 3 Replies
View Related
Aug 1, 2011
Is it possible to configure bridge mode in asa 5505 if it is can u provide me a config.
View 1 Replies
View Related
Jan 31, 2012
I need to configure a WAG 120 N as a bridge, so I can have my public IP as an output of an Ethernet port. I need this configuration because I have a non ADSL router managing VPNs and needs the public IP on the WAN port of this router.
View 3 Replies
View Related
Sep 20, 2012
I am new to cisco ASA. I need to configure ASA 5520 in transparent bridge mode. [code] I need to place the new asa firewall in transparent mode. How to configure the firewall in transparent bridgmode.
View 5 Replies
View Related
Feb 16, 2011
I want to achieve the following setup:
So basically I have a C877 and a Cisco ASA 5505 and I want to push the public IP of the ISP to the outside interface of the ASA so the Cisco 877 will only be responsible for ADSL and PPPoA. Don't ask me why I don' t use a modem/router instead. I know that is a waste to use the C877 in this way but I want to test the setup.
Right now the config of the C877 regarding ADSL and PPPoA looks like that ( I don't have the ASA connected yet, so all the PC are connected directly to the C877 right now):
interface ATM0 no ip address load-interval 30 no atm ilmi-keepalive pvc 0/35 encapsulation aal5mux ppp dialer dialer pool-member 1
interface Dialer1 ip address x.x.x.x 255.255.255.248 ip access-group OUTSIDEACL in ip nat outside ip inspect FWRule out ip virtual-reassembly encapsulation ppp dialer pool 1 ppp authentication chap pap callin ppp chap hostname xxxxxxx ppp chap password 0 xxxxxxx ppp pap sent-username xxxxxx password 0 xxxxxxx
ip route 0.0.0.0 0.0.0.0 dialer 1
ip nat inside source route-map Nat interface Dialer1 overload
interface vlan 100 is my LAN configured with DHCP.
how I should configure the C877 to push the public IP to the ASA?
View 6 Replies
View Related
Aug 23, 2011
My apartment already has internet provided to all of the rooms, but I'm trying to set up my router as a wireless access point. I tried disabling DHCP on the router, but then I wasn't able to get any internet access at all. Does this device not support bridge mode?
View 5 Replies
View Related
Jan 1, 2013
We have a RV120W Wireless-N VPN Firewall and we want to configure the router in brigde mode (transparent). Because we have another Firewall, use for filtering and default gateway on the LAN. The ISP provide IP address by DHCP, so we must connect the internet connexion to the WAN interface. But How can we do for connected the RV120W to our firewall? The router mode on the RV120w allows-it to make this configuration?
View 1 Replies
View Related
Apr 21, 2007
I'm trying to configure my WAG200G to work in bridge mode so that it can transfer my external IP address to my ISA server.My network map is very simple,Internet -- WAG200G -- ISA Server -- LANCan
View 7 Replies
View Related
Sep 7, 2012
config to setup PPPoE on the cisco 831 router to be used with a modem in bridge mode. I have tired other peoples configs found on the web but, not all the commands were available on the IOS version thats on the router. Also note that I bought this as a used router and I dont have a service contract so I am unable to download an updated IOS. The router ver is 12.3(7)T9 and the IOS is c831-k9o3sy6-mz.123-7.T9.bin. Running config below is last tried still could not connect or get ip address from isp. [code]
View 2 Replies
View Related
Apr 20, 2012
I am trying to configure a newly installed HWIC-4ESW on a 2811 router to bridge to the FE 0/0 interface. Currently, I have a cheap switch connected to FE 0/0 which in turn connects to all the phones, however now I just want to connect all the phones to the HWIC and have it internally bridge to FE0/0 for the connectivity to CME, etc.
View 5 Replies
View Related
Oct 6, 2012
I recently replaced my working WRVS4400N v2 Router with an RV180W. Unfortunately I am now stymied, as I am unable to use WDS to connect my WAP4410N to the RV180W to fill a dead spot. I tried calling support (case # 623405011) but we were unable to get communications working correctly - even when the two devices were less than 5 feet apart. The engineer's final suggestion wwas to put the WAP4410N bact to factory default, connect it to a laptop, and compare settings side-by-side...thats 2 hours of my life I will never get back as it was a useless endeavor. The WAP4410N is on 2.0.5.3, and the RV180W is on 1.0.1.9 (Both are on the latest available firmware).
My question would be what Cisco device would be best matched with this RV180W so I can use WDS and fill in the hole. I have no problem, just as long as it works and stays stable, as I had with the WRVS4400N / WAP4410N setup. Optionally, is there some other setting the engineer missed? The RV180W is my gateway router and primary wireless access point, I just need to fill some spaces where there is interference.
View 20 Replies
View Related
Mar 17, 2013
I just purchased a RV180W wireless router. It came with 1.0.0.30 firmware revision installed.
I have tried from multiple computers and multiple browsers to update the firmware on this unit, and I always end up with the same result.
"Firmware file is invalid or corrupted"
I have also downloaded the images (1.0.1.9 and 1.0.2.6) from multiple machines all with the same result.
View 2 Replies
View Related
Oct 7, 2012
I have an RV180W Wireless-N with firmware# 1.0.1.9 The problem is that any Macintosh computer will not work with the wireless network.The problem is consistent with several MacBook laptops, running Leopard, Snow Leopard and Mountain Lion.The MacBook connects with the wireless network and obtains an IP address.However when the MacBook tries to access a web page, it fails loads.Accessing LAN assets like network volumes and printers works fine.All mobile devices, such as iPhones, iPods and iPads work fine.I have tried numerous wireless settings on the router and the MacBooks and nothing works.The problem happens regardless of what kind of wireless security is present.There is not MAC filter.
View 1 Replies
View Related
Jan 18, 2013
This router keeps dropping all connections under a load of about 30 devices. everyone will lose internet access for a few minutes until it comes back. All settings are correct.This doesn't happen unless around 20-30 users are actively using their connections, both wired and wireless.
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] IP: 68.84.158.86
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] BCAST: 255.255.255.255
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] SUBNET: 255.255.254.0
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] GW: 68.84.158.1
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] DNS1: 75.75.75.75
[code]....
View 1 Replies
View Related
Feb 7, 2013
I've just bought a Cisco RV180W and I am trying to find its newest firmware but I am getting 404 everytime I access or search for this updates.
View 1 Replies
View Related
Mar 6, 2013
We have the RV180W router and the WAP321 access point in our business. We want to broadcast two SSIDs from both locations: the office SSID, which shares routing to LAN traffic, and a guest SSID.The office computers are attached via ethernet to a switch off of LAN port 1 on the router. The AP is attached to LAN port 2 on the router.On the router, the office SSID and the LAN are members of VLAN 1. The guest network is a member of VLAN 2. From the router, everything works just fine.On the WAP, the staff SSID works fine, but the guest SSID has no internet. Both the office and guest networks get DHCP successfully from the router.Our VLAN membership table in the router and WAP are attached, as well as other configuration details.Why would we not be getting internet on the guest ID only on the WAP?
View 8 Replies
View Related
Dec 19, 2012
Right now the Self-signed Certificate on my RV180W generates errors as it was issued to the MAC address instead of the current IP address. Need instructions on Generating a Self-Signed certificate (or 1 from my Windows Server 2012 Certification Authority) that will eliminate the constant barreage of certificate errors I get when trying to access the management interface of my device? the internal domain is mythos.local, netbios name of MYTHOS, and the device name in question is surtur.
View 2 Replies
View Related
Jun 5, 2012
I am trying to download firmware for an RV180W Wireless-N Multifunction VPN Firewall Router. I found updates for a 110 in BIN format (router only updates from IMG). Currently running stock firmware on that router and need the update.
View 2 Replies
View Related
Mar 22, 2013
How to use WAP4410N repeater Router Mode RV180W wireless network. until now it's still not working.
And the bottom line is I want keep RV180W in Router Mode,not WDS Bridge or WDS Repeater mode.
During the search I find that WAP4410N WDS Repeater is not compatible with RV180W,but I'm not sure about that, so how to configure it
My goal is use two WAP4410N expand RV180W Wifi Range that can cover the dead spot in my office.
View 1 Replies
View Related
Jul 25, 2012
I recently purchase my first Cisco products for a network for our church. I have a RV180W router, WAP 121 Access Point and a SR2016T switch for our network, which is just pier-to-pier at this point. We have 5 computers connected with ether net through the switch and all see the Internet and work fine. The wireless connection through the router is working fine with our wireless devices (laptops and i Pads). Where I am having issues is with the AP. It is in different area away from the router being powered through POE instead of the regular power connection.
My problem is this: it takes FOREVER to connect to the AP and to the Internet, even when sitting directly under the AP with full signal. Once connected, it appears to allow Internet connection just fine, but getting to that point takes 15-20 minutes sometimes. Also, when I come back the next day, I have NO signal at all, as it seems the AP has "timed out" due to inactivity or something. I have to reboot the AP and the router to get it all back up and running again. I need for the signal to stay up all the time or at least come on when someone connects.
So, what am I doing wrong here? I have recognized and authorized the AP through the router config, security is set up fine and I can see it once it comes up. I have the AP set up as a completely different SSID, although I would prefer to have the AP as merely an extension of the router's wireless network if possible.
View 5 Replies
View Related
Apr 24, 2012
Can I associate the non-root bridge model 1310 to the root bridge model 1400? Is there any problems on the configuration I need to be aware of?
View 7 Replies
View Related
Mar 15, 2013
I installed the RV180W yesterday and decided to play with it a bit today. I got stuck on the firmware update. Tried different browsers on different PC's. Tried going to 1.0.1.9 first. I have the "reset all configurations" button checked. After looking through the posts here I'm not sure this firmware will even fix my next few problems(port forwarding etc). Is there a trick with this device?
View 4 Replies
View Related
