Cisco Wireless :: RV180W - Generate Proper Self Signed Certificate?

Dec 19, 2012

Right now the Self-signed Certificate on my RV180W generates errors as it was issued to the MAC address instead of the current IP address. Need instructions on Generating a Self-Signed certificate (or 1 from my Windows Server 2012 Certification Authority) that will eliminate the constant barreage of certificate errors I get when trying to access the management interface of my device?  the internal domain is mythos.local, netbios name of MYTHOS, and the device name in question is surtur.

View 2 Replies


ADVERTISEMENT

Cisco Wireless :: Proper WDS Extender For RV180W

Oct 6, 2012

I recently replaced my working WRVS4400N v2 Router with an RV180W. Unfortunately I am now stymied, as I am unable to use WDS to connect my WAP4410N to the RV180W to fill a dead spot. I tried calling support (case # 623405011) but we were unable to get communications working correctly - even when the two devices were less than 5 feet apart. The engineer's final suggestion wwas to put the WAP4410N bact to factory default, connect it to a laptop, and compare settings side-by-side...thats 2 hours of my life I will never get back as it was a useless endeavor. The WAP4410N is on 2.0.5.3, and the RV180W is on 1.0.1.9 (Both are on the latest available firmware).
 
My question would be what Cisco device would be best matched with this RV180W so I can use WDS and fill in the hole.  I have no problem, just as long as it works and stays stable, as I had with the WRVS4400N / WAP4410N setup. Optionally, is there some other setting the engineer missed?  The RV180W is my gateway router and primary wireless access point, I just need to fill some spaces where there is interference.

View 20 Replies View Related

Cisco :: Can LMS 4.0 Use CA Certificate Instead Of Self-signed

Apr 4, 2012

I've been reading over the documentation, but only see instructions for using a self-signed certificate for SSL.  Or even trusted certificates between LMSes.  But I can't seem to find anything on LMS 4.0 using a Certificate Authority.  And I have a security requirement to do so.
 
Is this possible in LMS 4.0?

View 3 Replies View Related

Cisco VPN :: 871 - Import A Self Signed Certificate

Sep 27, 2012

Can I import a self signed certificate from a Cisco 871 router to a Cisco ASA 5505? The 5505 replaced the 871 and I have a VPN that goes to another company that we have a connect to. The device on the other end is a VPN concentrator ( I do not have access to modify this device without going through multiple channels.) I only need to mimic this device for the site to site VPN tunnel only. It appears that there are no pre-shared keys only a self signed certificate.         

View 1 Replies View Related

Cisco :: ACS 5.3 / Self Signed / Certificate Base Authentication

Oct 17, 2012

Our ACS (5.3) has self signed certificate, we have exported it and declared it in Certificate Authorities.We have exported it to have a Trusted Certificate for client machine.
 
This certificat has been installed on a laptop.The wlc is successfully setup for eap (peap & eap-fast has been tested > ok)I have this error in the log:
 
12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in  the client certificates chain.I think the Access Policies (identity & authorization) are misconfigured: [code]

View 1 Replies View Related

AAA/Identity/Nac :: ACS V5.2 New Self Signed Certificate Not Showing In Browser

Nov 11, 2012

I have just renewed the self signed certificate on a v5.2 ACS and expiry date of 2013 is showing in the ACS GUI. However, when I start an ACS Admin session and view the certificate information in the browser it is showing the old expiry date of 2010. I have tried this in IE and Firefox and the certificate information is the same.
 
Is there a way I can get the browser to pick the new certificate ?

View 1 Replies View Related

Cisco :: 5508 Unable To Upload Signed Certificate

Jul 1, 2012

I have two Cisco WLC 5508 controllers that I'm trying to set-up for our new corporate WLAN. I've gone through most of the configuration fine but have ran into an issue uploading a signed certificate to one of my controllers. I should point out that I have managed to upload the certificate successfully to one of the controllers, I just can't seem to upload it to the second.The issue is as follows:
 
- I've logged into the controller, gone to Security -> Web Auth -> Certificate -> Download Certificate
- I've specified my tftp server details and selected apply
- the process begins and I can see through my tftp client that the controller is attempting to copy and install the certificate
- The controller tries to install the certificate but fails, reporting the same

View 9 Replies View Related

Cisco :: 2048 - Self-Signed Certificate And Init 6 Process

Feb 16, 2012

I have a doubt about CiscoWorks. I need to generate the self-signed certificate with a key of 2048 bits to generate a CA with VeriSign. CiscoWorks do this automatically with a key of 1024 bits and I do not find a form to elect a a diferent key. Is it possible to generate a certificate with 2048 bits key?

Another problem is that I have CiscoWorks installed on Solaris. Many times at day the web application does not work and the only way to recuperate it is with the command "init 6" and I have to way 15 minutes until I can have access again. Why is produced this error? Who can I fit it?

View 1 Replies View Related

Cisco Routers :: RV120W - Create New Unique Self-signed Certificate?

May 9, 2012

how to create new unique self-signed certificate on RV120W? I can create request for singning by external CA, but I cannot create new unique self-signed certificate itself.

View 2 Replies View Related

Cisco Routers :: Self-signed Certificate With RV220W And QuickVPN Client?

Nov 21, 2011

The establishment of IPSEC tunnel between the RV220 and QuickVPN client works properly with the security certificate of origin of the router.RV220 V1.0.3.5QuickVPN V1.4.2.1
 
Since the establishment of a security certificate self-signed, the RV220 and QuickVPN client refuses to work together .

Here are the log of the QuickVPN client

2011/09/27 12:45:14 [STATUS]OS Version: Windows 7
2011/09/27 12:45:14 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON

[code].....

View 4 Replies View Related

Cisco Firewall :: ASA5520 HTTPS SSL Certificate Signed Using Weak Hashing Algorithm

Oct 18, 2011

I am support one client for,  whom falls under Security  scans mandatory for new implementation of ASA 5520 device.  The client uses Nessus Scan and  the test results are attached.The Nessus scanner hit on 1 Medium vulnerabilities.

View 2 Replies View Related

Cisco Firewall :: How To Generate A CSR File To Renew Out SSL Certificate On ASA 5510

Jun 13, 2013

How to Generate a CSR File to Renew out SSL Certificate on ASA5510 v9.0(2) - ASDM v 7.1(2) ?

View 1 Replies View Related

Cisco VPN :: 2811 / How To Generate And Write A Clients Certificate On Etoken

Sep 28, 2011

I need:

cisco 2811 IOS CA as server
cisco vpn client + etoken (aladdin) as client
 
certificate enrollment from cisco vpn client and vpn connection with it works at present, but I don't know how to use etoken with it, how to write the client's cert. to a token.i used this doc:Configuring IPSec Between Cisco IOS Routers and Cisco VPN Client Using Entrust Certificates[URL]in chapter "Certificate Enrollment for the Cisco VPN Client", in section 3 there is a screenshot with an example of a certificate enrollment, where the specified name (CN) as vpnclient, but in section 5 "view the certificate ", common name specified as Joe Smith, etc.where this client's data is obtained? it's not clear to me... how to generate and write a client's certificate on etoken, who uses cisco vpn client with it for connect to server?

View 1 Replies View Related

Cisco AAA/Identity/Nac :: ACS 5.1 - How To Generate Certificate Signing Request On Secondary

Oct 3, 2012

I have a pair of ACS appliances running 5.1 code. The appliances are set up as a replicated pair. I have valid local and trusted certificate authority certificates on the primary.

The trusted certificate authority certificate gets replicated to the secondary. Obviously the local certificate doesn't get replicated. I need to generate a certificate signing request on the secondary but it doesn't seem to allow you to do it.  

View 1 Replies View Related

Cisco Routers :: RV180W - Any External Source IP For RV180W DMZ?

Apr 21, 2013

I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.

View 3 Replies View Related

Cisco Routers :: Difference Between RV180W-E-K9-G5 And RV180W-A-K9-NA?

Dec 15, 2012

I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A.  As far as I know -A is the compliance code for Philippines.  Am I right?  If yes, what about -E?  There is a documentation for wireless complaince on Aeronet devices but what about these SB products?

View 9 Replies View Related

Linksys Wireless Adapters :: WMP300N V2 Drivers Not Digitally Signed

Apr 27, 2012

Yesterday I contacted live support with the problem that my network driver is crashing and giving me BSODs because of this when my download speed reaches above 5.5MBps.[url]...When I try to install those drivers, I first get a warning that the drivers aren't signed. I press "Continue" to dismiss the message but still at the end it fails to install and gives me the message "The drivers can not be loaded because they are not digitally signed", leaving you with a useless device.I bypassed the check windows is doing by turning off the check by running Windows in "Test Mode". I have test-signed the drivers myself that allowed me to install them. Now my device is working and not giving me BSODs anymore.
 
What I want is the drivers to be digitally signed by linksys/cisco. I think it's very unprofessional to distribute unsigned/useless drivers to customers. I am lucky that I am somewhat more experienced with this stuff, but what about people that are not? I think everybody should be able to install the latest drivers without any problems, without the need to hack into windows.I hope to see new drivers soon, or the same drivers but then digitally signed so I can turn off "Test Mode" again removing this ugly watermark in the bottom right corner.

View 9 Replies View Related

Cisco AAA/Identity/Nac :: %ASA-3-717009 / Certificate Validation Failed / Certificate Date Is Out-of-range

Jan 30, 2012

There is ASA with remote access VPN and users are authenticated using third party signed certificates (CA is not local in ASA).When user certificate expires i can see it in syslog messages. For example:
 
     %ASA-3-717009: Certificate validation failed. Certificate date is out-of-range, serial number: (...)
 
I would like to know if there is an opportunity to view user's certificate expiry date beforehand, say, 3 days before?

View 3 Replies View Related

Unable To Get Proper Speeds Via Wireless

Jan 15, 2013

Had Infinity installed yesterday which means we're up from our awful 3mb speeds to around 35ish. A partner in my household is using a laptop downstairs and it's getting the full speeds, no problems.

However, upon plugging in a wireless adapter upstairs in a PC, it's not getting the full speeds, not even close. A mixture between 1mb and on one occasion about 8mb. The speedtest is showing something like 400ms too. I stick a wire into the PC and it's fine, around 30 or so ms and hitting the full speeds available. The wireless adapter is a Phillips, never really had any problems with it before, not that I know of anyway.

View 1 Replies View Related

Cisco Wireless :: Power 1552e With Proper Poe Injector?

Oct 13, 2012

Can I power the 1552e with the proper poe injector if I am not using the ethernet port for backhaul? I want to get power thru poe but use a fiber for backhaul.

View 4 Replies View Related

Cisco Wireless :: WLC 7.0 - Unable To Generate Heatmap On WCS

Apr 14, 2011

I have a WCS server running the version 6.0.170.0. I have already added few WLCs running the version 7.0  to this WCS. It is working fine. And now I have added two new controllers running the version 7.0.98.0 to the existing WCS server. When i add the floor layouts to the WCS and position the access points from the new controllers, the heat map is not generated automatically.

View 2 Replies View Related

Cisco AAA/Identity/Nac :: ISE 1.1.1 Don't Have Certificate Authority Certificate Anymore?

Oct 19, 2012

i am working on ISE 1.1.1, surprisingly i couldn't found certificate authority certifiate at certificate operation anymore.
 
would it be the change on GUI? So now where i can import the CA certificate to ISE?

View 5 Replies View Related

Generate Password For Wireless Connection?

Feb 27, 2012

do we have anything like universal password for cracking through wireless connection?

View 3 Replies View Related

Cisco Wireless :: 2504 Controller - How To Generate Graphs

May 19, 2013

I'm supporting a 2504 wireless controller with 3 aps in a health clinic.  I'm interested in generating some useful information for the owners of the device such as radio utilization (It'd be really nice if there were some graphs). how I can generate these graphs without SNMP monitoring or something like Cisco Prime Infrastructure?

View 4 Replies View Related

Linksys Wireless Router :: E4200 With Proper Throughput?

Feb 12, 2012

I have an E4200 running firmware v1.0.03.Works fine for a period of time (might be hours, might be days) then throughput drops to something in the range of 1-3M when typically I'll see 6-8M (DSL).  I can reset the DSL modem, hubs, etc but the problem isn't fixed until I reset the E4200; so I've pretty much narrowed it down to the router.

View 1 Replies View Related

Linksys Wireless Router :: E2000 - Way To Get Proper Internet Connection

Sep 13, 2011

Internet was working great a few days ago with my e2000 and comcast as my ISP.  I've got a few devices connected through ethernet connections on the unit.  We also connect to the e2000 wirelessly.Problems started yesterday with no internet.  Last night I rebooted everything and still nothing works. Connected laptop to cable modem directly.  Wasn't getting internet connectivity so I called Comcast.  They reset my modem and everything started working fine.  Now I can directly connect from cable modem to laptop and internet works fine.  I try connecting the modem to the router and still no internet.

View 2 Replies View Related

Linksys Wireless Router :: WRT54G - Getting Connection And Proper Working?

Sep 8, 2012

I have 2 laptops in my home, I had no problem getting one to connect to the internet. The second one I'm having trouble connecting, I am wireless, I didn't have a problem at my old house with another laptop connecting to the internet with this router. I'm trying to save myself some money by not going through my wireless company, and end up having to get their router, which I already have their modem.

View 1 Replies View Related

Linksys Wireless Router :: E3200 - Wifi Doesn't Work In Proper Way?

Aug 19, 2012

Buy new one Linksys E3200.  Two day using and now have such problem. Every 30 minutes WiFi connection disappears for 10-15 sec. Then appear, but you can't connect to WiFi network for next 30 seconds. Update firmware of router to last version, but it doesn't work.

View 3 Replies View Related

TP-Link Dual-Band Wireless :: WDR4300 Doesn't Generate Any IP Address

Dec 25, 2012

Region : Brazil
Model : TL-WDR4300
Hardware Version : V1
Firmware Version : 3.13.23 Build 120810 Rel.44064n

First of all, by connecting the router to my desktop through wire, it doesn't generate any IP address, except for 169.254.x.x.. I already tried configuring the IP to static mode, but nothing changed, I can't even access the router's interface, however, if I try the same thing (connecting the router through wire) with my notebook and netbook, I get the IP without any problems.

The second problem is related to the wireless connection. When I try to connect my smartphone (Motorola XT860) I get the IP normally and supposedly internet connection, however the connection only lasts for a few seconds, after that I am incapable of accessing even the router's interface (again). If my smartphone stays connected to the router, nothing else works even for other connected devices, but when I disconnect my smartphone, all the other connections resume as if nothing happened. I already tried changing the Beacon Interval, the Address Lease Time, and so on, but nothing has worked.

View 14 Replies View Related

Cisco :: Upload Signed Certification To LMS 4.2.2

Oct 14, 2012

I would like to upload the signed certification to LMS 4.2.2.After checking ( 4. option ) I choosed the 6. option  and press "y" for questions and the perl script is freezing.  

View 2 Replies View Related

Cisco VPN :: Using A Publically Signed Cert On ASA 5505

May 1, 2013

I am wanting to use a cert signed by a digicert or verisign on my ASA so that anyconnect doesn't frreak out with the untrusted cert. I have created the CSR, and I uploaded the certificate, but it is still showing the old self signed untrusted cert.

View 5 Replies View Related

Cisco Firewall :: Installing Signed Certificates Into ASA 5510

Apr 18, 2012

I am running Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.4(1).  This will be used as a VPN gateway.  I am having troubles installing our cert.  I can install the cert, but it never connects witht he correct key.  It references trustpoint0 when it is trustpoint1.  I deleted all trustpoints and it still happens.  That.vpngw4# sh run | begin rustcrypto ca trustpoint ASDM_TrustPoint0crl configurecrypto ca trustpoint ASDM_TrustPoint1keypair ASDM_TrustPoint0crl configurecrypto ca certificate chain ASDM_TrustPoint1certificate 0f8e62    308203d5.8c  quitI deleted both trust points and when I do a  sh run both are gone, but when I then import the cert (via ASDM) it creates trustpoint0 again.

View 3 Replies View Related

Cisco Security :: How To Renew Self-Signed ACS 3.3 Cert Used For PEAP

Mar 29, 2006

We currently are using a self-signed cert (for PEAP machine authentication) that was created on an ACS 3.3 appliance.  That cert was manually installed on our laptops when they were configured for wireless conenctivity.My problem is, that self-signed cert will soon be expiring and I am not sure what needs to be done to issue a new cert AND deploy it to my Windows XP Pro clients without a service interruption.  If possible, I'd like to leverage our exsiting AD infrastructure for this, but I need some direction, and time is of the essence!!

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved