I am wanting to use a cert signed by a digicert or verisign on my ASA so that anyconnect doesn't frreak out with the untrusted cert. I have created the CSR, and I uploaded the certificate, but it is still showing the old self signed untrusted cert.
View 5 RepliesWe currently are using a self-signed cert (for PEAP machine authentication) that was created on an ACS 3.3 appliance. That cert was manually installed on our laptops when they were configured for wireless conenctivity.My problem is, that self-signed cert will soon be expiring and I am not sure what needs to be done to issue a new cert AND deploy it to my Windows XP Pro clients without a service interruption. If possible, I'd like to leverage our exsiting AD infrastructure for this, but I need some direction, and time is of the essence!!
View 2 Replies View RelatedI installed a chained SSL cert on our anchor/guest 4402 a few years ago.We now have a need to replace the 4402 w/ a 5508, and I got everything configured, ready to go, except that darn cert.I can no longer locate the private key that was used to sign the original CSR.Is there any way to export the current cert from the 4402, so that I can import to the 5508? Or am I SOL?
View 3 Replies View RelatedI've been reading over the documentation, but only see instructions for using a self-signed certificate for SSL. Or even trusted certificates between LMSes. But I can't seem to find anything on LMS 4.0 using a Certificate Authority. And I have a security requirement to do so.
Is this possible in LMS 4.0?
When trying to do a cut-n-paste enrollment of a cisco 3725 router with a microsoft windows server 2003 CA i get the following error on the CA.Certificate Services denied request 8675 because The request subject name is invalid or too long. 0x80094001 (-2146877439). The request was for OID.1.2.840.113549.1.9.2=rtr31slied3.unit4agresso.com. Additional information: Error Constructing or Publishing Certificate This is when i use the router or webserver certificate.The only template that does work is the user certificate but then you get error messages that the router name doesnt match the cert name.The 3725 is running ios version 12.3(14)T3.How can we get the right templates to work ?
View 3 Replies View Relatedhow to install a wildcard certificate with only the .cer file. I've found quite a few things here in the forums, but everyone seems to also have a pkcs12 file, which I do not.
This is an ASA 5510 on ver 8.4.
I know that CSRs cannot be generated with multiple names, but if the SAN is added after the cert is ordered from Geo Trust, Veri sign, etc. can the CSS support using the cert?
View 1 Replies View RelatedCan I import a self signed certificate from a Cisco 871 router to a Cisco ASA 5505? The 5505 replaced the 871 and I have a VPN that goes to another company that we have a connect to. The device on the other end is a VPN concentrator ( I do not have access to modify this device without going through multiple channels.) I only need to mimic this device for the site to site VPN tunnel only. It appears that there are no pre-shared keys only a self signed certificate.
View 1 Replies View RelatedI would like to upload the signed certification to LMS 4.2.2.After checking ( 4. option ) I choosed the 6. option and press "y" for questions and the perl script is freezing.
View 2 Replies View RelatedI have a need to utilize two factor authentication using a machine certificate and users AD crednetials. What we would like to do is to have the ASA and AnyConnect verify the certificate exists, check against our in house CA for validity, if valid pass the user credentials to the AD servers and establish the tunnel. If not valid quarantine the session and pop a message to the user to contact the help desk ASAP. My guess is the following (using ASDM 6.6, ASA 8.6.1, ASA 5545-X):
1. under the connection profile I have select BOTH for authentication and added a AAA server group.
2. under Cert Management I have added the 3 certs that are present on all company mobile assets
- Cert America
- Cert Europe
- Cert Root
3. I have an identity cert installed from the company CA and it is selected as the device cert under connection profiles
4.Local Cert Authority is Disabled
5.Under Remote Access>Advanced>Certs for AnyConnect>
- I have mapped DefaultCertifiateMap pri 10 to Company_Cert connection profile
- The mapping is looking for Subject: CN: <Contains> (string) ----where string is a common component of each Cert listed in #2.
Question #1 - Is this correct for utilizing certs and AD auth or have a missed any steps?
Users are directed to a an initial installation URL - where the AnyConnect client performs the installation and passes down the intial AC profile which auths using only AD creds. On subsequent connections users who pass the certificate mapping check are migrated to the connection profile which uses the dual authentication method.
Question #2 - When I attempt a new installation of AnyConnect using the two factor URL . I receive an error "certificate validation error" and the installation fails - for the life of me I can not figure out why???? The machine has all three certs, using IE9 as the browser.
I am basically looking to install the wildcard on the outside interface for my ASA
View 1 Replies View RelatedI have a cisco 5508 WLC that I have setup WebAuth on and trying to install the certificate on. I have generated the csr and gotten my cert from Verisign (X.509, server platform=apache). I have followed the instruction via the cisco documentation url...I found an error in uploading and find out how to encrypt mykey: url...
I am also having exactly the same issue with a certificate from Thawte. I followed the unchained guide and have tried both with and without a password in the initial step key generation step, requesting a new cert each time. As with Jeensernchew's issue there are no errors in OpenSSL but when uploading the cert to the WLC get the following error. [code] The WLC is running version 6.0.196.0. I am using OpenSSL 1.0.0 29 Mar 2010.
When I requested the cert from Thawte I was asked to specify the device type, I chose Cisco, but as all the work and conversion is being done by OpenSSL, should I have chosen differently? When I do this I can load the cert in the 5508, but the controller fails and doesn't allow that VLAN or config access to the wireless network. I am at a loss of why I can load and it not work. I have verified my hostname and password and those are good.
I've seen a bunch of discussions on the untrusted server cert error with self signed certs. But I have a valid wildcard that I use on my ASA. How do I make that work with out the untrusted server cert error?
View 5 Replies View RelatedI have a client that needs to update a certificate on their 2125 controller. They have created a .pfx cert that does not work because of file type. I wanted to see what the best pratice would be for me to follow installing this cert and do I need any additional cert like a CA. I found a document but am not so sure that it is exactly what I need.
AIR-WLC2125-K9 : JMX1248K0EL
System Information
Manufacturer's Name.............................. Cisco Systems Inc.
Product Name..................................... Cisco Controller
Product Version.................................. 6.0.188.0
RTOS Version..................................... 6.0.188.0
[code]....
So since my web auth cert is expiring I got it renewed from VeriSign and they sent me back the file. Do I need to again combine the "myprivatekey.pem" file and the new one that I got and then load it on the WLC? Can't find any guidelines and instructions from Cisco on this. Or do I need to go through the whole regenration of CSR process again etc?
View 3 Replies View RelatedOur ACS (5.3) has self signed certificate, we have exported it and declared it in Certificate Authorities.We have exported it to have a Trusted Certificate for client machine.
This certificat has been installed on a laptop.The wlc is successfully setup for eap (peap & eap-fast has been tested > ok)I have this error in the log:
12514 EAP-TLS failed SSL/TLS handshake because of an unknown CA in the client certificates chain.I think the Access Policies (identity & authorization) are misconfigured: [code]
Am I able to use an SSL cert in the proxy list for the same VIP but on a different port?
View 1 Replies View RelatedI am running Cisco Adaptive Security Appliance Software Version 8.3(2) Device Manager Version 6.4(1). This will be used as a VPN gateway. I am having troubles installing our cert. I can install the cert, but it never connects witht he correct key. It references trustpoint0 when it is trustpoint1. I deleted all trustpoints and it still happens. That.vpngw4# sh run | begin rustcrypto ca trustpoint ASDM_TrustPoint0crl configurecrypto ca trustpoint ASDM_TrustPoint1keypair ASDM_TrustPoint0crl configurecrypto ca certificate chain ASDM_TrustPoint1certificate 0f8e62 308203d5.8c quitI deleted both trust points and when I do a sh run both are gone, but when I then import the cert (via ASDM) it creates trustpoint0 again.
View 3 Replies View RelatedUsing Sha1 for Cisco 7925g and sha256 for data. Two separate CA's, one EnTrust (SHA1) the other Local Wondows CA (SHA256); ISE can only use one at a time to process a particular protocol (ie..EAP-TLS, HTTP, etc...) As a result we have to have a separate PSN just for Wireless and Wired VoIP (which can only hold SHA1 RSA1024).
View 5 Replies View RelatedI have two Cisco WLC 5508 controllers that I'm trying to set-up for our new corporate WLAN. I've gone through most of the configuration fine but have ran into an issue uploading a signed certificate to one of my controllers. I should point out that I have managed to upload the certificate successfully to one of the controllers, I just can't seem to upload it to the second.The issue is as follows:
- I've logged into the controller, gone to Security -> Web Auth -> Certificate -> Download Certificate
- I've specified my tftp server details and selected apply
- the process begins and I can see through my tftp client that the controller is attempting to copy and install the certificate
- The controller tries to install the certificate but fails, reporting the same
I have a doubt about CiscoWorks. I need to generate the self-signed certificate with a key of 2048 bits to generate a CA with VeriSign. CiscoWorks do this automatically with a key of 1024 bits and I do not find a form to elect a a diferent key. Is it possible to generate a certificate with 2048 bits key?
Another problem is that I have CiscoWorks installed on Solaris. Many times at day the web application does not work and the only way to recuperate it is with the command "init 6" and I have to way 15 minutes until I can have access again. Why is produced this error? Who can I fit it?
I have just renewed the self signed certificate on a v5.2 ACS and expiry date of 2013 is showing in the ACS GUI. However, when I start an ACS Admin session and view the certificate information in the browser it is showing the old expiry date of 2010. I have tried this in IE and Firefox and the certificate information is the same.
Is there a way I can get the browser to pick the new certificate ?
We are currently evaluating ISE and I am stuck with the PEAP authentication (with Server side Cert).Our current setup consists of two 5508 controllers, 30+ access point. For authentication we are using PEAP with (server side Cert). We have an IAS server which is also acting as a CA server. We are using Cisco’s NAM as a supplicant on Windows XP & 7 workstations. I would like to use ISE for authentication. I would like to use PEAP with Server side Cert (similar setup like IAS). I want ISE to perform the same function in addition to profiling etc.....
I was able to integrate ISE with Active Directory but could not get it working with PEAP (server side Cert). I would also like to know if they used Microsoft’s CA server or Open SSL CA server or a third party CA server (Go Daddy, VeriSign etc.)Can you we ISE as a CA server just the way we used Microsoft’s IAS Server as a CA Server?
how to create new unique self-signed certificate on RV120W? I can create request for singning by external CA, but I cannot create new unique self-signed certificate itself.
View 2 Replies View RelatedRight now the Self-signed Certificate on my RV180W generates errors as it was issued to the MAC address instead of the current IP address. Need instructions on Generating a Self-Signed certificate (or 1 from my Windows Server 2012 Certification Authority) that will eliminate the constant barreage of certificate errors I get when trying to access the management interface of my device? the internal domain is mythos.local, netbios name of MYTHOS, and the device name in question is surtur.
View 2 Replies View RelatedThe establishment of IPSEC tunnel between the RV220 and QuickVPN client works properly with the security certificate of origin of the router.RV220 V1.0.3.5QuickVPN V1.4.2.1
Since the establishment of a security certificate self-signed, the RV220 and QuickVPN client refuses to work together .
Here are the log of the QuickVPN client
2011/09/27 12:45:14 [STATUS]OS Version: Windows 7
2011/09/27 12:45:14 [STATUS]Windows Firewall Domain Profile Settings: ON
2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
2011/09/27 12:45:14 [STATUS]Windows Firewall Private Profile Settings: ON
[code].....
I have ACS4 and i am planning to upgrade to ACS5.I would like to have such a rules:I have user1, one ASA device which is VPN concentrator for remote users.ASA have two different tunnel-groups: one which allow for logging via certificate (with mandatory pki authorization thru ACS) with disabled Xauth,and second tunnel-group with allow login thru typical Xauth with authorization thru ACS which users external database (RSA Tokens).So i have one user1 which can login thru VPN using RSA tokencode or certificate.For example: on phone user1 uses certificate, and on PC station the same user1 uses token password.For tunnel-group with pki authorization ASA checks username in ACS and in typical scenario login="CN from certificate" and password="CN from certificate". So we would need "two credentials" for the user - one for pki authorization, and second one external database (RSA token).Is such scenatio possible under ACS 5 ? where one user uses different credentials based on tunnel-group usage ?
View 2 Replies View RelatedYesterday I contacted live support with the problem that my network driver is crashing and giving me BSODs because of this when my download speed reaches above 5.5MBps.[url]...When I try to install those drivers, I first get a warning that the drivers aren't signed. I press "Continue" to dismiss the message but still at the end it fails to install and gives me the message "The drivers can not be loaded because they are not digitally signed", leaving you with a useless device.I bypassed the check windows is doing by turning off the check by running Windows in "Test Mode". I have test-signed the drivers myself that allowed me to install them. Now my device is working and not giving me BSODs anymore.
What I want is the drivers to be digitally signed by linksys/cisco. I think it's very unprofessional to distribute unsigned/useless drivers to customers. I am lucky that I am somewhat more experienced with this stuff, but what about people that are not? I think everybody should be able to install the latest drivers without any problems, without the need to hack into windows.I hope to see new drivers soon, or the same drivers but then digitally signed so I can turn off "Test Mode" again removing this ugly watermark in the bottom right corner.
he will lose connection with his chat programs for like 2 minutes then automatically be signed back on. He says he notices no other connection loss, but notices that sometimes his streaming will lag or games will lag. His ISP is Armstong (?) and he's wired to the router. XP OS.
View 3 Replies View RelatedI am support one client for, whom falls under Security scans mandatory for new implementation of ASA 5520 device. The client uses Nessus Scan and the test results are attached.The Nessus scanner hit on 1 Medium vulnerabilities.
View 2 Replies View Relatedi have configured vpn on asa 5505 and 881 router, as per below design,i am seeing the tunnel is built from cisco 881 router for few seconds and the its got delted. but nothing showing in asa.
View 1 Replies View RelatedI've been tasked with setting up an ASA 5505 on our ADSL modem & am very lost. I've put the PPPoE details into the ASA 5505 to authenticate with our ISP, but can't get out through it. I've looked at guides, videos, compared configs
This is the current config...
: Saved:ASA Version 8.2(5) !hostname asaenable password GuuH2OTIRWlZP8z3 encryptedpasswd 2KFQnbNIdI.2KYOU encryptednames!interface Ethernet0/0switchport access vlan 2!interface Ethernet0/1!interface
[Code]....
I am attempting to configure an ASA 5505 with SSL VPN. The users request is from anywhere, be able to web into the Cisco ASA. [URL]. At that point, we will require them to authenticate through Active Directory via ACS 5.2. The Cisco ASA 5505 is a 50 user ASA. We have also purchased the mobile license as well as a 10 user premium license. That was a bear in itself.
1. How do I configure the SSL setup to use a 3rd party certificate, such as a Comodo certificate?
2. How do I determine which version of AnyConnect I should use for this? We will support windows, macs, linux and smart phones as well as Tablets.
3. if you do a show version, you get all the capabilites of the ASA of which some are disabled or deactivated. Any chart that will show us, what needs to be purchased to activated each line entry on the ASA? Is there an all encompassing PAK?