Cisco Routers :: How To Use WAP4410N Repeater RV180W Wireless Network
Mar 22, 2013
How to use WAP4410N repeater Router Mode RV180W wireless network. until now it's still not working.
And the bottom line is I want keep RV180W in Router Mode,not WDS Bridge or WDS Repeater mode.
During the search I find that WAP4410N WDS Repeater is not compatible with RV180W,but I'm not sure about that, so how to configure it
My goal is use two WAP4410N expand RV180W Wifi Range that can cover the dead spot in my office.
View 1 Replies
ADVERTISEMENT
Dec 20, 2010
I am trying to setup an E3000 router and extending the network with a WAP4410N acting as a repeater.
I am faced with the same problem and it looks like it all comes down to this: without the WAP4410N having a physical connection to the LAN, it will not connect to the E3000 as a wireless client whether it's configured in AP mode: WDS Repeater or in client/repeater.
I've tested with various permutations that have been explored in the various discussions: matching channels/bandsmatching and non-matching SSIDs matching security settings using site survey to set the mac address of the E3000 (ensuring it's the MAC of the 2.4Ghz wireless)setting a static IP on the WAP4410Nensuring both devices are on the same subnet. Any way to be truly successful with this pair up of E3000 & WAP4410N or is it simply a technical product limitation?
View 1 Replies
View Related
Apr 18, 2012
Im having problems with setting up my cisco WAP4410N as a repeater to extend the signal of cisco E2500.It works fine when there is no password to be set on both devices. But when either one of these devices had beenset a password on it, then WAP4410N failed to extend the signal of E2500.
I tried steps as below:
1. Same password type in WAP4410N and E2500.
2. Different password type in WAP4410N and E2500.
3. Set password in WAP4410N ONLY.
4. Set password in E2500 ONLY.
All steps above makes WAP4410N fail to extend the signal range of E2500. WAP4410N successfully works as a repeater to extend the signal of E2500 when there is no password to be set on both devices.
View 2 Replies
View Related
Oct 14, 2012
I recently bought one RV180W and two WAP121 in order to make a wireless extension of a network.I configured RV180W as Router and the three of them have the same SSID and password.Also, I added in RV180W WDS configuration both MAC Addreses of WAP121's and in WAP121's WDS configuration the MAC Address of RV180W.Even I tried in WAP121's with and without encryption using the same WPA Key of the RV180W.
The thing is that is not working at all. They work great separately but right WAP121 can't stablish WDS link with RV180W neither do the left WAP121 with RV180W.I tested WDS configuration of WAP121's and they can see each other between them using standard WDS configuration, so I assume that WDS function of WAP121's works great.Finally I try the same config but setting RV180W in WDS Bridge and WDS Repeater without any different result.Do I have any chance to make the topology I showed up would work? How do I have to configure the RV180W and WAP121's?
View 1 Replies
View Related
Jul 20, 2010
I would like to ask for assistance on how to configure one unit WAP4410N access point to work as repeater to one unit WRT120N wireless router.
As a background, I had one WRT120N already in my house before I bought one WAP4410N as advised by a Linksys guy. I wanted to wirelessly extend the signal of my WRT120N wherever its signal is so low around my house. The WAP4410N should work as repeater to WRT120N.
I already configured WAP4410N to work as repeater by enabling all the choices in its wireless AP mode like the “wireless WDS repeater” and the “wireless client/repeater” but to no avail. I successfully setup a similar scenario before using the old pair of one WRT54G and one WAP54G. I replaced the old pair with the newer one ( WRT120N and one WAP4410N).
Is the tandem of WAP4410N and WRT120N can be configured technically as like as what I wanted? Do I need to upgrade the firmware of both devices? Did I miss something in the configuration?
View 2 Replies
View Related
Mar 9, 2011
We have a WAP4410N as a Access Point and a second WAP4410N as a Wireless WDS Repeater. The settings are as of below.
We couldn't get the mobile users to get connected to the Access Point. But if we uncheck the option "Allow wireless signal to be repeated by a repeater.", it works.
View 4 Replies
View Related
Dec 10, 2012
I would like to provide WiFi in a big house of 4 floors so I have installed 1 WAP4410N wired to the Internet router to act as access point and I have configured 3 others WAP4410N as WDS repeater of the first one.In the first one (the AP), I have checked the option "Allow Wireless Signal to be repeated by a repeater" then entered the 3 repeaters' MAC addresses as allowed devices to repeat the signal.
Is that configuration OK ? Is there any way to add another (a fourth) repeater to this configuration ? Because there is only 3 fields to specify allowed repeaters' MAC addresses in the AP.
View 2 Replies
View Related
Mar 7, 2011
I have a WRT160N and a WAP4410N but can not get WAP function as a repeater. I have already put as Wireless Client / Repeater and Wireless WDS Repeater. I notice they are both with the same settings security. View attach file.
View 14 Replies
View Related
Sep 4, 2012
configuration WAP4410n.I configure 1 wap4410n mode access point, is ok.I place 6 wap4410n in building as wireless repeater.I can not configure the right sequence.How do I set up 6 repeaters with access point ?
View 2 Replies
View Related
Apr 20, 2011
Currently I have a WAP4410N setup and would like to add a second WAP4410N but as wireless repeater. I want my users to have wireless access without the need to keep changing the wireless connection based on their location within the factory.
The AP Mode on teh WAP4410N gives me the options below, but I am not sure which one is the correct one:
Option 1 - Wireless WDS Repeater
Option 2 - Wireless Client/Repeater
Below is the link from cisco with explanation. [URL]
Also, if have WAP54G, can I setup this unit to be a wireless repeater with the WAP4410N devices? or all repeaters must be of the same model? Existing WAP4410 is setup to operate at Wireless B/G Mixed mode.
View 9 Replies
View Related
Apr 20, 2011
I need setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer’s site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be:I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values. So what am I missing?
View 1 Replies
View Related
Apr 6, 2011
i have WRT120N and WAP4410N, can i config WAP4410N to be repeater to repeat signal from WRT120N??if it can't, could you tell me what kind of wireless router that compatible with WAP4410N?
View 2 Replies
View Related
Apr 30, 2011
Setting up a WAP4410n v 2.0.1.0 as a repeater. Warning, this is the first time I have worked with a repeater. I have tested with a netgear router and a Linksys 160n router. Unfortunately I only have the netgear to continue testing with since the Linksys is at my customer's site. I can get my hands on a Linksys E3200 if I have to. I have tried a number of setting combinations and I still cannot get the signal to be repeated. So this is what I think the setup should be: I setup the router and the WAP4410n repeater to have the same ssid and channel. For security I first tried to have both the router and the repeater to use WPA2 personal using TKIP then I read that there is a problem using WPA2 with version 2 of the firmware so I then tried using WEP having both the router and repeater using the same key. I selected Wireless WDS repeater mode. I did a site survey and selected my router. Now from what I understand, which is very little, this is all I should really need to do. I have left all of the other settings to the default values.
View 2 Replies
View Related
Apr 26, 2011
i'm having WAG320N Linksys by Cisco , connected & working properly i need to connect 2 WAP4410 N to the router through wireless ( not wired )
i've did the same SSID same security same everything tried all the possible settings but it's not working as a repeater i've read the blogs & found that some people talking about new beta firmware i've tried to find it out to try but i didnt find it any where
View 1 Replies
View Related
Nov 14, 2010
I have a wap4410n acting as AP and a second wap4410n acting as wds repeater.
I've only managed to get the wds repeater to work when it has a different ssid to that of the ap - I'd like the wds repeater to have the same ssid as the ap, should things work in this configuration?
View 21 Replies
View Related
Apr 21, 2013
I got : RV180W router updated with the last firmware.Static IP for the DMZ host (Synology Server 212+) My problem is that I had try all combinaison since 10 days to get IP source in synology interface (to block IP's of bad connections...) but, I only see the RV180W adress....So impossible to block bad connections IP.
View 3 Replies
View Related
May 17, 2011
I just bought WAP4410N from about 3 days ago, I would like it to work as a wireless repeater to my 3com router model 3CRWDR100A-72. In the router setup page I enabled WDS, made a search for the wireless networks and I found the WAP signal and the router already got its MAC address. I went to AP mode in the WAP4410N, enabled the WDS repeater and made a site search for the router and got its SSID and MAC address.
Although all the above steps, everytime I connect any client to the WAP4410N I can not connect to the internet, all what I got is just the IP of the WAP and subnetmask without any default gateway nor DNS
In addition I tried to setup the WAP as wireless client epeater, but the same thing hapen, I can not connect to the internet through the WAP.
I am using WPA encryption on the router but I did not get any notification to enter the pass key during the setup of the WAP, which is strange for me!
Do I have to change my 3com router to linksys one as the 3com is not compatible with the WAP?
View 1 Replies
View Related
Sep 21, 2010
I also have problems with this type of accespoint, i have 2 (one in AP mode and the other in Client/Repeater mode).
Very often the connection between the pc and the repeater, and also between the 2 accespoints just "drops" out (like its resetting itself).
The accespoints are in enough range of eachother, so thats not the problem.
After the contact with Cisco here in Holland they said this type (4410N) is not stable with the 2.0.0.5 firmware, and its also limited to the B and G (not N) wireless, because else the accespoint will be even less stable??.
When can we expect a propper solution to this Cisco problem?
View 18 Replies
View Related
May 26, 2012
1) Apparently, my Cisco modem likes to assign new IP addresses to things, so I didn't figure out the web access page until an hour in (was NOT 192.168.1.245)
2) Do I input the same IP address, subnet, DNS and default gateway as my Cisco modem? It has a wireless router and switch bundled in, should I use the wireless network's MAC address or the wired?
Currently, it's set to 'automatically configure':
IPv4
Local IP Address: 192.xxx.x.xx
Subnet Mask: 255.xxx.xxx.x
Default Gateway: 192.xxx.x.x
Primary DNS: 64.xx.xxx.xxx
Secondary DNS: 0.0.0.0
I can access the page fine, but I cannot get the wireless client working...
3) I did a site survey and found my existing network and inputted its SSID and MAC address, but nothing happens. I still get one bar on my wireless devices indicating the AP isn't working.
View 1 Replies
View Related
Sep 21, 2010
I have just been escalated to Level 3 support about my bridging issues.Bridge / Repeater mode configuration separated by 150 feet. Worked perfect for over 3 months.Upgraded firmware due to lockups starting to happen, now cant get the bridge / repeater to work longer than 15 min.After MANY support calls, new devices sent (version 2's) still no luck.
Talked to Marcelo at1 866 606 1866 and he stated that the Bridge / Repeater mode will not be supported farther than 50 Feet.(seems like a cop out to me) He didn't seem to have an answer as to why it worked for 3 Months other than interference Of which I have ran spectrum analyzers and see no Interference. **** even 10 feet away I cant get the units to work longer than 15 min.So I definitely think the 50 foot thing is a BS answer.
Also they have told me that External Antennas are not supported with these devices.Again even though People 500 feet away connect just perfect (without a bridge / repeater mode) with 50% coverage!
so here I am (spent 600 bucks) on bricks.. and nobody will support the device and I cant seem to get my money back.I have 8 customers with these devices, I am not going to use Cisco any longer. However will continue to fight this,as we all seem to have the same BS issues.
View 1 Replies
View Related
Dec 21, 2010
Can a WAP4410N be used as a repeater on an existing WPA2 + EAP-TLS WLAN? The existing WLAN is on a Cisco 871W router; we hope to use a WAP4410N as a repeater to extend it.
I've not had much luck so far with the "repeater" and "WDS repeater" AP modes on the 4410. I'm either configuring it wrong, or perhaps the 871W needs a config tweak? Or perhaps the 871's wireless can't be repeated like this?
View 4 Replies
View Related
Dec 7, 2009
I have purchased 4 of these devices about 2 months ago and have experienced all of the issues reported within this thread. The came with the 2.0.0.5 FW rev installed, so unless the 2.0.0.5 on the cisco DL site is different, nothing I can do with that.I've tried making them work as stand alone AP's, Bridge<-> Bridge, etc... all modes seem to lock up eventually needing a reboot to get any functionality back.Ultimately, I need to make them work in AP<->Client-Repeater mode. I've not been successful in making them work in any mode for a prolonged period of time.
having just rfound this thread today, I have not tried hard coding the NIC's to 100/full, but will give it a try. If it works, great, but then that would defeat the purpose of buying an N radio AP. I would like the potential 300Mbps throughput.
View 13 Replies
View Related
Jun 15, 2011
Does Cisco WAP4410N work as repeater for Linksys E4200 ?i have Linksys E4200 and I need repeater for it.
View 2 Replies
View Related
Dec 15, 2012
I would like to ask if what is the difference between RV180W-E-K9-G5 and RV180W-A-K9-NA specifically the -E and the -A. As far as I know -A is the compliance code for Philippines. Am I right? If yes, what about -E? There is a documentation for wireless complaince on Aeronet devices but what about these SB products?
View 9 Replies
View Related
Jun 30, 2012
From the broadband modem/router connected with a Gigabit 8 port unmanaged switch. Then, one WAP4410N is connected to the switch, wired connection for a distance of 90 meters. WAP4410N is set as an access point to the area. Then the second WAP4410N will be run as a repeater to the first WAP4410N. My question is that, can we set the second WAP4410N as a repeater, without the need for it to be connected to the switch via ethernet cable.
View 7 Replies
View Related
Sep 15, 2010
I want to extend the range for a Linksys router WRT160N. I don't have the possibility to use an access point with a wired connection. I read on this forum that can be used WAP4410N configured as repeater, without wired connection. Can someone who has used this solution to confirm that it works? What configuration should be done on the router WRT160N to permit wireless signal to be repeated by WAP4410N?
View 5 Replies
View Related
Oct 12, 2011
I have AP1 setup with WPA2-Enterprise. How would I setup AP2 (WAP4410N) to be a repeater for AP1?
View 1 Replies
View Related
Jul 19, 2011
I bought my self a WRT120N as my wireless router for my house. and not a long ago i bought the WAP4410N, for my repeater (after i ask to some people).my house were concrete wall, it have about 15-20cm thick, and we try to avoid any wired LAN. The destinaton were unreachable with only WRT120N.it's look like this (what i want for the network on my home) : [code] i already tried to setting the WAP4410 as a wireless WDS repeater, and wireless client/repeater (with and without "Allow wireless stations to associate"). both were unable to connect (limited), although i get the signal. for the IP on the WAP4410N (192.168.0.50), i used static IP [IP, Subnet and Default Gateway were fill in] within the WRT120N range (192.168.0.2 ->192.168.0.51)
- how i configure my WAP4410N as a repeater?
- is there any settings that i must set on the WRT120N, before combining the WAP4410N?
View 1 Replies
View Related
Oct 7, 2012
I have an RV180W Wireless-N with firmware# 1.0.1.9 The problem is that any Macintosh computer will not work with the wireless network.The problem is consistent with several MacBook laptops, running Leopard, Snow Leopard and Mountain Lion.The MacBook connects with the wireless network and obtains an IP address.However when the MacBook tries to access a web page, it fails loads.Accessing LAN assets like network volumes and printers works fine.All mobile devices, such as iPhones, iPods and iPads work fine.I have tried numerous wireless settings on the router and the MacBooks and nothing works.The problem happens regardless of what kind of wireless security is present.There is not MAC filter.
View 1 Replies
View Related
Jan 18, 2013
This router keeps dropping all connections under a load of about 30 devices. everyone will lose internet access for a few minutes until it comes back. All settings are correct.This doesn't happen unless around 20-30 users are actively using their connections, both wired and wireless.
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] IP: 68.84.158.86
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] BCAST: 255.255.255.255
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] SUBNET: 255.255.254.0
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] GW: 68.84.158.1
Sat Jan 19 04:37:46 2013(GMT) [rv180w][System][PLATFORM] DNS1: 75.75.75.75
[code]....
View 1 Replies
View Related
Jun 5, 2012
I am trying to download firmware for an RV180W Wireless-N Multifunction VPN Firewall Router. I found updates for a 110 in BIN format (router only updates from IMG). Currently running stock firmware on that router and need the update.
View 2 Replies
View Related
Mar 6, 2013
We have the RV180W router and the WAP321 access point in our business. We want to broadcast two SSIDs from both locations: the office SSID, which shares routing to LAN traffic, and a guest SSID.The office computers are attached via ethernet to a switch off of LAN port 1 on the router. The AP is attached to LAN port 2 on the router.On the router, the office SSID and the LAN are members of VLAN 1. The guest network is a member of VLAN 2. From the router, everything works just fine.On the WAP, the staff SSID works fine, but the guest SSID has no internet. Both the office and guest networks get DHCP successfully from the router.Our VLAN membership table in the router and WAP are attached, as well as other configuration details.Why would we not be getting internet on the guest ID only on the WAP?
View 8 Replies
View Related
Jul 25, 2012
I recently purchase my first Cisco products for a network for our church. I have a RV180W router, WAP 121 Access Point and a SR2016T switch for our network, which is just pier-to-pier at this point. We have 5 computers connected with ether net through the switch and all see the Internet and work fine. The wireless connection through the router is working fine with our wireless devices (laptops and i Pads). Where I am having issues is with the AP. It is in different area away from the router being powered through POE instead of the regular power connection.
My problem is this: it takes FOREVER to connect to the AP and to the Internet, even when sitting directly under the AP with full signal. Once connected, it appears to allow Internet connection just fine, but getting to that point takes 15-20 minutes sometimes. Also, when I come back the next day, I have NO signal at all, as it seems the AP has "timed out" due to inactivity or something. I have to reboot the AP and the router to get it all back up and running again. I need for the signal to stay up all the time or at least come on when someone connects.
So, what am I doing wrong here? I have recognized and authorized the AP through the router config, security is set up fine and I can see it once it comes up. I have the AP set up as a completely different SSID, although I would prefer to have the AP as merely an extension of the router's wireless network if possible.
View 5 Replies
View Related
