Cisco Wireless :: Possible To Configure WDS C1131 AP Also As Infrastructure AP
Mar 16, 2013
I've setup the WDS and Infrastructure AP according to Document ID: 68098
1. The Infrastructure AP is registered and active in WDS AP.However, any client device such as NB or PDA cannot obtain IP address.In WDS AP the client device is shown as authenticating all the time. What I missed? Or there is somethig else need to be set?
2.Can I configure the WDS AP alslo as Infrastructure AP?I mean, to be WDS and Infrastructure at the same time, broadcasting the SSID etc.?
View 3 Replies
ADVERTISEMENT
May 9, 2012
I bought a CCNA lab for doing practice.The lab kit is made of some 2600XM routers.These routers have only one "fast ethernet port 0/0".I don't understand how I can configure these routers whith: Static Routing, Defoulte Route etc etc if I have only one "fast ethernet port 0/0" and I don't have the "0/1 port" too.
View 5 Replies
View Related
Jun 21, 2011
Suppose a broadcasted IP packet reaches one of the integrated RJ-45 ports on a 2911 ISR G2, will it be possible to configure the router so that the other integrated RJ-45 ports, ESM/EHWIC modules installed on the router, as well as the MGF also recieve the packet? Technically, the router should act similar to a switch with the SRE behaving similar to a seperate machine connected via the MGF and other external machine connected to the ports of the router to recieve the broadcasted packet.
Also, if SNMP traps were generated from the router,Will it be possible to send the traps from the router via the MGF to the SRE installed on the router?
View 1 Replies
View Related
Mar 13, 2011
We have several branch offices that only have a Cisco ASA 5505 connecting clients to the Internet, our main office and other networks. Some of the branch offices uses Site-to-Site VPN to connect to our main Office, other uses a VPN-service delivered by our ISP.
The networking is working fine, but we are having problems with figuring out how to handle dns lookups. I see that the ASA DNS Client can use conditional DNS forwarding, but it cannot act as a DNS server for our clients on the inside network.
We want to do the following:
- Default dns quires should use the DNS servers for the site's local ISP (some sites also uses dual ISP, so we are using DNS1 and DNS2)
- The domain name: company.local should use our main office DNS server (acces by Site-to-Site VPN or our ISP's VPN)
- The domain name: sitea.company.local should use our SiteA DNS server (acces by Site-to-Site VPN or our ISP's VPN)
etc...
We have solved the issue by using Windows DNS server's conditional forwarding for the branch offices that has a local Windows 2008 domain controller.
our branch office's that only have a Cisco ASA 5505 Security Applience?
View 3 Replies
View Related
Aug 31, 2006
I want to configure a MAC address on my asa 5520 interface.I ask you if exist a private MAC address range?
View 5 Replies
View Related
Feb 10, 2013
I need to configure on a cisco catalyst 6509 two VACL. On cisco 6509 there are already two SPAN ports configured, there are problems configuring other two VACL?
These VACLs send traffic to a Traffic Analyzer (SIEM), there are particular configurations to facilitate the operation?
View 1 Replies
View Related
Jan 29, 2013
I'm trying to do configuration archiving in Prime Infrastructure 1.2 with a 5508 WLC (7.4).The job always fails (Admin -> Background Jobs) with the following error (see attachement):"SNMP: Failed to establish SNMP connection xxxx - Cause: Device is Unreachable. Check the ReadOnly community string." I double checked the SNMP credentials, they do match. For testing I also added a Public community just for the PI. Same result.Am I missing something?Is this not intended for Wireless Controllers?
View 5 Replies
View Related
Apr 4, 2011
I would like to convert some 1142N LAP to Autonomous. Is there a way to do ?
I have noticed a new image : c1140-k9w7-tar.124-25d.JA.tar
I don't see a way to replace the image in flash ?
View 1 Replies
View Related
Feb 14, 2013
I'm deploying a Cisco Mesh infrastructure using WLC 7.2 version and 1552 APs.
This Mesh APs will be connected in the Light Pole and the RAP will be connected to the SP Switch located in this same Pole.
The MAP will be powered using Pole source power and will be connected to the RAP over 5.8 Bach haul.
My Customer asks if is possible that in case of SP Switch lost the connectivity to the Backbone IP, the RAP can connected to another RAP and maintain the connectivity to the Backbone over the Air, like REPEATER FALLBACK mode in Autonomous version.
For that I thinking to change the role of the RAP APs to "MAP with UTP Cable", but I'm not sure that a MAP AP with CAPWAP tunnel over UTP Cable can provide a Down link Backhand to another MAPs. That is possible?
View 3 Replies
View Related
Jan 12, 2013
I cannot integrate Virtual MSE 7.3.101 with my Prime Infrastructure 1.2 After I setup MSE via its wizard, I make a change on WCS username and password. When I try to integrate MSE with Prime Infrastructure, Prime notify me about the mismatch username/password.
Both systems are fresh install on my UCS C220 M3.
View 4 Replies
View Related
Jul 15, 2011
installed the E1000 router that AT&T provides with U-verse DSL. All works fine except that the device name that appears under "Network Infrastructure" in Windows 7 shows the original default name that Cisco assigned instead of the name I chose. It does not affect operation or performance but looks oddball. I don't see how it can be changed.
View 4 Replies
View Related
Sep 16, 2010
We have 2 aironet 1310 aps setup as infrastructure access points between 2 buildings. One went south on us & we placed it. Before the bad one went down, we were able to manage both remotely & could see them from the next device via CDP. Now, we can't connect or even ping either AP. And the weird part is that the switches that connected to each can see each other via CDP, but not the access points between them. I'm attaching the configuration. Before I make the 2.5 hour drive back to the site, what I may have misconfigured on either or both access points?
View 3 Replies
View Related
May 31, 2011
I have recently had to deploy a 1410 in a Root/Non-root bridge configuration to expand a terrestrial network across to an uncabled area.
All switches in play are 2960 series and the bridge is running with multiple Vlans.
Basic config as follows.
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname BRIDGE001!no logging consoleenable secret 5(code)
View 1 Replies
View Related
Mar 11, 2013
which version of prime infrastructure supports wlc5508 version 7.4
View 2 Replies
View Related
Jan 8, 2013
What is the difference between RPS 300 and RPS 675?
View 3 Replies
View Related
Jan 19, 2012
what is the use SPA and SIP...in router hardware ? What if we do not have them ?
View 1 Replies
View Related
Sep 25, 2012
I am managing a Cisco 881 with Adv Ip Services ( CISCO881-SEC-K9). It has IOS 15.0(1) M8 on it. I see that there is a new IOS version 15.2M&T that (I think is applicable), and I have read the upgrade procedures for upgrade via USB and TFT.
If I install it will my license for Adv Ip Services be preserved or overwritten. And if the latter, do I need to export it and reapply it? If so, what is the process?
View 3 Replies
View Related
Jul 31, 2006
I have an ME2400 running private V LANs. The primary V LAN is 20 and the secondary V LAN's are 21 and 22. Currently, management traffic is still on V LAN 1. My question is now that the ME2400 does not have anything plugged into v lan 1; the line protocol goes down, which means that I can no longer access the switch remotely. Is it possible to keep a SVI up up even though nothing is plugged into that V LAN? If so, how do I go about doing this?
View 2 Replies
View Related
Sep 25, 2012
My company purchased a PAK for ASA5505-SEC-PL a while back. I found it unopened and need to know if it can be used, without activating it on an ASA. I opened up a case with the Cisco TAC, provided them the PAK serial number and got the following responses from 2 different individuals:
1.Since the product was covered under warranty and then expired this means that the activation key was used before.
2. This PAK number is expired since (Warranty End Date 21-Feb-2009).
I responded that I am not interested in warranty information but I just want to know if the PAK can be used. Just because the warranty expired, does that REALLY mean the PAK can no longer be used? That doesnt make sense to me. Isn't there a tool on Cisco's website to put in the PAK S/N to see if it is available, has been used, and if so, when?
View 2 Replies
View Related
Mar 24, 2013
I need to use:
track 1 ip sla 1 reachability
In my 4507R core switch. Need to know which IOS should I use for this command as now I am using
cat4500-entservices-mz.122-46.SG.bin
In this when I am using
(config)#track 1 ip ?
route IP route
View 1 Replies
View Related
Mar 30, 2013
What is the difference between ASA-SM1 and FWSM and what is the throughput of it?
View 1 Replies
View Related
Feb 22, 2012
I need some fiber to run between a Cisco Nexus and an IBM server with Intel NIC. It's 30meters, and LC-LC connectors.What is the difference between 62.5/125 vs 50/125?
View 1 Replies
View Related
Nov 28, 2011
Is there any difference between these two models from hardware standpoint?
View 1 Replies
View Related
Jul 4, 2011
I am going to be updating the IOS on our Cisco ASA 5520 from verion 7.0(8) to 8.2(5). I am also going to setup AnyConnect. Are there any major changes in the 2 IOS versions that I need to be aware of or will the config work in either version? Also, we are currently using the Cisco VPN Client to connect to our network. Will that still work after the upgrade?
View 3 Replies
View Related
Jul 6, 2011
Is the configuration information for each of the access points that has joined a wireless lan controller stored somewhere specifically in the configuration screens? I enabled the power injector override on one of my access points which is plugged into a POE switch and of course now it will not stay up for more than a few seconds. Therefore I cant just go to the wireless list and modify the configuration there. I cannot seem to find it anywhere else to change it and bring it back up.
View 3 Replies
View Related
Apr 9, 2013
WCS 7.0 to Prime Infrastructure 1.2 migration?I am so confused on the migration procedure as I found the documents in Cisco kind of contradictory.Some document said it is required to upgrade WCS to NCS 1.1 before to go to prime infrastructure 1.2.And the other document said WCS can directly upgrade to prime infrastructure 1.2.
View 13 Replies
View Related
May 6, 2013
we installed a new CPI 1.3. Both machines are in the same subnet and close to each other. Everything looks fine and is installed as we see in the config guide.When we halt the VM of the primary Server, the backup takes over but with errors. I'm also not able to login! [code] my colleauges did the same a few days ago also with problems or similar problems and restore the server from backup.
View 2 Replies
View Related
Feb 20, 2013
I´m about to upgrade a customers appliance box to PI 1.3. I am guessing an upgrade to 1.2 would be almost the same, license wise.
View 10 Replies
View Related
Mar 24, 2013
I have WS-3750G-12S-E with me and would like to configure BGP on the same. whether it is advisable to configure BGP on 3750G or not.
View 10 Replies
View Related
Jun 13, 2011
I purchased a Cisco 2621 with IOS Version 12.3(26) on it. When I went through the commands, I couldn't find any VLAN or VTP available. I need to make sure I can see this on the device in order for me be able configure VLAN on my network and get ready for my CCNA exam.
Below is the version on the device and I also attached the available commands:
Version: IOS (tm) C2600 Software (C2600-I-M), Version 12.3(26), RELEASE SOFTWARE (fc2)
View 4 Replies
View Related
Oct 10, 2011
I have a 7606 running c7600rsp72043-advipservicesk9-mz.122-33.SRD2.bin with SIP-400 card that has suddenly stopped working, on checking the logs i see the following:
%ONLINE-SP-6-TIMER: Module 3, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 3 set off (Module Failed SCP dnld)
I have tried reseating and even moving it to a different slot but no luck.
%ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 4 set off (Module Failed SCP dnld)
sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 20 ESM20G 7600-ES20-GE3C JAE1237UT90
2 4 7600 ES+ 7600-ES+4TG3CXL JAE13157HIW
3 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE13219CZH
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE JAE1151819I
6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE JAE11495POH
[code].....
View 4 Replies
View Related
Jun 6, 2012
Are the IOS commands the same on a router and a ASA for these two topics....CBT Nuggets where I train has 553 videos for some of the new topics. I am preparing for 554 as it has more ASA focus and thats more interesting to me.
View 1 Replies
View Related
Jan 10, 2013
I have recently had to rebuild the cookie information for a cisco 877 series router due to it being erased by an electrical surge.
I've successfully got it running again by copying the cookies from an identical router (obviously changing the serial numbers and so forth so it passes its verification checks).
The last piece of information I need is the Chassis MAC Address. I don't want to use the one from another router since there will probably be conflicts.
I tried following this Field Note, even though it isn't specifically for my model and it didn't work.
[URL]
how I can get the mac address from the system somehow?
View 2 Replies
View Related
