Cisco Infrastructure :: ME 2400 - How To Keep SVI Up
Jul 31, 2006
I have an ME2400 running private V LANs. The primary V LAN is 20 and the secondary V LAN's are 21 and 22. Currently, management traffic is still on V LAN 1. My question is now that the ME2400 does not have anything plugged into v lan 1; the line protocol goes down, which means that I can no longer access the switch remotely. Is it possible to keep a SVI up up even though nothing is plugged into that V LAN? If so, how do I go about doing this?
View 2 Replies
ADVERTISEMENT
Aug 16, 2011
I am building the VPN with Sonicwall and Cisco Router, the VPN status is indicated ok on the Sonicwall and able to ping only,I know it required ACL on Cisco but it failed, I cannot ping the sonicwall from cisco, the access from external to cisco internal is also fail.
Site A SonicWall = 192.168.1.0Site B (Cisco) = 192.168.143.0
crypto isakmp policy 15encr 3desauthentication pre-sharegroup 2lifetime 28800crypto isakmp key XXXXX address 118.142.###.###crypto ipsec security-association lifetime seconds 28800crypto ipsec transform-set T1 esp-3des esp-sha-hmaccrypto map tosonicwall2 15 ipsec-isakmpset peer 118.142.116.146set transform-set T1match address 110 ip nat inside source route-map nonat interface Dialer0 overloadip nat inside source static tcp 192.168.143.20 80 202.64.135.### 80 extendableip nat inside source static tcp 192.168.143.20 3389 202.64.135.### 3389 extendable!access-list 1 permit 192.168.143.0 0.0.0.255access-list 110 permit ip 192.168.143.0 0.0.0.255 192.168.1.0 0.0.0.255access-list 110 deny ip 192.168.143.0 0.0.0.255 anyaccess-list 115 permit ip 192.168.143.0 0.0.0.255 anyaccess-list 115 deny ip 192.168.143.0 0.0.0.255 192.168.1.0 0.0.0.255no cdp run!route-map nonat permit 10match ip address 115!
View 7 Replies
View Related
Feb 20, 2013
the 2400 and Wifi though I was unable to find anything specific enough for my scenario.I'm trying to connect my Dell 2400 Desktop to wireless internet using a Wifi USB...It is able to connect to the Router, but unable to connect to the internet. I've gone and downloaded the suggested drivers for the desktop, though still having the same issue. In the bottom right corner of the taskbar it will show a strong connection to the router, though I have a LAN connection that says " Local Area Connection: A Network Cable Is Unplugged" and it lists the connection through Broadcom. Here is the relevant information I have (judging from what previous posts have looked for).First Up, the Wifi USB I'm using is a NetGear WNDA3100V2 GenieI've gone an done the ipconfig, and tried pinging sites, though the pings timed out and returned nothing. The results of the ipconfig are:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Mike
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
[Code].....
View 1 Replies
View Related
Aug 21, 2012
Before I put in place any network security appliance POC, my wireless network worked fine.Note: ethernet works fine all the time and confirm my internet is okay too. Just wireless.
First time, I got Palo Alto vendor to setup POC. It screwed up my wireless. We removed on 1st day itself and re-configured everything all over again.Now before holiday break, Sonicwall vendor setup POC for us. It worked fine though for 1 week and now the wireless gone crazy again.
3 bars, 2 bars, 5 bars, sometimes no bar.Then when there's POC, my guest wireless network will dead too.
I can't figure out the problem and what's causing such instability?If I understand correctly, this is how my network works:-
sonicwall nsa 2400 (router 192.168.1.1)
cisco linksys wireless (before sonicwall, we used this as router. Now used as wireless access point).
tp-link 48-Port 10/100Mbps + 4-Port Gigabit Web Smart Switch
is there anything in particular I should take note about? or any tools to analyze my wireless network problems?
View 3 Replies
View Related
Jun 8, 2012
My company has a Cisco IAD 2400 which is handling our phones and the internet (from Service Provider). We are adding a second router, a Cisco 1921, to our network,I think I have everything set up correctly. One department is using the 192.168.2.0/27 subnet. I can ping each computer within that subnet. Also, within this subnet, I can ping the router interface at 192.168.2.1. I can ping 192.168.1.2 successfully as well. This is the interface on the 1921 that goes to the 2400. However, if I try to ping 192.168.1.1 (interface on 2400), I get "Reply From 192.168.1.236: Destination Host Unreachable" I get the same thing if I ping 8.8.8.8.Within the 1921, I can ping 192.168.1.1 and 74.125.224.72 (random google ip) successfully.
View 1 Replies
View Related
Oct 5, 2008
I am trying normal password recovery for (cisco routers) for IAD 2400 but iam unable to get in rommon mode ?
View 3 Replies
View Related
Apr 26, 2009
I am using a Negear Wireless USB adapter for the Dell Dimension 2400. The computer can see the wireless adapter in Device Manager; but it does not pick up any wireless signals.
There is a wireless switch to turn on/off for the laptop, but a desktop does not have such feature.
View 4 Replies
View Related
Feb 6, 2012
I have a Dimension 2400 PC and a am about to get awireless router with anew provider. I cannot find a wireless switch so does any one know and if if I can connect?
View 2 Replies
View Related
Feb 5, 2013
I am trying to find a tool that will monitor the web traffic for one specific user. If it is capable of bundling it into a report that would also be a benefit. I have searched, but not come up with much aside from broad network monitoring tools. All that is really needed is to capture all the activity from http traffic for this one specific user/PC (since she uses the same PC all the time). We have a Sonicwall NSA 2400 as our internet filter, but I was not able to locate anything on there for specific user reporting.
View 2 Replies
View Related
May 1, 2005
She has a Dell Dimension 2400, Service Tag 2VG3341 running Win XP Home with Service Pack 2.
At startup we get a message from Norton A/Virus 2003 - Symantec cannot scan your email address, because your network is not properly configured.
Canceling this message and trying to connect to the internet using the Dial –up connection gives this message:
Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this connection.
I have checked the Network Properties as per Windows Troubleshooter, but cannot find anything unusual.
I have also ran the Dell Diagnostic CD, but these tests have are all clear.
The Windows firewall is also disabled
When I try to enable it I get the error message –
Windows Firewall settings cannot be displayed because the associated service is not running. Do you want to start the Windows Firewall Internet Connection Sharing (ICS) service?
After clicking on “Yes” A dialog box shows “Starting the Windows ICS” Then comes the message “Windows cannot start the Windows Firewall /ICS Services”
View 1 Replies
View Related
Aug 2, 2012
I just got my dell dimension 2400 up n running again.
1) I need a new operating system . i know how to do that what with windows being designed to make computers work properly or what is the latest thats not vista or could i just get a copy from a friend? <--- that may not be particularly legal but idc i just want to know if it would work if a new disk is too expensive
2) I need internet connectability i have a working att wireless router brand new just got delivered today and i have a d link wireless reciever thing i just got from my buddy but how to get the internet up n running without boring holes in the floor / wall or dragging a cable 18 miles from the router to the computer so i need it to be wireless
3) I am not sure what to do with it do i just need soft ware updates or do i need hardware updates to get it up to speed with the so called "big boys even though its far larger than any laptop my goal is to have a fast running internet capable game capable and multitasking computer with which i can do.
View 1 Replies
View Related
Jan 8, 2013
What is the difference between RPS 300 and RPS 675?
View 3 Replies
View Related
Jan 19, 2012
what is the use SPA and SIP...in router hardware ? What if we do not have them ?
View 1 Replies
View Related
Sep 25, 2012
I am managing a Cisco 881 with Adv Ip Services ( CISCO881-SEC-K9). It has IOS 15.0(1) M8 on it. I see that there is a new IOS version 15.2M&T that (I think is applicable), and I have read the upgrade procedures for upgrade via USB and TFT.
If I install it will my license for Adv Ip Services be preserved or overwritten. And if the latter, do I need to export it and reapply it? If so, what is the process?
View 3 Replies
View Related
Sep 25, 2012
My company purchased a PAK for ASA5505-SEC-PL a while back. I found it unopened and need to know if it can be used, without activating it on an ASA. I opened up a case with the Cisco TAC, provided them the PAK serial number and got the following responses from 2 different individuals:
1.Since the product was covered under warranty and then expired this means that the activation key was used before.
2. This PAK number is expired since (Warranty End Date 21-Feb-2009).
I responded that I am not interested in warranty information but I just want to know if the PAK can be used. Just because the warranty expired, does that REALLY mean the PAK can no longer be used? That doesnt make sense to me. Isn't there a tool on Cisco's website to put in the PAK S/N to see if it is available, has been used, and if so, when?
View 2 Replies
View Related
Mar 24, 2013
I need to use:
track 1 ip sla 1 reachability
In my 4507R core switch. Need to know which IOS should I use for this command as now I am using
cat4500-entservices-mz.122-46.SG.bin
In this when I am using
(config)#track 1 ip ?
route IP route
View 1 Replies
View Related
Mar 30, 2013
What is the difference between ASA-SM1 and FWSM and what is the throughput of it?
View 1 Replies
View Related
Feb 22, 2012
I need some fiber to run between a Cisco Nexus and an IBM server with Intel NIC. It's 30meters, and LC-LC connectors.What is the difference between 62.5/125 vs 50/125?
View 1 Replies
View Related
Nov 28, 2011
Is there any difference between these two models from hardware standpoint?
View 1 Replies
View Related
Jul 4, 2011
I am going to be updating the IOS on our Cisco ASA 5520 from verion 7.0(8) to 8.2(5). I am also going to setup AnyConnect. Are there any major changes in the 2 IOS versions that I need to be aware of or will the config work in either version? Also, we are currently using the Cisco VPN Client to connect to our network. Will that still work after the upgrade?
View 3 Replies
View Related
Jul 6, 2011
Is the configuration information for each of the access points that has joined a wireless lan controller stored somewhere specifically in the configuration screens? I enabled the power injector override on one of my access points which is plugged into a POE switch and of course now it will not stay up for more than a few seconds. Therefore I cant just go to the wireless list and modify the configuration there. I cannot seem to find it anywhere else to change it and bring it back up.
View 3 Replies
View Related
Apr 9, 2013
WCS 7.0 to Prime Infrastructure 1.2 migration?I am so confused on the migration procedure as I found the documents in Cisco kind of contradictory.Some document said it is required to upgrade WCS to NCS 1.1 before to go to prime infrastructure 1.2.And the other document said WCS can directly upgrade to prime infrastructure 1.2.
View 13 Replies
View Related
May 6, 2013
we installed a new CPI 1.3. Both machines are in the same subnet and close to each other. Everything looks fine and is installed as we see in the config guide.When we halt the VM of the primary Server, the backup takes over but with errors. I'm also not able to login! [code] my colleauges did the same a few days ago also with problems or similar problems and restore the server from backup.
View 2 Replies
View Related
Feb 20, 2013
I´m about to upgrade a customers appliance box to PI 1.3. I am guessing an upgrade to 1.2 would be almost the same, license wise.
View 10 Replies
View Related
Mar 24, 2013
I have WS-3750G-12S-E with me and would like to configure BGP on the same. whether it is advisable to configure BGP on 3750G or not.
View 10 Replies
View Related
Jun 13, 2011
I purchased a Cisco 2621 with IOS Version 12.3(26) on it. When I went through the commands, I couldn't find any VLAN or VTP available. I need to make sure I can see this on the device in order for me be able configure VLAN on my network and get ready for my CCNA exam.
Below is the version on the device and I also attached the available commands:
Version: IOS (tm) C2600 Software (C2600-I-M), Version 12.3(26), RELEASE SOFTWARE (fc2)
View 4 Replies
View Related
Oct 10, 2011
I have a 7606 running c7600rsp72043-advipservicesk9-mz.122-33.SRD2.bin with SIP-400 card that has suddenly stopped working, on checking the logs i see the following:
%ONLINE-SP-6-TIMER: Module 3, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 3 set off (Module Failed SCP dnld)
I have tried reseating and even moving it to a different slot but no luck.
%ONLINE-SP-6-TIMER: Module 4, Proc. 0. Failed to bring online because of timer event
%C7600_PWR-SP-4-DISABLED: power to module in slot 4 set off (Module Failed SCP dnld)
sh module
Mod Ports Card Type Model Serial No.
--- ----- -------------------------------------- ------------------ -----------
1 20 ESM20G 7600-ES20-GE3C JAE1237UT90
2 4 7600 ES+ 7600-ES+4TG3CXL JAE13157HIW
3 0 4-subslot SPA Interface Processor-400 7600-SIP-400 JAE13219CZH
5 2 Route Switch Processor 720 (Active) RSP720-3C-GE JAE1151819I
6 2 Route Switch Processor 720 (Hot) RSP720-3C-GE JAE11495POH
[code].....
View 4 Replies
View Related
Jun 6, 2012
Are the IOS commands the same on a router and a ASA for these two topics....CBT Nuggets where I train has 553 videos for some of the new topics. I am preparing for 554 as it has more ASA focus and thats more interesting to me.
View 1 Replies
View Related
Jan 10, 2013
I have recently had to rebuild the cookie information for a cisco 877 series router due to it being erased by an electrical surge.
I've successfully got it running again by copying the cookies from an identical router (obviously changing the serial numbers and so forth so it passes its verification checks).
The last piece of information I need is the Chassis MAC Address. I don't want to use the one from another router since there will probably be conflicts.
I tried following this Field Note, even though it isn't specifically for my model and it didn't work.
[URL]
how I can get the mac address from the system somehow?
View 2 Replies
View Related
Sep 12, 2012
Just downloaded the Eval copy of Cisco Prime 1.2.
Wondering if I can run this under a VMware Player instead of loading it on a UCS server?
If yes, is there a recommended version of player?
View 1 Replies
View Related
Jun 3, 2012
We have been deploying ASA 5500 series devices for longer than I've been around. We have always used a script from a tftp server that would use the "wr net" command to send the running-config to the tftp server for daily backups. The script was setup to automatically name these "hostname-mm/dd/yyyy" for each device. We cannot seem to get this working on devices running ASA 8.43. In fact I can't even get the "wr net" command to work from the ASA at all even though I have the tftp server defined correctly (note this is going over the "outside" interface so I always get the warning regarding using the interface with the lowest security level). I'm sure there is something out there that I have overlooked, however I have not been able to come across this. Have there been any changes in the setup, or functionality of the wr net command or the tftp configuration with ASA 8.43?
View 1 Replies
View Related
Dec 20, 2011
We want to get MIB files for snmp v2 from Cisco 2851 Router running with IOS below,
c2800nm-advsecurityk9-mz.124-15.T7.bin
View 1 Replies
View Related
Feb 12, 2013
I have NCS 1.0 with 100 devices support license installed. Now knowing it has reached end of sale, and also for the fact that Prime does cover devices like routers, i went ahead to the upgrade path via PUT (Product Upgrade Tool). Finally I received an email (OBA) advising my order is ready. This email included two items in the shipment,
L-N-PI12-100-M=
NCS 1.0 to Prime Infrastructure 1.2 Minor Upg 100 Device
L-PILMS42-100-M
Prime Infrastructure LMS 4.2 - 100 Device Upgrade Lic
When i click to the link in the same email to download the license, it only shows me one file which is L-PILMS42-100-M I tried using this file and installing on the NCS1.0 but it gives me error that this file is not a license file. The license name suggests me that it is not the license to be installed on the NCS. The file should be L-N-PI12-100-M=
View 5 Replies
View Related
