Cisco Switching/Routing :: 2400 - Unable To Get Into ROMmon Mode
Oct 5, 2008I am trying normal password recovery for (cisco routers) for IAD 2400 but iam unable to get in rommon mode ?
View 3 Replies
ADVERTISEMENT
Cisco Switching/Routing :: Cannot Get Out Of Rommon Mode 1760
Dec 10, 2011I'm currently pursuing to take my CCNA and am currently studying for it, but have recently encountered a problem with one of my 1760 routers that I can not solve.Yesterday I went to boot up my router like normal, however when I went into hyperterminal I noticed the router was in Rommon mode. Thinking I could change the configuration registry, I tried to bypass the NVRAM by using confreg 0x2142. However this still causes the router to go into Rommon mode. I am getting an error that states that there is insufficient memory to load the IOS image. [code]
I have used the dir flash: command and can see the IOS image, and try to boot from it (boot flash:iosimagename) but it will still go back into rommon mode. I also just swapped the RAM from my other 1760 into this 1760 and it booted up and went into normal configuraiton mode without any issues. However, the other router now will not load it's IOS image and I get the exact same error.I'm at a loss here, and have searched to figure out where or how I can just wipe the router clean to try and start fresh, but cannot get out or Rommon mode. The only thing I can think of is that the RAM went bad since it wont boot up either machine.
Cisco Switching/Routing :: 6509 Stuck In ROMmon Mode?
Dec 16, 2012I have 6509 E. Actually what happen it last 3-4 times it reload its self and got stuck in rommon mode, i tried to boot it with boot by connecting a console cable on supervisor 720 2b. What and where is problem and why is stuck in rommon after reload.
View 11 Replies View RelatedCisco Switching/Routing :: Catalyst 4506e - Booting In ROMmon Mode?
Dec 12, 2012I have a Catalyst 4506e that works fine but if reload, it boots in rommon mode. I can start it with a boot command, but by default, i must type a command. My config-register is 0x2102.
View 5 Replies View RelatedCisco Switching/Routing :: 3550 - Copy IOS To Switch In ROMmon Mode?
Jan 24, 2012I have a 3550 switch that was replaced at a remote site with no IOS. This is a switch not a router so tftpdnld does not work.
[Code]...
The problem is the switches interface never comes up so try to connect to the tftp server. I read on google it can't be done on a switch to copy from tftp to flash in rommon mode on a switch and to use XMODEM. My problem is I do not have access to it, I ssh into a 3640 which is an access server for all devices and that is how I have console to it, how to use XMODEM over ssh.
But I'm fairly certain that there has to be a way to just copy it from tftp? I have a 3550 local and when I put it in rommon mode it stops the port check at port, port 1 goes from green when you plug it in to off then port 2 changes to amber and the rest green. So just by the look of this I would believe tftp would work; you just need to use port 1.
Cisco Switching/Routing :: Switch 6509 In ROMmon Mode After Power Outage?
Nov 28, 2012We have a cisco catalyst 6509 with Supervisor Engine . After power outage, the switch always start in Rommon mode. Configuration register is 0X2102, we want to it always start in normal mode. What should i do?
View 3 Replies View RelatedCisco Switching/Routing :: C2960 USB Flash Device Works In ROMmon But Not In Normal Mode?
Aug 7, 2012I have a 512MB USB Flash device and was able to boot the IOS on the C2960 from it.After that i tried to Copy the IOS file from the USB to the system flash, but it could not find the USB Device.At plugging in the device the systems tells me: "Transfer type 2 not supported" I configured the USB device in NTFS and FAT both are able to boot with the ROMMON, but the normal system does not accept them and i know i can do the copy over a TFTP from my laptop, but it is strange that rommon accepts the usb device and the system does not?
View 1 Replies View RelatedCisco Switching/Routing :: 4507R+E - Access ROMmon Mode Of Crushed SUP When Switch Running Through Second One
Oct 21, 2012I have one cisco 4507R+E.My question is if the IOS of the acive SUP crushed and the switch is running through it's second SUP then how to restore the IOS of the first SUP.Also how to access the ROMON mode of the crushed SUP when switch is running through second SUP.
View 1 Replies View RelatedCisco Switching/Routing :: 6503 Sup-2T Unable To Get Into ROMmon
Apr 11, 2013I have an issue with a customers 6503 with Sup-2T cards, where we are locked out of the console due to an authentication configuration error. So tried several times to get the card into rommon, with no success.
Checking through the various documents on CCO I dont find any reference to rommon on this card, but do find information on using the CMP to support the supervisor. I logged into the CMP but couldn't find a way from there to do a password reccovery either.So, is the `normal' IOS rommon/password recovery method supported.
Cisco Switching/Routing :: Destination Host Unreachable 2400
Jun 8, 2012My company has a Cisco IAD 2400 which is handling our phones and the internet (from Service Provider). We are adding a second router, a Cisco 1921, to our network,I think I have everything set up correctly. One department is using the 192.168.2.0/27 subnet. I can ping each computer within that subnet. Also, within this subnet, I can ping the router interface at 192.168.2.1. I can ping 192.168.1.2 successfully as well. This is the interface on the 1921 that goes to the 2400. However, if I try to ping 192.168.1.1 (interface on 2400), I get "Reply From 192.168.1.236: Destination Host Unreachable" I get the same thing if I ping 8.8.8.8.Within the 1921, I can ping 192.168.1.1 and 74.125.224.72 (random google ip) successfully.
View 1 Replies View RelatedCisco Switching/Routing :: C2950-24 / Unable To Take Control In Console Mode
Jan 25, 2012I use a C2950-24 switch, with IOS 12.1(22)EA12 release.When I try to connect in console mode, I can see the "Press RETURN to get started!" message, but it's not possible to me to have the # prompt.An "authorization failed" message is displayed. And the same message is prompted.
I try to recover password by following the recovery procedure. After the boot command, I never see the message "Continue with the configuration dialog? [yes/no]: ".
Cisco Switching/Routing :: 2691 - Unable To Reach Enable Mode By Console Connection
May 10, 2012I have 2691 router with following config
line console 0
login local
password xty
When i remove the login local from the line console i connect to console port and press enter it shows router prompt 2691Router> but i am unable to go to enable mode.If i telnet to router then i put username and pw then it goes straight to enable mode.
vty config is
line vty 0 4
exec-timeout 600 0
logging synchronous
login local
length 500
transport input telnet ssh
escape-character 3
Any reasons why i can not go to enable mode by console?
Dell :: Dimension 2400 - Error 720 - Unable To Connect To Internet
May 1, 2005She has a Dell Dimension 2400, Service Tag 2VG3341 running Win XP Home with Service Pack 2.
At startup we get a message from Norton A/Virus 2003 - Symantec cannot scan your email address, because your network is not properly configured.
Canceling this message and trying to connect to the internet using the Dial –up connection gives this message:
Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this connection.
I have checked the Network Properties as per Windows Troubleshooter, but cannot find anything unusual.
I have also ran the Dell Diagnostic CD, but these tests have are all clear.
The Windows firewall is also disabled
When I try to enable it I get the error message –
Windows Firewall settings cannot be displayed because the associated service is not running. Do you want to start the Windows Firewall Internet Connection Sharing (ICS) service?
After clicking on “Yes” A dialog box shows “Starting the Windows ICS” Then comes the message “Windows cannot start the Windows Firewall /ICS Services”
Cisco :: Ap1231g-e-k9 - Load New Bin Ios In Rommon Mode?
Jun 9, 2011loading a new bin file onto a Cisco wirless access point ,the access point i have found is only in rommon stage
Access point model is : ap1231g-e-k9.
Cisco WAN :: 1841 - How To Do Configuration In ROMmon Mode
Mar 19, 2011On new 1841 Testing Router, I deleted the flash & did the reload. After reloading, instantly I entered into the Rommon mode. I have a backup of the flash in my TFTP Server, which is connected to the 1841 Router. how can I restore my flash file into my 1841 Router. I can not get myself out of Rommon mode. I also now even can not ping the TFTP Server as well. Do I have to configure in the Rommon mode ?
how to restore the flash image via TFTP Server on my 1841 Router.
Cisco WAN :: 2600 - Cannot Enter ROMmon Mode Or Key?
Apr 4, 2012I upgrade to a Flash 32mbs memory stick, as I reboot the 2600 Cisco router, it appear in the ROMMON mode, nonetheless, I followed some wrong procedure by changing components on the ROMMON command line. however now the router reboot or start with symbol only V2V2v2a, and I can no longer enter the ROMMON Mode or key anything in. I have a copy of the IOS on my TFTP server.
[Code]....
Cisco Switching/Routing :: Cat 6506 Goes Into ROMmon
Nov 29, 2012I have a Cat6506. There were 2 Sup 720 in it for redundancy. They told me they had problems with this thing in the past needing to go out and reboot the machine. I need to go out periodically because it goes into ROMMON. I type boot and it comes back up. One time though neither one would reboot. I had to take a third one out there and reconfigure it. Now it is starting to do the same thing. One thing I did notice is they never connected it to an UPS. It is plugged strait into the wall with power going to two outlets. I am beginning to think there are spikes in the power occurring and this is sending it into ROMMON.
View 6 Replies View RelatedCisco Switching/Routing :: 3560E - Can't Get Into ROMmon
Sep 2, 2010I upgraded four 3560E, 12.2(44) to 12.2(55)SEThree 3560 works fine, the last one stops after 17-18 seconds with a solid green LED. I cant get into ROMmon, the switch doesn't boot up. its like "dead but still alive"
My TS:
1: Removed all SFPs.
2: Reset PSU and fan modules.
3: Replace PSU and fan modules.
4: Try to get into ROMmon.(pushing mode button and break seq.)
Startup LED:0-1 seconds: SYST: Amber RPS: Amber STAT: Green DUPLEX: Green SPEED: Green
1-17 seconds SYST: Blinking Green RPS: OFF STAT: OFF DUPLEX: OFF SPEED: OFF
18 s--> (only testet up to one hour) SYST: Solid Green RPS: OFF STAT: OFF DUPLEX: OFF SPEED: OFF
A working 3560EStartup LED information. If I compare a working switch with the faulty switch I can see about 18 seconds into bootingSYST change very fast from green to amber and continues with booting,this doesnt happened on the faulty switch (solid green 18 seconds). Pushing MODE button, doesn't get me in to ROMmon, this works for all the other switches.On a normal 3560 it takes around 40 seconds before I get in to ROMmon. With this faulty switch it stops after 18 seconds(solid green) and it doesnt respond.
Cisco Switching/Routing :: 4507 Went Into ROMmon
Jun 4, 2012Could not find a valid file in BOOT environment variable. BOOT variable can be set from IOS. To find currently setRom Monitor variables, type 'set' command.
Choosing a boot method, type 'confreg' command.rommon 1
>setPS1=rommon ! >RommonVer=15.0(1r)SG5SupportedFeatures=1ConsecPostPassedCnt=2DiagMonitorAction=NormalCONFIG_FILE=bootflash:cat4500e-
[Code].....
Cisco Firewall :: ASA5505 Stuck In ROMmon Mode?
Sep 22, 2010I've ended up in rommon mode on my new"old" RMA'ed ASA5505, and I'm stuck there, I'v tried to erase Disk0 and all that, and tftp'ed a new image into the box, but when booting I get the message :
INFO: Unable to read firewall mode from flash
WARNING: Unable to write firewall mode to flash, this is normal if flash is not formatted
Running Activation Key: 0x00000000 0x00000000 0x00000000 0x00000000 0x00000000
This activattion key is invalid, use default settings only
i2c_write_byte_w_suspend() error, slot = 0x0, device = 0x40, address = 26 byte count =1. Reason: I2C_UNPOPULATED_ERROR
Cisco WAN :: Management Port In ROMmon Mode - ASR1002
Jun 4, 2013Is it possible to use the mgmt port when in rommon mode? I use the Mgmt port when IOS is loaded and it works fine. I reboot the router, issue a break to put it in rommon and have set some variables but my Mgmt port never has link and I cannot ping it from the network. In rommon mode it looks like this:
PS1=rommon ! >
MCP_STARTUP_TRACEFLAGS=00000000:00000000
BOOT=bootflash:asr1000rp1-adventerprisek9.03.07.03.S.152-4.S3.bin,1;
IP_ADDRESS=10.71.50.101
IP_SUBNET_MASK=255.255.255.0
DEFAULT_GATEWAY=10.71.50.3
BSI=0
RANDOM_NUM=1133006948
RET_2_RTS=13:38:27 EDT Wed Jun 5 2013
RET_2_RCALTS=1370453907
?=0
Cisco Firewall :: Recover ASA 5505 IOS In ROMmon Mode
Feb 23, 2012i try to recover cisco ASA 5505 IOS in Rommon mode but i have this message : [code]
View 1 Replies View RelatedCisco WAN :: 1841 - Router Automatically Goes To ROMmon Mode
Feb 9, 2012I have one problem in my Client end router cisco 1841.
Everyday we switch on the router it will automatically goes to ROMMON mode.
So i take remotly and check wheather the IOS is corrupted or not.
So i use the command dir flash: to check IOS is available or not. i found the IOS is there.But it is not boot from IOS.
So i use the coomand boot xxxx.bin to boot from IOS.and finally it booted.
They told to use the coomand confreg in the ROMMON mode.
Cisco Switching/Routing :: 6509 Goes In ROMmon On Reboot
Jul 24, 2011 I am facing a problem with a cisco 6509 that goes into rommon every time i restart. If i give the command
rommon 1> boot
it will pick up the IOS on the sup-bootdisk: or bootdisk: and boots up but i dont understand why on reboot it wont pick up this IOS and boot itself and why do i have to write boot command everytime on rommon.
I have also explicitly given the command "boot system bootdisk:IOSNAME.bin" in the startup config file but still no luck.
Cisco Switching/Routing :: ASA5505 Booting Into ROMmon?
Jul 3, 2012An ASA 5505. Device boots to rommon #0> and stays there. The complete boot record follows:
CISCO SYSTEMS
Embedded BIOS Version 1.0(12)13 08/28/08 15:50:37.45
Low Memory: 632 KB
High Memory: 507 MB
[Code]....
Cisco Switching/Routing :: 871 Not Enter ROMmon After Flash Upgrade
Dec 12, 2012I tired to upgrade the flash memory on my 871. I have tired to send single break and removing the flash card to drop the 871 to rommon. but no luck, all i get is the below error. I have try restart button on the back and get the same results. How to get the router into rommon mode so i can place the IOS on the flash ?
View 5 Replies View RelatedCisco Switching/Routing :: 6513 Switch Boot To ROMmon
May 9, 2012i have a Cisco 6513 it is used one, i have tryed to boot it but it did not work, it alwayes go to rommon mode and i am not able to know what is the issue,
when it boot i get the below outpot from the switch.
System Bootstrap, Version 8.1(3)
Copyright (c) 1994-2004 by cisco Systems, Inc.
Testing lower main memory - data equals address
[Code].....
Cisco Switching/Routing :: 6500 With SUP720 Recovery From ROMmon
Jan 24, 2007if it is possible to recover a Cat 6500 that has no code on bootflash from ROMMON, and is it mandatory to have a compact flash card to do the recovery ? or can one use xmodem or TFTP ?
View 6 Replies View RelatedCisco Switching/Routing :: 6509 Upgrade To 12.2(33)SXI10 And ROMmon?
Dec 12, 2012I have ROM MON version 12.2(17r)S2 and I am trying to determine if I need to chnage this to 12.2(17r)SX7. It does not appear I need to with the upgrade to 12.2(33)SXI10. Is this correct?
View 1 Replies View RelatedCisco Switching/Routing :: 7600 With Ws-sup750 Stuck In ROMmon
Apr 27, 2011I have a 7600 with ws-sup750 and when it boots it displays these errors:
Cisco IOS Software, s72033_sp Software (s72033_sp-ADVIPSERVICESK9_WAN-M), Version 12.2(33)SXH2a, RELEASE SOFTWARE (fc2)Technical Support: [URL]
Firmware compiled 07-Apr-08 22:12 by integ Build [100]
00:00:05: %C6K_PLATFORM-0-UNKNOWN_CHASSIS: The chassis type is not known.(0x6003)
[Code]....
Then it got stuck in rommon, i tried using a 7200 pcmcia card (I downloaded the 7600 IOS there) but if i do from rommon boot disk0:
it complaints with :open: file "c7200-atafslib-m" not found so, it doesn't boot.
Anything I can do to be able to boot this device ?
Cisco WAN :: 2960 - Upgrade Catalyst Switch Software In ROMmon Mode?
Jan 28, 2011How can i Upgrade Catalyst 2960 switch software in Rommon mode (switch:)
Right now flash is empty.
Cisco Switching/Routing :: C2960 / Firmware Error After Upgrade - Cannot Get To ROMmon
Aug 14, 2012Yesterday I tried to install c2960-lanbasek9.mz.12.55.SE4.bin onto my router. When I changed the boot commands, I did not leave the 2nd option in there and the old firmware has an .ex3 extension. After trying to boot to this new image, we receive a looping error message that continues to reboot and go through the same process.Basically the error is "ERROR: firmware not supported by hardware"I have power cycled it a few times but durning bootup, I never see the ################## which would allow me to BREAK sequence and get into rommon. The device simply waits about 30-40 seconds after boot and goes right back to the looping reboot sequence and the error message. Is there any hyper term or putty settings to change on this?
View 1 Replies View RelatedCisco Switching/Routing :: 4510R+E - Dual Sup 7e Software / ROMmon Upgrade?
Jun 1, 2011We have some 4510R+E with dual sup 7e that have experienced problems recently. One of the sup 7e's crashed with a "critical software exception":
#show verCisco IOS Software, IOS-XE Software, Catalyst 4500 L3 Switch Software (cat4500e-UNIVERSALK9-M), Version 03.01.01.SG RELEASE SOFTWARE (fc1)
<snip>
ROM: 15.0(1r)SG1
<snip> Last reload reason: Critical software exception, check bootflash:crashinfo_iosd
So I thought I'd upgrade to IOS-XE 3.2.0SG to hopefully resolve the issue. I was reading the software release notes and it says:
If you are upgrading to 3.2.0SG, you must upgrade your ROMMON to 15.0(1r)SG2.If they have dual supervisors, first upgrade your software to 3.2.0SG, then upgrade your ROMMON to15.0(1r)SG2 to avoid the resets uplinks issue (CSCtj54375).
And from the ROMMON release notes it says:
Download the cat4500+e-promupgrade-150_1r_SG2 program from Cisco.com, and place it on a TFTPserver in a directory that is accessible from the switch that is upgraded.The cat4500+e-promupgrade-150_1r_SG2 program is available on Cisco.com at the same location from which Catalyst 4500 system images are downloaded.
So I have several questions:
The only promupgrade file I can find is cat4500-e-ios-promupgrade-150-1r-SG2 (which doesn't appear to be the same as cat4500+e-promupgrade-150_1r_SG2 ). Where the correct file is?Since I have dual supervisors, it says I should upgrade the software, then the ROMMON. If I can do that (run the new software with the old ROMMON) why am I bothering to upgrade the ROMMON in the first place? (update, ok, I see the new ROMMON gives me enhanced crash info and will allow future upgrades without bringing down both supervisors at the same time).When these were ordered/installed, the licenses were all mixed up (I wasn't involved with that ). So the MDFs have dual sup 7e with ipbase and the IDFs have single sup 7e with enterprise services. Obviously, we want the enterprise services in the MDF so we can run OSPF and the ipbase in the IDF. But, OSPF seems to be running just fine in the MDF on ipbase. Are the licenses not enforced on these platforms? The release notes for 3.2.0 say ipbase doesn't support OSPF. So if I upgrade the MDF switches, will OSPF suddenly stop working?
The IP Base image does not support enhanced routing features such as Nonstop Forwarding (NSF) , BGP, Enhanced Interior Gateway Routing Protocol (EIGRP), Open Shortest Path First (OSPF), Intermediate System-to-Intermediate System (IS-IS), Virtual Routing Forwarding (VRF-lite) and policy-based routing (PBR).