Cisco VPN :: Sonicwall 2400 VPN With 8xx?
Aug 16, 2011
I am building the VPN with Sonicwall and Cisco Router, the VPN status is indicated ok on the Sonicwall and able to ping only,I know it required ACL on Cisco but it failed, I cannot ping the sonicwall from cisco, the access from external to cisco internal is also fail.
Site A SonicWall = 192.168.1.0Site B (Cisco) = 192.168.143.0
crypto isakmp policy 15encr 3desauthentication pre-sharegroup 2lifetime 28800crypto isakmp key XXXXX address 118.142.###.###crypto ipsec security-association lifetime seconds 28800crypto ipsec transform-set T1 esp-3des esp-sha-hmaccrypto map tosonicwall2 15 ipsec-isakmpset peer 118.142.116.146set transform-set T1match address 110 ip nat inside source route-map nonat interface Dialer0 overloadip nat inside source static tcp 192.168.143.20 80 202.64.135.### 80 extendableip nat inside source static tcp 192.168.143.20 3389 202.64.135.### 3389 extendable!access-list 1 permit 192.168.143.0 0.0.0.255access-list 110 permit ip 192.168.143.0 0.0.0.255 192.168.1.0 0.0.0.255access-list 110 deny ip 192.168.143.0 0.0.0.255 anyaccess-list 115 permit ip 192.168.143.0 0.0.0.255 anyaccess-list 115 deny ip 192.168.143.0 0.0.0.255 192.168.1.0 0.0.0.255no cdp run!route-map nonat permit 10match ip address 115!
View 7 Replies
ADVERTISEMENT
Jul 31, 2006
I have an ME2400 running private V LANs. The primary V LAN is 20 and the secondary V LAN's are 21 and 22. Currently, management traffic is still on V LAN 1. My question is now that the ME2400 does not have anything plugged into v lan 1; the line protocol goes down, which means that I can no longer access the switch remotely. Is it possible to keep a SVI up up even though nothing is plugged into that V LAN? If so, how do I go about doing this?
View 2 Replies
View Related
Feb 20, 2013
the 2400 and Wifi though I was unable to find anything specific enough for my scenario.I'm trying to connect my Dell 2400 Desktop to wireless internet using a Wifi USB...It is able to connect to the Router, but unable to connect to the internet. I've gone and downloaded the suggested drivers for the desktop, though still having the same issue. In the bottom right corner of the taskbar it will show a strong connection to the router, though I have a LAN connection that says " Local Area Connection: A Network Cable Is Unplugged" and it lists the connection through Broadcom. Here is the relevant information I have (judging from what previous posts have looked for).First Up, the Wifi USB I'm using is a NetGear WNDA3100V2 GenieI've gone an done the ipconfig, and tried pinging sites, though the pings timed out and returned nothing. The results of the ipconfig are:
Windows IP Configuration
Host Name . . . . . . . . . . . . : Mike
Primary Dns Suffix . . . . . . . :
Node Type . . . . . . . . . . . . : Hybrid
[Code].....
View 1 Replies
View Related
Aug 21, 2012
Before I put in place any network security appliance POC, my wireless network worked fine.Note: ethernet works fine all the time and confirm my internet is okay too. Just wireless.
First time, I got Palo Alto vendor to setup POC. It screwed up my wireless. We removed on 1st day itself and re-configured everything all over again.Now before holiday break, Sonicwall vendor setup POC for us. It worked fine though for 1 week and now the wireless gone crazy again.
3 bars, 2 bars, 5 bars, sometimes no bar.Then when there's POC, my guest wireless network will dead too.
I can't figure out the problem and what's causing such instability?If I understand correctly, this is how my network works:-
sonicwall nsa 2400 (router 192.168.1.1)
cisco linksys wireless (before sonicwall, we used this as router. Now used as wireless access point).
tp-link 48-Port 10/100Mbps + 4-Port Gigabit Web Smart Switch
is there anything in particular I should take note about? or any tools to analyze my wireless network problems?
View 3 Replies
View Related
Jun 8, 2012
My company has a Cisco IAD 2400 which is handling our phones and the internet (from Service Provider). We are adding a second router, a Cisco 1921, to our network,I think I have everything set up correctly. One department is using the 192.168.2.0/27 subnet. I can ping each computer within that subnet. Also, within this subnet, I can ping the router interface at 192.168.2.1. I can ping 192.168.1.2 successfully as well. This is the interface on the 1921 that goes to the 2400. However, if I try to ping 192.168.1.1 (interface on 2400), I get "Reply From 192.168.1.236: Destination Host Unreachable" I get the same thing if I ping 8.8.8.8.Within the 1921, I can ping 192.168.1.1 and 74.125.224.72 (random google ip) successfully.
View 1 Replies
View Related
Oct 5, 2008
I am trying normal password recovery for (cisco routers) for IAD 2400 but iam unable to get in rommon mode ?
View 3 Replies
View Related
Apr 26, 2009
I am using a Negear Wireless USB adapter for the Dell Dimension 2400. The computer can see the wireless adapter in Device Manager; but it does not pick up any wireless signals.
There is a wireless switch to turn on/off for the laptop, but a desktop does not have such feature.
View 4 Replies
View Related
Feb 6, 2012
I have a Dimension 2400 PC and a am about to get awireless router with anew provider. I cannot find a wireless switch so does any one know and if if I can connect?
View 2 Replies
View Related
Feb 5, 2013
I am trying to find a tool that will monitor the web traffic for one specific user. If it is capable of bundling it into a report that would also be a benefit. I have searched, but not come up with much aside from broad network monitoring tools. All that is really needed is to capture all the activity from http traffic for this one specific user/PC (since she uses the same PC all the time). We have a Sonicwall NSA 2400 as our internet filter, but I was not able to locate anything on there for specific user reporting.
View 2 Replies
View Related
May 1, 2005
She has a Dell Dimension 2400, Service Tag 2VG3341 running Win XP Home with Service Pack 2.
At startup we get a message from Norton A/Virus 2003 - Symantec cannot scan your email address, because your network is not properly configured.
Canceling this message and trying to connect to the internet using the Dial –up connection gives this message:
Error 720: A connection to the remote computer could not be established. You might need to change the network settings for this connection.
I have checked the Network Properties as per Windows Troubleshooter, but cannot find anything unusual.
I have also ran the Dell Diagnostic CD, but these tests have are all clear.
The Windows firewall is also disabled
When I try to enable it I get the error message –
Windows Firewall settings cannot be displayed because the associated service is not running. Do you want to start the Windows Firewall Internet Connection Sharing (ICS) service?
After clicking on “Yes” A dialog box shows “Starting the Windows ICS” Then comes the message “Windows cannot start the Windows Firewall /ICS Services”
View 1 Replies
View Related
Aug 2, 2012
I just got my dell dimension 2400 up n running again.
1) I need a new operating system . i know how to do that what with windows being designed to make computers work properly or what is the latest thats not vista or could i just get a copy from a friend? <--- that may not be particularly legal but idc i just want to know if it would work if a new disk is too expensive
2) I need internet connectability i have a working att wireless router brand new just got delivered today and i have a d link wireless reciever thing i just got from my buddy but how to get the internet up n running without boring holes in the floor / wall or dragging a cable 18 miles from the router to the computer so i need it to be wireless
3) I am not sure what to do with it do i just need soft ware updates or do i need hardware updates to get it up to speed with the so called "big boys even though its far larger than any laptop my goal is to have a fast running internet capable game capable and multitasking computer with which i can do.
View 1 Replies
View Related
Oct 29, 2012
I have two CISCO 2800 routers tied together over a Metro Ethernet bewteen an HQ location and a Colocation facility. There are multiple subnets on both sides of the MAN. All things work in this regard.
I added two new Interfaces to the routers to create a VPN failover should the above MAN go down. I use IP SLA to track the MAN, then move to the VPN route when reachability is down.
I can source ping from one CISCO router Interface to the other, through the two interfaces to the Sonicwalls and reach the router interface of the CISCO on the other side of the VPN tunnel.
Problem: I can not ping any subnet behind the interface I ping through the Sonicwall VPN tunnel?
Example 2800 G0/2 interface 100.1.1.41 /30 through Sonicwal over Internet to other Sonicwall and out ot the G0/2 100.1.10.41 /30 interface on the other 2800 router. Ping is fine.
View 15 Replies
View Related
Feb 4, 2009
We have a several SonicWall TZ 190 establishing VPN tunnels with a ASA5520. Pericodically random VPN tunnels will drop and can not re-establish a connection. In order to re-establish the dropped VPN tunnel, our firewall folks manually drop all VPN tunnels connected to the ASA (they use to physically power cycle the ASA). They claim this is the only way to resolve the problem and since the SonicWall Life Time seconds for Phase 1 and 2 are set to 28800, they reset the tunnels every 8 hours. Additionally, they claim that SonicWall IPSEC is different that Cisco IPSEC which is the main problem. Hence they are requesting a SONICWAll VPN concentrator..
View 4 Replies
View Related
Feb 8, 2011
My SIP trunk provider uses a SonicWall Pro 3060, I need to initiate a IPSec VPN tunnel from an ASA 5505 (ASA1) for SIP traffic to a PBX connected on ASA1's inside.ASA1 should also connect a VPN to ASA2, ASA2 has a fixed IP I have not been able to figure out how to initiate the tunnel from the ASA1 to the Sonicwall due to the dynamic IP.
View 3 Replies
View Related
Oct 5, 2012
My internet line is coming directly into HUWAI router and from here its supplying to sonicwall TZ210 WAN port.I have a domain from dyndns.org that is set right now in sonicwall. But when I browse this domain from outsde it opens my HUWAI router login page and I want it to open my SONICWALL login PAGE.
View 2 Replies
View Related
Mar 18, 2013
Which is a better firewall without looking at all the additional services you can purchase on a Sonicwall.
View 19 Replies
View Related
Dec 11, 2012
It's been awhile since work has thrown me a curve ball so I was about due. We've got a client that wants us to log into their secure portal, this is normally not a issue. The link they sent us to their 'portal' apparently takes us to the wrong page. Their solution to this is for us to create a DNS entry to resolve that URL to a specific IP address. We don't currently have a DNS server setup in house so I assumed this would be something done on the Sonicwall.
I asked them why I couldn't just go to the IP address instead of the URL anyway and they said it wouldn't work. Is this something that I can maybe create a NAT Policy for and have it redirect traffic to there? I know the SonicWall has a DNS tab but I've never touched it and I'm not sure what I would need to put in there anyway.
View 7 Replies
View Related
Dec 9, 2012
I'm having a hard time finding which Verizon 3g usb phone cards that will work with a TZ105. How to get it working on a TZ105, what usb phone card you're using and the phone provider. Sonicwall support is telling me there are no verizon cards that will work right now. I have my Sonicwall vendor looking into it, but still haven't heard back from him either. So at this point I'm looking for any USB 3g phone card that is known to work.
View 11 Replies
View Related
May 19, 2011
Hardware Configuration:
Office 1: Sonicwall TZ200 (192.168.11.xx)
Office 2: Sonicwall TZ100 (192.168.12.xx)
Home Office: Linksys RV042 v1 (192.168.13.xx)
The VPN tunnel between Office 1 and Office 2 is functioning.
The VPN tunnel Office 1 and HomeOffice has been established, BUT I cannot ping any subnets across the tunnel. I have tried different settings, and will post the current configuration later.
this setup and can post their respective settings.
View 2 Replies
View Related
Apr 24, 2013
I am looking to setup for BGP with the following conditions:
Client has two 2900 routers, each connecting to a seperate ISP
Client has a Sonic Firewall with a link to each router
Client owns their own /24 block of public IPs and has their own AS Number.
Client has a public /24 and /25 from the corresponding ISPs
Client has supplied the following routing rules they would like to use:
-Anything from their own public subnet should advertize via the two ISP's with best path selection
-Anything from the respective ISP public subnets should use only their link (The ISP's are not auth'd to advertize the other's network)
The two routers are directly connected to eachother and each has a link going to the Sonicwall.
View 5 Replies
View Related
May 22, 2011
Hardware Configuration:
Office 1: Sonicwall TZ200 (192.168.11.xx)
Office 2: Sonicwall TZ100 (192.168.12.xx)
Home Office: Linksys RV042 v1 (192.168.13.xx)
The VPN tunnel between Office 1 and Office 2 is functioning.The VPN tunnel Office 1 and HomeOffice has been established, BUT I cannot ping any subnets across the tunnel. I have tried different settings, and will post the current configuration later.
View 4 Replies
View Related
May 15, 2013
I am attempting to get a NAT connection to work through a Sonicwall TZ200 to a VLAN defined on a Cisco 3750 switch. So far I have not been able to get it to work. I am able from the VLAN to access the internet and devices on another VLAN.
I have reviewed the configuration of the Sonicwall with Sonicwall support. They checked and see no issue with the configuration. I have the NAT gateway set to the vlan gateway IP address.
Are there any particular configuration options that I need to set on the 3750 switch in order to be able to route the traffic from the internet to the VLAN?
View 4 Replies
View Related
Jan 11, 2012
I have my modem then a switch, and two gateways a Cisco 800, and a sonicwall tz170.The Cisco isn't managed by me, it's on a 172.18.2.x subnet and I only have about 12 addressable IPs.I manage the sonicwall and have all 254 addresses open. The computers have to stay behind the Cisco because it connects to a VPN that the line of business software uses.
I can't connect the two gateways by VPN because I cant control the Cisco.How can I get these two to talk? I have a new server on the sonicwall network and an old server on the Cisco network. I want the computers to be able to see both servers
View 13 Replies
View Related
Apr 5, 2011
How do I block specific domains (pandora.com, etc.) in the Sonicwall? It seems like this would happen in the CFS but do I need a subscription for this? I don't want to subscribe to Sonicwall's filtering list, I just want to block a couple specific domains.
View 9 Replies
View Related
Mar 24, 2011
At work, I am able to connect to sonicwall and log onto SAP.At home, I am able to connect to sonicwall, yet I can't get onto SAP.I am sure that this is a non-SAP related issue because I can use other VPN's to connect to other SAP systems. In control panel -> view network status, sonicwall says 'unidentified network' which I believe is causing the issue. Normally it wouldn't say this
View 1 Replies
View Related
May 10, 2011
I need to replace my old sonicwall firewall. I was looking at the latest Sonicwalls, but they are really expensive if you get all of the services. For the TZ 210 - if I go for just the firmware updates without the gateway security services, how much better of a firewall is it than a Netgear fvs336g?
View 3 Replies
View Related
Dec 17, 2012
Not sure what's going on with this thing. Unfortunately I'm 3 hours away from where it's installed. We put it in place about 3 months ago. It's set to use failover and load balancing. When I installed it I tested the failover and load balancing and everything worked as it should. The past 2 weeks the unit has not been failing over when one ISP drops. This requires a power cycle of unit to get the secondary on X2 to pick up. Data collection is turned off. Probing is turned on for both WAN ports. While both ISP's are up it load balances fine. I was there last week and pulled the patch cables going to the modems and it didn't skip a beat doing a constant ping. Just randomly it takes a shit when one ISP goes down. Takes out the network as well as no internal resources are reachable as well. Can't ping the server from any PC's and such.
It's running an older firmware. 5.5.6 from Nov 2011. 5.8 is currently available. I'm just leery about flashing a new firmware remotely.
Anything like this before with these units? We have plenty of 170's and 180's in place that are trouble free.
View 6 Replies
View Related
Oct 17, 2011
I am looking for a Cisco firewall to replace a Sonicwall NSA240 firewall in SME environment?
View 3 Replies
View Related
Nov 5, 2011
I am trying to setup a VPN tunnel between a Cisco ASA 5510 (Version 8.2(2)) and Sonicwall TZ200. I got tunnel up and going and I am able to ping the Cisco ASA internal IP from the Sonicwall LAN but nothing else works.
When I try to ping a host behind the Cisco ASA from the Sonicwall LAN I get the following message "Asymmetric NAT rules matched for forward and reverse flows;
[code]...
View 14 Replies
View Related
May 24, 2011
I am trying to make an IPSEC tunnell between a 857 and a Sonicwall NSA240.The tunnell goes up but the traffic from the 857 seems to be pushed outside the router to the public internet, not into the tunnel.
Following configuration:
crypto isakmp policy 1 encr 3des hash md5 authentication pre-share group 2 lifetime 28800crypto isakmp key xxxxx address 111.111.111.111 no-xauth!crypto ipsec security-association lifetime seconds 28800!crypto ipsec transform-set xxxx esp-3des esp-md5-hmac!crypto map xxxx 1 ipsec-isakmp description VPN to xxxx set peer 1111.111.1111.111 set security-association lifetime seconds 3600 set transform-set xxxx set pfs group2 match address 115
ip forward-protocol ndip route 0.0.0.0 0.0.0.0 Dialer0!
access-list 115 permit ip 172.28.3.0 0.0.0.255 192.168.22.0 0.0.0.255
If I try a traceroute the traffic is not pushed into the tunel but it seems the it tries to route the traffice over the internet using Dialer0.
View 4 Replies
View Related
Sep 16, 2012
i have one sonicwall NSA 240. it is directly connected to ISP and other interface connected with cisco Layer 2 switch. my que. is that. how to access that sitch remotely ??
sonicwall 1st interface connected with ISP (pubilc IP) and 2nd interface connected with cisco switch with private IP bocz there NAT configuration. i m able to access sonicwall and i m getting ping up to sonicwall bt i cann't able to ping cisco switch.. i think some i need a some missing in sonicwall configution like telnet or VPN
View 1 Replies
View Related
Mar 20, 2011
When I start the installation of sonicwall vpn client 2.4 in Windows 7 that sends me the following message "unable to manage networking component. operating system corruption may be preventing installation".I use the version 2.4 Windows 7 32-bit?
View 2 Replies
View Related
Sep 1, 2011
we got a Sonicwall router and we have been having stability issues. Every 1 minute the TCP connectio is dropped as well as UDP packets. This router is connected to a T1 connection and its requesting a DHCP lease every couple minutes as well. We originally had two WAN connections, and we have disabled the second one because someone thought it was that, but obviously it has to do with the internal network. This is a dual WAN router.
View 4 Replies
View Related
