My SIP trunk provider uses a SonicWall Pro 3060, I need to initiate a IPSec VPN tunnel from an ASA 5505 (ASA1) for SIP traffic to a PBX connected on ASA1's inside.ASA1 should also connect a VPN to ASA2, ASA2 has a fixed IP I have not been able to figure out how to initiate the tunnel from the ASA1 to the Sonicwall due to the dynamic IP.
View 3 RepliesTrying to connect a 5505 with a dynamic address on 8.3(2) to a static IP'd asa (5510 on 8.2(1) with a DefaultL2LGroup and dynamic maps already created.
Inside networks:
Local (5505) 192.168.100.0 /24
Remote (5510) 10.100.1.0 /24
Configuration on 5505
isakmp policy 20 authentication pre-share isakmp policy 20 encryption 3des isakmp policy 20 hash md5 isakmp policy 20 group 2 isakmp policy 20 lifetime 3600 isakmp enable outside access-list 100 extended permit ip 192.168.100.0 255.255.255.0 10.100.1.0 255.255.255.0nat (inside,any) 0 access-list 100tunnel-group DefaultL2LGroup ipsec-attributes pre-shared-key *****crypto ipsec transform-set myset esp-3des esp-md5-hmac crypto dynamic-map cisco 1 set transform-set myset crypto map dyn-map 20 ipsec-isakmp dynamic cisco crypto map dyn-map interface outside
I updated the configuration per your response below... It still doesn't work. See my new config files below.
make follow changes on host: officeasa
remove this line below highlighted.
crypto dynamic-map L2LMap 1 match address Crypto_L2L
It is only because group1 is weak, so please change it to group2
crypto dynamic-map L2LMap 1 set pfs group1
route outside 10.10.6.0 255.255.255.0 96.xxx.xxx.117
[code].....
I'd like to connect through a VPN the HQ office to a Branch using two ASAs.I have a 5520 in the HQ and 5505 in the Branch Office.My problem is in the Branch office where I have a dynamic IP (ADSL).
I couldn't find a example this kind of configuration.
There are three different sites, two are composed of Multilayer switches cisco 3560 and 3570 as core switches (a 3560 in one site and a 3570 in another site), the last site doesn't have any routers just a 2950 switch. Each site has two asa 5505 as firewalls. Two Internet connexions are connected to every site, one on every firewall. One Internet line is used to connect the different sites together using VPN crypted with IPsec and the other line is just for Internet access. The line that is used to interconnect sites contains voice and data traffic.At the moment all the routes are static routes, the network isn't too big for now and counts not more than 20 subnets.But it is evolving, and I want to use dynamic routing, EIGRP to be more accurate. I've looked into it and I'm not sure how to make it work. The VPNs active on the ASAs don't support dynamic routing, so I thought about GRE tunnels but the ASAs don't seem to allow it either.
View 11 Replies View RelatedHow to get DynDNS or some other public dynamic DNS services on the Internet working on ASA 5505?
View 2 Replies View RelatedI'm having some issues configuring NAT statements on my ASA5505 which has recently been upgraded to 8.41.
I have a single dynamic IP on the outside interface of the ASA and would like all internal hosts to NAT/PAT to it. In addition, I would like to have several ports 'forwarded' to internal hosts, one of which is TCP/4343. With the current configuration all hosts are NATing to the external interface properly but the service running on TCP/4343 is not accessible from the outside. See command output below:
"sh run object" output:
object network DrJones host 10.81.220.90object network LAN-10.81.220.0 subnet 10.81.220.0 255.255.255.0
"sh run nat" output:
object network DrJones nat (inside,outside) static interface service tcp 4343 4343object network LAN-10.81.220.0 nat (inside,outside) dynamic interface
"sh run access-list" output:
access-list inside_access_in extended permit ip 10.81.220.0 255.255.255.0 anyaccess-list outside_access_in extended permit icmp any any echo-replyaccess-list outside_access_in extended permit tcp any interface outside eq 4343
I wanted to move to the cisco arena, and having a bugger of a time figuring out simple nat/pat rules combined with access lists. I've been reading Richard Deal's Cisco ASA configuration book, googling the heck out of this simple problem and can't see what I'm missing.
I have an ASA 5505 unlimited security plus license running 8.2(3) and a simple network, 192.168.0.x internal, 192.168.3.x dmz (not even touching that yet!) and outside I have a /29 subnet of addresses, 25 is the gateway, and 26-30 are my addresses.
I have simple dynamic nat set up on the .26 address to nat to 192.168.0.x. All I'm trying to do is port forward a simple tcp port I set for my linux server (192.168.0.2) on the inside, for arguement's sake, it's 2222 (it's not really). My outside vlan 50 is X.X.X.226 255.255.255.248 , can I make a static nat (inside,outside) x.x.x.226 192.168.0.2 netmask 255.255.255.255 ?
I tried using (inside,outside) x.x.x.230 192.168.0.2 netmask 255.255.255.255 and that didn't work either. Is it not possible to use two external addresses to hit the entire /24 range AND a single server?
My access rule for this nat is permit tcp any 192.168.0.2 eq 2222 (where I'm using 2222 for my ssh port). then I apply that access list to the access group interface "outside".
I thought the outside interface would do a proxy arp (since I do not have the sysopt noproxyarp command) for my 227,228,229, and 230 addresses where .226 is my internal nat for all my internal machines i.e. 192.168.0.1 -> x.x.x.226 . I had this working like a charm before with my fortinet, so I know I have systems listening.
I'm working on setting up a template configuration for the Cisco ASA 5505 device that we'll use to configure more routers for various client needs. One of the requirements requested of me is the following: Internal hosts assigned a DHCP address are blocked from the internet Internal hosts with a static IP are permitted access to internet All internal hosts can communicate regardless of state
Now, I'm fairly new to this and I'm certain my terminology isn't correct so googling the problem has been fruitless. I have followed basic configuration guides and have configured the device to hand out DHCP addresses to hosts plugged in ports 1-7. If I'm plugged in and specify my address manually in the OS I am blocked from any access so I can only assume there is an access policy or some rule preventing me from authenticating against the router despite having set up VLAN1 to be the entire class C subnet. What sort of steps would I need to do to configure this? New access lists. For the record, the dhcp addresses are in the range of 10.100.31.64-10.100.31.95. VPN users are assigned an address from 10.100.31.220-10.100.31.240 and there seems to be no issues with that configuraiton. I don't wish to constrain what addresses a user can use should they specify a static IP (10.100.31.5 should be just as valid as 10.100.31.100).
I have an ASA5505 running which is on a static IP. I have just got an SRP527W for a remote worker and want to create a site-to-site VPN into the ASA. I have a number of other router of non-cisco brand which just all dial-in and connect no problem.
On other routers I have been abloe to specify the DDNS hostname in the VPN setup so that the ASA can identify it. I'm not sure how I setup the SRP527 to connect to the ASA.
I have some sites already connected with ASA 5505 site to site VPN with both end static IP. Normally, all traffic can come across without any problem. Even I used "management-access inside" for both ASA.Now I have a new office with only ADSL pppoe connection. I used easy VPN to connect from Site B:remote dynamic IP site to SiteA:static IP with similar example of this: [URL]
All my 5505 ASA are running 8.4(4)1
Site A - Static IP
Site B - dynamic IP with pppoe connection.
After EasyVPN connected, i do not know how do I remote manangment from site A lan to site B 5505 ASA?
I have two CISCO 2800 routers tied together over a Metro Ethernet bewteen an HQ location and a Colocation facility. There are multiple subnets on both sides of the MAN. All things work in this regard.
I added two new Interfaces to the routers to create a VPN failover should the above MAN go down. I use IP SLA to track the MAN, then move to the VPN route when reachability is down.
I can source ping from one CISCO router Interface to the other, through the two interfaces to the Sonicwalls and reach the router interface of the CISCO on the other side of the VPN tunnel.
Problem: I can not ping any subnet behind the interface I ping through the Sonicwall VPN tunnel?
Example 2800 G0/2 interface 100.1.1.41 /30 through Sonicwal over Internet to other Sonicwall and out ot the G0/2 100.1.10.41 /30 interface on the other 2800 router. Ping is fine.
I am building the VPN with Sonicwall and Cisco Router, the VPN status is indicated ok on the Sonicwall and able to ping only,I know it required ACL on Cisco but it failed, I cannot ping the sonicwall from cisco, the access from external to cisco internal is also fail.
Site A SonicWall = 192.168.1.0Site B (Cisco) = 192.168.143.0
crypto isakmp policy 15encr 3desauthentication pre-sharegroup 2lifetime 28800crypto isakmp key XXXXX address 118.142.###.###crypto ipsec security-association lifetime seconds 28800crypto ipsec transform-set T1 esp-3des esp-sha-hmaccrypto map tosonicwall2 15 ipsec-isakmpset peer 118.142.116.146set transform-set T1match address 110 ip nat inside source route-map nonat interface Dialer0 overloadip nat inside source static tcp 192.168.143.20 80 202.64.135.### 80 extendableip nat inside source static tcp 192.168.143.20 3389 202.64.135.### 3389 extendable!access-list 1 permit 192.168.143.0 0.0.0.255access-list 110 permit ip 192.168.143.0 0.0.0.255 192.168.1.0 0.0.0.255access-list 110 deny ip 192.168.143.0 0.0.0.255 anyaccess-list 115 permit ip 192.168.143.0 0.0.0.255 anyaccess-list 115 deny ip 192.168.143.0 0.0.0.255 192.168.1.0 0.0.0.255no cdp run!route-map nonat permit 10match ip address 115!
We have a several SonicWall TZ 190 establishing VPN tunnels with a ASA5520. Pericodically random VPN tunnels will drop and can not re-establish a connection. In order to re-establish the dropped VPN tunnel, our firewall folks manually drop all VPN tunnels connected to the ASA (they use to physically power cycle the ASA). They claim this is the only way to resolve the problem and since the SonicWall Life Time seconds for Phase 1 and 2 are set to 28800, they reset the tunnels every 8 hours. Additionally, they claim that SonicWall IPSEC is different that Cisco IPSEC which is the main problem. Hence they are requesting a SONICWAll VPN concentrator..
View 4 Replies View RelatedMy internet line is coming directly into HUWAI router and from here its supplying to sonicwall TZ210 WAN port.I have a domain from dyndns.org that is set right now in sonicwall. But when I browse this domain from outsde it opens my HUWAI router login page and I want it to open my SONICWALL login PAGE.
View 2 Replies View RelatedWhich is a better firewall without looking at all the additional services you can purchase on a Sonicwall.
View 19 Replies View RelatedIt's been awhile since work has thrown me a curve ball so I was about due. We've got a client that wants us to log into their secure portal, this is normally not a issue. The link they sent us to their 'portal' apparently takes us to the wrong page. Their solution to this is for us to create a DNS entry to resolve that URL to a specific IP address. We don't currently have a DNS server setup in house so I assumed this would be something done on the Sonicwall.
I asked them why I couldn't just go to the IP address instead of the URL anyway and they said it wouldn't work. Is this something that I can maybe create a NAT Policy for and have it redirect traffic to there? I know the SonicWall has a DNS tab but I've never touched it and I'm not sure what I would need to put in there anyway.
I'm having a hard time finding which Verizon 3g usb phone cards that will work with a TZ105. How to get it working on a TZ105, what usb phone card you're using and the phone provider. Sonicwall support is telling me there are no verizon cards that will work right now. I have my Sonicwall vendor looking into it, but still haven't heard back from him either. So at this point I'm looking for any USB 3g phone card that is known to work.
View 11 Replies View RelatedHardware Configuration:
Office 1: Sonicwall TZ200 (192.168.11.xx)
Office 2: Sonicwall TZ100 (192.168.12.xx)
Home Office: Linksys RV042 v1 (192.168.13.xx)
The VPN tunnel between Office 1 and Office 2 is functioning.
The VPN tunnel Office 1 and HomeOffice has been established, BUT I cannot ping any subnets across the tunnel. I have tried different settings, and will post the current configuration later.
this setup and can post their respective settings.
I am looking to setup for BGP with the following conditions:
Client has two 2900 routers, each connecting to a seperate ISP
Client has a Sonic Firewall with a link to each router
Client owns their own /24 block of public IPs and has their own AS Number.
Client has a public /24 and /25 from the corresponding ISPs
Client has supplied the following routing rules they would like to use:
-Anything from their own public subnet should advertize via the two ISP's with best path selection
-Anything from the respective ISP public subnets should use only their link (The ISP's are not auth'd to advertize the other's network)
The two routers are directly connected to eachother and each has a link going to the Sonicwall.
Hardware Configuration:
Office 1: Sonicwall TZ200 (192.168.11.xx)
Office 2: Sonicwall TZ100 (192.168.12.xx)
Home Office: Linksys RV042 v1 (192.168.13.xx)
The VPN tunnel between Office 1 and Office 2 is functioning.The VPN tunnel Office 1 and HomeOffice has been established, BUT I cannot ping any subnets across the tunnel. I have tried different settings, and will post the current configuration later.
I am attempting to get a NAT connection to work through a Sonicwall TZ200 to a VLAN defined on a Cisco 3750 switch. So far I have not been able to get it to work. I am able from the VLAN to access the internet and devices on another VLAN.
I have reviewed the configuration of the Sonicwall with Sonicwall support. They checked and see no issue with the configuration. I have the NAT gateway set to the vlan gateway IP address.
Are there any particular configuration options that I need to set on the 3750 switch in order to be able to route the traffic from the internet to the VLAN?
I have my modem then a switch, and two gateways a Cisco 800, and a sonicwall tz170.The Cisco isn't managed by me, it's on a 172.18.2.x subnet and I only have about 12 addressable IPs.I manage the sonicwall and have all 254 addresses open. The computers have to stay behind the Cisco because it connects to a VPN that the line of business software uses.
I can't connect the two gateways by VPN because I cant control the Cisco.How can I get these two to talk? I have a new server on the sonicwall network and an old server on the Cisco network. I want the computers to be able to see both servers
How do I block specific domains (pandora.com, etc.) in the Sonicwall? It seems like this would happen in the CFS but do I need a subscription for this? I don't want to subscribe to Sonicwall's filtering list, I just want to block a couple specific domains.
View 9 Replies View RelatedAt work, I am able to connect to sonicwall and log onto SAP.At home, I am able to connect to sonicwall, yet I can't get onto SAP.I am sure that this is a non-SAP related issue because I can use other VPN's to connect to other SAP systems. In control panel -> view network status, sonicwall says 'unidentified network' which I believe is causing the issue. Normally it wouldn't say this
View 1 Replies View RelatedI need to replace my old sonicwall firewall. I was looking at the latest Sonicwalls, but they are really expensive if you get all of the services. For the TZ 210 - if I go for just the firmware updates without the gateway security services, how much better of a firewall is it than a Netgear fvs336g?
View 3 Replies View RelatedNot sure what's going on with this thing. Unfortunately I'm 3 hours away from where it's installed. We put it in place about 3 months ago. It's set to use failover and load balancing. When I installed it I tested the failover and load balancing and everything worked as it should. The past 2 weeks the unit has not been failing over when one ISP drops. This requires a power cycle of unit to get the secondary on X2 to pick up. Data collection is turned off. Probing is turned on for both WAN ports. While both ISP's are up it load balances fine. I was there last week and pulled the patch cables going to the modems and it didn't skip a beat doing a constant ping. Just randomly it takes a shit when one ISP goes down. Takes out the network as well as no internal resources are reachable as well. Can't ping the server from any PC's and such.
It's running an older firmware. 5.5.6 from Nov 2011. 5.8 is currently available. I'm just leery about flashing a new firmware remotely.
Anything like this before with these units? We have plenty of 170's and 180's in place that are trouble free.
I am looking for a Cisco firewall to replace a Sonicwall NSA240 firewall in SME environment?
View 3 Replies View RelatedI am trying to setup a VPN tunnel between a Cisco ASA 5510 (Version 8.2(2)) and Sonicwall TZ200. I got tunnel up and going and I am able to ping the Cisco ASA internal IP from the Sonicwall LAN but nothing else works.
When I try to ping a host behind the Cisco ASA from the Sonicwall LAN I get the following message "Asymmetric NAT rules matched for forward and reverse flows;
[code]...
I am trying to make an IPSEC tunnell between a 857 and a Sonicwall NSA240.The tunnell goes up but the traffic from the 857 seems to be pushed outside the router to the public internet, not into the tunnel.
Following configuration:
crypto isakmp policy 1 encr 3des hash md5 authentication pre-share group 2 lifetime 28800crypto isakmp key xxxxx address 111.111.111.111 no-xauth!crypto ipsec security-association lifetime seconds 28800!crypto ipsec transform-set xxxx esp-3des esp-md5-hmac!crypto map xxxx 1 ipsec-isakmp description VPN to xxxx set peer 1111.111.1111.111 set security-association lifetime seconds 3600 set transform-set xxxx set pfs group2 match address 115
ip forward-protocol ndip route 0.0.0.0 0.0.0.0 Dialer0!
access-list 115 permit ip 172.28.3.0 0.0.0.255 192.168.22.0 0.0.0.255
If I try a traceroute the traffic is not pushed into the tunel but it seems the it tries to route the traffice over the internet using Dialer0.
i have one sonicwall NSA 240. it is directly connected to ISP and other interface connected with cisco Layer 2 switch. my que. is that. how to access that sitch remotely ??
sonicwall 1st interface connected with ISP (pubilc IP) and 2nd interface connected with cisco switch with private IP bocz there NAT configuration. i m able to access sonicwall and i m getting ping up to sonicwall bt i cann't able to ping cisco switch.. i think some i need a some missing in sonicwall configution like telnet or VPN
When I start the installation of sonicwall vpn client 2.4 in Windows 7 that sends me the following message "unable to manage networking component. operating system corruption may be preventing installation".I use the version 2.4 Windows 7 32-bit?
View 2 Replies View Relatedwe got a Sonicwall router and we have been having stability issues. Every 1 minute the TCP connectio is dropped as well as UDP packets. This router is connected to a T1 connection and its requesting a DHCP lease every couple minutes as well. We originally had two WAN connections, and we have disabled the second one because someone thought it was that, but obviously it has to do with the internal network. This is a dual WAN router.
View 4 Replies View Related