Cisco Infrastructure :: 1410 Wireless Bridge - Expand Terrestrial Network Across To Uncabled Area
May 31, 2011
I have recently had to deploy a 1410 in a Root/Non-root bridge configuration to expand a terrestrial network across to an uncabled area.
All switches in play are 2960 series and the bridge is running with multiple Vlans.
Basic config as follows.
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryptionservice sequence-numbers!hostname BRIDGE001!no logging consoleenable secret 5(code)
View 1 Replies
ADVERTISEMENT
Aug 8, 2011
Point to point wireless connectivity configuration procedure using 1410 bridges either using GUI/CLI .
We have setup this in one of our Client sites.
View 1 Replies
View Related
Apr 18, 2013
A customer has a wireless PTP bridge using a pair of 1410 bridges. The non-root bridge event log shows the RSSI polling information message indicating the link's signal strength; ie. -42 dBm. It updates every few seconds or so. The root bridge does not show this information in the event log. Both bridges have the event log configuration options set identically, all messages types are enabled. I can't find any reference to this in the documents. Is this by design? I thought that maybe a root bridge if it was set up as a multi-point might be overwhelmed if it was showing/scrolling RSSI from multiple non-roots.
View 3 Replies
View Related
Apr 19, 2011
how far apart an Aironet 1410 Bridge can be from the Power Injector (Dual Coax feeds). I just can't find the specification details. The device comes with a 20' and 50' F-type and I'm looking at 150' runs for both ends of the bridge pair.
View 2 Replies
View Related
Oct 22, 2011
expanding my WiFi coverage over a pretty large ares like 4 or 5 access points.
View 3 Replies
View Related
Sep 29, 2009
I just installed a Linksys WRT160N router. The signal started of good about 50 to 70 feet from the routers location. Now the signal is registering as low to good, about 54Mbps. I was wondering what options I might have to install a wireless bridge for expansion of the signal. I have configured an encrypted network using WPA2. I am wondering what the technical difficulty would be to install and configure it. I setup the WRT160N myself if that means anything.
View 4 Replies
View Related
Jul 23, 2011
I am trying to set up a wifi hotspot with my wireless adaptor. The connection between my ipod and the wireless adaptor in my computer seems to be working fine, but it doesn't connect further to the local area connection (ethernet).I tried to bridge the two networks but it doesn't work I get the error message "An unexpected error occurred while configuring the network bridge"[CODE]
View 4 Replies
View Related
Sep 27, 2011
I have a wrt160n that I would like to use to expand the range of my wireless network. I have tried a few solutions, but to no avail. I am thinking I have just not found the proper steps.I am behind a dsl wireless router that Telus has provided me. The values of that router setup are as follows:SSID: TELUS4108WPA/WPA2-AESDefault gateway: 75.156.190.1DNS address: 199.185.220.254Subnet mask: 255.255.255.0
View 9 Replies
View Related
Aug 2, 2012
I have a network which was recently switched from dsl to comcast. The default network is 10.1.10.1. The dhcp is working with the 5 or 6 installed pc's. All pc's are running xp professional.I inserted the dlink 4 port switch to add a new port by inserting it between the router and a pc.
View 4 Replies
View Related
Jul 6, 2011
I have a netgear CVG834G main router, were my desktop is plugged on to.I pulled a new cable trough the house and garage to have internet access on the other side (cable length is about 80 meters).After the 80meters of cable I placed a Linksys WRT54GS v5.1 router. The problem is that I can connect to the Linksys, but the Linksys can�t connect to the netgear. On the Linksys the internet LED is blinking very slowly (what does this mean?). So first I thought that the cable was broken or too long. I tested the cable => not broken. I connected the Linksys with the netgear trough a shorter cable and then connected my laptop via the long cable (80meter) and this works perfectly.Is the maximum distends a netgear can take less than 80 meters? (thought is was 100meter ).
View 3 Replies
View Related
Apr 27, 2012
I just picked up a 24 port Catalyst 2950 to expand my home network and learn a bit more about networking. Having just upgraded the IOS software 'm now trying to get this to work as required on my network but I'm having a few issues.
My intentions are to plug my cable router/modem wan connection which is set up as the dhcp server to fa 0/1, then use fa 0/2 - 24 for the rest of my wired network. So essentially all on the same subnet interfacing with the router 192.168.0.1.
So far I have set up all of the security on the switch, and have all switch ports assigned to vlan1 with no IPs. My laptop connected to fa0/2 however is not assigned an ip address. Looking at a few posts I ahve rightly or wrongly played about with dhcp snooping.
Config
Current configuration : 2205 bytes
!
version 12.1
no service pad
service timestamps debug uptime
service timestamps log uptime
service (code)
View 3 Replies
View Related
Jul 6, 2005
When I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
View 3 Replies
View Related
Jun 22, 2011
I have a point to point link of 9.27 km using 1410 bridges and AIR-ANT58G28SDA-N antennas as per the documentation that would be an easy to deploy link and it should work at 54 Mbps, eventhough it drops the link, it's so slow and the power measurments indicate -70 dbm (aprox) right under the antenna which is at 9 m height.
This is not the first time I have troubles with 1410 bridges, the other two times I had to change them for 1310 bridges. I wonder if it has to do with some configuration tunning like, external antena gain, link distance or anything else? By the wat this is ocurring in México don't know if that might be worth of taking into consideration in order to deploy a 1410 link.
View 3 Replies
View Related
Aug 2, 2011
security configuration of the 1410 bridge and on how to test the bandwidth/throughput between two 1410 Bridges setup for point-to-point connectivity.
We have setup this in one of our Client sites.
View 3 Replies
View Related
Feb 21, 2012
I have two 1410 bridges installed in a point to point link using external directional antennas. The distance between the bridges is only 200M. As you can see below from the output the RSSI and SNR are excellent with a good fade margin available. These stats are almost identical to what my path profile calculated out to be. During normal operation the latency on this link sub 2ms, during certain conditions the latency jumps to 40+ms and starts dropping packets. I say certain conditions because we have not been able to pinpoint it. Unfortunately at this time the customer does not have the ability to do any SNMP polling or collect any statistical information (working on getting this setup). There are an excessive number of data retries and am not sure if that is normal. During the issues I have observered the below command output and the numbers did not change, which leads to me believe that it is not a RF issue. It almost looks like it's serialization delay, but I have no data to back that up. During iperf performance testing of this wireless link I could push 54Mbps of UDP traffic no problem, no errors, no CRC's.
Bridge Parameters
Encryption: WPA-PSK w/TKIP
Distance parameter: Configured to 1
[Code].....
View 4 Replies
View Related
Feb 6, 2012
How do I configure a local area net work with unbounded media?
View 1 Replies
View Related
Jun 5, 2011
I have a D-link DIR-655. Which that along side with my modem is located downstairs. The upstairs living room has a crappy signal where loading videos becomes painfully slow. Awhile ago, I just tried to relocate my router upstairs and just drill a hole for a CAT cable to slip through to the modem downstairs from my room(as my room is directly above the router)...3 useless holes later, for whatever reason it is impossible to drill through. What are my other solutions?
View 1 Replies
View Related
Jan 29, 2011
I have a WAP 4400n and need to expand the range.Linksys support suggested WAP200 to repeat the signal, but I am probably missing something, because its not working.WAP200 can see the WAP4400n, recognizes its MAC adress, but does not work.Anything to set on the WAP4400n to let the signal to be repeated?
View 11 Replies
View Related
Aug 17, 2012
My brother has a router for his house which lives right next door. I am getting wireless through a adapter right now but not good throughout my house.
View 1 Replies
View Related
Mar 17, 2012
I am planning to deploy a "Digital Notice Board system" in my office, which gets feed from web server and display data/stream on LCD Screen. Well i am done with implementing all the interface on server side and its working pretty well with client side computer. But instead of using Client Side Computer, I just want to use LCD and make some network interface of Local Area Network directly with LCD (to save cost/installation/maintenance of a dedicated computer with LCD ).
View 1 Replies
View Related
Dec 1, 2012
I have 3 switches
Catalyst 2960
Catalyst 3750
Hp procurve 1410 24g
I want to link them using fiber as they are almost 50 meters apart. What connectors should I use and what fiber optic cable can be connected to those connectors.I have found these connectors and cables on internet will these work
GBM-7000-S85 - 1000Base-SX, multi-mode, 550m, 850nm GBIC transceiver
SC to SC Multimode Duplex High Speed Fiber Optic Ethernet Patch Cable 62.5/125
View 1 Replies
View Related
May 18, 2011
I have a Dlink Wireless N Xtreme DIR-655 I have run out of port 4 on it to a switch with a cat 5 patch cable that is 25 ft long It is connected to the Internet port on a Dlink 4 port switch. When i run from that on any of the 4 ports back to my computer ( Win7). I get no internet access but if i connect the cable straight from the router there is no problem. I even attempted to use a older dlink router for the switches and no luck there at all. Any reason the internet would not be broadcasting through the switch.
View 3 Replies
View Related
Jul 5, 2012
I cant find any wds setting in the UI.I want to bridge my old route for wifi expanding
View 3 Replies
View Related
Aug 16, 2011
My DSL Modem connected right now to Linksys Model: WRT600N (Dual Band Wireless-N Gigabit Router) to give a wireless internet access in my house. I have TWO spare Linksys Wireless Router (WRT350N-Wireless-N Gigabit Router) and (WRT54G2-Wireless-G Broadband Router) that I need to use to expand my wireless network at home.
How can i connect the two routers to became an access point or range expander to existing router. It is possible the two spare routers became an access pt or expander? How can i configure that? Cable configuration?
View 1 Replies
View Related
Aug 4, 2011
I have a wireless network in a 2 storey house. The internet access and 1 WRT54GS router is on the 1st floor (using frequency channel 11). The wireless single doesn't do very well on the second floor unless there is a device with a strong antenna. I recently purchased a WET610N Bridge and I have an extra WRT54GS (using frequency channel 1).
I would like to be able to add wireless to the 2nd floor by attaching the extra router to the bridge which would wirelessly connect to the router with the internet.
View 2 Replies
View Related
Feb 26, 2012
I'm using a router WAG320N in my home but now i need to expand my lan with another ports and wireless coverage.In a wired point (connect directly to the router) i need 3 ehternet ports and a repetear of a wireless signal.The optimal solution woulb be a switch gigabit with an integrated acces point, but I understand that there is no such thing...So going to buyng the switch SE2500 and the AP WAP610N... but then I realized the existence of the bridge WES610N!But the information on the linksys italian site is not enough and the relative page does not works... i need to now if this object can take a wired lan replicate it in 3 ports and expand the wireless network of my router.
View 5 Replies
View Related
Aug 20, 2011
I went out and bought a e4200 today and the signal strength is worse than my WGT300n, is there any tweaks I can do to expand my signal strength?
View 3 Replies
View Related
Jan 26, 2011
i want to know how to set up a local area network
View 3 Replies
View Related
Jan 10, 2012
how I can setup a WAN. there is a central branch of our company and there are some other offices I want to connect them.
View 3 Replies
View Related
May 21, 2012
Ok so my dell Inspron desktop has had many internet related issues before, but this time it can't find the local area connection. I have taken the Ethernet cord and plugged it into the laptop im posting on and it works just fine so it is a problem with the computer.
View 7 Replies
View Related
Sep 1, 2012
I have just recently installed a new router for my home and the ethernet connection stopped showing up. It instead said "no connections available". I figured the onboard network adapter gave out because of the orange light it gave off and bought a NetGear GA311 network adapter. I installed it and updated it, but the connection still says there are none available.
View 7 Replies
View Related
Oct 26, 2012
We have a WIRED network and a WIRELESS network at work. I start downloading a big file over the wireless network. I realize that it is slow, half way thru the processs there any way, I can set up the network, such that, DURING the file transfer process, I can switch from wireless to wired, without any disruption?...
View 5 Replies
View Related
Jul 31, 2011
I have a wired and wireless network setup at home with 2 PCs wired and 2 PCs using wireless via a Fritz!Box 7390. The 2 wireless PCs are a Media Centre PC connected to the TV and the other is my young sons PC. I have an old switch (10Mbs) that I would like to connect to the Ethernet port of the Media Centre PC and then run Cat5 to 2 Topfield PVRs so they can access the internet for updates.I know I have setup a bridge between the wireless connection and the wired but not totally sure what to do and how to get the switch setup.The Media Centre PC is running Windows 7 Home Premium SP1 and has a Belkin USB wireless tongle.
View 8 Replies
View Related
