In the note, i ve seen we can configure a WDS with 2 WRVS4400N, but i can't.How can i configure the 2nd WRVS4400N as repeater? Or can i configure it as Access point for another modem ?
View 1 RepliesMy WRVS4400N rebooted itself and went back to default settings; it was set for a 10.x.x.x network, and is now back to 192.x.x.x network. How do I configure it back to the 10.x.x.x network?
View 4 Replies View RelatedI'll just use the 4400n to provide DHCP to my two VLANs and then a new problem cropped up. I am unable to add a default route to the 4400n's DHCP server. It uses the 4400n's vlan IP as the default route. What I'm trying to ultimately achieve is to configure the 4400n as an access point for our "private" network on vlan1 and also "guest" access to the internet on vlan2.
View 12 Replies View RelatedI live in a house of about 30 tenants. The place uses a cisco WRVS4400N router. It seems that my computer gets assigned a temporary ip automatically and then there will be times when I get "kicked out" and my computer doesn't get connected to the internet. Sometimes for few minutes and sometimes for hours.
No idea what happens there but could be that there are no ips left to assign to my computer and someone else gets the ip address.Anyway I'm trying to find out if I can configure my computer with a static ip.
The maximum number of dhcp users was changed from 50 to 100 by me. IDK if that means that I can assign a static ip from 1 to 100 but say I pick a number 160 so the ip would be xxx.xxx.x.160.
1. What are the steps I have to undertake to configure my computer on the router page? What info. do I have to modify?
2. After I modify settings on the router page, do I have to change settings on my computer?
I hardly try to get WDS running with two WRVS4400N v2.The manual (and the web interface) says: "Note: The WDS feature allows WRVS4400N to connect with up to 3 wireless repeaters that can be either WRVS4400N or WAP200." But I wasn't successful by now in getting it working..What I've done so far:
- Setup the primary WRVS as Gateway, WAN through Modem, LAN and WLAN using WPA2 Personal Mixed, DHCP
- works perfect
- Setup the second WRVS as Router using the same WLAN settings, no WAN and no DHCP
- Enabling WDS on both WRVS, giving each the MAC address of the other
- no connection to LAN or WAN through the second WRVS
I really need the second WRVS act like a bridge. Since the manual is saying that I can connect both devices through WDS I bought two of them. On the other hand I've now read somewhere in the community, that this isn't possible with two WRVS (?)
I've got an out of the box WRVS4400N and it will not pick up a DHCP IP from the ISP.
I reset to factory defaults, tried another ISP, returned and got a second wrvs4400n all the same results - no IP address on the WAN port. The internet LEDs are blinking but no IP on WAN port and no internet connection from a laptop connected to wrvs4400n.
I even tried turning of the firewall too.
Is there something with these routers that needs to be done for internet access?
Most typical small routers are just set up as a DHCP client on the WAN side and DHCP server on the LAN side.
I am using a WRVS4400N as my primary router for a small office. I get the following message repeated over and over in my logs. This seems to happen for 2 or 3 days and then it will go away for about a week and then come back. What is causing this? The best I can tell I don't have any IP conflicts on the network and most of the time the network has very little traffic other than 2 or 3 computers surfing the web. [code]
View 19 Replies View RelatedI am having some problems with WRVS4400N v2.We use it just for wired network (wireless is not in use, but it is configured). As a WAN we use PPPoE. Most machines do not use DHCP.After a while (few hours to few days after power up) the router freezes and it is not accessible. I cannot ping it or access to the admin page.I have the latest firmware version (V1.00.09-ETSI)I also called service and they suggested to reset it to factory settings and reconfigure it.
View 3 Replies View RelatedIk have a 50MB/s internet connection and my IPS provider's modem out is indeen 50MB/s
Per port from my router i do not get more than 20 to 23 MB/s ou tof it.
I have an older Linksys WRVS4400N Version 1.1 VPN Router. I have it set to run in mixed mode G/N. I still can only get connection speeds of 54 Mbps though. How can I get my wireless N clients to see 300 Mbps speeds?
View 1 Replies View RelatedI have a D-Link DSL-320B ADSL2+ Ethernet modem that connects to the internet fine if I am using just 1 computer. However I have bought a Cisco WRVS4400N to enable me to get all of the other computers at home on the network (wired and wireless).
The WRVS4400N picks up a WAN address from the D-Link BUT I just cannot get an internet connection, just "Local" only. I have tried setting it up as a gateway, as a router, upgraded the firmware but it just is not having it. My previous experience with routers has been just to plug em in and let them get on with it. The WRVS4400N is proving very troublesome.
I am have a lot of difficulty getting my WET610N to connect to my WRVS4400N. I have tried almost everything. I have some older PC's, as well as my PS3, that we use to use on the network and they only connect B/G. I have tried auto DHCP and static IP on the bridge. It seems that the only way that the bridge works is by using the WPS function that the business class routers do not have.
View 1 Replies View RelatedNow that Comcast is in the process of rolling out IPv^ to their customers nationwide, will there be a firmware update that properly displays the IPv6 /64 address as provided by the cable provider? Currently the only IPv6 address displayed is on the LAN page and is not configurable (greyed out) except for the prefix length. I already have a cable modem that will provide both IPv4 and IPv6 addresses as they are rolled out.
Currently running WRVS4400N v2 fw 2.0.2.1
I wonder if there is any place in WRVS4400N where I can tell it to just be an Accesspoint?
I have a customer who have 8 sites and we don´t know if there is enough with one wireless router or if we need some AP as well.
If it´s possible to make the WRVS4400N to become an WAP4410N then we can by only one machine no matter what...
I have installed a WRVS4400N router in a client's office. When laptops are plugged into the router everything works fine. When they are attached via the wireless signal it drops frequently. WPA personal is being used to encrypt. I have also installed the latest firmware and am having the same results. What can be done to eliminate the drops?
View 10 Replies View RelatedI have an ongoing problem with my WRVS4400N router. It reboots on it's own when streaming video through a wireless connection (computer, xbox, roku, tv). Once I make a wired conection, it performs flawlessly. The firmware is up to date. I have read some reviews of this router on Amazon stating the same problem, but I expected it to be solved with firmware update. Unfortunately, this was not the case.
View 4 Replies View RelatedI need trouble-shooting wireless network connectivity issues that arose recently:We use a Comcast modem and two WRVS4400N's as wireless routers/wireless access points.We recently got our comcast service upgraded to 100/20 and also got rid of our static ip address. As a result (I think there must be a sort of causal relationship here, but I'm not sure what it is) we can no longer connect to the internet using our wireless networks. We can connect to the wireless network, but have "No Internet Access."
View 4 Replies View RelatedAll of my remote sites use various routers to route all of their traffic via IPsec. However, I have one WRVS4400N w/firmware 2.0.2.1 configured with a working tunnel. My issue is I need to set the Remote Group to 0.0.0.0 0.0.0.0 so all traffic is forced via IPsec tunnel and not out the local gateway. When I do the error, Remote Security Group and Local Security Group cannot be in the same network. However, it works with Cisco/Linksys RV042.
View 3 Replies View RelatedI've been searching high and low and although I've found many results of people having this same exact problem there doesn't seem to be a fix, or at least no one was kind enough to post one. I have many vlans but the 3 in question are 10, 20, 30.
-10 is for my laptops and desktops with an ip range of 192.168.10.10 - 192.168.10.50.
-20 is my home automation network with an orange of 192.168.20.20 - 192.168.20.150
-30 is my guest network with a orange of 192.168.30.84 - 192.168.30.89
I have a dell powerconnect configured with vlans as my core switch. I trunked a port on the switch assigning 3 vlans (10,20,30) and connected it to port 1 on the wrvs4400N. On the wrvs4400 I trunked port 1 tagging vlan 10,20,30. For some reason vlan 1 is untagged on port 1 and I don't know why. I also have a router connected to the powerconnect. Of the 3 vlans I mentioned vlan 10 and vlan 30 are the only ones with interfaces on the router. Vlan 20 is an internal network with a separate router and until I figure this out that router is physically turned off. Also the router currently turned on has no routes configured to connect my vlans. Currently there is no configured way to jump vlans.
No matter what ssid I connect to I get a dhcp response from vlan 10. all my test indicates that I'm actually on vlan 10. I get internet and I can hit all devices on vlan 10. If I connect to ssid guest and change my ip address to match vlan 30 I can not ping the gateway for vlan 30 and I have no internet access. Some times I get something different. Sometimes I get an ip address from vlan 1 on the powerconnect. If I renew my ip address then I'll grab one from vlan 10 but I should be getting one from 30 or none at all for vlan 20. The absolute crazy part is my droid sometimes gets a 192.168.4.x ip address. I don't have a 192.168.4.x network or dhcp scope anywhere on my network! If I physically plug into a port on the power connect I get to the correct network 10 out of 10 times. If I configure vlans on the other 3 ports on the wrvs4400 and physically plug in, I get to the correct network 10 out of 10 times. I've reset to factory a few times and I've been all inside and out of the wrvs4400. I have no clue what could be wrong with this thing.
I have setup a ISA2006 as Internet firewall, and use 4400N as VPN Client, connect to ISA2006 via IPSec VPN, but it did not work.
Network topological as below:
Internet <------------> ISA2006 <-------------------------> local1 <------------>local2 <--------------------> WRVS4400N <----------> PC
Static Internet IP | 192.168.112.25 192.168.112.0/255 | 192.168.114.0/255
[Code]......
WRVS4400N v2.0 2.0.0.8
QuickVPN 1.4.1.2
Vista Home Premium SP2 64-bit
Trying to connect from laptop through an AP to my WRVS4400N via VPN. Not having much luck...I get to "Activating Policy..." and then "Connection Error".I like this router thus far, I have been able to set up multiple BSSIDs and VLANs which has been very useful.
I have several wired and wireless devices connected to the router which is running the latest firmware (2.0.2.1) and I have this issue with all wireless devices. The router is configured for B/G/N Mixed, Channel 6, and to broadcast the SSID. Security Mode is WPA2-Personal w/ key renewal set to 3600. Connection control is configured to allow only the desired MAC addresses. All wireless clients are configured for DHCP (as are some of the wired clients that do not have this issue). I have tried various setting changes over time, none of which have resolved the issue.
What I have determined, and may be useful, is that each time this occurs I am unable to ping the router from the client and have no connectivity to the internet or other devices on the network. If I ping the WAP address (reserved for internal use address) I get a response and then connectivity is always restored after doing so. In other words, I ping 192.168.1.1 and get no response, immediately ping 192.168.1.2 and get a response, then immediately ping 192.168.1.1 and now get a response and connectivity is restored. If I skip the first step and just ping the reserved address followed by the router address result is always the same. It would appear the issue is between the the two router addresses.
Prior to owning this router I had a Linksys BEFSX41 that I had for about 7-8 years and a WAP54G I had for about 5, both of which still worked and I never had this issue with my wireless clients. I went to this router for the increased performance and am very happy with that aspect, however this issue is unacceptable.
We have an office with about 10 PCs, and several other network devices (smartphones, printers, etc). Some PCs and printers are wired, some are not. About two weeks ago, some (6) of the wireless devices lost connectivity. Since then, some (4) of the devices have also recovered normal connectivity.
As of right now, there are two computers, a laptop and a desktop, that cannot use the wireless network. They see the wireless network, connect to it, receive an IP via DHCP properly, have correct DNS servers listed in ipconfig, but they can't ping the router, use the intranet, or internet.
I have a WRVS4400N that broadcasts two different SSIDs. One is a public network and the second is a private network. Right now, both SSIDs are pulling from the same DHCP server, but I would like to separate the public from the private. How can I separate these SSIDs by vlans? I can't seem to get the vlans to route to separate ports.
This is my vlan settings. I have two DHCP servers right now. One is in an isolated network plugged into Port 3 of the WRVS4400N. The other is on the production network, plugged into port 1 of the WRVS4400N. For some reason, whenever I connect to SSID Public, it won't pull an IP from the DHCP on port 1, it only pulls it from the one on port 2.
I know there is three SSIDs here, the Static one is going to be the same network as the EMS one.
I just purchased a Toshiba Thrive tablet and I can't get it to connect to my wireless router. My router (WRVS4400N) works flawlessly with my laptop and desktop. I have spoken to a Cisco tech rep and they assured me that there is not a compatibility problem with the WPA-Personal setting I am using. When I speak to a Toshiba tech they tell me I have a router conflict. To verify this I went to my local Starbucks and low and behold it logged right on with no problem (The Starbucks system was not a protected system). This confirms to me that there is a conflict between the router and the tablet.Toshiba tells me that it is not compliant with Android but it is with Windows that is why I don't have an issue with the computers.
View 2 Replies View RelatedI just purchased a WRVS4400N Wireless-N Gigabit Security Router - VPN V2.0 and seem not to work with PPPoE from bluewin.ch ( Swisscom )
View 2 Replies View RelatedI just purchased the Cisco Small Business Wireless-N Gigabit Security Router with VPN (WRVS4400N). I'm moving overseas (to Israel) and noticed that the power supply does not go up to 240V. I then called the Cisco Customer Support and they told me that they don't have another power supply. Although they mentioned that I could probably get the unit in the country I'm going where it would already have the right power supply. Now, what I'm wonder, should I just send this back and figure it out when I get there? Or bring it with the hope of finding the right power supply?
View 1 Replies View RelatedI have a WRVS4400N v2 acting as a gateway connected to a cable modem and am interested in extending it's range by placing a WAP4410N elsewhere in the building to cover a deadspot. Is there a mode on the WAP to best achieve this (e.g., wireless repeater, bridge, etc.)? I had assumed that it would be the wireless client/repeater mode, but the thread below leads me to believe otherwise, but is not labeled as resolved.
[URL]
As a different approach, could I extend the range of the original gateway WRVS4400N by dropping a second WRVS4400N in the deadspot and setting it to router mode? Language in the WRVS4400N v2 administrator screens lead me to believe that I could try this but I am unclear as to whether it would work wirelessly or need to be connected to the gateway via an ethernet cable, which is what I am trying to avoid.
I buy a WRVS4400N router on amazon.fr because on cisco.com, the Product Specifications say "Dual-stack IPv4 and IPv6" [URL]
The ipv6 work for the local network. But the router does'nt fetch my IPv6 take by my ISP (by PPPoE) How do I get IPv6?
I have 2 WRVS4400N's availible to be. One is running my network and security connected to my WAN.I want to use the other one stricly as a switch or even adding wireless repeat of my current wireless LAN.
View 1 Replies View RelatedI'm keep failing my pci compliance test I have a wrvs4400n and I keep getting "firewall udp packet source port 53 ruleset bypass" i've blocked port 53 but keep getting rejected. How to set the router?
View 1 Replies View RelatedI would like to connect to the built in accounts on the wrvs4400n from a mac VPN client. I am new VPN and have not found much information on how to establish this connection. Since Linksys seems determined to rely on Quickvpn, and provides no information on what it is actually doing under the hood I can not figure out how to configure any of the VPN clients available, or the built in VPN tools, for OS X (10.4.8). The only information I have been able to find seems to relate to setting up VPN Tunnels, or running a server behind the wrvs4400n and using one of the VPN passthrough options. I would like to connect directly to the built in accounts, how to set this up on a mac?
View 7 Replies View RelatedI am attempting to setup a router with another vendor, but I am not wanting to give full access to the network just a couple IP addresses, most routers you can setup an VPN IP Range, but I can't find that setting on this Cisco WRVS4400N.
View 1 Replies View Related