Cisco Wireless :: Wirelessly Extend Range Of WRVS4400N?
Oct 31, 2009
I have a WRVS4400N v2 acting as a gateway connected to a cable modem and am interested in extending it's range by placing a WAP4410N elsewhere in the building to cover a deadspot. Is there a mode on the WAP to best achieve this (e.g., wireless repeater, bridge, etc.)? I had assumed that it would be the wireless client/repeater mode, but the thread below leads me to believe otherwise, but is not labeled as resolved.
[URL]
As a different approach, could I extend the range of the original gateway WRVS4400N by dropping a second WRVS4400N in the deadspot and setting it to router mode? Language in the WRVS4400N v2 administrator screens lead me to believe that I could try this but I am unclear as to whether it would work wirelessly or need to be connected to the gateway via an ethernet cable, which is what I am trying to avoid.
View 7 Replies
ADVERTISEMENT
Jul 23, 2012
I have a BT home hub 2.0A (BT is our ISP) it covers most of our house except for my bedroom. I have two spare routers i'm not using, one is a Speedtouch ST585 v6 and the other is a Belkin F5D7632-4 and was wondering if I could use these to extend the range of the home hub wirelessly. As far as I can tell I cannot install dd-wrt on any of these 3.
View 2 Replies
View Related
Oct 27, 2011
I have a couple of computers that are out of range of my router so I came up with a unique solution. I have an old laptop with 2 wireless cards that I put halfway between. It is working but I have a few oddities. First of all, the out of range computer is connected to another wireless router that several laptops and another (wired) PC connect to. It has ICS (Windows XP internet connect sharing) enabled. This rules out using ICS on the laptop as 2 pc's would have the address of 192.168.0.1.
View 1 Replies
View Related
Jan 20, 2012
I'm trying to extend the range of my wireless network from my house to my workshop, which is about 600 feet away. There are no trees or other objects in between the two buildings. how I could boost my wireless signal to reach that far?
View 1 Replies
View Related
Jun 4, 2010
I get 10% signal in my bedroom using WEP2 and I would like to boost this to at least 50%
1) I have 2 DIR-655 Wireless N routers, both functional.
2) The first router is on the other side of the house from my room
3) The second router is not in use at all ... I'd like to take advantage of it
4) I have an Ethernet drop in my bedroom that runs under the house to the first router. I have a switch on that drop and use it for my Sony / Netflix box ...
I have been told that the DIR-655 cannot be used as a repeater. Can I not take advantage of the 2nd router to boost my signal in any way?
View 9 Replies
View Related
Dec 7, 2012
how do i extend wireless range and increase signal to granny flat for internet? from the modem to the granny flat about 15m+, i tested it with my laptop get 3 green signal and on inSSID get around 74+ RSSI but with Asus-n13 and mini Tp Link wireless USB adapter get above 79-80 RSSI. don't know why but i get signal for surfing internet on laptop but randomly get drop out. household gave me $200 to improve the signal....
View 4 Replies
View Related
Aug 6, 2012
I am trying to use the Netgear WNR 2000 V3's repeater function to wirelessly extend the range of a Linksys WRT54GX V.2. I have the SSID's and channels the same. I had the Netgear working great as an extender with my Apple Airport Extreme base station (equipped with WDS). As far as I know, the Linksys is not equipped with WDS.
View 4 Replies
View Related
May 15, 2011
I have two Dir-655's - router1 and router2.
Router1:
ip 192.168.0.1
subnet 255.255.255.0
DHCP enabled range = 192.168.0.100 to 192.168.0.200
Router 2:
ip 192.168.0.2
subnet 255.255.255.0
DHCP disabled
Routers are connected to each other via LAN ports with a switch in between.Both routers have the same wireless SSID with the same password. I am able to connect wirelessly to both routers no problem.
I have a machine running a shared iTunes library which has a wired connection to router1. I also have an Apple TV wired to router2. My issue is if I am connected wirelessly to router2 I may or may not be able to connect to iTunes library. Conversely, if I am connected wirelessly to router1 I may or may not be able to play content from iTunes to Apple TV. I cannot figure out why everything works fine sometimes yet at other times I cannot connect devices between the two routers.
View 3 Replies
View Related
Mar 25, 2011
i have intermittent connectivity on the 2nd router that was installed on the network in order to extend range. 2nd router is connected to the original wireless router by an ethernet cable.
View 5 Replies
View Related
Jul 26, 2011
Just purchased WRT54GL for family friend to extend the wireless range of their DSL via 2Wire ATT modem Wireless router. One desktop computer will stay wired to the 2Wire and laptop or 2 will connect to the WRT54GL since the 2Wire cannot reach into the yard (metal buiding). I've seen several examples of connecting two WRT54G together. I Can I do that well with std Linksys software or would I be better off downloading Tomato or DD-WRT third party?
View 1 Replies
View Related
Nov 1, 2012
I have a 3 story townhouse and want to have one n600 connected to my modem on the 3rd floor and then have the other downstairs connected through wireless to the one upstairs. I have seen lyncsys will do this but will the belkins?
View 1 Replies
View Related
Feb 22, 2011
I have a WRP400 connected to the internet, and have a WAG160N that I no longer use and would like to to extend my wireless range.I connected them via an Ethernet cable and it seems to work fine without configuring the WAG160N (seemed to just work automatically), but I can't access the WAG160N admin GUI (tried all sorts of IPs in the WRP400 range) to change any settings (frustrating). My guess is that it's probably not the best way to set it up.
1. Set the IP of the WAG160N (The WRP400 is set to 192.168.15.1, so should I change the WAG160N to 192.168.15.2. Or should I be setting it within the WRP400's DHCP range which starts at 192.168.15.100?)
2. Swtich off the DHCP on the WAG160N. (I think I tried this late last night and it wouldn't assign an IP to my laptop, unless I did somehting wrong)
3. Connect the two using a ethernet cable.
After I do this I should still be able to access the WAG160N's admin GUI with the IP assigned in step 1?
View 3 Replies
View Related
Aug 15, 2012
I would like to know what to buy to extend the range of my wireless network , which will not reach throughout my house.
Also, I would like to know what the button is for on the front of of the router, since it is not a WPS button, according to ATT.
View 4 Replies
View Related
Dec 27, 2010
I have the WRT610N, and I was wondering if there is a way to repeat the 5GHz network to extend the range.I am trying to stream content from a Blu-Ray player, and while the 2.4GHz network reaches, the signal is very weak. The 5GHz network doesn't reach, but I would prefer to stream content through that network than the 2.4GHz.
View 7 Replies
View Related
Dec 10, 2012
We own two houses next door to each other and I have the first 655 set up as WAP, wired to second in other house as a range extender. Works perfectly. I would like to add a third 655 (wired to the second) to extend my range further.
View 5 Replies
View Related
Apr 25, 2011
How do I extend my wifi network?I have a Dlink DIR 615....
View 5 Replies
View Related
Jan 9, 2013
I have a Belkin F6D4230-4 Enhanced N150 router. Would it be advisable to add a range extender to hit weak signal areas or simply upgrade to a more powerful router?
View 1 Replies
View Related
Aug 9, 2012
Our wireless router is in a room at one end of the house (beside the telephone point) from which ethernet cables can connect to the Cat5 sockets taking the broadband to the other rooms that have a Cat5 socket. That is fine for connecting devices to the sockets in the other rooms but because the house is old with thick walls our wifi signal fades to nothing in some parts of the house. Moving the wireless router only moves the problem to another area. I thought about a wifi repeater but the room I would like to locate it in to then boost the signal to the rest of the house is borderline on the range for the wireless router. Is it possible to connect another wireless router or device to the main wireless router through the Cat5 cabling so that the second router/device can offer wifi to that area of the house?
View 3 Replies
View Related
Mar 9, 2012
i having balkin f7d1401 how can i extend wifi range .
View 3 Replies
View Related
Feb 4, 2013
I have a WAG354G that i would like to use to extend the range of my WiFi. First Question is - is it possible, and the second is how do i do it?
View 3 Replies
View Related
Feb 10, 2013
I am having problem using the N300 dual-Ban Wi-Fi Range extender with my att 2wire 3800HGV-B router. Cannot use the extender to access the internet. The Att router works without it. Just want to use the extender to extend my att router signal but cannot.
View 3 Replies
View Related
May 28, 2011
I recently configured a linksys range extender to my modem and since doing that, I'm getting a message stating that there is an IP address conflict with another system on the network. When I set up the range extender, I assigned an IP address to it that was different from the modem but yet this message still appears. Also even though my wireless connection is connected, I'm unable to connect to the internet - I keep getting the message 'internet explorer cannot display webpage'.
View 3 Replies
View Related
Jan 13, 2012
My b/g/n router is at one end of the house and on the second floor needs to be. I currently have a b/g/n wireless bridge hooked to a LAN port of an b/g/n router that I am using as an access point almost in the center of the house, about thirty feet away with one wall between them. I get good connection speed on an Internet TV that's about 7 feet below the access point with one floor/ceiling between. I get a reliable but slow connection to an Internet TV that is about 20 feet from the access point with two walls between. I get intermittent, slow connections with portable devices near the opposite end of the house on the first floor. Measured horizontally, they are within 15 feet of the upstairs TV that has a slow connection and about 9 feet below it.
The ceiling of my unfinished basement stairwell is a few feet below my router. I am thinking of putting a wireless bridge in the stairwell and connecting it with ethernet cable to an access point located in the crawl space, which is very dry, under the house directly below the upstairs Internet TV. It would be about 12 feet below the TV with a floor and a ceiling/floor between. That location would put it within 15 feet of the wireless devices on the far end of the house that now have a poor connection, with only a floor between. My primary goal is to get a better connection for them, but I'm hoping for a better one to the upstairs TV. My house is of frame construction with mostly plaster interior walls.
I want to use a POE access point under the house because I think it would be easier and safer than running a long extension cord. Looking at POE devices in catalogs, it is often not clear to me whether the device in question expects to be powered over ethernet or expects to power other devices over ethernet.
I have the following questions:
Does my plan sound feasible, and would it be expected to accomplish what I want?
How can I be sure that, when I order a POE access point, it expects to receive power over ethernet, not provide it?
Can POE devices be cascaded? If I do this and find that I did not get the coverage I hoped and, therefore, want to add another POE AP, can I add a POE hub or switch and run cable from it to the additional POE AP? If so, is there any particular monclature for devices that expect to both receive and provide POE? Can such devices receive and provide over any port, or do they have to receive power on a designated one and provide it to the others?
View 3 Replies
View Related
Oct 18, 2012
I would like to configure 3 Access Point (WAP4410N) to extend the wifi in my house. I try it to do several configuration but it doesn't work.
In this configuration, the wifi devices disappears and re-appears constantly. I lose the IP addresses and they all come down only every 5 seconds. I made screen shots of the 3 terminals in the word document attached below
View 2 Replies
View Related
Feb 15, 2012
i have following requirement.Wired part of the network is already done.
CiSCO 2800 or 800 router connected to ethernet switch and pcs connected.i want another 5 pcs connect to this LAN through wireless connection distance between wired part and this new location is approximateley 200meters. how can i do this using access points and repeters or any other methods?
View 7 Replies
View Related
Jan 21, 2013
Ground floor: My ISP's wireless router and an 8-port switch. For wireless communication I use the ISP's Wifi and the 8-port switch is used for wired rj45 sockets around the house.
1st Floor: I have a TP-LINK TL-WR740N Wireless Lite N Router 150 MBps which I connected to a socket and have a PC connect with wire on it and also used for Wifi. The Wifi network I setup on the 1st floor is different than the one on the ground floor (2 routers).
At the first floor I have the problem that in other bedrooms far from the router the Wifi signal (either gets lost) or it's very low. So I bought a TP-LINK TL-WA701ND Wireless N Access Point 150MBps which I configured as universal repeater.
The access point supports only WEP encryption when used as repeater/universal repeater so I changed the wifi of the router to WEP with ASCII with 128bit character length and established the connection.The most important now is that even though the Wifi signal in the bedroom with the AP is full, when I switch off the wifi of the iPad and back on, it is not connecting to the internet. Yesterday I noticed that it was giving me the ethernet card IP (169.…). I went close to the router with the iPhone, got connected and when came back to the room with the AP it was working but the iPad is not working.
View 2 Replies
View Related
Jun 9, 2012
I have an 802.11n/g wireless network throughout my house. I also have several ethernet ports. I want to use the ethernet port to connect to the network and extended the existing wireless network (same SSID). I know AirPort devices from Apple can do this but I wanted to know if anything else could as well. It is too slow when I try to wirelessly extend it (not using ethernet at all).
View 4 Replies
View Related
Jan 17, 2011
Just recently got a new 881W router. i have downloaded the 2.4 software upgrade. I go into the Office extend AP login and i get just a enter button. when i click on the enter button the AP page does not come up.
View 7 Replies
View Related
Jul 6, 2010
I have finally got my office extend AP to connect to my companies 5508 controller by enabling NAT on the management interface and can see all the cooperate SSID's. However when I try to connect to the SSID my client either gets a local IP address from my home router or then cannot get any IP address.
View 9 Replies
View Related
Feb 27, 2013
I'm trying to configure a WAP321 so that I have the same SSID and WPA2 password on both the RV220W and the WAP321 so that i can reach all areas of my clients location.
View 1 Replies
View Related
Jan 21, 2013
I have two 1130 AGs and would like to have one connected to a wired net with wireless clients on the G radio, and connected to the other using the A radio, and it having clients on it G radio.
View 1 Replies
View Related
Jun 3, 2013
We are looking for a solution to bridge two locations. 1300 and 1400 are now eol and we have found that Cisco now offers Exalt ExtendAir r5005 product for this purpose.
However we were unable to find a P/N for SmartNET for this device. Is there any such P/N?
View 3 Replies
View Related
Aug 10, 2010
set up the wireless network at a friend's house, which is a large solid-brick house that winds from one end to the other. The current location of where the cable comes into the house is unfortunately on the far-left end of the house, which means that the right end of the house receives no signal from their DIR-825 wireless N router.
What I've been looking into is the best way to wirelessly extend the wireless signal to the other end of the house. It seems straightforward enough to use an ethernet cable and access point to extend a wireless network, but that is not really a good option for this house. After reading many forum posts (and not being an expert myself) it seems like it may be possible to wirelessly extend the wireless network with another router, although it appeared that this is much less common (if at all possible) with wireless N routers.
what device I need to accomplish what I've described above? Another router, or some kind of access point/bridge? I saw at least one rather expensive wireless N repeater online (a Hawking brand, I believe) but was hoping to avoid that option initially, but if that is the only way to go then so be it :-)
View 12 Replies
View Related
