I am unable to generate bug summary report in RME. Even I can not generate PSIRT report as well..LMS always gives error "incorrect cisco.com credential. enter correct credential" I have checked my credentials are correct... it gives me error no BTKT:0014..I am using LMS 3.1 attaaching snap shot of my patch level and application version running on LMS...
View 3 RepliesI am trying to generate bug summary report from RME but once job completes i can not see/view report. whenever I am trying to click on view under job result to see reports I get apache/http error. snap shot is attached for reference.
I am running LMS 3.2.1 and RME 4.3.2.. struggle alot to reach this stage where I can see report are getting generated for PSIRT and bug summary..but can not see report for Bugs though I can see PSIRT report...
I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.
View 4 Replies View RelatedI am running CiscoWorks LMS 4.0.1 since 6 months and I wanted to generate today a report about the interface utilization on 2 Cisco switches (Catalyst 3750G). The corresponding job is created, it runs and then i get "succeeded with info" in the "Run Status" column. When I want to click then on the "View Report" link, I get the following error: "Could not generate the report. Either data is not available for the specified duration or the report job failed."
I tried the same procedure with 2 other switches but I have got the same result.
How to generate a Report for all ur existence Subnet's using LMS 4.2?
View 2 Replies View RelatedI have a WCS server running the version 6.0.170.0. I have already added few WLCs running the version 7.0 to this WCS. It is working fine. And now I have added two new controllers running the version 7.0.98.0 to the existing WCS server. When i add the floor layouts to the WCS and position the access points from the new controllers, the heat map is not generated automatically.
View 2 Replies View RelatedI just find there is no "Crypto key generate" command line in my Catalyst4506-E with cat4500e-universal.SPA.03.01.01.SG.150-1.XO1.bin image. Is there any other command I can use to enable ssh access? this command is always able to use on other catalyst switch like 3750X.
View 4 Replies View RelatedUnable to run Eos/EoL report, I get error that my cisco.com credential are not valid, I verified my credential and they work fine. I'm running RME4.3.2 on Solaris 10.
View 3 Replies View RelatedLMS 4.21
Solaris 10
Trying to schedule a Best Practices Network Discrepancy Report everything works find (reports could be scheduled) except entering a eMail-Address in Textfield: E-mail.
Hitting the Submit Button results in nothing, no popup stating the created job ID; without any content in this field a job is able to be scheduled.
When you configure an ABR to inject a summary route into an area, what are the circumstances under which the ABR will inject the summary? I.e., since it's not a set of specific subnets learned directly from other OSPF routers, does the summary get injected regardless of what's in the routing table of the ABR?
I would imagine this could cause problems in a situation where there is an ABR injecting a large summary into an NSSA that also has a backup path over the Internet (IPsec tunnel or something). For example, if the area 0 routers from which the ABR receives routes went down, the ABR would continue to inject the summary route into the NSSA thus tricking those routers into sending traffic to the ABR rather than over the backup link.
I can't imagine any other way an ABR would decide when it's suitable to inject the summary though.
I have two MLS conected by 2 fast ethernet links f0/11 and f0/12 on both sides.I am trying to set up a layer 3 etherchannel using these two links . But when i see etherchannel summary, they dont show up as layer 3. Instead they show as layer 2.
View 19 Replies View RelatedI have setup a site to site VPN with an ASA 5510 (8.4) and a Cisco 2811. The tunnel is working fine, however both sites have 5 different contiguous networks. The crypto ACL between sites states only one subnet.Is it possible to state a summary address in an ACL rather than having five lines for the ACL?The tunnel works when the router uses an ACL of 10.2.200.0 0.0.7.255, however if a summary address of all the subnets on the inside network of the ASA are stated in an ACL - 10.1.200.0 255.255.248.0 - then the tunnel does not come up.Is it possible to state a summary address on a crypto ACL on the ASA?
View 2 Replies View RelatedIn my Lab environment in GNS I have connected two 7200 series router through fastethernet on router A I have given IP adress 192.168.10.54 and router B I have given IP address 192.168.10.53 and default route as 0.0.0.0 0.0.0.0 192.168.10.53 and when I run the command on router A it shows result as follows "C 192.168.10.52/24 is directly connected ,Fast ethernet 2/0".
So I need to know why it's showing the result of .52 at last why not .53 or .54 at last what is the reason it's showing .52 which I have not mentioned in my IP address.
I have a 5508 WLC running on 7.0.116, I need to be able to pull all configured users off the WLC and import into excel, I have 900 odd users configured. When I run a show net user summary it only displays a third of users. I'm hitting space to tab through each page, then eventually I just get dumped back to the command prompt.
View 5 Replies View RelatedI have a Nexus 7K router, has 2 ospf process, ospf 1 and ospf2. OSPF1 has several subnets in 10.1.0.0/16 subnet range , OSPF2 has several subnets in 10.2.0.0/16 subnet range. I want to summary OSPF 1 subnets to 10.1.0.0/16 then redistribute to OSPF2. but it doesn't work. [code]
View 2 Replies View RelatedAnyn equivalent command of show etherchannel summary for a 10008 router running 12.2(33)SB9 ?
View 1 Replies View RelatedWhat is the OID for the count of the APs connected (and Status UP) to a WLC 5508?
View 2 Replies View RelatedIn earlier versions of LMS it was possible to choose i.e. the Routers category (top level) and enter a series of commands to be excluded from the comparison. In LMS 4.0.1 I experience, in several different installations, that this is not possible. It seems I can enter one exclude command beyond the defaults per category, the rest is not applied even though the feedback from the application is positive. Next time I access the Exclude Commands view, the commands I entered are gone. Is this a change of behaviour or a bug?
View 2 Replies View RelatedI have a layer 3 switch with a bunch of SVIs all in the 192.168.x.0/24 range. I just want to advertise a 192.168.0.0/16 summary to the BGP neighbors. I can do this either by:
1) Redistributing connected into BGP and then using the 'aggregate-address' command to advertise the summary.
2) Specifying a network statement in the BGP config for every single SVI, then using the 'aggregate-address' command.
3) Create a static route to null0 (ip route 192.168.0.0 255.255.0.0 null0) and put 'network 192.168.0.0 mask 255.255.0.0' command in the BGP config.All three fulfill the same purpose of summarizing all the SVIs, but creating the static route is much cleaner in this case. It seems like the aggregate-address command is mostly intended for routers that are aggregating connections coming from other routers and all of them share a common prefix.
if I can do the following deployment using a Cisco ASA5510 security plus.
At this moment I have two interfaces in use one (outside) with the IP: 172.16.21.254/24 and the other (inside) with the IP: 192.168.4.1/24. Now the customer needs to connect another network that works with the IP segment: 192.168.0.0/22.
The IP segment 192.168.0.0/22 goes from 192.168.0.1 to 192.168.3.254 that means that there is no a overlap with the network segment 192.168.4.0/24. My question is: If I configure another interface in the ASA that works in the segment 192.168.0.0/22 the routing table will auto-summary the network and merge it with the network 192.168.4.0 or will it leave the networks apart??
I don't user dynamic routing protocols but I cannot do the changes if I have doubts because the network 192.168.0.0/22 is a the Network for the Factory Automation Systems.
My Cisco 3900 router is not taking the no auto summary command?
View 5 Replies View RelatedI have a Nexus 7K router, has 2 ospf process, ospf 1 and ospf2. OSPF1 has several subnets in 10.1.0.0/16 subnet range , OSPF2 has several subnets in 10.2.0.0/16 subnet range. I want to summary OSPF 1 subnets to 10.1.0.0/16 then redistribute to OSPF2.but OSPF 2 didn't receive 10.1.0.0/16. Below is the config
ip prefix-list all seq 10 permit 0.0.0.0/0 le 32
route-map all permit 10
match ip address prefix-list all
router ospf 1
router-id 10.10.3.9
[code]....
tell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
We are already having a True business ID certificate from Geotrust for our SSL VPN on CISCO ASA 5510.this is working fine.
We are now changing our device from ASA 5510 to ASA5520 in failover setup. As we check with Geotrust they are asking us to create a new CSR with same parameters from new ASA5520 device and reissue the certificate from their site.In this context how to create a new CSR from ASA5520 8.2(5). create CSR from ASA 5520 8.2(5)
I'm playing with ipv6 and trying to get a tunnel between two sites working (basically following this example url...
View 6 Replies View Relatedwe have a policy on ACS to disable user account (Internal user identify store) after X days if password is not changed. However, a few days before the password expires, there is no notification for users unless he happens to log in IOS router (tacacs) through console. in other words, if he logs into IOS devices through VTY, there is no notification at all.some users got locked out becuase they were not notified to change password. What setting on ACS 5.2 must be configured to display warning on VTY before password expires?
View 2 Replies View RelatedI have configured an Cisco 881 router in our lab with netflow commands and pointed to our network monitoring tool and I want to check if the tool can collect valid traffic statistics from this router (eg. utilization). The problem this router has nothing plugged into a production LAN that would potentially generate traffic to measure using this tool.
Is there a way to configure a Cisco router (ex. Cisco 881 router) to artificially generate network traffic to test that I have setup the monitoring tool correct to capture future utilization statistics?
ASA5510, Can't generate RSA keys, so can't SSH. [code]
View 2 Replies View Relateddo we have anything like universal password for cracking through wireless connection?
View 3 Replies View RelatedBasically i need to test to see where the telephone lines are terminated, because when they where built into the walls the used standard cat5e cable to terminate it to an RJ-11 jack but over in the wiring panel it (i assume it is anyways) terminates to an RJ-45 jack but im not sure if this is really the cable for the telephone or something else, so i have a phone connected to the wall jack and a computer on this end and i would like to send a dial tone or any tone in general that the phone can pickup.
View 3 Replies View RelatedI have a TP-Link Wireless Router (TL-WR340G) and I use it for both Wired and Wireless connection. I have two desktops that connects to the router through cables and I also have 2 notebooks that connects through WiFi.
Now, I want to know if there is any software that can generate passwords which I can assign into individual PCs that connects with Wifi. For example, Notebook #1 has the password "abcdefghij" and the Notebook #2 has the password "1234567890" and they can both connect to the WLAN.
We got a replacement ASA 5580 from Cisco. We were not aware of PAK, Is there any other possible to generate Activation key? Can we generate PAK or Activation Key using SO (service order) number?
View 1 Replies View RelatedI want to use IP SLA to perform simple up/down monitoring of an IP host and to generate a syslog alert if the host goes down. I have a 2650XM router running 12.4(23) IP Voice IOS. My basic IP SLA config is hown below:
ip sla monitor 10
type echo protocol ipIcmpEcho 10.55.1.1
timeout 1000
frequency 10
ip sla monitor schedule 10 life forever start-time now.