Cisco :: 2650 XM - Configure IP SLA To Generate Syslog Messages

May 19, 2010

I want to use IP SLA to perform simple up/down monitoring of an IP host and to generate a syslog alert if the host goes down. I have a 2650XM router running 12.4(23) IP Voice IOS. My basic IP SLA config is hown below:

ip sla monitor 10
type echo protocol ipIcmpEcho 10.55.1.1
timeout 1000
frequency 10
ip sla monitor schedule 10 life forever start-time now.

View 7 Replies


ADVERTISEMENT

Cisco AAA/Identity/Nac :: Configure ACS 5.2 To Send Syslog Messages To CS-MARS?

Dec 4, 2011

how can I configure ACS 5.2 to send syslog messages to CS-MARS?

View 3 Replies View Related

Cisco :: LMS 3.1 - RME Cannot Generate Syslog Report

May 17, 2011

I have an issue with rme 4.2 from LMS 3.1 When I try to generate a syslog report this shows me nothing. I locate SyslogCollector.log file and I see sometnig wrong.

View 4 Replies View Related

Cisco Firewall :: ASA 5520 - Syslog And Tacacs Generate Ping Response?

Mar 20, 2012

I'm trying to configure an ASA firewall (FW2) for syslog and tacacs and am experiencing strange behavior.  Both the syslog and ACS server are on the inside of another firewall (CoreFW).  Whenever a log message is generated on FW2 the request is dropped by CoreFW and message '%ASA-4-313004: Denied ICMP type=0, from laddr FW2 on interface outside-b2b to syslog01: no matching session' is displayed.  The same thing occurs for tacacs.
 
It appears that the syslog and ACS requests are generating ICMP echo replies, which the core firewall drops since no session exists on a lower security interface.  I have access lists configured on CoreFW to allow the syslog and tacacs requests.
 
FW2 is running asa825-k8.bin, CoreFW is asa824-k8.bin

View 1 Replies View Related

D-Link DIR-655 :: What Does Syslog Messages Mean

Jul 26, 2012

I'm getting the Syslog messages frequently on daily basis.

View 4 Replies View Related

Cisco :: LMS 4.2 Not Processing Syslog Messages

Mar 12, 2012

I have a new install of LMS 4.2 on a virtual appliance.  No syslog messages are getting into LMS.  They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.

View 3 Replies View Related

Cisco :: LMS 4.1 - No Syslog Messages Appearing?

Sep 28, 2011

LMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?

View 2 Replies View Related

Cisco :: LMS 4.0.1 Not Processing Syslog Messages

Jun 19, 2012

My Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?

View 2 Replies View Related

Cisco :: Syslog Messages Not Showing With LMS 4.1

Mar 3, 2013

I have a newly installed LMS 4.1 that had the Syslog feature working for a while.
 
Recently, the Syslog is no longer displaying any records (neither new or old messages).
 
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
 
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....

View 0 Replies View Related

Cisco :: LMS 3.2 - Invalid Syslog Messages

Aug 22, 2011

I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
 
Is there any posibility to get out from which devices those messages are?
 
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.

View 1 Replies View Related

Cisco :: Debug Syslog Messages In Router

Jun 26, 2012

Is there a way to debug syslog messages? Something like "debug ip syslog"?

View 11 Replies View Related

Cisco Switching/Routing :: Way To Get More Messages Out Of 2950 Set To Syslog

Feb 11, 2012

Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.

View 2 Replies View Related

Cisco Routers :: RV110W Excessive Syslog Messages?

Mar 6, 2012

I bought a RV110W wireless router a couple months ago that I've been pretty happy with.
 
However, I have one significant problem with it.  It is configured to send syslog messages to an internal server.  Twice now it has gone into a mode where it starts dumping messages like,
 
ip_conntrack_is_ipc_allowed: ipc_entry_is_full
 
continuously, at a rate of about 20 per second.  It otherwise seems to function normally, but of course if unnoticed my syslog file quickly grows to hundreds or thousands of megabytes.  A reboot restores normal operation.  It is running firmware 1.1.0.9.  A search on the internet turned up no information about this problem. 
 
It may be some corruption is occuring in the router's OS, or perhaps this is something that can be triggered externally (in which case it would be a weak form of DoS attack?  Or maybe worse if in this state it is unable to properly apply the firewall rules.)

View 2 Replies View Related

Cisco Firewall :: ASA 5520 Error Syslog Messages

May 10, 2012

We started getting the below syslog messages from one of our ASA5520 which was recently upgraded to 8.4(2). Any bugs on 8.4(2) that cause this or its simply the RAM failure?
 
%ASA-3-105010: (Primary) Failover message block alloc failed
%ASA-3-321007: System is low on free memory blocks of size 1550 (0 CNT out of 18709 MAX)

View 2 Replies View Related

Cisco :: Detecting Rogue AP Messages In Syslog And Configuring WLC 5500

May 7, 2013

I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior. I'm doing this step.
 
Authorize AP's against AAA function to make sure that  all the AP's registering to your WLC are authorized AP's of the  network.By  enabling this feature, only those AP's whose mac-addresses are present  in the authorization list, will be able to register to the URL
 
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it.URL
 
NOTE: from the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection"  mode sitting on the trunk port  on the switch then  only, this AP will detect the  Rogue on Wired
 
I don't think i completely understand this statement, by sitting does it mean that it is passively sniffing coming in/out on trunk link?
 
Considering the above steps are accurate, after this will i be able to see rogue detection behavior in syslogs? What exactly would be the messages that would produce this behavior.

View 7 Replies View Related

Cisco Switching/Routing :: 9500 Is It Possible To Change UDP Port For Syslog Messages

Jun 12, 2012

Is there any way to change the port that is used for syslog messages on a Cisco 9500 switch?By default this is set to UDP port 514.There doesn't seem to be a command to change the port.

View 1 Replies View Related

Cisco WAN :: 7600 / Syslog Doesn't Display Informational Level Messages

Mar 27, 2012

I have an issue with the syslog of 7600 router, I have configured the logging level to informational, but when I execute changes such as up or down an interface, the syslog messages aren't displayed? Why is the reason? This symptom exist after I changed the buffer size from default to 32768.
 
Router#sh log
Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 2 flushes, 0 overruns, xml disabled, filtering disabled)
 No Active Message Discriminator. 
No Inactive Message Discriminator.
Console logging: disabled
Monitor logging: level debugging, 40 messages logged, xml disabled,

[code]....

View 4 Replies View Related

Cisco Wireless :: 5500 Detecting Rogue AP Messages In Syslog / Configuring WLC

May 9, 2013

I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan  controller 5500 controller with AP (aironet 3500). I want to detect for  rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to  detect this behavior.
 
Authorize AP's against AAA function to make sure that  all the AP's  registering to your WLC are authorized AP's of the  network.By  enabling  this feature, only those AP's whose mac-addresses are present  in the  authorization list, will be able to register to the WLC. url...
 
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it. url...the forum I have seen other talks about the same issue and saying that  if I have any APs in "Rogue Detection"  mode sitting on the trunk port   on the switch then  only, this AP will detect the  Rogue on Wired.

View 2 Replies View Related

Cisco Switching/Routing :: Nexus 7k - Possible To Send Syslog Messages To SNMP Sever

Jul 2, 2012

Query is, Can i send my syslog messages to SNMP sever? if so, what command needs to be enabled on nexus 7k?

View 3 Replies View Related

Cisco Switching/Routing :: 1841 - Unable To Make Router To Send Syslog Messages To Server

Dec 15, 2012

I am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:

Sample router config:
 
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......

is there a command that prevents the router from sending the syslog to the server?

View 2 Replies View Related

Cisco Switching/Routing :: Configure 6500 To Respond To Messages As NTP Master

Feb 12, 2013

Setting up NTP. Currently the source for NTP within our network is our core 6500.Currently the NTP source for the 6500 are internet based NTP Servers. I would like to configure the 6500 to respond to NTP messages as the NTP Master. However will the 6500's source remain as the internet based NTP Servers?? In other words if the 6500is configured to be NTP Master, where would it get it's time from?

View 5 Replies View Related

Cisco Firewall :: Can Configure More Than One Syslog Host On ASA 5500

May 31, 2012

I would like to send my ASA 5500 logs to more than one syslog server - is this possible?  I can't seem to find it in the documentation.

View 3 Replies View Related

Cisco :: How To Configure LMS 4.0 To Capture Syslog From Network Devices

Aug 23, 2011

How can I configure my LMS 4.0 to capture syslog from network devices?
 
On the LMS CiscoWorks Portal, Syslog Alert window shows "No data is available".

View 1 Replies View Related

Cisco Switching/Routing :: 3750 - Configure Syslog Server For All Of Device Logging?

Feb 5, 2012

I'm looking to configure a syslog server for all of my cisco device logging. I've had a look at CNA and can't find any options to define a syslog server for my switches.
 
What's the best way to define a syslog server and the severity of the notifications? Also, i'm looking to clear all previous Syste mmessages fon my devices?

View 6 Replies View Related

Cisco Switching/Routing :: Configure 2951 To Send Logs To Kiwi Syslog Server?

Dec 21, 2011

I have configured my 2951 router to send logs to my Kiwi syslog server like below.

#logging 10.20.20.52
 
But I am not receiving any logs from my router, the same has configured on my asa5520 and its sending logs.

View 3 Replies View Related

Cisco Routers :: SA 500 - Ability To Send Syslog Events To Multiple Syslog Servers

Jul 7, 2012

Add the ability to send syslog events to multiple syslog servers in the SA500 Series routers.  I know the functionality is currently in the RV220W because we utilized it.  It would be great if you could configure the syslog servers by event type as well.  For example, being able to send the kernel events to syslog server A, and all other events to syslog server B.

View 0 Replies View Related

Cisco Firewall :: ASA 5500 Syslog Not Getting Captured In Centralised Syslog Server

Jan 15, 2012

Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.

View 3 Replies View Related

2650 (non-XM) With 12.4T (XM IOS)?

Dec 19, 2011

I have a rather large Cisco Lab and 3 of the routers I have are Cisco 2650s. Well they are only able to take the IOS version 12.4M and 12.4T is only compatible with the XM series.So I was thinking what would happen if I threw the 12.4T on the device, well I was surprised but it boots and functions with that image. So here is the question, is this usable in a LAB environment (CCNA/CCNP studies ect) the thing that would worries me is the memory. It is recommended the 12.4T IOS has (I think) 196D/48F. Well the 2650 non-xm only supports 128D/32F. The IOS fits on the 32 Flash (with 300k to spare) though what issues can/will i see in the future?

Code:
Cisco IOS Software, C2600 Software (C2600-ADVENTERPRISEK9-M), Version 12.4(9)T2, RELEASE SOFTWARE (fc4)
Technical Support: [URL]
Copyright (c) 1986-2006 by Cisco Systems, Inc.
Compiled Sat 18-Nov-06 14:32 by prod_rel_team

[code]....

View 1 Replies View Related

Cisco WAN :: 2650 - Telnet Usage With NAT

Feb 21, 2012

I have a  Cisco 2650 with a simple config as follows:

version 12.3
service timestamps debug datetime msec
service timestamps log datetime msec
no service password-encryption
!
hostname MaVI_Test
[Code]....

View 3 Replies View Related

2848 / 2650 - HP Procurve Stacking

Apr 17, 2012

I have 2 procurve switches
2848
2650

Procurve stacking? Is that just a way too manage both switches together?

Or is it for combining both switches together?
Or is that called something else in procurve speak?
Or is that feature not actually available etc?

Next to learn how to breakup the 2848 into multiple switches.

View 18 Replies View Related

HP Pro Curve 2650 And 2610 VLAN Infrastructure?

Mar 3, 2013

I have 2 Procuve Switches one is 2650 were all the Department PC's & Wireless access points connected & second one is 2610 were i have the firewall connected,Active Directory & Windows DHCP Server

Switch 1- 2650
Ports
Port 1-16 is used by HR Department
Port17-32 is used by Finanace Department
Port 33-34 is used by Access Points
Port 41-48 is used by Users

Port 50 is used to uplink to switch 2610.What i wanted to achive is Isolcate Departments & Users & Access Points through VLAN from each other but they should be able to hit our Active directory for authentication, Firewall for internet & DHCP Server for IP's.

View 3 Replies View Related

Cisco Switching/Routing :: 2650 - Getting Enable Mode On Router?

Jan 14, 2012

On my 2650 Router it just has only Telnet password.It has no enable mode password set.After reboot it is goes to prompt mode BB.I am unable to go to enable mode .how can i go back to enable mode on this router?

View 13 Replies View Related

Cisco Switching/Routing :: 2650 / 2620 - Support For MPLS

Oct 29, 2011

Does 2650 and 2620 support MPLS ? If yes what IOS version should i download?

View 10 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved