We started getting the below syslog messages from one of our ASA5520 which was recently upgraded to 8.4(2). Any bugs on 8.4(2) that cause this or its simply the RAM failure?
%ASA-3-105010: (Primary) Failover message block alloc failed
%ASA-3-321007: System is low on free memory blocks of size 1550 (0 CNT out of 18709 MAX)
I keep getting an error message, i've tried several things to resolve it but still no success.This is the exact error message:
regular translation creation failed for protocol 41 src Customer: dst outside:
I'm getting the Syslog messages frequently on daily basis.
View 4 Replies View RelatedI have a new install of LMS 4.2 on a virtual appliance. No syslog messages are getting into LMS. They are being received by the server, but are showing up in /var/adm/CSCOpx/log/dmgtd.log, and aren't getting processed by SyslogAnalyser.
View 3 Replies View RelatedLMS 4.1 is not showing any valid syslog messages, only invalid messages. Is there anything different in 4.1 that needs to be set?
View 2 Replies View RelatedMy Cisco devices send syslog messages to LMS but it wont`t show any messages from device. Older LMS 3.2 and other collector showe all syslog messages. What to do with LMS 4.0.1?
View 2 Replies View RelatedI have a newly installed LMS 4.1 that had the Syslog feature working for a while.
Recently, the Syslog is no longer displaying any records (neither new or old messages).
Below are the steps I have tried to troubleshoot the problem:
- Installed wireshark : Syslog messages are being received by the LMS server on time
- In the Syslog.log file, I can see that all the Syslog messages are being logged properly
- I tried to disable all the "Syslog Message Filters" but nothing changed
In the SyslogCollector.log, I can find the below logs:
NMSROOT is C:/PROGRA~2/CSCOpx
propFileC:/PROGRA~2/CSCOpxMDC omcatwebapps
meWEB-INFclassesC:PROGRA~2CSCOpxMDC omcatwebapps
[Code]....
I have a small problem with a lot of invalid syslog messages in LMS 3.2. Something about 30% of all messages are invalid.
Is there any posibility to get out from which devices those messages are?
Is it a big problem for the application if there are such a lot of invalid messages? I have a lot of devices in my LMS and don't want to get high load because of such unneeded messages.
Is there a way to debug syslog messages? Something like "debug ip syslog"?
View 11 Replies View RelatedI'm trying to configure an ASA firewall (FW2) for syslog and tacacs and am experiencing strange behavior. Both the syslog and ACS server are on the inside of another firewall (CoreFW). Whenever a log message is generated on FW2 the request is dropped by CoreFW and message '%ASA-4-313004: Denied ICMP type=0, from laddr FW2 on interface outside-b2b to syslog01: no matching session' is displayed. The same thing occurs for tacacs.
It appears that the syslog and ACS requests are generating ICMP echo replies, which the core firewall drops since no session exists on a lower security interface. I have access lists configured on CoreFW to allow the syslog and tacacs requests.
FW2 is running asa825-k8.bin, CoreFW is asa824-k8.bin
I've just taken over a new network with a Cisco ASA5520. Everything is working fine, except I am being bombarded with 106001 alerts from a few internal hosts to one specific internal host. The description in general is "Inbound TCP connection denied from 10.1.0.1 to 10.1.0.5 - both of those are valid internal hosts and the TCP ports are also valid. I tried looking at the log and getting it me to tell me which rule was causing these alerts, but it just came back with 'It's not possible for these type of alerts'
- How is it possible for the ASA to even pick up on this when, in theory, the source host wouldn't be going near the ASA since it's on the same subnet?
- What might be causing this?
- How can I turn it off!! (I guess that'd be fixed by point 2)
Is there a way to get more messages out of a 2950 set to syslog? I've turned every logging option I can find to DEBUG, but all I get in my syslog are LinkUp/Down messages and "Configured from console by console". I'd love to see more information such as configuration changes, or even someone attempting to set up DTP on a switchport set to access mode.
View 2 Replies View RelatedI bought a RV110W wireless router a couple months ago that I've been pretty happy with.
However, I have one significant problem with it. It is configured to send syslog messages to an internal server. Twice now it has gone into a mode where it starts dumping messages like,
ip_conntrack_is_ipc_allowed: ipc_entry_is_full
continuously, at a rate of about 20 per second. It otherwise seems to function normally, but of course if unnoticed my syslog file quickly grows to hundreds or thousands of megabytes. A reboot restores normal operation. It is running firmware 1.1.0.9. A search on the internet turned up no information about this problem.
It may be some corruption is occuring in the router's OS, or perhaps this is something that can be triggered externally (in which case it would be a weak form of DoS attack? Or maybe worse if in this state it is unable to properly apply the firewall rules.)
I want to use IP SLA to perform simple up/down monitoring of an IP host and to generate a syslog alert if the host goes down. I have a 2650XM router running 12.4(23) IP Voice IOS. My basic IP SLA config is hown below:
ip sla monitor 10
type echo protocol ipIcmpEcho 10.55.1.1
timeout 1000
frequency 10
ip sla monitor schedule 10 life forever start-time now.
how can I configure ACS 5.2 to send syslog messages to CS-MARS?
View 3 Replies View RelatedI'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior. I'm doing this step.
Authorize AP's against AAA function to make sure that all the AP's registering to your WLC are authorized AP's of the network.By enabling this feature, only those AP's whose mac-addresses are present in the authorization list, will be able to register to the URL
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it.URL
NOTE: from the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection" mode sitting on the trunk port on the switch then only, this AP will detect the Rogue on Wired
I don't think i completely understand this statement, by sitting does it mean that it is passively sniffing coming in/out on trunk link?
Considering the above steps are accurate, after this will i be able to see rogue detection behavior in syslogs? What exactly would be the messages that would produce this behavior.
Is there any way to change the port that is used for syslog messages on a Cisco 9500 switch?By default this is set to UDP port 514.There doesn't seem to be a command to change the port.
View 1 Replies View RelatedI have an issue with the syslog of 7600 router, I have configured the logging level to informational, but when I execute changes such as up or down an interface, the syslog messages aren't displayed? Why is the reason? This symptom exist after I changed the buffer size from default to 32768.
Router#sh log
Syslog logging: enabled (0 messages dropped, 0 messages rate-limited, 2 flushes, 0 overruns, xml disabled, filtering disabled)
No Active Message Discriminator.
No Inactive Message Discriminator.
Console logging: disabled
Monitor logging: level debugging, 40 messages logged, xml disabled,
[code]....
I'm building the use case to test / detect for rogue devices on the network. I have in my enviroment Lan controller 5500 controller with AP (aironet 3500). I want to detect for rogue devices/ap connected to my network. I know before i can see this activity on the network i have to configure the controller / ap to detect this behavior.
Authorize AP's against AAA function to make sure that all the AP's registering to your WLC are authorized AP's of the network.By enabling this feature, only those AP's whose mac-addresses are present in the authorization list, will be able to register to the WLC. url...
Using Rogue detection. feature, the WLC will be able to detect any AP that is not a part of its RF group and contain it. url...the forum I have seen other talks about the same issue and saying that if I have any APs in "Rogue Detection" mode sitting on the trunk port on the switch then only, this AP will detect the Rogue on Wired.
Query is, Can i send my syslog messages to SNMP sever? if so, what command needs to be enabled on nexus 7k?
View 3 Replies View RelatedI am using Solawinds syslog and trying to get our Cisco routers send syslogs to our syslog server. I followed the procedure on Configuring Cisco Devices to Use a Syslog Server from [URL] Our Cisco swtches are all sending syslog messages but not the routers. I compared the config with our access switches but can't seem to find the problem:
Sample router config:
service nagleno service padservice tcp-keepalives-inservice tcp-keepalives-outservice timestamps debug datetime msec localtime show-timezoneservice timestamps log datetime msec localtime show-timezoneservice password-encryption!hostname WWF-RT1boot-start-markerboot-end-marker!security authentication failure rate 10 logsecurity passwords min-length 8logging buffered 4096logging rate-limit all 10logging console critical!aaa new-model!!
[Code] .......
is there a command that prevents the router from sending the syslog to the server?
Recently i have upgraded the IOS of ASA5550 (in HA mode) to 8.4.2 from 8.0.5, after OS upgrade we found that the syslog from thses firewalls are not getting captured/transfered to centralised syslog server. The server is reachable from the firewalls.
View 3 Replies View RelatedAny step by step guide to setup syslog for site to site VPN.(in ASA 5520)Just send me the step to monitor site to site vpn using that in ASA 5520.
View 2 Replies View RelatedI have configured the primary firewall every thing seem to be fine, And we have configured fail over device while config is getting replicated to the fail over device we are getting below error.
ERROR: Cannot add policy to rule engine
ERROR: Unable to assign access-list LAN_out to interface inside
IOS and Model are same.But all the config got replicated from primary to secondary but except the one access group command.
access-group LAN_out in interface inside.
When trying to access the asa (8.0(3)) with asdm the console send follwing error message:
vPif_isVpifNumValid: pifNum out of range!
vPif_getVpif: bad vPifNum(0xa6) from 87EBC81 from 83833B4
Have a strong suspicion that it is a hardware failure (since asdm has worked and have tried to restart the box) can not see any errors with any show commands, but could it be a RAM error .
I am constantly getting a few errors in my ASA 5510 and 5505 from the same IP. The IP of my NMS server, which has also stopped recieving SNMP data from these two VPNs.
Syslog Id: 713048 Error process payload: Payload ID: 1
Syslog ID: 713902 Removing peer from peer table failed. No Match.
Syslog ID: 713903 Error: Unable to remove PeertblEntry
I have tried to configure ACL to let traffic through. SNMP traffic to be more precise, but since I am fairly new to cisco firewalls and SNMP in general this has proven very difficult.
Our building used to have a very old server that basically just served as a place for teachers to store files and not much else. We have just changed ISPs and decided that we no longer needed the server at all. I disconnected the server from the network and replaced the old ISP's modem with the new ISP's modem. At first, everything seemed OK. My computer and several other teachers' connected to the Internet with no problem. However, some of the computers in the building could not connect. We get error messages with "limited or no connectivity." Part of me thought that perhaps the connections themselves are bad. However, when I take my laptop to classrooms with trouble connecting - mine connects easily using their cables. If I move their computers to my room, their laptops still won't connect. I have put my computer side-by-side with another one to make sure the settings were the same (auto-detect IP, DNS, etc.) and can't find differences. This problems is affecting our Windows 7, Vista, and XP computers the same.
View 11 Replies View RelatedYesterday after booting my comp up I wanted to get on the internet but for the first time in years with my set up it just wouldn't connect, never done this before, we have a wireless O2 box upstairs which my son has a ethernet directly from the wireless router into his comp and my other son has a notebook (same as mine) and both of them were online but mine just wouldn't connect although I had nothing to say anything was wrong, o2 told me that if the other computers were online then it must be something on my comp that is causing the trouble ? but what could it be ? after three hours offline I rebooted and it was fine and got onto the internet no trouble, this morning it again wouldn't let me online and then bingo it just came on again at 4pm very strange to me
View 3 Replies View RelatedAbout three(3) months ago, I attempted to set up a wired network between a laptop running w-7 and a desktop with w-xp, sp3. Shortly afterwards, I started getting blue screens with error messages and codes about device confilcts. After disconecting the laptop, I still have the problem sometimes. I looked into the system, and found twenty-seven(27) items with yellow exclamation marks on them. Should I delete them or just disable them?
View 3 Replies View RelatedI am using LMS3.2, but it is not able to collect running config, and startup config from asa 5520. LMS is able to collect all syslog from asa.
View 4 Replies View RelatedI had these error messages on both my Cisco 2851 and on my Cisco Catalyst 6506.
On Cisco 2851:
%SYS-SP-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (4/4),process = SEA write CF process. [code]...
And on 6506:
Dec 27 15:20:55 MET: %SYS-SP-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (129/129),process = SEA write CF process.[ code]...
I have these IOS versions on my Cisco:
Cisco 2851: 15.0(1)M4
Cisco 6506: 12.2(33)SXI
i have currently a 2504 WLC and some 1602i AP's.Basically so far i have configured the WLC as per the guidelines on the startup and now i want to join the AP's (which i haven't managed to do yet) and the setup the wireless network.I can get the AP to join and pickup an ip address and that is it. It comes up with different error messages from the WLC, and through hyper terminal, none of which i understand but the main jist is the following:
*spamApTask4: Feb 19 15:05:56.171: #CAPWAP-3-DECODE_ERR: capwap_ac_sm.c:3844 Error decoding Join request from AP 6c:20:56:0e:23:e0
AND
0Tue Feb 19 15:06:19 2013AP with MAC 6c:20:56:0e:23:e0 (AIR-CAP1602I-E-K9 ) is unknown.
AND
We have 2 Cat 6509 connected to 1 Gbps Ethernet WAN Link. On each 6509 we use 2 Gbps IPSec SPA Encryption cards for Encryption. The encrypted traffic goes to a GRE Tunnel. This morning I found some error messages in syslog.
%CONST_DIAG-SP-3-HM_TEST_FAIL: Module 1 TestIPSecEncrypDecrypPkt consecutive failure count:2
There were also several short tunnel downs/ups. I wonder if there is a bug in the new IOS image 12.2(33)SXI2a. We upgraded to this image last weekend.