Cisco :: Constant Error Messages In ASA 5510 From The Same IP?
Nov 27, 2012
I am constantly getting a few errors in my ASA 5510 and 5505 from the same IP. The IP of my NMS server, which has also stopped recieving SNMP data from these two VPNs.
Syslog Id: 713048 Error process payload: Payload ID: 1
Syslog ID: 713902 Removing peer from peer table failed. No Match.
Syslog ID: 713903 Error: Unable to remove PeertblEntry
I have tried to configure ACL to let traffic through. SNMP traffic to be more precise, but since I am fairly new to cisco firewalls and SNMP in general this has proven very difficult.
View 8 Replies
ADVERTISEMENT
Nov 27, 2011
Using a Samsung Galaxy S2, iPod Touch 3rd Gen, and Nook Color, they are all experiencing retry problems, even when 3 feet from the DIR-601. When I use them my log gets filled with messages like:Blocked incoming TCP Ack packet from 192.168.100.201:2926 to 209.85.145.113:80 with unexpected sequence On the devices I see the downloads/content taking a long time to appear and often I get a blank page or "Retry" messages. I purchased two DIR-601s and get the same problem with both. They are both running 1.02NA firmware. The WLAN is Time Warner cable modem. Prior to this I had a Linksys WRT-54 that gave great performance, though just at B/G speeds. I was hoping for a performance boost but right now the N speeds are slower than B with the retries.
View 5 Replies
View Related
Mar 13, 2013
I have a brand new 2960S-48TS-L, plain vanilla with no extra module/boards etc. It boots up ok (the installed version is 12.2 (55) SE5) but then constantly cycles the following error, and doesn't accept any input whatsoever. After 5-10 minutes of cycling the error, the switch reloads and starts the process again.
PCIE0: link is NOT up.
--------------CPU's PCIe SDR Registers--------------------
PE_DLPSET = 00401000
PE_UTLSET1 = 00000000
[Code]......
View 2 Replies
View Related
Jan 20, 2011
Our building used to have a very old server that basically just served as a place for teachers to store files and not much else. We have just changed ISPs and decided that we no longer needed the server at all. I disconnected the server from the network and replaced the old ISP's modem with the new ISP's modem. At first, everything seemed OK. My computer and several other teachers' connected to the Internet with no problem. However, some of the computers in the building could not connect. We get error messages with "limited or no connectivity." Part of me thought that perhaps the connections themselves are bad. However, when I take my laptop to classrooms with trouble connecting - mine connects easily using their cables. If I move their computers to my room, their laptops still won't connect. I have put my computer side-by-side with another one to make sure the settings were the same (auto-detect IP, DNS, etc.) and can't find differences. This problems is affecting our Windows 7, Vista, and XP computers the same.
View 11 Replies
View Related
Oct 12, 2012
Yesterday after booting my comp up I wanted to get on the internet but for the first time in years with my set up it just wouldn't connect, never done this before, we have a wireless O2 box upstairs which my son has a ethernet directly from the wireless router into his comp and my other son has a notebook (same as mine) and both of them were online but mine just wouldn't connect although I had nothing to say anything was wrong, o2 told me that if the other computers were online then it must be something on my comp that is causing the trouble ? but what could it be ? after three hours offline I rebooted and it was fine and got onto the internet no trouble, this morning it again wouldn't let me online and then bingo it just came on again at 4pm very strange to me
View 3 Replies
View Related
May 10, 2012
We started getting the below syslog messages from one of our ASA5520 which was recently upgraded to 8.4(2). Any bugs on 8.4(2) that cause this or its simply the RAM failure?
%ASA-3-105010: (Primary) Failover message block alloc failed
%ASA-3-321007: System is low on free memory blocks of size 1550 (0 CNT out of 18709 MAX)
View 2 Replies
View Related
Aug 8, 2011
About three(3) months ago, I attempted to set up a wired network between a laptop running w-7 and a desktop with w-xp, sp3. Shortly afterwards, I started getting blue screens with error messages and codes about device confilcts. After disconecting the laptop, I still have the problem sometimes. I looked into the system, and found twenty-seven(27) items with yellow exclamation marks on them. Should I delete them or just disable them?
View 3 Replies
View Related
Dec 26, 2010
I had these error messages on both my Cisco 2851 and on my Cisco Catalyst 6506.
On Cisco 2851:
%SYS-SP-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (4/4),process = SEA write CF process. [code]...
And on 6506:
Dec 27 15:20:55 MET: %SYS-SP-3-CPUHOG: Task is running for (2000)msecs, more than (2000)msecs (129/129),process = SEA write CF process.[ code]...
I have these IOS versions on my Cisco:
Cisco 2851: 15.0(1)M4
Cisco 6506: 12.2(33)SXI
View 3 Replies
View Related
Feb 18, 2013
i have currently a 2504 WLC and some 1602i AP's.Basically so far i have configured the WLC as per the guidelines on the startup and now i want to join the AP's (which i haven't managed to do yet) and the setup the wireless network.I can get the AP to join and pickup an ip address and that is it. It comes up with different error messages from the WLC, and through hyper terminal, none of which i understand but the main jist is the following:
*spamApTask4: Feb 19 15:05:56.171: #CAPWAP-3-DECODE_ERR: capwap_ac_sm.c:3844 Error decoding Join request from AP 6c:20:56:0e:23:e0
AND
0Tue Feb 19 15:06:19 2013AP with MAC 6c:20:56:0e:23:e0 (AIR-CAP1602I-E-K9 ) is unknown.
AND
View 8 Replies
View Related
Dec 25, 2012
I have a WLC 5508 and several 1142 access points. The APs are not showing up in the WLC. When i console into the APs, im getting the following errors,
*Dec 26 23:04:28.035: %DTLS-5-SEND_ALERT: Send FATAL : Close notify Alert to 65.125.15.212:5246
*Dec 26 23:04:28.074: %CAPWAP-5-CHANGED: CAPWAP changed state to
[Code]....
Ive tried resetting the WLC, reloading the APs. I even factory defaulted one of the APs and still getting the same message.Ive verified that the WLC is set to accept MICs and SSCs.
View 6 Replies
View Related
Sep 30, 2012
We use C2950G switches with IOS 12.1(22)EA12 . Switches are set up to send logs to a server (informationnal level). On this server, we receive many of logs from those switches, but none about interfaces errors (even if interfaces statistics show interfaces errors). On C3548 switches it's work fine.How should I be sure the set up of switches is correct ? Why do I never receive messages as %LINK-4-ERROR:[char] is experiencing errors ?
View 2 Replies
View Related
Aug 15, 2011
I m getting below error messages in show logs -
Aug 12 15:30:57.127 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:02.175 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:08.219 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
Aug 12 15:31:10.239 IST: %ENVIRONMENT-3-RPS_FAILED: Faulty internal power supply detected
there is no error messages related to PSU in "show env all " log .
here is show version -
------------------ show version ------------------
Cisco Internetwork Operating System Software
IOS (tm) C2950 Software (C2950-I6K2L2Q4-M), Version 12.1(22)EA13, RELEASE SOFTWARE (fc2)
Technical Support: [URL]
Copyright (c) 1986-2009 by cisco Systems, Inc.
[Code] ....
View 8 Replies
View Related
Jan 25, 2012
I'm starting to see an error creep up that I havn't seen since 2003/2004 on my brand new 5508 controllers. I'm recieving the following from my WCS: Receive Multicast Queue is full on Controller and then on the controller itself RX Multicast Queue Full. I understand this used to be due to a large influx of ARP requests or CDP packets on older controllers but, this was supposed to be fixed in an update many years ago.
Has seen this on their 5508's. These were advertised as having the horsepower to handle our user loads which arn't really that high at 300 users at any given time max.
View 2 Replies
View Related
Dec 31, 2011
I have an 5510 ASA with 804 IOS. In that installed anyconnect (anyconnect-win-2.0.0343-k9.pkg) version. But when i am going to connect it from https:// I am getting the below error. So as a work around i tried to install anyconnect-win-2.5.6005-pre-deploy-k9.msi at my laptop and try to connect from https:// i am able to connect.
View 4 Replies
View Related
Nov 10, 2011
I have a ASA 5510 behind a 2911 router. I've trying to configure a remote access and site to site vpn tunnel. I've started on the remote access, and I have it setup, but I'm getting this error message with trying to authenicate from the VPN client (412 error)?
Nov 11 09:52:45 [IKEv1]: IP = 68.51.100.192, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + HASH (8) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 428
Nov 11 09:52:51 [IKEv1]: Group = tfx-tg, IP = 68.51.100.192, Duplicate Phase 1 packet detected. Retransmitting last packet.
[code]....
View 5 Replies
View Related
Aug 21, 2011
I have a cisco ASA5510 and I'm having fun experience some configurations.I can not connect to VPN, windows me error 809. I configured the firewall to accept connections to microsoft L2PT/IPsec client by authenticating users on the domain controller LDAP.
Clientless vpn connection work, so the server connection is correct. [Code] ......
View 12 Replies
View Related
Aug 21, 2012
I recently bought an all brand new ASA 5510 and it is here by my side. I'm trying to configure it but when entering https://192.168.1.1/admin I get Page Not Found error on IE. I'm able to ping 192.168.1.1 and have success telnet 443 port.
View 13 Replies
View Related
Oct 16, 2012
I have configured remote access VPN with radius authentication in my firewall ( ASA 5510). When tried to connect the VPN with Cisco vpn client, the following error is showing,
"Error: Secure VPN connection terminated by Peer. Reason 433 (Reason not specified by peer)".
View 1 Replies
View Related
Sep 1, 2011
I'm opening a new topic related to my problem with the VPN connection, to avoid confusion, since there are many, in the old information, no longer required.
I would like to configure my ASA5510 L2PT/IpSec to accept connections from Windows clients. I happen to authenticate via AD credentials. When I try to connect is because the error 691. I enabled debugging on the machine the following:
debug crypto isakmp 3
debug crypto ipsec 3
debug ldap 255
View 4 Replies
View Related
Mar 5, 2013
I am trying to add 89,462+ access list rules to an ASA 5510 running 8.2(5). I have added all the rules to an object group and when I try to apply the access list to an interface it gives me the following error:
ERROR: Cannot add policy to rule engine ERROR: Unable to assign access-list wan-out to interface wan
I have not tried not using an object group and just putting the rules in the access list. I want to be able to add to these rules if needed easily.
I think it's clear that i have exceeded the rule limit for the ASA. So my question is, what is the rule limit for an ASA 5510 and which ASA could I purchase that would handle this amount of rules?
View 1 Replies
View Related
Oct 11, 2011
I've got some problem with my Mail Server since I've migrated to an ASA5510.Actually the server is in a DMZ with a private Ip ( 10.x.x.2) and it is translated to a Public IP ( 194.x.x.65).I use these configuration :
static (DMZ,LAN) 194.x.x.65 10.x.x.2 netmask 255.255.255.255 static (DMZ,LAN) 194.x.x.66 10.x.x.3 netmask 255.255.255.255 static (DMZ,WAN) 194.x.x.65 10.x.x.2 netmask 255.255.255.255 static (DMZ,WAN) 194.x.x.66 10.x.x.3 netmask 255.255.255.255 static (LAN,DMZ) 192.168.0.0 192.168.0.0 netmask 255.255.248.0
Some Users received in there mailbox a system administer error message :
Object : Impossible to deliver : test Your message could not be deliver to one or more of its recipients: 421 SMTP connection went away!
When they try to re sent it some times later, message is sent without problem.
View 4 Replies
View Related
May 31, 2011
I have a 5510 with just a inside and outside interface, everything works on the lan inc internet access and exchange hosting to the net, but I have another exchange server on the wan and I can't get to that because I'm not natting inbound traffic and the default route sends traffic elsewhere.
If I put a nat any statement on the inside interface inbound it works, however all LAN internet traffic fails with a No translation group found error.I've removed the static nat commands as they are all named anyway, but below is what I have before I do a nat any inside inbound command global (outside) 1 interfaceglobal (inside) 2 interfacenat (inside) 0 access-list inside_nat0_outboundnat (inside) 1 0.0.0.0 0.0.0.0.
View 3 Replies
View Related
Feb 1, 2012
My printer has an error saying cannot connect to network......this problem occurred when i made a secure internet connection. I have tried resetting everything , unistalled printer software, i have changed all kinds of things on my router page . Apparently not the right things. I have a Dlink 524 router , Hp photosmart 5510 printer and 2 laptops.
View 1 Replies
View Related
Jan 3, 2013
my Cisco ASA 5510 doesn't save the configuration to the disk.
View 1 Replies
View Related
Feb 4, 2012
I have turned on the aaa command authorization without applying adequate privileges to the user. I can now log in through that user but the ASA 5510 displays an error :ASA 5510# show running-config
ERROR: % Invalid input detected at '^' marker.
ERROR: Command authorization failed.
I am unable to make any configuration changes on the firewall. Is there any default user through which I can log in and disable the aaa authorization ? if not, how can I resolve this situation ?
View 1 Replies
View Related
Apr 28, 2011
Connection denied due to NAT reverse path failure
View 2 Replies
View Related
Apr 29, 2012
we recently purchased a sg300-52. i was told i would need to setup a port trunk to connect it our main catalyst. However, i was able to connect a patch cable on the two devices and ping endpoint devices on both switches. I also noticed that the activity lights are constantly blinking. I'm not sure why. Is there something i can do to slow the activity light? it blicks constantly even in times of very low activity by the endpoint.
View 2 Replies
View Related
Sep 17, 2012
I am not good at networking. My friend wanted me to set up his home network.because the modem is unable to supply a good wireless connection to the rest of the household when the door is closed, a second router was needed.I set both routers to run with DHCP as they have many devices that needs to connect to the router for internet. However, a few hours after setting it up, my friend's pc as well as all devices connected to the second router faced issues. The router's interface showed that it does not have connection to the internet. they are still facing this problem until now.
View 7 Replies
View Related
Dec 21, 2011
I keep getting disconnect from the internet about every 10-15 minutes.I had a tech from cableone come over yesterday he installed all new wiring and a new modem.how can i tell if it's my computer that is the problem or if it's just a service i need to get rid of?
View 8 Replies
View Related
Sep 12, 2011
I currently live in a fairly-large apartment in Downtown San Francisco and as you can probably imagine, I have ALOT of interference with nearby residential and business wifi's, microwave's, cell-phones and all that jazz.
I currently have the ATT Elite DSL package, which is I believe the 6MBPS(?) package? Anyway, it's the $40 package and I want to say it's either the second or third up from the basic 19.95/month subscription. Here's my problem: ever since I moved into this building, I get signal drops on my ATT all the time--like at least once an hour if not more often. I had a technician check the wiring and he even replaced the router box (they always do) in hopes of improving the situation but so far, no dice.
I have tried switching to different channels after using scanning to see what channels other internet users nearby were using, but I did not see any improvement.The best solution I've been able to come up with is to set my router to be on 802.11B only. For the most part,I have not disconnected but I do feel a certain amount of slow-down or lag compared to my 802.11G settings.Now,I might be paranoid but it certainly does take a good amount of time longer to load up pages and such as compared to previously.The tech suggested I look towards getting an 802.11A/N router, but alas ATT does not support routers of that caliber...not sure why. It's been years and they're still stuck with the 2Wire 2701HG-B model for DSL.
View 2 Replies
View Related
May 2, 2011
About twice a week lately I'm having to reboot my router. All connections don't work. Logs captured don't show any time stamping so not as good as I was hoping but I do have some debug data:
View 1 Replies
View Related
Apr 8, 2012
My router was working fine. Then 1 day I started having slow internet. My ping in games would jump up from ~60 to about 400-800. Did some troubleshooting with my ISP. Seemed like my modem was to blame. So I bought a Netgear one from BestBuy.
Everything was fine. Then 1 day the internet stated disconnecting. None of the computers could see the router in the wireless networks. I found the only way to solve the problem is to unplug the power and plug it back in. Strangely it seems to happen a lot late at night like around 11PM or 12 midnight EST.
Before with my old modem I just had automatic settings and DHCP. With the new modem it wouldn't work so I called DLink and the tech guy walked me through some steps, one of which was changing the ip address from 192.256.0.1 to 10.10.10.1. Whenever I reboot the router after a disconnect the computers say "there was an IP address conflict." Maybe this has something to do with it?
I saw in another topic someone said their router's time was wrong. Mine said it was 2010 so I updated it to automatically sync with ntp1.dlink.com and now it shows 2012. Let's see if it fixes now. My mom's laptop had a similar problem with Skype. For some reason the clock kept resetting to 2000 and Skype would not work (everything else did). When she resets the time to 2012 it starts working again.
View 1 Replies
View Related
Jan 31, 2012
Model E2000
Firmware: 1.0.04
Using 2.4 channels
All devices that are connected wireless through this access point have the difficulty of dropping internet momentarily. When ping from wireless devices to comcast.com with -t I get:
This happens about once every minute. Wireless connection itself does not drop just access to the web. Every single wireless device does the same thing including Ipad, ipod, mac and windows machines. Two machines that are directly wired into the router do not have this problem. Thier Ping status stay at around 60ms. Things I have tried:
adjusting MTU
Beacon interval in both faster and slower directions
Fragmentation threshold
RTS threshold
Made sure no other devices in range are on same channel
firmware updates
different security settings
changing SSID
This is causing streaming problems for both security cameras and client music.
View 1 Replies
View Related
