I have an 5510 ASA with 804 IOS. In that installed anyconnect (anyconnect-win-2.0.0343-k9.pkg) version. But when i am going to connect it from https:// I am getting the below error. So as a work around i tried to install anyconnect-win-2.5.6005-pre-deploy-k9.msi at my laptop and try to connect from https:// i am able to connect.
View 4 Replies
tying to connect CSM client to CSM server (ver 4.0) and getting attached error message. The server is running, no errors reported while installation, all services are up and fine. I tried to install client locally on the server and connect it that way with no luck. CSM server runs on Win 2008, firewall disabled.
View 0 Replies View RelatedI am unable to connect to the vpn I set up on my ASA 5505 using the Cisco VPN Client on a Windows machine. The log of the vpn client and the config of the ASA 5505 are below.
LOG CISCO VPN CLIENT
Cisco Systems VPN Client Version 5.0.06.0160
Copyright (C) 1998-2009 Cisco Systems, Inc. All Rights Reserved.
[Code]......
I have a ASA 5510 behind a 2911 router. I've trying to configure a remote access and site to site vpn tunnel. I've started on the remote access, and I have it setup, but I'm getting this error message with trying to authenicate from the VPN client (412 error)?
Nov 11 09:52:45 [IKEv1]: IP = 68.51.100.192, IKE_DECODE SENDING Message (msgid=0) with payloads : HDR + SA (1) + KE (4) + NONCE (10) + ID (5) + HASH (8) + VENDOR (13) + VENDOR (13) + VENDOR (13) + VENDOR (13) + NAT-D (130) + NAT-D (130) + VENDOR (13) + VENDOR (13) + NONE (0) total length : 428
Nov 11 09:52:51 [IKEv1]: Group = tfx-tg, IP = 68.51.100.192, Duplicate Phase 1 packet detected. Retransmitting last packet.
[code]....
my net is connecting so late after a sudden hang in windows, and sometimes showing Error 718..It has become very often...I asked my friends (same connection), they are not having any problem from the ISP... what's wrong? :/ Few minutes ago, it was showing error 718, i had to restart, and then it connected (still slowly).
Core2Duo, Dg41Rq, @2.93Ghz, 2Gb DDR2, 500Gb HD, avast free, Ethernet connection braodband PPPoE via landline.
I had been working on our client servers through Cisco VPN using internet datacard. But from past 3 weeks after logging into Cisco VPN using my username/password, when I try to connect to any of the servers, it is giving connection timed out error.
Whereas, my team members across other locations are able to connect to the servers using my VPN username/password.
I thought there might be some issue with my laptop or internet datacard. I got my laptop formatted, even tried out with fresh new laptops & new internet datacards, but the issue remains same.
I have tried using vpn_5.0.06.0160-k9 & vpnclient-5.0.05.0290-k9 to connect but issue did not get resolved.
I'm having a problem with a cisco bridge WET200 we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge but the equipment is not communicating with the gateway, with nothing!WLC always appears the following error:
WiSM-slot9-1) >debug client XX:XX:XX:XX:XX:XX
(WiSM-slot9-1) >*apfReceiveTask: May 23 12:03:27.953: XX:XX:XX:XX:XX:XX Deleting mobile on AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Adding mobile on LWAPP AP XX:XX:XX:XX:XX:XX(0)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Association received from mobile on AP XX:XX:XX:XX:XX:XX
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX 0.0.0.0 START (0) Changing ACL 'Guest' (ACL ID 0) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1393)
*apfMsConnTask_0: May 23 12:04:11.109: XX:XX:XX:XX:XX:XX Applying site-specific IPv6 override for station XX:XX:XX:XX:XX:XX - vapId 5, site 'default-group', interface
[code]....
i have test command config network ip-mac-binding disable but It does not connect....when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured?
I'm having a problem with a cisco bridge WET200.we have a medical equipment whit fixed IP and it has to connect to a wireless network ... and for that I set up the wireless network ... in this bridge [code] but the equipment is not communicating with the gateway, with nothing!
when I do the troubleshooting mac-client, the system always shows authentication error even though it is okay configured
I am constantly getting a few errors in my ASA 5510 and 5505 from the same IP. The IP of my NMS server, which has also stopped recieving SNMP data from these two VPNs.
Syslog Id: 713048 Error process payload: Payload ID: 1
Syslog ID: 713902 Removing peer from peer table failed. No Match.
Syslog ID: 713903 Error: Unable to remove PeertblEntry
I have tried to configure ACL to let traffic through. SNMP traffic to be more precise, but since I am fairly new to cisco firewalls and SNMP in general this has proven very difficult.
I have a cisco ASA5510 and I'm having fun experience some configurations.I can not connect to VPN, windows me error 809. I configured the firewall to accept connections to microsoft L2PT/IPsec client by authenticating users on the domain controller LDAP.
Clientless vpn connection work, so the server connection is correct. [Code] ......
I recently bought an all brand new ASA 5510 and it is here by my side. I'm trying to configure it but when entering https://192.168.1.1/admin I get Page Not Found error on IE. I'm able to ping 192.168.1.1 and have success telnet 443 port.
View 13 Replies View RelatedI have configured remote access VPN with radius authentication in my firewall ( ASA 5510). When tried to connect the VPN with Cisco vpn client, the following error is showing,
"Error: Secure VPN connection terminated by Peer. Reason 433 (Reason not specified by peer)".
I'm opening a new topic related to my problem with the VPN connection, to avoid confusion, since there are many, in the old information, no longer required.
I would like to configure my ASA5510 L2PT/IpSec to accept connections from Windows clients. I happen to authenticate via AD credentials. When I try to connect is because the error 691. I enabled debugging on the machine the following:
debug crypto isakmp 3
debug crypto ipsec 3
debug ldap 255
the specified destination is not reachable. connecting error 769
View 2 Replies View Relatedi got an error while connecting to my PIX (515e) via ssh connection there is an error message appears (The server has disconnected with error, server message reads: Internal Error) and at the console session at the time time, the following message appears also (process_create: out of memory)
View 1 Replies View RelatedI am running a Windows 7 Professional 32 bit as my office computer. About 3 PCs in the office are connected to the office server through wireless connection (including mine), and another 3 are connected through a wired connection. My connection to the server doesn't work at times. I get an error message that "An error occurred while connecting to . The network path was not found." The other PCs using the network have no problem connecting to the server. Also, the internet connection is shared from the server and I have no trouble with it. The problem is only with accessing the shared folder on the server.
View 1 Replies View RelatedEverythings works great except thee fact that my DIR-615 router
(Hardware Version: H1 Firmware Version: 8.00) logs the following error :
[SYSTEM]: DDNS error connecting to members.dyndns.org:80
I am trying to add 89,462+ access list rules to an ASA 5510 running 8.2(5). I have added all the rules to an object group and when I try to apply the access list to an interface it gives me the following error:
ERROR: Cannot add policy to rule engine ERROR: Unable to assign access-list wan-out to interface wan
I have not tried not using an object group and just putting the rules in the access list. I want to be able to add to these rules if needed easily.
I think it's clear that i have exceeded the rule limit for the ASA. So my question is, what is the rule limit for an ASA 5510 and which ASA could I purchase that would handle this amount of rules?
I've got some problem with my Mail Server since I've migrated to an ASA5510.Actually the server is in a DMZ with a private Ip ( 10.x.x.2) and it is translated to a Public IP ( 194.x.x.65).I use these configuration :
static (DMZ,LAN) 194.x.x.65 10.x.x.2 netmask 255.255.255.255 static (DMZ,LAN) 194.x.x.66 10.x.x.3 netmask 255.255.255.255 static (DMZ,WAN) 194.x.x.65 10.x.x.2 netmask 255.255.255.255 static (DMZ,WAN) 194.x.x.66 10.x.x.3 netmask 255.255.255.255 static (LAN,DMZ) 192.168.0.0 192.168.0.0 netmask 255.255.248.0
Some Users received in there mailbox a system administer error message :
Object : Impossible to deliver : test Your message could not be deliver to one or more of its recipients: 421 SMTP connection went away!
When they try to re sent it some times later, message is sent without problem.
I have a 5510 with just a inside and outside interface, everything works on the lan inc internet access and exchange hosting to the net, but I have another exchange server on the wan and I can't get to that because I'm not natting inbound traffic and the default route sends traffic elsewhere.
If I put a nat any statement on the inside interface inbound it works, however all LAN internet traffic fails with a No translation group found error.I've removed the static nat commands as they are all named anyway, but below is what I have before I do a nat any inside inbound command global (outside) 1 interfaceglobal (inside) 2 interfacenat (inside) 0 access-list inside_nat0_outboundnat (inside) 1 0.0.0.0 0.0.0.0.
I am getting the error "cypto map policy not found" when attempting to connect the VPN. My running config is below.I am attempting to connect from a draytek 2820.
View 5 Replies View Relatedwhen i connecting internet through my samsung c5212 phone it shows error 628.the remote computer terminate the connection
View 1 Replies View RelatedIf I'm outside my home network, I'm getting an error saying router is offline when i use the iPhone smart wifi app on my cellphone service LTE.When I connect using my home connection or wifi, I don't get the error and I'm able to connect to my router E3500.Why is this happening ?
View 7 Replies View RelatedMy printer has an error saying cannot connect to network......this problem occurred when i made a secure internet connection. I have tried resetting everything , unistalled printer software, i have changed all kinds of things on my router page . Apparently not the right things. I have a Dlink 524 router , Hp photosmart 5510 printer and 2 laptops.
View 1 Replies View Relatedmy Cisco ASA 5510 doesn't save the configuration to the disk.
View 1 Replies View RelatedI have turned on the aaa command authorization without applying adequate privileges to the user. I can now log in through that user but the ASA 5510 displays an error :ASA 5510# show running-config
ERROR: % Invalid input detected at '^' marker.
ERROR: Command authorization failed.
I am unable to make any configuration changes on the firewall. Is there any default user through which I can log in and disable the aaa authorization ? if not, how can I resolve this situation ?
i have a small asa 5505 trying to connect to a asa 5510
cisco-26834# sh crypto isakmp sa
Active SA: 1 Rekey SA: 0 (A tunnel will report 1 Active and 1 Rekey SA during rekey)Total IKE SA: 1
1 IKE Peer: 216.**.**.146 Type : user Role : initiator Rekey : no State : AM_CTCP_WAIT_REPLY
here's the full debug for the 5505 :
cisco-26834# Jun 30 03:35:26 [IKEv1 DEBUG]: IP = 216.**.**.146, IKE AM Initiator FSM error history (struct &0xc66a55b8) <state>, <event>: AM_DONE, EV_ERROR-->AM_CTCP_WAIT_REPLY, EV_CTCP_LINK_FAIL-->AM_CTCP_WAIT_REPLY, NullEvent-->AM_CTCP_INIT, EV_REQ_CTCP_LINK-->AM_START, EV_START_AM-->AM_START, EV_START_AM-->AM_START, EV_START_AM-->AM_START, EV_START_AM
Jun 30 03:35:26 [IKEv1 DEBUG]: IP = 216.**.**.146, IKE SA AM:c045cc52 terminating: flags 0x01000021, refcnt 0, tuncnt 0
Jun 30 03:35:26 [IKEv1 DEBUG]: IP = 216.**.**.146, sending delete/delete with reason message
Jun 30 03:35:26 [IKEv1]: IP = 216.**.**.146, Error: Unable to remove IPSec/TCP entry
[code].....
what should i check on my 5510 ?
I am facing problem connecting via vpn to my asa5510 using anyconnect.My anyconnect client shows "network access: unavailable - no networks detected" before i attempt to establish my vpn.Upon establishing vpn, i was prompted username and password which went through but i was given the error "anyconnect was not able to establish a connection to the specified secure gateway. Please try connecting again".I face this problem after replacing my pc. I was able to connect without problems on my previous pc.The vpn connection uses cert which i have already import to my new pc and authentication is fine since no authentication error. No changes made on my firewall.
View 1 Replies View RelatedMy roommate has just gotten a second hand laptop and he's trying to connect it to the Wireless network so that he can browse the internet from his room.However, although all the settings are correct, attempting to connect to the network loops.It comes up showing the Wireless Networks available, I select the network and click connect, it then asks for the encryption key. I enter the key and hit connect again, it comes up with the 'Connecting' pop-up and then loops back to the Available Networks screen again.There are no error messages, it just goes back to the starting screen and it hasnt connected.The Laptop in question is a Lenovo T60 with a Intel PRO/Wireless 3945ABG card.The router is a TP-Link TD-W8960N.
View 5 Replies View RelatedConnection denied due to NAT reverse path failure
View 2 Replies View RelatedI have a similar problem, I'm able to connect via VPN client and ping only one host on the remote lan and nothing else. I'm using both split-tunnel and non-split-tunnel, but none has worked. My main objective is to make the remote user connect to office lan (remote lan for him) and office Internet connection.
View 6 Replies View RelatedMy Linksys WRT120N router was working fine for all of 1 and 1/2 months and suddenly it stopped making the internet connection. At first nothing could access the internet but now that I've reset the router (via the little reset button in the back) my Kindle can access the wireless, but of course no password etc. I actually don't know how to put back the username and password for it. When router is connected: When I troubleshoot the connection by clicking on "Repair Connection" it takes about 2-5 mins "obtaining a new network address" then I get an error saying "The wired connection to your router was not automatically repaired. X Local network: Not connected.
View 14 Replies View RelatedMy xp computers recently gave up. So, I bought a new one (windows 7).
When I had my new computer plugged directly into my modem, there was no problem; I could easily connect to the internet.Yet, when I plugged the modem into my router (WRT54GS) and then plugged the router into the computer, I repeatedly encountered: Error 651.
The new computer has a built-in wireless adapter. So, I was able to disconnect the router and try to re-connect via a wireless connection. Yet, dispite being able to connect to my "network", the computer was not able to connect to the internet; again, I received the dreaded Error 651 message.I tried using the installation disk, but it would not work, either.
