I have a 5508 WLC running on 7.0.116, I need to be able to pull all configured users off the WLC and import into excel, I have 900 odd users configured. When I run a show net user summary it only displays a third of users. I'm hitting space to tab through each page, then eventually I just get dumped back to the command prompt.
View 5 RepliesI have two MLS conected by 2 fast ethernet links f0/11 and f0/12 on both sides.I am trying to set up a layer 3 etherchannel using these two links . But when i see etherchannel summary, they dont show up as layer 3. Instead they show as layer 2.
View 19 Replies View RelatedAnyn equivalent command of show etherchannel summary for a 10008 router running 12.2(33)SB9 ?
View 1 Replies View Relatedtell me if there is an equivalent command to Show int Summary on the Nexus 7000?
eg
MYCISCOSW01#show int summary
*: interface is upIHQ: pkts in input hold queue IQD: pkts dropped from input queueOHQ: pkts in output hold queue OQD: pkts dropped from output queueRXBS: rx rate (bits/sec) RXPS: rx rate (pkts/sec)TXBS: tx rate (bits/sec) TXPS: tx rate (pkts/sec)TRTL: throttle count
[code]....
I find it a useful command on the 6500 to spot high traffic flows.
What is the OID for the count of the APs connected (and Status UP) to a WLC 5508?
View 2 Replies View RelatedI have copied status codes from show ip bg command output and its explanation (from Cisco documentation site)., d and h (suppressed, dampened and history). I read somewhere that these are to control flapping routes. But not able to understand it completly.Raised this question in a couple of forums but didnt get a proper reply.The table entry is suppressed.??The table entry is dampened. ??The table entry history. The table entry is validThe table entry is the best entry to use for that network.
View 2 Replies View RelatedIn a basic VPN l2l scenario using ezVPN, server behind NAT device, client using 3G. What would be the reason to have in the output of the show crypto ipsec sa, a current peer different from remote crypto endpoint on the server ?
View 3 Replies View RelatedThere're more than twenty 6509VE running in the network. All of them has got 1GE or 10GE SFP / GBIC.However, when I tried "show int trans" in some of them, there's nothing shown:
Router_A#sh int transceiv
No transceiver present
Router_A#sh inv
Router_A#sh int status | i connected
Gi1/1 connected 304 full 1000 1000BaseSX
Gi1/2 To WLC5508 connected trunk full 1000 1000BaseSX
Gi1/3 To WLC5508 connected trunk full 1000 1000BaseSX
[code]....
I've multiple FWSMs running. The funny thing: When I do a "show resource usage" I have one blade showing a "Conns [rate]" and "Syslogs [rate]" values and one blade isn't.
SSH 4 5 15 0 admin
Syslogs [rate] 1 437 unlimited 0 admin
Conns 149 23465 unlimited 0 admin
Xlates 154 2877 unlimited 0 admin
Hosts 154 2877 unlimited 0 admin
Mac-addresses 6 7 65535 0 admin
All modules are running the same software version 3.2(10).And the even more funny thing is: on one blade I have different output for all the contexts on it.What's the reason for that behaviour? A bug?
How to approach an overnight upgrade from autonomous AP1231/1242 deployment into a 2504 controller-based AP1602 deployment.I do not have access to the existing 1231/1242 deployment ==> I need to ask network manager for all necessary config info to be ported onto the 2504.Example: the 1231 show run output does not list the various SSID that are in use.Therefore the question is: which commands' output do I need to ask to have all possible config data from 1231/1242 to use when configuring the 2504/1602 deployment.
View 2 Replies View RelatedI have a cisco ASA 5505 . I need to store " show capture 'word' ( where is a variable) output to syslog server for analyzing packet and port .
View 2 Replies View RelatedI recently configured a network with a 4500 Sup7E and a 3560G with jumbo frame support. I am trying to confirm operation. On the 4500 this is straight forward using "sho int g0/nn count detail". [code] The 3560 doesn't support that command. The closest I can come to finding the number of jumbo packets is "show controllers ethernet" (example below). On the transmit side I assume that jumbo frames would be tallied in the "Too large frames" counter. The receive side is a little more ambiguous. There are 2 counters that seem to be duplicates, "Valid frames, too large" and "Valid oversize frames". In operation they are not. I am seeing the "Valid frames, too large" counter incrementing while the "Valid oversize frames" remains at zero. [code]
View 0 Replies View RelatedI have a really weired thing happening on 6509 device with one of my customers.The device has a SUP 2 (MSFC2) with version 12.2.18SXF17B.
any VLAN interface once administratively down or simply down shows on "show interface status" output as VLAN.While it supposed to show "Routed". However once the port is up it is shows "routed" like it should.
I am trying to get a sample command output of "show chassis inventory" for:
CSS 11501
CSS 11503
CSS 11506
Working on setting up a Cisco 10008 with PPPOE and it seems like we kind of have it working but only one user can get on.
Here is part of the config:
Cisco-10008#show run
Building configuration...
Current configuration : 4134 bytes
!
version 12.2
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
service password-encryption
Also is there a way to show a specific user once they are connected with PPPOE? I'm currently using "show aaa sessions", but was thinking it would be "show pppoe something"
I'm setting up a new SF-300-08 with SNMP.I have defined Groups OK.But, when I go to Add User, the Group pulldown is grayed out and I can't add a user.
View 1 Replies View RelatedI would like to know whether there is any command that shows the configuration of the wireless controller (5508) like when you upload the configuration file from the GUI of the WLC. In other words, I don't want to show me all the verbose running configuration as the "show running-config", but a brief configuration as for example described below: [code]
View 2 Replies View RelatedWe are running in our DC one of the CISCO 2911 terminal server which is connected with HP ARC sight logger.
it is possible to capture user who execute ‘Telnet” or “show line” in the log, I mean all the command entries by user.
How to enable any config on 2911.
Just replaced a 2106(ver 5.1) with a 5508 (ver.7.2)...Everything was OK.. AP's got on 5508 and we shut the 2106. (AP's are on L2 with controller)During some investigation of why new LAP's from a location via VPN/GRE don't show up in controller, i type the following command on 5508: test ap pmtu enable all....All AP's on 5508 is now in Not Joined state..Have powered up the old 2106 and put AP's on that .. This is OK ....Have rebooted/downgraded/upgraded the 5508 controller but with same result.....No AP's can join this controller (exept from a oeap600)
View 8 Replies View RelatedI am configuring my 5508 WLCs with SW version 7.0.116.0. I configured a guest ssid with web-authentication enabled, but I cannot retrieve the login page on the controller. I configured the virtual interface with the addredd 1.1.1.1 SSID Layer 2 security: None SSID Layer 3 security: Web Policy enabled
I join the ssid with clients, receive the IP address correctly however when I try to open a web page, the login page does not appear. When I check the client status I see that it stuck in WEBAUTH_REQD state.
We got a question about our WLC 5508 single controller deployment with 14 access points without a VLAN configuration.
When our clients connect to the wifi, we cannot see any ip address of them in the client details page. It shows everytime the ip address 0.0.0.0. The clients are configured with a static ip.
I was having users on a Cisco WLC 440x controllers. Some service accounts were logged several time with the same AD-Account.Since I migrated them on the new controller (5508), it seems that we cannot have the same AD user logged several time.
I changed the Radius server with the one we were using on the old 440x but situation seems to be same,I checked the error message when trying to start a second similar connection they looks like :
*Dot1x_NW_MsgTask_4: Aug 24 14:04:51.558: %DOT1X-3-MAX_EAP_RETRIES: 1x_auth_pae.c:3062 Max EAP identity request retries (3) exceeded for client xxxxxxxxxxx
*Dot1x_NW_MsgTask_4: Aug 24 14:04:51.558: %DOT1X-3-ABORT_AUTH: 1x_bauth_sm.c:447
Authentication aborted for client xxxxxxxxxxx
If I move back to the other 440x similar logins are allowed without any problems.
I have a user authentication issue with our WLAN deployment. My issue relates to the guest access WLAN. First a brief descrition of our setup. We have a local WLC in the branch office (5508) with two SSIDs configured, CorpNet for the internal network and GuestNet of external guest access. We also have a WLC (5508) in the DMZ to provide the guest access. We are using Cisco ISE server to authenticate guest users via a web portal.
The authentication process works as it should. An external client gets an IP in the DMZ and is redirected to the web portal to authenticate their account. When they do they are able to access and browse the internet. No problems. My issue is that if we disable their account (ie suspend or delete it) in ISE it does not seem to terminate the users session and they can continue to have internet access. What I would like to happen is that when the account is disabled in ISE then the associated device's access to the internet is removed.
I'm on WLC 5508 . It doesn't matter if passive client feature is turned on or turned off , when you try to increase "User Idle Timeout" you can see this message:
In our network, a lot of clients gets deauthenticated. I thought it would be useful to enable "Passive-client" feature, or increase "user idle timeout" , but how these works with each other?
In my Wireless network, I have two appliances WLC 5508 running version 7.0.116.0.I have a WCS running version 7.0.172.0, deployed on a windows 2003 server.I've imported the two WLCs in my WCS in order to centralize the monitoring and the configuration tasks.Now I'm facing an issue when I want to create a guest user from the WCS, rather than creating this user access on each WLC. The creation of the user account is working good, the replication is done on the both WLCs, but on one of my WLC the guest user account is deleted after one hour(around).On the second WLC, the same user account remains during all its life time.In attachment a screen shot of the advanced parameter of the guest user.You can see that the user was created on the both WLC but is only active on one ... and unfortunately the wrong because the AP is associated with the other WLC.
View 2 Replies View RelatedI've got a WLC5508 (7.0.116.0) that is managed by WCS (7.0.172.0). I set up another WLC5508 with the same code and managed by the same WCS. Now I'd like to export all the 800 guest user accounts with the passwords from the old WLC and import them into the new WLC.
View 10 Replies View RelatedI am running a guest wireless network on a Cisco 5508 WLC with 6.0.202.0 code. My syslog is filling up with the following error message:
WLC: *May 15 12:32:59.244: %AAA-3-VALIDATE_GUEST_SESSION_FAILED: file_db.c:3968 Guest user session validation failed for guest_user10. Index provided is out of range..
The user that is assigned to the guest_user10 account works fine and has no idea this error is occurring.
This error message is occuring exactly every 15 minutes 24x7.
I believe I have a rogue user who has setup a device to try and login to the guest network automatically, every 15 minutes with the guest_user10 credentials. I need to track this device down. I need a way to find either the MAC or IP address of the device that is causing this error message. I have tried turning on AAA debugging on the controller but I dont get anything more than the above error. I have also tried using WCS to look at the client history but it only show the normal activity.
I just get to hands-on on my new WLC 5508?
1) I'm using a single subnet eg 192.168.1.0/24 for my wireless clients and i'm assigning them via the DHCP server from the WLC. As the clients are however made up of laptops and scanners, i would like to assign a range from 50-150 for the laptops and 151-250 for the scanners for easier identification. But it seems that from the WLC DHCP menu i'm not able to do this unless i segment them into a different network with different gateways.
2) Is there anyway to change the WLC user accounts password too? I dont seems to be able to find the option unless i delete the account and re-create it with the new password.
how to set WLC 5508 to allow single create web authentication user account to get connected in a same time. i found that i can use the same username and password combo to be login in 2 machine in the same time.
View 4 Replies View RelatedI work at a campus and use the WCS to control access to my network for staff and only internet access for students. The Staff are assigned Username/password thru active directory and the student uses another SSID with only WPA --a password for all. I was tasked with adding more securing for students -- by adding a user/password. I do not want them connecting to my Active Directory for two reason--security risk and I have too many to input (over 1000). So, I wanted to use our internal database to validate users. I create a webpage with "WebAuth" that opens my logon page from my site and validates the login fields against the database. It works and this allows the user to navigate thru my website but not outside the site. If they try an outside url it redirect them to my logon script. I now understand why, so I'm looking for code I can add to my logon page that would allow me to redirect me to the controller's (once users are authenticated by my database) to call the WCS controller so I can enter a preset username/password so the policy management file would allow them access. I presently use "External" and don't know if "Custom" would work. Finding a way in using a database instead of adding one person at a time?
View 3 Replies View RelatedThis first started when a user said they were getting disconnected and reconnected a few times a day to our wireless network. He is in a remote office with a 1142 which is set to H-Reap talking back to our 5508. Our WLC is running 7.0.166 The laptop has an intel ulitmate 6300agn wireless card with the latest 15.x drivers.
We are using an SSID with wpa2 and 802.1x auth back to our ACS server using PEAP with our windows credentials.attached is what i am seeing on the wcs troubleshooting page.When i do a debug client on the WLC i see many reauthentications coming from the client on the different radio.
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Reassociation received from mobile on AP 0c:85:25:f3:7d:40
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c 10.24.8.108 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying site-specific IPv6 override for station 00:24:d7:d1:16:6c - vapId 512, site 'VH-GasWorks', interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying IPv6 Interface Policy for station 00:24:d7:d1:16:6c - vlan 2, interface id 0, interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Applying site-specific override for station 00:24:d7:d1:16:6c - vapId 512, site 'VH-GasWorks', interface 'management'
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c 10.24.8.108 RUN (20) Changing ACL 'none' (ACL ID 255) ===> 'none' (ACL ID 255) --- (caller apf_policy.c:1621)
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c STA - rates (8): 140 18 24 36 48 72 96 108 48 72 96 108 0 0 0 0
*apfMsConnTask_2: Aug 22 12:59:36.762: 00:24:d7:d1:16:6c Processing RSN IE type 48, length 38 for mobile 00:24:d7:d1:16:6c
[code]....
Now this may be not be the issue thats causing our dropouts a couple times a day as this is happening every 5 mins.
I have 5508 controller in my lab. I am working on a project to set up a public internet but with some condition.
- User should able to connect to the SSID without any authentication.
- Once user will connec to the SSID it should redirect to an external URL which indicates terms and condition and email address field.
- User should enter his/her email address in email addrss filed and click I accept button.
- Once that is done then he/she is allowed to access internet.
We are not sure how can we achive this as I do not know what should be the return value for WLC to allow that user to go through or what should be the settings on the WLC to redirect to the page.
I have seen a settings on web authentication for external URL but I guess it is only for username passwor or Radius authentication. While in this case I do not want to use any authentication just an accept buttor or Decline button and all good to go.
When a guest user first trys to access the "guest" WLAN, they are presented with a "certificate page" before the web athentication page / login is presented. The WLC forces an internal redirect to https://1.1.1.1 causing the certificate page to appear. Can this be bypassed? I am runiing 5508 with 7.0.220.0.
View 12 Replies View Related