Cisco :: 5508 - Web Authentication Login Page Does Not Show

Oct 21, 2011

I am configuring my 5508 WLCs with SW version 7.0.116.0. I configured a guest ssid with web-authentication enabled, but I cannot retrieve the login page on the controller. I configured the virtual interface with the addredd 1.1.1.1 SSID Layer 2 security: None SSID Layer 3 security: Web Policy enabled
 
I join the ssid with clients, receive the IP address correctly however when I try to open a web page, the login page does not appear. When I check the client status I see that it stuck in WEBAUTH_REQD state.

View 16 Replies


ADVERTISEMENT

D-Link DIR-825 :: Login Page Doesn't Show Authentication Picture

Nov 29, 2011

i have a dir 825 with fw 2.00eu that i wanted to upgrade to the new beta fw.i went to tools and did a factory reset first,when i wanted to log back in to load the new fw,it sudenly asks for a authentication code,problem is the field is marked with a red x so i cant see any code i'm using windows 7 and IE 9?

View 5 Replies View Related

Linksys Wireless Router :: E3000 Sometimes Don’t Show The Login Page For Guest

Aug 11, 2011

I have an E3000 with firmware version 1.0.04 with WiFi configured as:Guest5GHz (only N)2.4 GHz (only G)I use the guest network access for my guests or my neighbor.Usually they connect and the first page they see in the browser is the http://192.168.33.1/login.asp were they put the password. Some times shomething don’t work and the browser don’t show the page, so the people can’t use the connection because they get a timeout error.The only solution I have in this case is to resart the router, but sometimes is not enough and I have to fisically shotdown and restart it.The login.asp page starts with: This is UNPUBLISHED PROPRIETARY SOURCE CODE of CyberTAN Inc. the contents of this file may not be disclosed to third parties, copied or duplicated in any form without the prior written permission of CyberTAN Inc. This software should be used as a reference only, and it not intended for production use! What about a firmware update to fix it and give the control from the web administration over the guest network?

View 5 Replies View Related

Protocols / Routing :: Successful Login Redirects Back To Login Page After Satellite Upgrade?

Feb 10, 2012

I have a website account with fatcow. I created the website with Dreamweaver software and uploaded it to fatcow via port 21.My internet connection was via xplornet and I had no access problems. I upgraded to xplornet's new g4 system and now I can no longer access my account online or upload to my website.We have two computers. The first is a desktop system that has the dreamweaver software. The second is a laptop which connects wirelessly. We share the signal through a dlink router. The modem is a viasat Surfbeam 2 residential satellite modem.1. When I attempt to login to the fatcow control panel, the tab shows successfully authenticated and then re-directs me back to the login page. This happens on both the laptop and the desktop.

I have tried bypassing the router and the problem still exists.I took the laptop to the computer center and I can login to the account no problem.I used a free proxy server page on the internet and can login from my home system on my desktop no problem.I have completely turned off virus scan and firewalls. It doesn't work. I have tried IE7, Chrome, Firefox and they all have the same problem. The laptop runs IE8 and has the same problem.I can ping the page successfully. I can traceroute the page successfully. I can't nslooup any site at all. I get the domain not existant message.My ip and dns settings are the automatically find option.I have renewed ips and dumped the dns cache.Using alternate dns addresses doesn't rectify the problem. When I attempt to upload via dreamweaver, I connect but within seconds I get a Dreamweaver message that says "Connection to remote host has been lost. Click refresh to continue" and the log reads "FTP Error. Dreamweaver could not connect to server." I haven't taken my desktop anywhere to try to see if it works on a different network. I'm in a remote location (hence the satellite internet)and it is an hours drive to the nearest private internet connection and a 2 hour drive to the nearest public connection.

View 19 Replies View Related

Cisco :: Can't Get To Home Page When Login To LMS 3.2

Sep 4, 2012

After clearing the Browser-Cache I cant get to the Home page when I login to LMS3.2. Instead of the Homepage following is showing: NOT FOUND Unable to find URL. The selected View has been deleted or Friendly URL has been modified.

View 1 Replies View Related

Wireless Network Won't Show On Connection Page?

Nov 10, 2012

I can't find my linksys network on the "wireless networks" I've been able to use it many other times but just this past week it hasn't been showing.

View 1 Replies View Related

Cisco VPN :: Customize Login Page For ASA 5505 SSL?

Nov 1, 2012

customize the login page for the ssl-vpn as mentioned. When the vpn is set up, the default template allows my customers users to login with this : IMAGE 1
  
While trying to edit the login page, I have to create a new Customization file from CLIENTLESS SSL VPN ACCESS -> PORTAL -> CUSTOMIZATION in the ASDM. When I do that and I try to edit the login page, it comes up with 2 forms of authentication and an internal password prompt like this: IMAGE 2
 
How can I edit the login page I created so that users will only see the regular username and password fields like the default template?

View 2 Replies View Related

Cisco VPN :: ASA5510 - SSL Login Page Does Not Display

Jan 21, 2010

I have an ASA5510 that I am trying to set up for remote access using SSL VPN & clientless SSL VPN. I have followed the config guides on the Cisco website as well as the config guides elsewhere on the internet to no avail. I have a TAC case opened and have spoken with 4 engineers thus far. I have tried several software versions on the device and they all give the same result.When going to https://(outside interface ip address), I receive the expected ssl certificate error, then I click to continue to the website, and the browser never loads a page. I can see the ssl negotiation in my debug, and it completes that portion. My http debug shows the get requests to https://(outside interface ip address)/+CSCOE+/index.html and/or logon.html, but the page never loads.

View 7 Replies View Related

Cisco :: ACS 5.1 Access Is Denied To NCS At Web Login Page

Dec 11, 2011

I configured my ACS 5.1 correctly, but I get an "Access is denied to NCS" at the web login page. In the ACS i see a successful authentication.

View 14 Replies View Related

Cisco :: W2k8R2 - LMS 4.1 Blank Page After Login

Jan 29, 2012

I recently installed LMS 4.1 on a freshly installed W2k8R2 server, and untill last week I had no problems logging on. For some reason, I'm now getting a blank page after entering my credentials. The URL is like [URL] I already rebooted the system, but that made no difference. All Cisco Works services seem to be started, as is Apache/2.2.17.

View 1 Replies View Related

Cisco WAN :: Unable To Use WLC 3750G Login-Page?

Jan 22, 2012

I have a WLC 3750 and use the web authentication method with the internal login-page. Now I would like to add a link to a PDF document which is supposed to be available before logging in. In other words: Clients connect to the W-LAN and get access to the login-page. They can download the PDF document (which has by the way a size of ca 10MB) from the login-page and after that they login to get access to the internet.
 
As far as I understood the manuals I won't be able to use the internal login-page because the size of a file is not allowed to be bigger than 1MB.So I thought about using the external authentication by using the webserver of my website. Unfortaunely the IP-Adress of my website doesn't work. Behind this IP-adress there's more than one website hosted. So I can't use my webserver either ...
 
Is there any other possibilty to add this PDF (size 10MB) on the login-page? Maybe I can add my website to a kind of a "pass through list" which is accessible even without authentication?

View 11 Replies View Related

Setup Wifi Login Page?

Jun 9, 2012

I want to do a logging in page for wifi network ,I use IIS to host my page , ASP.net as the page designer and I think but I'm not sure yet that I make my PC work as a gateway by enabling IP ROUTER form the registry ,now what I need is how to make that page available in all wifi users web browsers except the users they logged in ?

View 1 Replies View Related

19216811 Linksys Login Page?

Aug 29, 2012

i want to stablish a new internet connection through bsnl broad band tell me hou i can install and run internet.

View 1 Replies View Related

D-Link DIR-655 :: Login Page Cannot Be Found?

Jan 7, 2012

typing 192.168.0.1 just times out when there no internet connection problem.  I can go into my modem settings through.   I don't know when this problem started as I hadn't needed to log into my router in over a year.  I tried resetting it and still can not go to the log in page.  I noticed a few months ago my NAT type went from open to strict on my xbox live but didn't really care at the time

View 10 Replies View Related

Cisco AAA/Identity/Nac :: Banner For ACS 5.3 Admin Login Page

Feb 20, 2012

Is there a way to put a login banner on the ACS admin web page?  Either display it directly on the web page or do a redirect to a banner page?  Can I edit the admin pages directly or does ACS provide a mechanism to add this type of feature?
 
We are using ACS 5.3 running on VMWare.

View 2 Replies View Related

Unable To Login Into Router Config Page

Feb 4, 2013

Basically all I want to do is login to my routers config page so that I can forward ports. I was able to this a few weeks ago but recently I have received this error. Failed to connect

Things that I have already tried:

- Tries using 192.168.0.1, 192.168.1.1, http://192.168.1.1 and all kind of variations.

- Tried with different browsers.

- Tried with seperate computer with different OS's (Mac and PC)

- Unable to flush dns because I get this error: CMD prompt error message .

- Have factory reset router a few times now.

- Unplugged, left off for 20mins-2hours.

View 16 Replies View Related

Creating A Login Page For Wireless Network?

Feb 25, 2011

I was in a pub the other day. When I tried to use their wireless I was directed to a webpage to enter the password.I am a web designer and want to make a funky login page, not for a user ID. Just to enter the password to my wireless.How do I do this? Im not aiming to make my system more secure.

View 1 Replies View Related

Cisco VPN :: ASA5510 / SSL VPN With Anyconnect Client - Login Page Does Not Display

Mar 18, 2012

I have an ASA5510 that I am trying to set up for remote access using SSL VPN with the anyconnect client. I have followed the config guides on the Cisco website as well as the config guides elsewhere on the internet to no avail. When going to https://(outsdie interface ip address),I get nothing, the browser never loads a page. Here are the commands I have entered:
 
webvpn
enable outside
svc image disk0:/anyconnect-win-2.5.3046-k9.pkg 1
svc image disk0:/anyconnect-macosx-powerpc-2.5.3046-k9.pkg 2
svc image disk0:/anyconnect-macosx-i386-2.5.3046-k9.pkg 3
svc enable
tunnel-group-list enable

[code]....

View 13 Replies View Related

Cisco :: LMS 4.0 Win2K8R2 64bit Blank Page After Successful Login?

Mar 7, 2012

I have a ticket active with Cisco TACS Support but after 3 days and a complete uninstall and reinstall I am getting nowhere. I cannot let TACS into the server and I cannot post unsanitized logs for security reasons.I installed LMS 4.0 with the Win2K8 patch on Win2K8R2 64 bit server. No problems during a 2nd install (first one was completely removed per TACS). Checked all Windows event logs and windows firewall log. AV disabled. No other roles installed accept IIS (disabled) and DHCP (active). Ports are default HTTP: 1741 and SSL: 443.load site from server (IE 8) or workstation (IE 7) cookies enabled, and login with "admin" and the proper password and each browser quickly loads a blank page with this URL:
 
[URL]
 
Apache error.log shows several interesting entries (*note IP and serer names are obfuscated for security)...these show up yesterday soon after install at the top of the log:
 
[Wed Mar 07 16:04:25 2012] [warn] RSA server certificate CommonName (CN) `<server_name_obfuscated>' does NOT match server name!?
[Wed Mar 07 16:13:04 2012] [error] [client IP_obfuscated] client denied by server configuration: C:/Program Files (x86)/CSCOpx/htdocs/favicon.ico
[Wed Mar 07 16:13:04 2012] [error] [client IP_obfuscated] client denied by server configuration: C:/Program Files (x86)/CSCOpx/cgi-bin/error/403.pl
 
Then these show up for the majority of the rest of the log between yesterday Mar 07 and today Mar 08
 
[Thu Mar 08 08:50:46 2012] [notice]
WARNING: Session Validation returns false
[Thu Mar 08 08:50:46 2012] [notice]
session is invalid for this URL.:

[code]....

View 3 Replies View Related

Linksys Login Page - Only Shows A White Screen

Jun 6, 2012

I go into my login page and all I see is blank. Just a white screeb. I have put in my IP address, I have no idea what I should do. I have been trying to fnd my password but the page has no login.

View 3 Replies View Related

Belkin N150 F9k1001V4 - Cannot Login To The Router Page?

Jul 12, 2012

I have just bought a Belkin n150 router. Connected it to my modem and PC and I'm recieving internet. Connected my phone and laptop and getting wireless.The issue, however, is that I cannot login to the router page. The login says to leave blank for default, but it gives me an incorrect password error. I have tried resetting using the button located above the power cable to go back to defaults, but I continue to recieve the error.

I have tried a all the other usual default passwords, password, administrator, admin, etc.I've gone through pages of google search results and found nothing. Have I missed something obvious or did Walmart sell me a defective router?

View 1 Replies View Related

TD-W8910G - Cannot Access Login Page Of TP-Link Router?

Jan 31, 2013

Whenever I enter 192.168.1.1 to access the login page of my router, I cant access it to configure it even after resetting it !I also tried changing TCP/IP settings to static as mentioned in the router's manual but it dint work?

View 4 Replies View Related

Linksys Cable / DSL :: X3000 - Can't Login To Account Page

Feb 14, 2012

We set up our new Linksys last night but when the password was written down there is no distinction between upper and lower case letters - I can't login to an account page or do anything and I needed a password for a visiting friend.

View 1 Replies View Related

Linksys Wireless Router :: E4200v2 - Smart Wifi Cannot Show Anything After Login

Mar 18, 2013

I've just updated my router (E4200v2) to the smart wi-fi firmware and it seems I can only properly access it in the "local" mode (by that I mean that I can edit some of the properties such as wifi settings).If I try to login through the cloud / smart wifi account i only get the empty screen, no options, no widgets, nothing (see the included picture).

View 5 Replies View Related

Cisco VPN ::ASA 5550 / Default Connection Profile On WEBVPN Login Page

Jul 5, 2011

I have a pair of ASA 5550s running Anyconnect Essentials, with multiple connection profiles configured. I would like the login page to the portal to default to our main corporate profile (so the users get NAM and all the policy goodness), but presently it is defaulting to the last profile I created.  Is there any way to modify the default connection profile in the drop down list so it always defaults to my preferred profile? It seems like I saw this sometime in the past. 

View 2 Replies View Related

Reset Motorola SBG901 Router - Now Can't Access Login Page

Feb 21, 2012

I have a Motorola SBG901 router. Typing ipconfig showed that 172.18.8.1 is the Default Gateway and this is the URL I always used to access the router login page.

I reset the router today by holding the reset button. Now typing the URL 172.18.8.1 does not work. The router user guide says to go to 192.168.0.1. I have tried this but it also does not work. For both I just get the "problem loading page" in Firefox.

The Internet works fine both with an ethernet connection and wirelessly. My only issue is that I cannot access the Motorola router login page. I could access it fine this morning before I reset the router.

View 6 Replies View Related

Linksys Wireless Router :: EA-4500 Can't Login Into Setup Page

Oct 26, 2012

I'm trying to login to my EA4500 setup page. I have the "cloud connect" firmware and when I'm redirected to the "Linksys Smart Wi-Fi" page in my browser, I attempt to login as usual.It accepts my login name and password, and then I get a page that has a rotating graphic and it says "waiting..." It eventualy times out and takes me back to the login screen. I've tried to reboot my router and that doesn't work. I've also disconnected the internet connection from the modem, and entered the router main password, and that gives me the same response as if I tried to connect via the cloud.

View 9 Replies View Related

Linksys Wireless Router :: Changing Look Of Welcome Page (guest Login)

Feb 9, 2013

Is it possible to change the look of welcome page (guest login) to change so that it is personal. Of course it would be great if the guests have to log on your personal page.On this page you would be able to indicate the rules and  and limitations. It would also be a good option for certain that your guests a limited time duration for the connection and gives max download. This would also be found to be in a log.

View 2 Replies View Related

Linksys Wireless Router :: E1550 Getting Error And Could Not See Login Page

Mar 23, 2012

I tried to connect to my E1550 router admin page at 192.168.1.1 and I'm not seeing the login page. I'm getting an error. I've always been able to get to the admin page. I'm not sure what changed. I tried changing the IP# and subnet mask of my laptop and I still can't connect. I tried resetting the router to factory defaults.

View 1 Replies View Related

Cisco Routers :: RV042G Site Certificate Invalid On Admin Login Page?

Aug 17, 2012

I recently replaced my RV042 with an RV042G.  I did an export of the RV042 Config and used the Config Migration Tool to upgrade the file to v3 (I had an old v1 RV042).  When I first logged in to the RV042G it was quite happy and I imported the config file successfully.After installing the RV042G in my system it fired up and worked perfectly.  Unfortunately when I now try to log in via the web interface it comes up with 'Invalid Site Certificate' each time. I've tried importing the certificate but that does not work as it is flagged as invalid.All I can assume is I have either imported the origional RV042 certificate as part of the config or importing the config has corrupted the original RV042G site certificate.  I assume this is a generic issue and not specific to the RV042G as I have had this problem before but cannot remember how I solved it.The bottom line would be a hard reset and load all my settings manually but I can't spare the time just now.

View 2 Replies View Related

Linksys Wireless Router :: E4200 Will Not Open Guest Login Page?

Jun 11, 2011

When Im connected to the GUEST network and open the web-browser it will not open the Linksys guest-login page. Why?(latest firmware ver.1.0.01(Build10) installed)

View 9 Replies View Related

Linksys Wireless Router :: EA6500 Admin Page Hangs On Login?

Feb 3, 2013

I have been through three chat sessions on this without resolution and support tells me just to factory reset. After some time (weeks) after a successful local login to the admin page subsequent attempt to login just hang. After entering the admin password the page changes and says "Waiting" under revolving circles. It will sit there for over 1 hour. I have tried IE, chrome and firefox on Windows 7 and Windows 8 on three different machines and it behaves the same. Of course I have to go through this same process with the support people every time and every time they come to the conclusion that I have to do a factory reset. But so far Linksys denies that there is a defect.

View 9 Replies View Related

TP-Link ADSL2+ Wireless :: TD-W8961ND Can't Access Router Login Page

Apr 28, 2013

Region : UnitedKingdom
Model : TD-W8961ND
Hardware Version : Not Clear
Firmware Version : V.3
ISP : ADSL24

Using windows 7 and 8 on different machines I am unable access my routers web based set up.

I enter the usual "admin" and password in the login box. 3 goes and then get error message. or hangs on waiting.(connected to the router with Ethernet Cable). Could this be a windows based problem. I think it was ok on XP but that is gone now. Router is working fine but I just cant access it to alter any settings.

My 2 other spare routers which are not TP-link also have the same problem.

View 1 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved