Cisco Wireless :: Aironet 3502 Only Shows Wireless N
Mar 2, 2012
I bought a used Aironet 3502 (air-cap3502i-a-k9) on craigslist last week and the seller said it was set up for autonomous mode. It has ap3g1-k9w7- tar. 124-25d.JA, which does allow it to run without a controller. I know it's not the latest version, but without a service contract I'm unable to access the latest firmware. When I go into the web management console, it only shows wireless N, without letting me enable A/G. The product sheet shows it should do A/G/N - is this just a byproduct of putting the autonomous ios on a 3502, or am I missing a setting somewhere to enable it?
View 3 Replies
ADVERTISEMENT
Oct 7, 2010
I have a Cisco WLC5508 controller which I recently upgraded to software 7.0.98.0 because I tried to add a Aironet 3502 and it gave me an invalid software. After the upgrade this is the error I get from the AP when I try to add. [code]
View 5 Replies
View Related
Nov 14, 2012
I have a Cisco Wireless LAN Controller AIR-CT5508-K9 running Software Version 7.0.98.218. This WLC has registered ten AP model 1240.Now I have configured fiive CAP3502 with static capwapp commands, when I connect the CAP-3502 in the network, in the WLC I see the status "downloading" then the CAP restart, and the console show the message *Mar 1 00:15:39.033: %CAPWAP-3-ERRORLOG: Could Not resolve CISCO-CAPWAP-CONTROLLER, and never the CAP3502 is registered in the WLC. [code]
View 1 Replies
View Related
Feb 8, 2013
i have 2504 controller with 7.0.116.0 software and some 3502 APs. I also using 5 APs now and few days ago I bought some additional 3502 APs and I can't get them connected to the controller. My company admins decided to using DNS controller discovery instead of using DHCP option 43. I'm connecting APs to access ports of Linksys switches and APs not in the same subnet as ap-manager interface of controller. AP succesfully get IP and DNS from DHCP and could ping cisco-capwap-controller. However, I have such messages.
*Mar 1 00:12:32.014: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP.Not in Bound state.
*Mar 1 00:12:40.533: %CAPWAP-3-ERRORLOG: Invalid event 38 & state 2 combination.
I can succesfully ping controller from AP AP30f7.0d2e.9a58#ping cisco-capwap-controller Type escape sequence to abort.Sending 5, 100-byte ICMP Echos to 10.23.16.30, timeout is 2 seconds:
View 6 Replies
View Related
May 12, 2012
There are a total of 25 Cisco 3502 APs installed. 24 APs were discovered except for 1 AP. I run SH CDP NE on the switch and the AP was discovered by the switch but it does not have an IP address. On the output of the SH CDP NE DE, I noticed that on the AP that is not joining, the Platform is "cisco AIR-SAP3502E-E-K9" while the APs that joined the WLC, the Platform is "cisco AIR-CAP3502E-E-K9". The software versions are also different but this could be because the WLC already upgraded the IOS when the APs joined.Why is the Platform "SAP3502E" for the AP that did not join.
View 9 Replies
View Related
Apr 2, 2012
Just a basic question regarding MAC based authentication of AP with ACS. The scenario is - If I have a ACS installed and I want all my Cisco 3502 APs to be authenticated on MAC basis via ACS. I know that AP mac is used as a username and password at ACS so that whenever we plugin the new AP in the network, it gets authenticated via ACS first and if the AP is authorized to be used in network then only it gets the IP address from DHCP.
My question is - What will happen, if the AP is connected in local mode on a remote location and the WLC, ACS & DHCP are in Data center. The traffic coming from remote location will pass through the Remote-site router and during that pass, it will remove the source mac address of AP and put the router interface MAC address as source, so how will the ACS authenticate the AP in that case.
When working in a LAN I know its possible, but how will it work over the WAN.
View 9 Replies
View Related
Mar 15, 2012
Using WISM with 7.0.220 and 1240 and 3502 APs. Just found that some of our 3502 AP didn't enbale their clean air and CDP when installed. This only happened on a few new APs. But the area these APs where we seem to have had a few problems with PCs. The only PCs effected where Computer On Wheels (COWs), Dell 780 Desktop with a Cisco Wireless Card.
Using an interl wireless card and others in thes areas worked.Once I enabled the CDP and Clean Air, the COWs worked.My question is with the APs not having CDP enabled, could this affect the cisco wirelss card in the COWs?
View 6 Replies
View Related
Jan 27, 2013
Our newly installed WAP's are constantly downloading code and seem to lose contact with our wism 1 version 7.0.235.3, causing them to restart the downloading process, over and over.
View 12 Replies
View Related
Jan 31, 2012
We have a secure ssid and a guest ssid. Is the a way to prompt for a single username and password and if that name is guest it will automatically connect to the guest ssid? If active directory user and password it will automatically use the secure ssid? we are using Microsoft NPS/Radius, 3502 ap's, and 5508 controller.
View 3 Replies
View Related
Aug 9, 2012
I found the 3502 waps are plenum rated, I found the cable on the antenna are plenum rated, but are the antenna plenum rated?
AIR-ANT5160NP-R?
AIR-ANT2451NV-R?
AIR-ANT2460NP-R?
View 8 Replies
View Related
Jul 5, 2012
I have one 5500 and about 15 Cisco 3502 APs.
The problem is that one of the clients loses the connection to the network time to time ,The error in the WLC logg is
*Dot1x_NW_MsgTask_0: Jul 06 17:42:38.934: %DOT1X-3-INVALID_WPA_KEY_MSG_STATE: 1x_eapkey.c:843 Received EAPOL-key M2 msg has invalid information when mobile is in START state - invalid secure bit; KeyLen 24, Key type 1, client 00:21:6a:af:be:70
View 4 Replies
View Related
Oct 19, 2011
I have got a 3502 setup and functioning in Office Extend mode. I have found one issue though. I have to set the checkbox on the my Management Interface to Enable NAT Address and put the external address in the box. Once this occurs no internal APs can join the controller.
Need setting this up with a single controller behind a router and not having to set the NAT Address for the Management interface? Should I setup a second interface on the controller to be for external management?
View 9 Replies
View Related
Mar 5, 2013
I have a 3502 AP that I am attempting to set back to factory default including clearing the username and password. It is going to work off of 4400 controllers. I have read numerous documents no how to clear the config and password but so far nothing has worked. I can get it into ap: mode but not sure what to enter here. When I do a dir there doesnt seem to be any files. It will pull an IP address via the local router but cannot communicate with WLC.
View 28 Replies
View Related
Feb 7, 2013
I am trying to configure a 1242 or 3502 WGB with PEAP. There is not ACS server involved as Windows RADIUS is used. I can get the WGB to work with OPEN Authentication but when I attempt to add in the authentication/security piece I get "no association." Below is my current config. The WLAN is set to use WPA/WPA2 802.1x + CCKM.
Current configuration : 1812 bytes
!
! Last configuration change at 00:56:39 CST Tue Mar 2 1993
version 15.2
[Code].....
View 1 Replies
View Related
Sep 25, 2012
We have installed a number of Cisco Wireless 3502-07 in China and i can not get the Clean Air Oper status to change to UP. At the meoment i have ERROR. I have have tried to disable and enable the the Clean Admin Status from the Access Point 802.11b/g/n and then select the AP and change configuration.
View 2 Replies
View Related
Oct 24, 2010
I am trying to locate the radiation pattern for a 3502 with an internal antenna. We have some high ceilings so the elevation pattern could impact our placement strategy.
View 6 Replies
View Related
May 20, 2012
I recently upgraded our controllers to the latest version 7 software, as I read this was one of the requirements to get them to connect. But I am not having any luck getting into a controller. Normally I plug them in to the network, they pop into the controller listed as something like AP5057.a844.xxxx and then I can finish configuring them, but a static IP on them, etc. This is the first of this model AP I have tried to deploy, so I am wondering what is different with these. or what I might be missing in the default config in the WLAN controllers. Niether of which are set to "Master" either.
View 10 Replies
View Related
Jul 30, 2012
We have been deploying 3502 APs remotely to locations with full T1s that backhaul to where I sit at HQ. Both the foreign and anchor controller are here at my location.
I am seeking to rate limit per user the bandwidth each client will get on the guest internet ssid. As you know this traffic is encapsulated in capwap between the AP and the controller so I cant use a standard ACL on the switch or router.
We are trying to keep the guest internet access usage in check on the T1 at any given site so the other ssid's & local lan traffic is not overly competing for the bandwidth.
I found the place to edit the default profiles in the controller but the documentation really isnt clear on best practices.
So I put it to you my fellow wireless engineers to suggest how you are implementing bandwidth management on your wireless guest internet.
Oh and here is my hardware & software levels.
5508wlc - forgeign
4402wlc - anchor
Software Version7.0.230.0
View 3 Replies
View Related
Oct 15, 2012
I Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies
View Related
Feb 22, 2012
I have a 4410N set up on my network. I'm using 4 VLANs on my network, of which, I use my default VLAN 1, as the "public" VLAN which we use to give our clients free WiFi. I would like to have two SSIDs visible from the access point, one unsecured and connected to VLAN 1, and the other secured with WPA2 and connected to our office VLAN on which various servers and resources are available. My preference is for both SSIDs to be visible, as there is not a major security issue and as the only IT person, I do not have time to configure every computer which uses the network with the SSID, but I'll do that if I have to.
I set up the 4410N with it's first SSID using our public WiFi name and did not put any security on it. I went to the VLAN page and set it to use VLAN 1 as both the default VLAN and the VLAN for the first SSID. Then I went back to the Basic Settings page and added a second SSID and chose "Enabled". I went to the Security page and left most things as default (Wireless Isolation between SSIDs is enabled) and changed the security settings for the office SSID to WPA2-Personal. Finally I went to the VLAN page and set it's VLAN to 4.
When I go back to my computer, or from other wireless devices, I only see the public SSID, not the office. I do see on my computer (Win7 x64) an "Other Network" option, but the signal strength on that network is significatnly weaker than that of the public SSID. Also, if I try to connect to it using the office SSID name and the password I set, it doesn't connect.
Am I completely misunderstanding how multiple SSIDs are supposed to work? I am working from a lot of assumptions here.
PS I have no clue if this would affect it, but in the interest of listing all possible factors, the 4410N is powered via PoE and the switch port it is connected to is set to 802.1Q with 1-4 set as the VLANs.
After posting this I discovered that in the Wireless Status page, both SSIDs are listed, but only one (the public SSID) has a MAC listed. I assume I need to add one somewhere. Where should I do this, and what's a "safe" MAC to use that won't conflict with anything?
View 3 Replies
View Related
Jan 12, 2012
I have 6 of the 1252 APs that suddenly no longer will associate with any of my 3 4400 controllers. I've verified the power injectors are up and good, shut the port on the switch, and even moved from one power injector to another. Also, in WCS there is a picture of what looks like 3 disks stacked on top of each other, and I don't know what that means.
View 2 Replies
View Related
Feb 20, 2011
We have a fairly new Asus laptop and for some reason we can't get the wireless to turn on any more.It has a Function button method to turn it on and off and any time you use this button it shows the WLAN simple with a red line through it. No matter how many times you press it it does the same thing.I've tried uninstalling the drivers and reinstalling, ran a security update for the drivers. When I go into the wireless connection and try and turn it on it shows that it has a signal (not sure what to) but a red X next to the connection in windows 7. I can't actually see any wireless signals so I'm kind of at a loss.
View 5 Replies
View Related
Sep 2, 2011
After Irene, we kept power and cable, but our internet went down, or so we thoughtWhen we plug the Ethernet cable from the modem into the computer, internet works fine (I can post this, after all), but when we plug the cable from the modem into our Dell TrueMobile 2300 router, our network appears as "Local Only." The phone cable thing is plugged from the wall into the modem, and the ethernet cable goes from the modem to the router, as it has been for years.
View 7 Replies
View Related
Nov 8, 2012
I have 2 cisco Aironet 1252 setup as a point to point link using an external antenna (one radio is setup as the root bridge the other is setup as the non-root bridge). Now I see that the connection between the radios is established at a speed of 54 Mbps. However when I perform a speedtest on the link I see that the my actual download speed does not exceed the 2,5 Mbps. what can cause my actual speed to be far lower than the 54 Mbps? And what can I do to improve it?
View 16 Replies
View Related
Jul 6, 2005
When I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
View 3 Replies
View Related
Jan 14, 2012
I have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 Replies
View Related
Sep 18, 2012
I have a E4200 router(firm 1.0.14), which was acting strange, so I reset it.(Windows PC's were hacked with Bluetooth RAT) I did a 30-30-30 reset, and flashed v1.0.14 firmware again.
Presently, I'm using Ubuntu Linux 12.04 LTS, to access Setup(Admin) via computer. After changing to a strong password to access the Admin, I setup everything, as it appeared, [when I used Cisco home network app in Windows, then went in and wrote everything down, in a (paper)notebook], that I keep locked in the safe.
Next, I set the SSID as JCs Gate, expecting JCs Gate & JCs Gate-Guest to appear wireless, after setting up WPA2 security(for both bands), and turning on guest AP and limiting it to 3 as not many use it. After saving and rebooting the router, I am still seeing Cisco23540 as my SSID, and I prefer not to broadcast my router make, as I've reported the neighborhood kid(to his father), after several hacking attempts, from his MAC addy(which I know because I see it in the logs, and sold them the PC custom built) and want to get Cisco out of the SSID.
I'm a hardware IT tech pro, with a MCSE cert, so I'm not a stranger to router setups, after 15+ years in the biz. Either, I'm missing something or going crazy. BTW for about 1hour both JCs Gate and Cisco 23540 were both broadcasting.
View 3 Replies
View Related
Jul 14, 2012
we are using wism 4404 code 4.2 , we are using this old code becuase of 1250 mesh APs, now when a user connect to our network and he is using intel proset software he can see details of our AP, like mac, type and AP ip address 9 which in this case it the controllers ip address) is there a way we can prevent the ap from showing it?...we will be doing an upgrade to 7.0.230 soon. will the upgrade takes care of this problem or there is a way to fix it.
View 5 Replies
View Related
Oct 10, 2012
I have connected my 2504 to a 3560 switch via a UTP SFP on a Gig port.
I have my management on 10.0.0.x I have tried tagging the port and untagging.
When I connect to the 3560 the interface comes up a-1000 a-full but when I look on the WLC the port I am using, port 1, shows Link status down.
The green light is on both the WLC port and the 3560 port but I cannot get the link status to come up on the WLC nor can I ping the WLC.
It must be something dumb I have missed.
The WLC port is autonegotiate too.
View 7 Replies
View Related
Sep 3, 2012
I have a cisco wireless power injector for Aironet 1250 but I called Cisco and was told this can't be found in the system.
View 9 Replies
View Related
Aug 30, 2011
Do I have a virus my when I try to get on the internet at home is wont allow me in, it keeps popping "not working at time" my wireless is good. what can i do?
View 1 Replies
View Related
Jan 1, 2013
My Hp laptop does not shows the wireless adapter in my network and sharing folder how can i fix it? i cannot connect on my wifi because of it .
View 1 Replies
View Related
Nov 6, 2012
I recently build a Frankenstein desktop, or at least that's what I'm calling.I started out replacing the motherboard in a HP Pavillion p6130y desktop.After some research I found that the stock motherboard as pretty outdated so I decided to go aftermarket.I wanted to replace as little as possible but now the only original parts are the dvd drive and network card.The network card has to screws on the back to attach an antenna and is a PCI1x card.
I now have a problem where after installing the card and Windows 7 Professional , I can see the list of available wireless networks including my own.But, I cannot connect to any of them even though my own network has full signal strength.
View 2 Replies
View Related
