Cisco Wireless :: WAP4410N Shows Only One SSID
Feb 22, 2012
I have a 4410N set up on my network. I'm using 4 VLANs on my network, of which, I use my default VLAN 1, as the "public" VLAN which we use to give our clients free WiFi. I would like to have two SSIDs visible from the access point, one unsecured and connected to VLAN 1, and the other secured with WPA2 and connected to our office VLAN on which various servers and resources are available. My preference is for both SSIDs to be visible, as there is not a major security issue and as the only IT person, I do not have time to configure every computer which uses the network with the SSID, but I'll do that if I have to.
I set up the 4410N with it's first SSID using our public WiFi name and did not put any security on it. I went to the VLAN page and set it to use VLAN 1 as both the default VLAN and the VLAN for the first SSID. Then I went back to the Basic Settings page and added a second SSID and chose "Enabled". I went to the Security page and left most things as default (Wireless Isolation between SSIDs is enabled) and changed the security settings for the office SSID to WPA2-Personal. Finally I went to the VLAN page and set it's VLAN to 4.
When I go back to my computer, or from other wireless devices, I only see the public SSID, not the office. I do see on my computer (Win7 x64) an "Other Network" option, but the signal strength on that network is significatnly weaker than that of the public SSID. Also, if I try to connect to it using the office SSID name and the password I set, it doesn't connect.
Am I completely misunderstanding how multiple SSIDs are supposed to work? I am working from a lot of assumptions here.
PS I have no clue if this would affect it, but in the interest of listing all possible factors, the 4410N is powered via PoE and the switch port it is connected to is set to 802.1Q with 1-4 set as the VLANs.
After posting this I discovered that in the Wireless Status page, both SSIDs are listed, but only one (the public SSID) has a MAC listed. I assume I need to add one somewhere. Where should I do this, and what's a "safe" MAC to use that won't conflict with anything?
View 3 Replies
ADVERTISEMENT
May 9, 2012
My WAP4410N is configured with 4 seperate SSIDs. Two of the SSID status are showing "Enabled". The other 2 are shown as "Connected". The one that are showing as Enabled are not receiving any packets. Devices connected to the SSID that shows "Enabled" are unable to connect to the network. Any one else encountered similar issues before? This issue just surfaced few hours ago. The device has been using for around 2-3 years with minimal issues.
View 1 Replies
View Related
Sep 18, 2012
I have a E4200 router(firm 1.0.14), which was acting strange, so I reset it.(Windows PC's were hacked with Bluetooth RAT) I did a 30-30-30 reset, and flashed v1.0.14 firmware again.
Presently, I'm using Ubuntu Linux 12.04 LTS, to access Setup(Admin) via computer. After changing to a strong password to access the Admin, I setup everything, as it appeared, [when I used Cisco home network app in Windows, then went in and wrote everything down, in a (paper)notebook], that I keep locked in the safe.
Next, I set the SSID as JCs Gate, expecting JCs Gate & JCs Gate-Guest to appear wireless, after setting up WPA2 security(for both bands), and turning on guest AP and limiting it to 3 as not many use it. After saving and rebooting the router, I am still seeing Cisco23540 as my SSID, and I prefer not to broadcast my router make, as I've reported the neighborhood kid(to his father), after several hacking attempts, from his MAC addy(which I know because I see it in the logs, and sold them the PC custom built) and want to get Cisco out of the SSID.
I'm a hardware IT tech pro, with a MCSE cert, so I'm not a stranger to router setups, after 15+ years in the biz. Either, I'm missing something or going crazy. BTW for about 1hour both JCs Gate and Cisco 23540 were both broadcasting.
View 3 Replies
View Related
Oct 12, 2011
I can't configure the SSID more than one in the web UI of the WAP4410N. Except I can type the first SSID1, the rest SSID2 - 4 are grey which not allow me to type in anything. ( See attached the screen shot ) My current version is 2.02.1 and I was using IE8 under windows 7.
View 3 Replies
View Related
Sep 8, 2009
Looking to setup 3-4 WAP4410N AP's but only want to use 1 SSID and one set of keys if possible.
View 15 Replies
View Related
Nov 14, 2010
I have a wap4410n acting as AP and a second wap4410n acting as wds repeater.
I've only managed to get the wds repeater to work when it has a different ssid to that of the ap - I'd like the wds repeater to have the same ssid as the ap, should things work in this configuration?
View 21 Replies
View Related
Jun 2, 2010
We just got a WAP4410n and cant seem to get multiple SSID's to show up when searching for them.Only SSID1 shows up in Kismet or any other type of Wifi detector software, is it supposed to be like this?I would imagine that it should display both SSID's
-Mynetwork1
-Mynetwork2
Instead of just Mynetwork1, I have tried everything i can think of to connect to the second one but nothing seems to work.
View 40 Replies
View Related
Nov 15, 2011
I have a WAP4410n which has been configured with a single SSID since implementation several weeks ago with no issues. I am now trying to add a second SSID and not having any success. Originally the second SSID was not being assigned a MAC address and thus not being broadcasted. After upgrading firmware to 2.0.4.2 I now see a MAC address associated with second SSID and it is being seen by clients, but they still cannot connect. I reset the AP to default settings and reconfigured from scratch but still no luck. I have two of these APs, the other one is still at FW rev 2.0.1.0 and has same issue (it does have MAC address associated with second SSID so I didn't bother upgrading firmware yet).
I have tried a few different authetication options, including disabling authentication, to no avail. Question - I do not see an IP address associated with the second SSID - is that the problem and if so, how do I fix that?
View 1 Replies
View Related
Jul 3, 2011
i set up the WAP4410N and it can be connected with our router. But it's not protected by our password, but once i have set the password of WAP4410N by changing the security mode to WEP, now i will prompted to password when I connect the AP, but it shows limited connectivity, I can't even access my local LAN resources at all.
View 2 Replies
View Related
Jan 18, 2011
I am trying to use some WAP4410N in client mode, not much luck.In one case they shouldt connect to different unsecured networks controlled by a Cisco 5508 controller.I can get connection to one of the SSID's but not very stable.One ssid can be seen if i switch from ap-mode to client and run a sitesurvey. If i after that run a site survey again the ssid is not shown.Cant get connected. A third ssid acts "normal" but the 4410 never connects.I have a forth case, WPA2 Personal, cant connect.Been trying fw 2.0.3.3 still no succesAre client mode not usefull at all ?
View 6 Replies
View Related
Sep 26, 2011
I have come across a new problem with our WAP4410N. I have set up multiple SSID's for various groups of people and guests at our company, the first and main SSID has set security properly at WPA2-Personal with a 63 character password. So I went ahead and setup the other 3 SSID's with the same security (just to initially get security going was planning on taking down one of them for guest account), but when I boot up my testing laptop, it shows that SSID's 2-4 have no security what-so-ever.
I have re-checked my settings in the Wireless Security tab and they are all still set with the passwords.
I am using: PID VID: WAP4410N-A V02Software Version: 2.0.4.2.
View 1 Replies
View Related
Dec 1, 2011
why my SSID still displays even though I have the SSID Broadcast "Disabled" for 5 GHz and 2.4Ghz configurations. The name of my network shows full signal strength and a lock next to the name but I was under the impression if I have disabled the SSID broadcast it shouldn't show up at all and would force a user to manually input the network name when trying to connect to it. I have the router configured to only allow certain MAC addresses wireless access as well. Router is running Firmware Version: 1.0.03.Also, my primary computer my iMac running 10.7.2 boots up or is brought out of sleep mode I constantly need to go up to the top of my screen and re-select my network.
View 4 Replies
View Related
Jan 27, 2012
Just got an E2500 and installed it with no problems and it was working correctly for 1-2 days. This evening the signal strength of my SSID dropped to LOW and a new SSID now shows up with full signal strength. It s not an SSID from any of my neighbors and from checking several forums it appears this is known problem.
View 2 Replies
View Related
Jul 10, 2012
My church has a AT&T wired modem and a Netgear Wireless router. Pastors office is on other side of church and he is losing signal occassionally. His network is showing two SSID addressed cgcg cgcg2
View 4 Replies
View Related
Nov 18, 2012
The router is a N Wireless Router. When I try to connect to my router through my phone the SSID appears as belkin.2lc and it won't connect but says authorizing then disconnected. The weird thing is that my laptop and all my roommates laptops and my Xbox can all see the routers real SSID and connect.just fine. I've tried restarting the router and my phone. I've also checked my router settings and made sure their is no MAC address enabled.
View 16 Replies
View Related
Sep 18, 2012
My question is if I can configure 3 ssid, for 3 different VLAN and add the DHCP address from a WAP4410N AP, when you upgrade to the latest version of IOS I can have this functionality?
View 2 Replies
View Related
Apr 30, 2011
I have the following equipment:
Cisco 871W router
2x WAP 4410N APs running 2.0.3.3
I currently have 1 AP connected to the router via copper. The AP to AP link is over 802.11. I have attached a diagram reflecting the current topology.
The AP-to-AP link will come up utilizing B/G/N mixed mode; however, the connection is basically unusable. About 30% of the traffic is dropped, while the packets that do make it have a consistently volatile latency, anywhere from 15 to 1500 ms. I have had success using G-only and B/G mixed. The link is stable (I have had the best results with B/G). The problem is, I didn't buy the 2nd 4410N to run the G protocol. I would like to connect the APs running either B/G/N (hopefully negotiating to N) or N only. I am wondering if there is a certain configuration I can utilize (perhaps using WDS repeater or bridge versus Wireless Client/Repeater?), or a firmware upgrade set for release that can make this happen for me.
View 1 Replies
View Related
Oct 15, 2012
I Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies
View Related
Aug 26, 2012
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
View 4 Replies
View Related
Jan 12, 2012
I have 6 of the 1252 APs that suddenly no longer will associate with any of my 3 4400 controllers. I've verified the power injectors are up and good, shut the port on the switch, and even moved from one power injector to another. Also, in WCS there is a picture of what looks like 3 disks stacked on top of each other, and I don't know what that means.
View 2 Replies
View Related
Feb 20, 2011
We have a fairly new Asus laptop and for some reason we can't get the wireless to turn on any more.It has a Function button method to turn it on and off and any time you use this button it shows the WLAN simple with a red line through it. No matter how many times you press it it does the same thing.I've tried uninstalling the drivers and reinstalling, ran a security update for the drivers. When I go into the wireless connection and try and turn it on it shows that it has a signal (not sure what to) but a red X next to the connection in windows 7. I can't actually see any wireless signals so I'm kind of at a loss.
View 5 Replies
View Related
Sep 2, 2011
After Irene, we kept power and cable, but our internet went down, or so we thoughtWhen we plug the Ethernet cable from the modem into the computer, internet works fine (I can post this, after all), but when we plug the cable from the modem into our Dell TrueMobile 2300 router, our network appears as "Local Only." The phone cable thing is plugged from the wall into the modem, and the ethernet cable goes from the modem to the router, as it has been for years.
View 7 Replies
View Related
Jul 6, 2005
When I view web page of 1410 radio is show ethernet enabled and up but radio as disabled and down. I have tried to enable but to no avail. Is this a sign my radio has gone bad?
View 3 Replies
View Related
Jan 14, 2012
I have cisco LWAPP 1242 AP already joined controller but 802.11b/g shows down on the radio 0 interface. I tried to enable it but it comes with an error" Error in enabling admin status". I have resetted the AP to factory default settings and even replaced with NEW AP.
View 3 Replies
View Related
Jul 14, 2012
we are using wism 4404 code 4.2 , we are using this old code becuase of 1250 mesh APs, now when a user connect to our network and he is using intel proset software he can see details of our AP, like mac, type and AP ip address 9 which in this case it the controllers ip address) is there a way we can prevent the ap from showing it?...we will be doing an upgrade to 7.0.230 soon. will the upgrade takes care of this problem or there is a way to fix it.
View 5 Replies
View Related
Oct 10, 2012
I have connected my 2504 to a 3560 switch via a UTP SFP on a Gig port.
I have my management on 10.0.0.x I have tried tagging the port and untagging.
When I connect to the 3560 the interface comes up a-1000 a-full but when I look on the WLC the port I am using, port 1, shows Link status down.
The green light is on both the WLC port and the 3560 port but I cannot get the link status to come up on the WLC nor can I ping the WLC.
It must be something dumb I have missed.
The WLC port is autonegotiate too.
View 7 Replies
View Related
Sep 21, 2010
Well, I sent mine back and they shafted me with a v1 unit.I don't see how you can know what the problem is and still send me a v1 unit.
I contacted SB support and they said no guarantees on getting a v2 unit.
Now I must PAY to send another unit back.With no guarantees, I don't know.
View 8 Replies
View Related
Aug 30, 2011
Do I have a virus my when I try to get on the internet at home is wont allow me in, it keeps popping "not working at time" my wireless is good. what can i do?
View 1 Replies
View Related
Jan 1, 2013
My Hp laptop does not shows the wireless adapter in my network and sharing folder how can i fix it? i cannot connect on my wifi because of it .
View 1 Replies
View Related
Nov 6, 2012
I recently build a Frankenstein desktop, or at least that's what I'm calling.I started out replacing the motherboard in a HP Pavillion p6130y desktop.After some research I found that the stock motherboard as pretty outdated so I decided to go aftermarket.I wanted to replace as little as possible but now the only original parts are the dvd drive and network card.The network card has to screws on the back to attach an antenna and is a PCI1x card.
I now have a problem where after installing the card and Windows 7 Professional , I can see the list of available wireless networks including my own.But, I cannot connect to any of them even though my own network has full signal strength.
View 2 Replies
View Related
Mar 11, 2013
I have cisco AIR-AP1141N-A-K9 its new one ,when i start to work on the pc through CLI ,im getting like this screen after hanged up ,it's not moving to next step?
View 1 Replies
View Related
Dec 4, 2012
I have a WAP4410N that stopped powering on with PoE. The PoE light comes on but the Power and Ethernet light remain off. The link light comes on the port on the switch. I have tried multiple switch ports and tried a different switch.
View 3 Replies
View Related
Jul 20, 2010
I would like to ask for assistance on how to configure one unit WAP4410N access point to work as repeater to one unit WRT120N wireless router.
As a background, I had one WRT120N already in my house before I bought one WAP4410N as advised by a Linksys guy. I wanted to wirelessly extend the signal of my WRT120N wherever its signal is so low around my house. The WAP4410N should work as repeater to WRT120N.
I already configured WAP4410N to work as repeater by enabling all the choices in its wireless AP mode like the “wireless WDS repeater” and the “wireless client/repeater” but to no avail. I successfully setup a similar scenario before using the old pair of one WRT54G and one WAP54G. I replaced the old pair with the newer one ( WRT120N and one WAP4410N).
Is the tandem of WAP4410N and WRT120N can be configured technically as like as what I wanted? Do I need to upgrade the firmware of both devices? Did I miss something in the configuration?
View 2 Replies
View Related
