Cisco Wireless :: WAP 1140 Series After Booting Shows As Hanged Up
Mar 11, 2013
I have cisco AIR-AP1141N-A-K9 its new one ,when i start to work on the pc through CLI ,im getting like this screen after hanged up ,it's not moving to next step?
View 1 Replies
ADVERTISEMENT
Jun 28, 2012
I have an 1113 acs server which is not booting and hanged. Earlier its was working but i am facing the problem from today. I capture after reload the devices its asking for press F2 and F12 but when i try to do same its not allow to do the same.(Also attached the capture)
When i try to check the same through connect the desktop and reload the devices its showing the Cisco logo screen after that its showing the blank screen.is the ACS gone faulty or I will have to try with reimage the devices.
View 2 Replies
View Related
Jul 24, 2012
What's the main technical differences among the 1140 AP series and the 1260 AP series?I know that the 1260 supports external antennas while the 1140 supports internal antennas, but apart from that, is there any other important difference ?
View 10 Replies
View Related
Jun 13, 2012
I have a number of existing 1140G Access points.I now need to purchase a couple of new AP's to expand coverage and it makes sense to go with the latest N standard ones.Currently I only have standalone models and at the moment I don't have the budget to purchase a management box to allow me to get centrally managed models.
If I purchase 1140N standalone AP's now, can I convert the to centrally managed ones later? If yes, Any disadvantage in doing this?
View 2 Replies
View Related
Mar 27, 2013
I just installed 2 new units and neither will connect to a new HP gigabit switch - no link light, other devices can connect to the switch OK. Their gigabit ethernet settings are set to auto for duplex and speed. I also tried forcing one of them to full duplex and 1000 Mbps which didn't work either. They're both powered by POE injectors. If I connect them to a 10/100 switch they work fine.
View 8 Replies
View Related
Apr 24, 2011
I am facing a strange problem in my WLAN Setup. none of my wireless clients are able to associate with Wireless LAN but when I delete and create a new wireless profile in WLC 4404 clients starts associating with WLAN. every 2-3 days I had to delete and create wlan profile. Is it related to IOS bug or any other problem? My Wireless LAN Controller image is AIR-WLC4400-K9-5-1-151-0.aes.
View 4 Replies
View Related
Jul 20, 2011
I'm trying to test fast roaming using a Cisco 2100 Series controller and 2 1140 APs. The initial authentication succeeds fine and the wireless connection works ok using WPA2+CCKM and LEAP with a Cisco ACS radius server.The problem is that the client does not attempt to preauthenticate with the other AP because the RSN Capabilities IE in the AP beacons and probe responses do not set the RSN Preauthentication capable bit. I can't figure out what it takes to get the APs to indicate to clients that it can do preauthentication. I'm been crawling through all the documentation I can find, to no avail.
View 1 Replies
View Related
Jun 6, 2011
In my Company there is a core Switch 4500 series , to which in the 1st module servers are connected and in the second module 2960 , 3750 series Switches are connected, problem is that the Utilization of Core switch is very high and the core gets hanged. the configuration of the senerio is VTP domain i.e core is Server and the rest are Clients....
View 12 Replies
View Related
Oct 15, 2012
I Have asa 5520 with the code 8.0, the mem shows 94% and the CPU shows 85%
View 5 Replies
View Related
Mar 6, 2012
Can Controller 4400 series work with Aironet 3600 series?
View 5 Replies
View Related
Mar 31, 2013
AP not booting and am not able to boot. Xmodem file system is available.flashfs[0]: unable to allocate available block.
The system has been interrupted, or encountered an errorduring initializion of the flash filesystem. The followingcommands will initialize the flash filesystem, and
[Code]....
View 3 Replies
View Related
Apr 4, 2013
I have a customer that has an air-lap1142. He says that it boot to Rommon, and he has to issue the boot command to get it to boot. What is the rommon command to have the ap boot to the image automatically?
View 1 Replies
View Related
Nov 20, 2012
how to disable radio on the AP 1140 from NCS script .
View 5 Replies
View Related
Jan 28, 2009
I tried to find the radiation pattern for the 1140 AP, but no luck so far. Where to find it?
View 7 Replies
View Related
Apr 18, 2012
I need a legible radiation pattern graph for the 1140 AP -- the antenna pattern. This is for a wireless deployment application which models signal strength. It needs to be specific for the 1140 AP as the antenna has a Maximum gain of 3 dBi which is different than the antenna gain on the 1130 AP.
View 2 Replies
View Related
Apr 25, 2012
my wrt120n cisco wireless router keeps booting me off my network.it is next door usually have a great signal but fades in and out the box for router says its for wireless n.....all i can get is g.can i manually change the settings and should i get a signal booster or a bigger and better wireless router? then i go power cycle my routers and modem and it will sometimes work and sometimes not wifi is next door but less than 50-60'.
View 1 Replies
View Related
Jun 4, 2012
i have 2504 series controller and today its stuck (before was working fine) when i restart it (remove power and power on again) its stuck here (see in snap)
View 4 Replies
View Related
Dec 19, 2010
I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior. I'm having one issue that I can't figure out though. None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless. If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC authentication open authentication key-management wpa guest-mode mbssid guest-mode wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]
View 9 Replies
View Related
Mar 28, 2012
I try to setup a 1141 aironet AP to authenticate my user through our Ms Radius Server ( Win 2008 R2).Everything is fine with small Bussiness AP WAP4410N with the following configuration:But I can't setup successfully the aironet 1141 with the same settings and getting it works.Here is my configuration for the Aironet 1141 Vlan 1 is the ssid I want to get it work with Radius.
View 1 Replies
View Related
Dec 16, 2012
We have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies
View Related
Dec 10, 2012
If I do a speed test (bandwidthplace.com) while connected to a remote locations 1140 standalone access point, the download/upload speeds are roughly 100kbps. There are no other devices connected to the access point at the time. Wired PCs on the LAN that the access point is connected to are not having a problem.Pings from the laptop, through the access point, to our central WAN router are at <10ms.The WAN circuit (remote location to headquarters) is 5Mbps. No congestion.Circuit out from headquarters to I'net is 50Mbps. No congestion.Access point and router interfaces show no errors or collisions, etc. The configuration is the same as 28 other standalone access points in 28 different LANs on the WAN. They have no problems.
View 5 Replies
View Related
Jan 2, 2013
I have 3 Cisco AP 1140 at my customer (Service Industry) place, so they requenst us to provide Hotspot solution to them for managing the Internet connection for limiting to their Customers over the account system. Let me know how i can integrate hotspot BOX with Cisco AP.
View 3 Replies
View Related
Apr 23, 2013
I have one 5508 with Product version 6.0.199.4 and about 7 Cisco 1140 APs.We have a next problems. Go out of the connection on the clients PC, while physically a wireless connection to the workstations is not broken, but access to network resources is lost and restored after some time (up to about one minute).The logs on the controller at the same time see the following message.
View 3 Replies
View Related
Mar 11, 2012
We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the
WLC.AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
[Code] .....
The time is set to the WLC with the NTP. Don't lookup at the time the logs were made - they were made not during the same day/time
View 6 Replies
View Related
Aug 9, 2012
when I try to configure my autonomous 1140, it does not work unless I use numbers.If I put in my phone number as my key, I can authenticate just fine. When I change it to some random letters and numbers.
View 6 Replies
View Related
Aug 8, 2012
I have an Aironet 1140 AP that will not connect to the network when on PoE (either using a Cisco PoE injector) or a Avocent Switch that provides PoE.
The AP will boot up and and devices will connect to it (the LED changes to blue) but none of the devices can get access to the corporate network or internet. When the AP is powered by the standard power supply, it operates normally, i.e. devices can access the network. Are there settings that can be changed to get the AP to work correctly on PoE?
View 4 Replies
View Related
Jun 16, 2012
I am trying to chang IP configuraton for my Cisco 1140 AP, but in CLI I dont have a "config" command (i used en before to enable administrative mode)
Bellow are the commands I can see:
AP7081.0506.d54a#?
Exec commands:
cd Change current directory
[Code].....
View 5 Replies
View Related
Nov 18, 2012
I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies
View Related
Jun 4, 2012
I have recently setup one stand alone aironet 1140 with mostly default settings with WPA key. but, it seems sometimes it's dropping the connections. hardly 15 users are connecting to aironet at the moment.
View 2 Replies
View Related
Oct 31, 2012
Just a few days ago, one of my coworkers computer was unable to see any of our wireless access points - all aironet 1140. He is one of two using a Win 7 machine, everybody else uses Mac with either Lion or Mountain Lion. The Macs can "see" and connect to our wireless AP's just fine.
The odd thing is that is his computer can pick up our neighbors wireless access points, but can't "see" ours. Also, a few peoples phones can no longer detect them either - both iphone 4's (ios 5.1.1 and 6) and androids (2.3 and 4)
No changes were made to our AP's, then people started having wifi issues.
View 10 Replies
View Related
Nov 6, 2012
The command that is given returns an error at the letter a in archive. The command I used was: archive download-sw /overwrite /reload tftp:// obviously with my tftp server info and file name at the end. I logged in with privileged EXEC mode as directed, but archive is not listed when I type ? to get a list of commands. I need to have this AP up and running by Monday.
View 3 Replies
View Related
Nov 28, 2011
We are using the CISCO-DOT11-ASSOCIATION-MIB in a Cisco Air AP 1140 device with release 12/4(21a)JA1 to find out the radio type of wireless client (B/G or N). The clients in question are of type Wireless N and Wireless B/G. We are querying cDot11ClientDevType and cDot11ClientRadioType but the relation between the returned values and client/radio type is not clear:
2 devices returned: cDot11ClientDevType = 102 ==> pc4500Client(102) - client with a 4500 radio and ClientRadioType=2==> ccxClient(2) - CCX- compatible radio1 device returned: cDot11ClientDevType = 1==> unknown (1) – unknown and ClientRadioType= 1==> unknown(1)
Questions: On a Cisco Air AP 1140 device
What OID needs to be polled to find if the client's radio type?What value is returned by this OID if the radio type is B/G?What value is returned by this OID if the radio type is N?
View 1 Replies
View Related
Mar 4, 2013
I have two LAP1041 with WLC2504 everything works fine. But since yesterday when it boots up it flashes green, then solid green, then after about 10 seconds the green LED turns off, however the LAP is still working fine, Why is that? If I put my eyeball up close to the LED I see dim red inside the LED plastic cover.
View 3 Replies
View Related