Cisco Wireless :: Radiation Pattern For 1140?
Jan 28, 2009I tried to find the radiation pattern for the 1140 AP, but no luck so far. Where to find it?
View 7 Replies
ADVERTISEMENT
Cisco Wireless :: Radiation Pattern For 1140
Apr 18, 2012I need a legible radiation pattern graph for the 1140 AP -- the antenna pattern. This is for a wireless deployment application which models signal strength. It needs to be specific for the 1140 AP as the antenna has a Maximum gain of 3 dBi which is different than the antenna gain on the 1130 AP.
View 2 Replies View RelatedCisco Wireless :: 1140 APs Internal Antenna Radiation Pattern
Aug 22, 20111. Cisco Aironet 1040, 1140, 3500i Series Integrated Antennas Diagrams show Azimuth Plane Radiation Patterns and Elevation Plane Radiation Patterns when AP is mounted vertically on the wall (red LED above Cisco logo). So "Zero" on Azimuth Plane points to direction rectangular to AP's case plane (mounting wall plane), "Zero" on Elevation Plane points to ceiling and "180 degrees" points to floor?
2. Radio waves polarization in this case would be linear, in direction from ceiling to floor?
3. If AP would be mounted horizontally on the ceiling, then polarization would be in direction parallel to floor axis X and rectangular to floor axis Y? So induced signal on notebook integrated antenna, oriented rectangular to floor axis X, would be near zero?
Cisco Wireless :: Locate Radiation Pattern For 3502 With Internal Antenna?
Oct 24, 2010I am trying to locate the radiation pattern for a 3502 with an internal antenna. We have some high ceilings so the elevation pattern could impact our placement strategy.
View 6 Replies View RelatedLinksys Wireless Router :: E1200 Access Pattern Not Found
Jan 26, 2012I have a secondary router (E1200) on my home network, connected LAN to LAN. I use it mainly for wired connections, and it does work for that. But when I try to access this router through the IP address, I get a page that says only "ACT_IDLE". Occasionally, I am able to access, but I've found no pattern to when the router is accessible and when it is not...mostly not.
View 1 Replies View RelatedRadiation From Wired Network?
Jun 24, 2011a friend of mine who is an electrical engineer said that the level of radiation from a powerline extender(such as Netgear produce) is much greater than from a wireless network, as it has to 'overcome' the radiation of the house electrical circuit. As my daughter is chronically sick, we are very concerned to arrive at a solution which results in the lowest level of radiation possible.
View 1 Replies View RelatedLinksys Wireless Router :: Diagram Showing Antenna Position / Signal Pattern From EA2700
Apr 26, 2012Any diagram showing the antenna position or signal pattern from the EA2700? I know that Cisco recommends that the unit be placed "near the ceiling" but I'm looking for more specific information. Should the unit be mounted vertically or horizontally.
View 1 Replies View RelatedCould Radiation From 120v Line Have Penetrated Cat 5
Aug 7, 2011I am installing an LED digital sign. The sign is 200 feet away from the controlling computer which has a sending card. The sign has a recieving card inside. Probably not a bright idea at this long distance, but I ran the cat 5 along with the 12/2 power line to the sign. When firing up the sign, the recieving card in the sign is not getting data. I tried it again with another cat5 seperated by ten feet or more from the power line, and still no communication. My question is, could the radiation from the 120v line have penetrated the cat 5 and basically fried the receiving card?
View 3 Replies View RelatedCisco Firewall :: PhishTrap Pattern Update Failed - ASA-SSM-CSC-20
Jan 29, 2013I manage one CSC from one of my customers. All ok with this module except updates for PhishTrap pattern.I reset and restarted the module. CSC have valid licence and no warnings about Maintenance Agreement.
I tried to do this operation manualy but stil receive in Update tab the output that packet 1012 it's available but failed to update to this version.In TmuDump file log i see that this .zip file it's downloaded and CSC try to merge with current file (1011) .I attached the part with this step from log file and sh ver output from CSC.
Cisco :: Translation Pattern For Pass-code For 1 IP Phone In Network
May 23, 2012I am trying to create a passcode for 1 IP Phone in a Network and have the following configuration in place as shown below: The plan is that when this IP Phone wants to dial out they will have to dial out the a 4 digit number 5798 followed by the number they want to dial out.The Router i am using is a CCME.
View 1 Replies View RelatedLinksys Wired Router :: BEFSR81 V2 Ports Become Inactive / Upgrade File Pattern Error?
Jan 2, 2012I have the BEFSR81 V2 and every day at least one of the ports become inactive and the router has to be unplugged and plugged back in to reset the ports. I was going to upgrade the firmware from version 2.44.2 to the one on the site 2.45.10 but when it is downloading I get a message at the end upgrade file pattern error. There is a problem with the router that the ports go out or will the firmware update hopefully correct that issue and how to I get the firmware to update
View 2 Replies View RelatedCisco Wireless :: 1140 - How To Disable Radio On AP
Nov 20, 2012how to disable radio on the AP 1140 from NCS script .
View 5 Replies View RelatedCisco :: Standalone Aironet 1140 - VPN Not Working Over Wireless
Dec 19, 2010I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior. I'm having one issue that I can't figure out though. None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless. If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC authentication open authentication key-management wpa guest-mode mbssid guest-mode wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]
Cisco Wireless :: Radius Authentication With Aironet 1140?
Mar 28, 2012I try to setup a 1141 aironet AP to authenticate my user through our Ms Radius Server ( Win 2008 R2).Everything is fine with small Bussiness AP WAP4410N with the following configuration:But I can't setup successfully the aironet 1141 with the same settings and getting it works.Here is my configuration for the Aironet 1141 Vlan 1 is the ssid I want to get it work with Radius.
View 1 Replies View RelatedCisco Wireless :: Aironet 1140 APs And DHCP Configuration
Dec 16, 2012We have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies View RelatedCisco Wireless :: To Diagnose Low Throughput On Aironet 1140
Dec 10, 2012If I do a speed test (bandwidthplace.com) while connected to a remote locations 1140 standalone access point, the download/upload speeds are roughly 100kbps. There are no other devices connected to the access point at the time. Wired PCs on the LAN that the access point is connected to are not having a problem.Pings from the laptop, through the access point, to our central WAN router are at <10ms.The WAN circuit (remote location to headquarters) is 5Mbps. No congestion.Circuit out from headquarters to I'net is 50Mbps. No congestion.Access point and router interfaces show no errors or collisions, etc. The configuration is the same as 28 other standalone access points in 28 different LANs on the WAN. They have no problems.
View 5 Replies View RelatedCisco Wireless :: AP 1140 Integrating With Hotspot Gateway
Jan 2, 2013I have 3 Cisco AP 1140 at my customer (Service Industry) place, so they requenst us to provide Hotspot solution to them for managing the Internet connection for limiting to their Customers over the account system. Let me know how i can integrate hotspot BOX with Cisco AP.
View 3 Replies View RelatedCisco Wireless :: Client Connection On 5508 / 1140 AP
Apr 23, 2013I have one 5508 with Product version 6.0.199.4 and about 7 Cisco 1140 APs.We have a next problems. Go out of the connection on the clients PC, while physically a wireless connection to the workstations is not broken, but access to network resources is lost and restored after some time (up to about one minute).The logs on the controller at the same time see the following message.
View 3 Replies View RelatedCisco Wireless :: Converted 1140 AP And Cannot Join The WLC 5508
Mar 11, 2012We have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the
WLC.AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
[Code] .....
The time is set to the WLC with the NTP. Don't lookup at the time the logs were made - they were made not during the same day/time
Cisco Wireless :: When Try To Configure Autonomous 1140 / It Does Not Work
Aug 9, 2012when I try to configure my autonomous 1140, it does not work unless I use numbers.If I put in my phone number as my key, I can authenticate just fine. When I change it to some random letters and numbers.
View 6 Replies View RelatedCisco Wireless :: Aironet 1140 Not Connecting To Network When No PoE
Aug 8, 2012I have an Aironet 1140 AP that will not connect to the network when on PoE (either using a Cisco PoE injector) or a Avocent Switch that provides PoE.
The AP will boot up and and devices will connect to it (the LED changes to blue) but none of the devices can get access to the corporate network or internet. When the AP is powered by the standard power supply, it operates normally, i.e. devices can access the network. Are there settings that can be changed to get the AP to work correctly on PoE?
Cisco Wireless :: Missing Configuration Command In CLI (1140 AP)
Jun 16, 2012I am trying to chang IP configuraton for my Cisco 1140 AP, but in CLI I dont have a "config" command (i used en before to enable administrative mode)
Bellow are the commands I can see:
AP7081.0506.d54a#?
Exec commands:
cd Change current directory
[Code].....
Cisco Wireless :: Multiple SSID In Aironet 1140?
Nov 18, 2012I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies View RelatedCisco Wireless :: Aironet 1140 Dropping Connections?
Jun 4, 2012I have recently setup one stand alone aironet 1140 with mostly default settings with WPA key. but, it seems sometimes it's dropping the connections. hardly 15 users are connecting to aironet at the moment.
View 2 Replies View RelatedCisco Wireless :: Aironet 1140 Suddenly Not Detected
Oct 31, 2012Just a few days ago, one of my coworkers computer was unable to see any of our wireless access points - all aironet 1140. He is one of two using a Win 7 machine, everybody else uses Mac with either Lion or Mountain Lion. The Macs can "see" and connect to our wireless AP's just fine.
The odd thing is that is his computer can pick up our neighbors wireless access points, but can't "see" ours. Also, a few peoples phones can no longer detect them either - both iphone 4's (ios 5.1.1 and 6) and androids (2.3 and 4)
No changes were made to our AP's, then people started having wifi issues.
Cisco Wireless :: Making Aironet 1140 Autonomous?
Nov 6, 2012The command that is given returns an error at the letter a in archive. The command I used was: archive download-sw /overwrite /reload tftp:// obviously with my tftp server info and file name at the end. I logged in with privileged EXEC mode as directed, but archive is not listed when I type ? to get a list of commands. I need to have this AP up and running by Monday.
View 3 Replies View RelatedCisco :: 1140 - Radio Type Of Wireless Client B / G Or N
Nov 28, 2011We are using the CISCO-DOT11-ASSOCIATION-MIB in a Cisco Air AP 1140 device with release 12/4(21a)JA1 to find out the radio type of wireless client (B/G or N). The clients in question are of type Wireless N and Wireless B/G. We are querying cDot11ClientDevType and cDot11ClientRadioType but the relation between the returned values and client/radio type is not clear:
2 devices returned: cDot11ClientDevType = 102 ==> pc4500Client(102) - client with a 4500 radio and ClientRadioType=2==> ccxClient(2) - CCX- compatible radio1 device returned: cDot11ClientDevType = 1==> unknown (1) – unknown and ClientRadioType= 1==> unknown(1)
Questions: On a Cisco Air AP 1140 device
What OID needs to be polled to find if the client's radio type?What value is returned by this OID if the radio type is B/G?What value is returned by this OID if the radio type is N?
Cisco Wireless :: 1140 LWAPP / Local Bridge On Controller AP?
Sep 5, 2011I have a Cisco controller WLAN solution where I want to bridge traffic locally on a remote site, when using Cisco 1140 LWAPP.Is the only way H-REAP ?
View 3 Replies View RelatedCisco Wireless :: 1140 Cannot Roam From One AP To Another Without Dropping Internet Connection
Feb 6, 2012I've got two Cisco Aironet 1140 Access Points in my office. They're both setup as AP at opposite ends of the office with the same SSID, so employees can walk throughout the office without losing connectivity. We recently re-started one of the AP's, but ever since the re-start, users cannot roam from one AP to another without dropping their internet connection to the outside world. In other words, if I originally connect on Side A and walk over to Side B, I lose my internet connection. Users can still access the internal network, and I can launch the web interface for both AP's. But, it seems like the DNS doesn't recover until I go back to Side A.
View 6 Replies View RelatedCisco Wireless :: Aironet 1140 Standalone AP To Have Radio Management
Dec 28, 2011For some time now I have been looking for a good business class wireless AP. I've narrowed it down to the Cisco Aironet 1140 standalone (no controller). I'm no stranger to Cisco products. I've worked with their routers, switches and Pix/ASA firewalls. However, I've not had the opportunity to work with their wireless AP's. Anyone using these AP's (more specifically the 1140 standalone), can provide information on the reliability and security of these devices. Some of the features I would like to have like Radio Mgmt. and Rogue AP Detection I see are only available on the controller based units. Does not having these features on the standalone unit reduce its reliability and security? This is for a small business and the budget does not allow to drop for a controller at this time.
View 7 Replies View RelatedCisco Wireless :: WAP 1140 Series After Booting Shows As Hanged Up
Mar 11, 2013I have cisco AIR-AP1141N-A-K9 its new one ,when i start to work on the pc through CLI ,im getting like this screen after hanged up ,it's not moving to next step?
View 1 Replies View RelatedCisco Wireless :: 1140 / 1160 - Enabling Roaming Between Standalone AP?
May 29, 2013I'm about to purchase 2 Aironet APs, either 1140 or 1160 Series for a small Business. I know too little about the AP installation. How to let both APs works in Roaming Mode so that users can move freely within the site without having to drop and connect from one AP to the other.
View 4 Replies View RelatedCisco Wireless :: 1140 - One SSID In AP Don't Give IP Address To Users
May 8, 2013 I have an AP Aironet 1140 that have two (2) SSID: (ZDE) and (GUEST). Guest is working fine but ZDE is not giving IP addresses to users attached in this AP. I atached the sh tech of the Ap. From the configuration cisco guide of Aironet 1140 i understand that by default, access points are configured to receive IP settings from a DHCP server on your network. But i don´t know if i have to configure the dhcp server ip addres in the Ap, similar to the ip helper address in switches
Configuring the Access Point to Provide DHCP Service. These sections describe how to configure the wireless device to act as a DHCP server:
•Setting up the DHCP Server, page 5-22
•Monitoring and Maintaining the DHCP Server Access Point, page 5-24
•Setting up the DHCP Server
By default, access points are configured to receive IP settings from a DHCP server on your network. You can also configure an access point to act as a DHCP server to assign IP settings to devices on both your wired and wireless LANs.
The 1100 series access point becomes a mini-DHCP server by default when it is configured with factory default settings and it cannot receive IP settings from a DHCP server. As a mini-DHCP server, the 1100 series access point provides up to 20 IP addresses between 10.0.0.11 and 10.0.0.30 to a PC connected to its Ethernet port and to wireless client devices configured to use no SSID, and with all security settings disabled. The mini-DHCP server feature is disabled automatically when you assign a static IP address to the 1100 series access point. Because it has a console port to simplify initial setup, the 1200 series access point does not become a DHCP server automatically.