when I try to configure my autonomous 1140, it does not work unless I use numbers.If I put in my phone number as my key, I can authenticate just fine. When I change it to some random letters and numbers.
View 6 RepliesThe command that is given returns an error at the letter a in archive. The command I used was: archive download-sw /overwrite /reload tftp:// obviously with my tftp server info and file name at the end. I logged in with privileged EXEC mode as directed, but archive is not listed when I type ? to get a list of commands. I need to have this AP up and running by Monday.
View 3 Replies View RelatedI am in the process of installing an Aironet 1140 standalone AP. I have not worked with these AP's before. I will be connecting it to one of the PoE ports on the existing ASA 5505. My goal is to have 2 SSID's, one for internal network and one for guest internet only, no access to internal LAN. I want to have the internal wifi clients and the guest clients on seperate IP networks. The internal clients obtain DHCP from the existing server and use the ASA DHCP server for the guest clients. And of course, I would like the ability to manage the AP from the internal network. I am providing copies of my current configs for both the ASA and Aironet.
View 4 Replies View RelatedMay the air-cap3602 work in autonomous system? or only with a WLC?
View 5 Replies View RelatedI have a 3602e access point which I need to configure. It has been loaded with an autonomous image (for survey work) and my only access currently is via a browser. Is it possible to http into this access point if its only been imaged and not configured.
View 5 Replies View RelatedWe purchased some 3502e's and I was told we could set them up as automous ap's to do a site survey. however i haven't come across much online for instructions. i saw one post that mentioned downloading code for another ap model - i think a 1260, but we don't have rights for such a download.
View 11 Replies View RelatedI have 14 unit of Air-AP1142n. No controller. All unit were in a warehouse, each of the AP distance each other around 40mI would like to use only 4 SSID instead of 14 SSID.
View 5 Replies View RelatedWhat 113X AP model will work in Autonomous and LightWeight Mode? I want to buy some 113X AP's for my lab and want to make sure I don't get stuck with the ones that only run in one mode. I am looking at buying this one AIR-AP1131AG-N-K9 802.11a/b/g. Will this model work in both modes?
View 1 Replies View RelatedI have configured my AP with MBSSID and it does work fine. now I need to take it to the next level and introduce the 2nd ssid to be my home guest network for friends and family that are visiting. What else should I include on this configuration to allow for a hot spot where the user logons and must authenticate themselves via a secure web browser before going out to the internet. Next question would be how to increase the security of the device and the AP.
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec
[Code].....
I have a Cisco Aironet 1140 with ENABLED broadcasting SSID, encryption is WPA2(personal). Ubuntu 12.04 and Windows 7 are authenticated, but MACBooks never be authenticated. Any specific configuration for MAC books?
View 6 Replies View RelatedAny configuration example where i have a Cisco 1140 connected with a trunk to one router and with the Cisco 1140 i broadcast one SSID per vlan, one with WPA2 and other "open".?I ask because i see that when i turn on cipher, i cant configure an SSID without encryption.
View 1 Replies View RelatedI have here a canyon wireless router. do you know where I can find online a tutorial or manual on how to configure a wireless router so that it acts as a repeater?
View 3 Replies View RelatedI purchases a Hauppage USB TV tuner and bought the software that allows live TV signals to be streamed to my home PC or android phone. Once I installed the software and ran a test, the remote access failed. The error message said I need to check the router's configuration. I know very little about configuring routers, but the model is WRT54Gv3.
View 1 Replies View RelatedIs there a way to configure one of the GigE ports on the E4200 to only work on the "guest" network? Basically I have a need to setup one of those ports to get to the Internet, but I don't want it to be able to get to anything else on the private side.
View 1 Replies View Relatedis it possible to configure a Cisco 878 Router to act as a device(router) between a DSL Modem and the LAN ?
There is the following scenarium: "Deutsche Telekom DSL Modem -> Cisco Router 878 -> LAN"
DSL is an SDSL Connection with a static IP address.
Right now I have it connected like this: Internet-> SURFboard SB6120 Modem -> DGL-4100 Router (modem in the WAN port, 3 internet connections plus the switch in the LAN ports) -> DGS-1008G Switch (2 other internet connections connected to this, as well as an Xbox 360).The problem is that everything connecting to the router works, and nothing works on the switch even though the power light is on (however, the port on the router that is receiving the switch is not lit up). I'm guessing this is because the router only assigns as many IP addresses as it has ports or something.
View 10 Replies View Relatedis it possible to use cisco AnyConnect client to connect users with Cisco VPN 3000 appliance?If so how to configure VPN 3000 concentrator to work with AnyConnect?
View 1 Replies View Relatedhow to disable radio on the AP 1140 from NCS script .
View 5 Replies View RelatedI tried to find the radiation pattern for the 1140 AP, but no luck so far. Where to find it?
View 7 Replies View RelatedI need a legible radiation pattern graph for the 1140 AP -- the antenna pattern. This is for a wireless deployment application which models signal strength. It needs to be specific for the 1140 AP as the antenna has a Maximum gain of 3 dBi which is different than the antenna gain on the 1130 AP.
View 2 Replies View Relatedhow to configure dhcp relay agent and how it's work
View 1 Replies View RelatedHow to configure a 4500X with a GLC-T SFP so that it will work at 100M.The data sheets say it will work at 10/100/1000 but Im not seeing that happen can't set the speed and it doesn't negotiate with anything at 100M it will only work with auto to another switch set to auto and supports 1000M.
View 6 Replies View Relatedmake a couple of SF300 switches to work properly with a C2960S-48TS-L that acts as core switch/basic router. I can't seem to figure out how to assign VLANs correctly in trunk and access mode on the SF300. The 2960S are a no brainer with IOS commands but the webgui in the SF300 is a pain.
I've configured the 2960S with 3 VLANs and I would like to have the SF300 switches connect to the C2960S-48TS-L through VLAN trunk and then configure the ports on the SF300 switches to belong to the assigned VLANs of my choosing. I would also like to have all the SF300 switches management interface in VLAN 50.
I've partially described the enviroment below.
VLANs
Data VLAN 10: 192.168.10.0
Management VLAN 50: 10.20.30.0
Voice VLAN 100: 10.10.10.0
[Code].....
I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior. I'm having one issue that I can't figure out though. None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless. If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC authentication open authentication key-management wpa guest-mode mbssid guest-mode wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]
I try to setup a 1141 aironet AP to authenticate my user through our Ms Radius Server ( Win 2008 R2).Everything is fine with small Bussiness AP WAP4410N with the following configuration:But I can't setup successfully the aironet 1141 with the same settings and getting it works.Here is my configuration for the Aironet 1141 Vlan 1 is the ssid I want to get it work with Radius.
View 1 Replies View RelatedWe have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies View RelatedIf I do a speed test (bandwidthplace.com) while connected to a remote locations 1140 standalone access point, the download/upload speeds are roughly 100kbps. There are no other devices connected to the access point at the time. Wired PCs on the LAN that the access point is connected to are not having a problem.Pings from the laptop, through the access point, to our central WAN router are at <10ms.The WAN circuit (remote location to headquarters) is 5Mbps. No congestion.Circuit out from headquarters to I'net is 50Mbps. No congestion.Access point and router interfaces show no errors or collisions, etc. The configuration is the same as 28 other standalone access points in 28 different LANs on the WAN. They have no problems.
View 5 Replies View RelatedI have 3 Cisco AP 1140 at my customer (Service Industry) place, so they requenst us to provide Hotspot solution to them for managing the Internet connection for limiting to their Customers over the account system. Let me know how i can integrate hotspot BOX with Cisco AP.
View 3 Replies View RelatedI have one 5508 with Product version 6.0.199.4 and about 7 Cisco 1140 APs.We have a next problems. Go out of the connection on the clients PC, while physically a wireless connection to the workstations is not broken, but access to network resources is lost and restored after some time (up to about one minute).The logs on the controller at the same time see the following message.
View 3 Replies View RelatedWe have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the
WLC.AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
[Code] .....
The time is set to the WLC with the NTP. Don't lookup at the time the logs were made - they were made not during the same day/time
I have an Aironet 1140 AP that will not connect to the network when on PoE (either using a Cisco PoE injector) or a Avocent Switch that provides PoE.
The AP will boot up and and devices will connect to it (the LED changes to blue) but none of the devices can get access to the corporate network or internet. When the AP is powered by the standard power supply, it operates normally, i.e. devices can access the network. Are there settings that can be changed to get the AP to work correctly on PoE?
I am trying to chang IP configuraton for my Cisco 1140 AP, but in CLI I dont have a "config" command (i used en before to enable administrative mode)
Bellow are the commands I can see:
AP7081.0506.d54a#?
Exec commands:
cd Change current directory
[Code].....
I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies View Related