Cisco Wireless :: Air-cap3602 Work In Autonomous System

Mar 13, 2012

May the air-cap3602  work in autonomous system? or only with a WLC?

View 5 Replies


ADVERTISEMENT

Cisco Wireless :: AP 1252 - Authentication And Roaming With Autonomous System

Aug 2, 2012

I have three Autonomous AP´s in a small office running voice applications, all of them are connected to the same infrastructure switch and they have same configuration, voice Vlan is configure to open authentication. I have two models of AP 1252 and 1262 and I paste Radio configuration below.

First issue: During calls users are facing problems when roaming between AP´s, and eventually calls are dropped.
Second issue: Sometimes one of these AP´s(1252) lose all transmit signal and when return I got authentication error on log.

View 4 Replies View Related

Cisco Wireless :: How To Configure Hotspot On 1131ag Autonomous System

Jan 13, 2013

I have configured my AP with MBSSID and it does work fine. now I need to take it to the next level and introduce the 2nd ssid to be my home guest network for friends and family that are visiting.  What else should I include on this configuration to allow for a hot spot where the user logons and must authenticate themselves via a secure web browser before going out to the internet. Next question would be how to increase the security of the device and the AP.
 
no service pad
service timestamps debug datetime msec
service timestamps log datetime msec

[Code].....

View 5 Replies View Related

Cisco WAN :: IOS 12.4 (16) / EIGRP Autonomous System Mismatch Detection?

Oct 3, 2007

It is possible to detect situation when two neigbour routers involved in EIGRP routing are configured by mistake with different AS number ?I tried this situation practically. Two routers are connected together via Serial link network. One router has AS 1, other AS 10. I try to detect AS mismatch. First I check what EIGRP packet are comming debug ip packet detail show source <my neighbour IP address> destination 224.0.0.10  Ip protocol type 88. These packets are EIGRP Hello packet.

I try to go more deeply into details.debug eigrp packetsI see only ongoing EIGRP Hello packets. But I don't see any incoming packet from my neighbour (which has different AS number). It seems, because of different AS number router silently drop eigrp packet.Other debug eigrp command also doesn't show any info about AS difference.

Cisco IOS 12.4 (16)

View 9 Replies View Related

Cisco Wireless :: When Try To Configure Autonomous 1140 / It Does Not Work

Aug 9, 2012

when I try to configure my autonomous 1140, it does not work unless I use numbers.If I put in my phone number as my key, I can authenticate just fine.  When I change it to some random letters and numbers.

View 6 Replies View Related

Cisco Switching/Routing :: 6509 BGP X Autonomous System Specification

Mar 25, 2012

I am trying to configure BGP on 6509 IOS. I can not specify a long interger for autonomous system: ASN: 262829 (32 bits)

View 1 Replies View Related

Cisco Wireless :: What 113X AP Model Will Work In Autonomous And Lightweight Mode

Feb 4, 2013

What 113X AP model will work in Autonomous and LightWeight Mode? I want to buy some 113X AP's for my lab and want to make sure I don't get stuck with the ones that only run in one mode. I am looking at buying this one AIR-AP1131AG-N-K9 802.11a/b/g. Will this model work in both modes? 

View 1 Replies View Related

Linksys Wired Router :: How To Set Up RVS4000 QOS Settings To Work With VOIP Phone System

Dec 15, 2011

How to set up RVS4000 QOS settings to work with a VOIP phone system?  I need to get the QOS active on the VPN so that a remote office with VOIP phones can reach the PBX at the main office over the Internet connection. 

View 1 Replies View Related

Cisco Wireless :: 1262N Autonomous AP Configuration?

Oct 26, 2011

We have a couple of autonomous 1262's that I'd like to get configured.  I would like to put the Ethernet interface out on our Internet subnet and have the clients get a RFC 1918 address from the radio's.  Our little Linksys is setup this way and the clients are PAT'ing off the Ethernet interface when they go to the Internet.
 
Is this possible with these guys or do I have to put the AP ethernet interface into the same subnet with the DHCP scope?  I don't have enough Internet IP's to hand out to every wireless client.

View 15 Replies View Related

Cisco Wireless :: Loading An Autonomous OS On A 1250

Nov 14, 2012

When have downloaded the c1250-k9w7-tar.152-2.JA.tar and attempted to load into a 1250 via tftp the process aborts with the following message. [code]

View 2 Replies View Related

Cisco Wireless :: AP 1200 - MAC Filter And WPA Autonomous AP

Jul 19, 2011

I have two wireless networks configured in the AP1200, both SSIDs are configured with WPA.

SSID 01: configured whit WPA
SSID 02: configured whit WPA
 
I have configured the access-list number 700, and I would like to apply to a single network. Achieving the following:

SSID 01 : WPA + Mac Filter, using the ACL number 700.
SSID 02:  WPA
 
How I can apply the list 700 to the first SSID only ??

View 5 Replies View Related

Cisco Wireless :: 1242 - Mode To Autonomous

Aug 13, 2006

i need to change the IOS in a Ligthwiegth Access point and make it work as an Autonomus AP 1242. I have got the image but im not realy clear about the process. I got to enter the Ligthwiegth Access point true the console port but i dont know how is the upgrading process.

View 6 Replies View Related

Cisco Wireless :: Getting Air-lap1042N-E-K9 Lightweight To Autonomous?

Mar 4, 2012

I have a air-lap1042-n-e-k9, how to put this wi-fi mode autonomous ?

View 5 Replies View Related

Cisco Wireless :: 1310 Autonomous To LAP Conversion

Oct 22, 2012

Customer of mine has 20 AP AIR-BR1310G-E-K9. No controller installed. He use them as Autonomous AP.
 
Right now ##he wants indroduce a WLC. Due to that every single AP must be converted in LAP AP.
  
is this action free of charge ? Nedd I SMARTENT COVERAGE ?

View 3 Replies View Related

Cisco Wireless :: Can 3502i Be Downgraded To Autonomous

Oct 1, 2012

Can a 3502i be downgraded to autonomous mode?

View 7 Replies View Related

Cisco Wireless :: Converting 3600 To Autonomous?

Jan 13, 2013

I am not having much luck getting it converted via normal ways. 
 
It times outs on TFTP server when you hold the mode button (a 3500 is working fine doing the same thing). 
 
I try the old school way of archive download-sw but it isn't fast enough before it re-dhcp's because it can't find a controller. "*Mar  1 01:17:51.123: %CAPWAP-3-DHCP_RENEW: Could not discover WLC using DHCP IP. Renewing DHCP IP..'  Even if I set a static IP address.
 
Is there way to disable the join process while I upgrade the software?  I guess fire up a controller for it to join.  I hope I don't have to have a controller to convert these. 

View 31 Replies View Related

Cisco Wireless :: Converting AIRLAP1142 To Autonomous

May 17, 2012

I have an AIR-LAP1142 that I'm trying to load the autonomous software onto.  I reset the AP with the mode button held down as per instructions.  When I release, it attempts to download c1140-k9w7-tar.default from my pc running tftpd62.  Several connections are made and then it eventually times out.  I tried another machine (also win7 x64) and it fails there too exactly the same.
 
TFTP logs show:
 
Connection received from 10.0.0.1 on port 1024 [18/05 17:22:04.269]
Read request for file <c1140-k9w7-tar.default>. Mode octet [18/05 17:22:04.270]
Using local port 51686 [18/05 17:22:04.270]

[Code].....

View 3 Replies View Related

Cisco Wireless :: 3502i Autonomous To Lightweight?

Apr 28, 2013

how to convert a 3502 access point from Autonomous to Lightweight ? 3502 has a new IOS released back in Dec 2012 to work as staandalone mode. I need to convert this back to Lightweight mode.
 
I have been searching on web but have had no luck so far with anything. Tried converting it to lightweight in the same way as putting it on Autonomous IOS but errored out.

View 4 Replies View Related

Cisco Wireless :: How To Access 2602i Autonomous Ap Web GUI

May 22, 2013

I'm trying to configure a 2602i and I know there is a way to access the web GUI to accomplish this but I'm unsure if I have to access CLI to assign the AP and IP or if it already has a default IP?If it has an default IP

View 6 Replies View Related

Cisco Wireless :: WDS On Aironet 1042 Autonomous AP?

Jul 11, 2012

i'm trying to enable WDS with authentication on a Cisco 1042 AP. The unit itself will be the WDS master and Radius server as well it will serve clients (not that many). The AP is running version 12.4(25d).After multiple tries of configurating, I keep getting the same issue: as soon as I connect to the SSID, I can enter the username and password but authentication fails - hence the message in my console: 

%DOT11-7-AUTH_FAILED: Station xxxx.xxxx.xxxx Authentication failed. Every configuration I made was started from factory defaults of the AP.My current tests are with one AP only and if tests go successfully, I will add more infrastructure AP's to the setup.

hostname WDS_SERVER!logging rate-limit console 9enable secret 5 $1$FcRQ$T5MglV/0ybzKEfk3DoN/J0!aaa new-model!!aaa group server radius InfraAP server 192.168.28.34 auth-port 1812 acct-port 1813!aaa group server radius Clients server 192.168.28.34 auth-port 1812 acct-port 1813!aaa authentication login APlist group InfraAPaaa authentication login WirelessClients group Clients!aaa session-id common!dot11 ssid Test   authentication open eap WirelessClients   authentication key-management wpa version 2 cckm   guest-mode!username Cisco password 7 14341B180F0B!bridge irb!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid Test ! antenna gain 0 station-role root bridge-group 1 bridge-group 1

[code]....
 
I've tried the configuration from the Cisco config guide as well but without any luck [URL]

View 5 Replies View Related

Cisco Wireless :: Possible To Configure 3602e AP With Autonomous Load Via GUI?

Mar 7, 2013

I have a 3602e access point which I need to configure.  It has been loaded with an autonomous image (for survey work) and my only access currently is via a browser.  Is it possible to http into this access point if its only been imaged and not configured.

View 5 Replies View Related

Cisco Wireless :: Convert Capwap 1142 To Autonomous

Mar 28, 2012

I have an 1142 running capwap c1140-k9w8-tar.124-23c.JA4  that I am wanting to convert to an Autonomous AP.However, the AP does not seem to have an archive exec  command to tftp downoad an new IOS.Is there another procedure that should be used ?

View 7 Replies View Related

Cisco Wireless :: Convert A 1602i From Lightweight To Autonomous?

Feb 28, 2013

how to convert a 1602i AP from lightweight mode to autonomous?

View 3 Replies View Related

Cisco Wireless :: Convert Aironet 1310 Autonomous To LAP?

Apr 22, 2012

Is it possible to also upgrade the 1310 series cisco ap's from  autonomous to lwap without using the upgrade tool, if so what procedure  do I follow? The upgrade tool required to have telnet enable on the controller which I can't break the policy

View 1 Replies View Related

Cisco Wireless :: Converting 2602 From Lightweight To Autonomous?

Feb 19, 2013

I have a problem converting 2602 from lightweight to autonomous.  It will not boot to the autonomous IOS.  The procedure below is waht I did.
 
ap: set IP_ADDR 10.0.0.1
ap: set NETMASK 255.255.255.0
ap: tftp_init

[Code].....

View 28 Replies View Related

Cisco Wireless :: Does Aironet Autonomous 2600 Support WDS

Mar 20, 2013

Does Aironet Autonomous/Standalone 2602 support WDS (Wireless Domain Service)?
 
I noticed that Aironet Controller-based 2602 does not support WDS.  I would like to use 1242AG series but it will be going EOS soon.

View 3 Replies View Related

Cisco Wireless :: Converting 1040N Autonomous AP To LWAPP

Oct 5, 2011

I have a couple of 1040N autonomous APs want to convert to light weight APs.

View 8 Replies View Related

Cisco Wireless :: Loading Autonomous Image On 1552E

Jan 28, 2013

I've looked through the documentation for loading the autonomous image on a 1552E WAP that has the lightweight image on it.  All the documentation I can find mentions using the "archive" command at the command line.  It doesn't appear to like the archive command.
 
I've seen in the documentation that it also mentions the software is loadable through the controller, but I can't figure out how to do that.
 
I currently have the 1552E connected to my 5508 controllers running 7.3 software. how to load this autonomous image on to the 1552E? I'm planning on using it to do site surveys with the 1552E.

View 7 Replies View Related

Cisco Wireless :: Configure 3502e In Autonomous Mode?

Mar 28, 2012

We purchased some 3502e's and I was told we could set them up as automous ap's to do a site survey.  however i haven't come across much online for instructions.  i saw one post that mentioned downloading code for another ap model - i think a 1260, but we don't have rights for such a download.

View 11 Replies View Related

Cisco Wireless :: Change IOS Of 1252 LWAP AP To Autonomous AP?

Jun 20, 2011

Is it possible to Change IOS of 1252 LWAP AP to Autonomous AP? I have seen some documents for changing Autonomous AP to LWAP and change back procedures.

View 4 Replies View Related

Cisco Wireless :: Do 1042 Autonomous APs Support GRE Tunnels

Jan 24, 2013

Do the 1042 Autonomous APs support GRE tunnels?

View 4 Replies View Related

Cisco Wireless :: Configuring A 1260 Autonomous AP Documentation?

Mar 5, 2012

good docs for configuring a 1260 autonomous AP?

View 1 Replies View Related

Cisco Wireless :: Lan Connectivity On Autonomous AP With Throttles 1242 Ap

Jun 5, 2013

I encounter a strange problem on several AP 1242 in version 12.4(25d)JA1 of a customer : He has 10 autonomous AP covering The APs loose LAN connectivity randomly and therefore the clients don't work anymore. The AP are connected on a 2960 and a 3560 wich are in turn connected on a 3750 wich route the trafic.After checking spanning-tree no loops are present. When I check the counters on the AP involved I see the "trhottles" and "ignored" counters incrementing on the fa0 link of the AP impacted wich mean I think it can't handle the incoming traffic. This incoming traffic seems not to be too big however. I can see drops on the switch interface connecting the AP.

View 2 Replies View Related







Copyrights 2005-15 www.BigResource.com, All rights reserved