Cisco Wireless :: 1140 - One SSID In AP Don't Give IP Address To Users
May 8, 2013
I have an AP Aironet 1140 that have two (2) SSID: (ZDE) and (GUEST). Guest is working fine but ZDE is not giving IP addresses to users attached in this AP. I atached the sh tech of the Ap. From the configuration cisco guide of Aironet 1140 i understand that by default, access points are configured to receive IP settings from a DHCP server on your network. But i don´t know if i have to configure the dhcp server ip addres in the Ap, similar to the ip helper address in switches
Configuring the Access Point to Provide DHCP Service. These sections describe how to configure the wireless device to act as a DHCP server:
•Setting up the DHCP Server, page 5-22
•Monitoring and Maintaining the DHCP Server Access Point, page 5-24
•Setting up the DHCP Server
By default, access points are configured to receive IP settings from a DHCP server on your network. You can also configure an access point to act as a DHCP server to assign IP settings to devices on both your wired and wireless LANs.
The 1100 series access point becomes a mini-DHCP server by default when it is configured with factory default settings and it cannot receive IP settings from a DHCP server. As a mini-DHCP server, the 1100 series access point provides up to 20 IP addresses between 10.0.0.11 and 10.0.0.30 to a PC connected to its Ethernet port and to wireless client devices configured to use no SSID, and with all security settings disabled. The mini-DHCP server feature is disabled automatically when you assign a static IP address to the 1100 series access point. Because it has a console port to simplify initial setup, the 1200 series access point does not become a DHCP server automatically.
View 1 Replies
ADVERTISEMENT
Nov 18, 2012
I am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies
View Related
Apr 26, 2013
I wanted to know if anyone can say with certainty how many clients can stay connected 'Aironet 1140 series. I state that I should connect WiFi in about 350 clients.
View 6 Replies
View Related
Sep 3, 2012
i have a 1140 AP and i have an ssid on it authenticate users from NPS server.
but now i need to conifure on it 2 ssid with different vlans each ssid authenticate from the same NPS server but with diferent groups.
View 1 Replies
View Related
Aug 16, 2011
Any configuration example where i have a Cisco 1140 connected with a trunk to one router and with the Cisco 1140 i broadcast one SSID per vlan, one with WPA2 and other "open".?I ask because i see that when i turn on cipher, i cant configure an SSID without encryption.
View 1 Replies
View Related
Aug 26, 2012
i have configured acs 5.3. i integrated wth active directory also it got suceeded in test connection.but when am trying to conncet ssid its not getting authenticate, wat r the users i created on acs they can able to login on wifi ssid
View 6 Replies
View Related
Dec 14, 2012
I have a WRV4400n in my company and almost every day I have to reboot so people can get out to the internet, It lets you see the local network also if I put a desktop on line it will not give a DHCP address, untill I reboot the router. then all is fine, It has the latest greates firmware.
View 1 Replies
View Related
Sep 25, 2011
I've got threeLinux Boxes (running Centos 6). They were all connected to my cheap WRT54GL-- DHCP worked every time.Absolutely no problems. Both the LInux boxes and the WRT54GL had MTU set to manual, 1492.I replaced the WRTt54GL with the expensive E4200. I set the new router's MTU to manual, 1492. NONE of my Linux boxes ever receive a DHCP address. I look at the logs, and they do DHCPDISCOVER, get DHCPNACK, try several different intervals, and then fail the interface and quit.ALL I did was unhook cables from the WRT54GL and plug into the E4200. Yes, the WRT54GL was powered off. NOTHING was changed in the Linux configs. Yes, DHCP is enabled, address-range assigned, etc. BTW-- one box is dual boot with Win7-- in Win7 (using the same card, obviously), DHCP works just fine. But, Linux doesn't work.
I can give the boxes static IP's, and all is well. Just can't get DHCP to work. I evfen tried putting in DHCP reservations (via MAC assignments) for the E4200-- still doesn't work. The new E4200 is on the 02 firmware (which I believe is cuurent). If I can't iron this simple task out, in a couple of days I'm taking the E4200 back, and getting a refund. I'll stay with my old WRT54GL... it works. Hate to give up on some of the new E4200 features, though.
View 2 Replies
View Related
Feb 28, 2011
if i give gateway of one as ip address of another and vice versa? both are directly connected and u cant use hub, switch,router...
View 7 Replies
View Related
Jun 23, 2011
ho can i give a ip address to webcam
View 1 Replies
View Related
Nov 16, 2011
ok the connection is a dial up it doesn't give any static ip address when i connect it now it will give me different ip , when i disconnect it again it will give me another ip. an the message appear at the server and the affect the client.....the client are using satic ip address.
View 1 Replies
View Related
Aug 9, 2011
RVS4000 router doesnt give out an IP address to a client connecting with QVPN v1.303, connection seems good, router logs the connection and tracks its duration etc but client side does not get an IP from the RVS4000 side -keeps local LAN ip + there is no access to the remote shares etc. RVS 4000 has DHCP enabled. Client side subnet is different to the VPN side. VPN users are setup correctly (Router logs the user as connected) . Port 443 is not setup in port forwarding.
View 3 Replies
View Related
Aug 16, 2011
RVS4000 router doesnt give out an IP address to a client connecting with QVPN v1.303 (or v1.4..- tried that too), connection seems good, router logs the connection and tracks its duration etc but client side does not get an IP from the RVS4000 side -keeps local LAN ip + there is no access to the remote shares etc. RVS 4000 has DHCP enabled. Client side subnet is different to the VPN side. VPN users are setup correctly (Router logs the user as connected) . Port 443 is not setup in port forwarding. (posted in LAN Routing & Switching 2 days ago but I got no response so I thought Id try here !)
View 3 Replies
View Related
Apr 14, 2011
My ISP gave me a Thomson THG520 modem when I subscribed to their service. It has 2 links and USB and an Ethernet link. It worked fine with our 2 computers but for several weeks or so I experiencing that it only gives me IP address only on one interface that one that's first plugged into the computer.
If I reset the modem and plug in the USB I get an IP address immediately. If I unplug the USB and plug in the Ethernet cable I don't get an IP address. If I reset again the modem and plug in the Ethernet cable I get an IP address but not on the USB link after I unplug the modem.
EDIT: after entering the modem's administration I realized it's firmware was updated (probably my ISP did it.). Also I read about how this stuff works, there is an evidence that my ISP set the CPE limit to 1. (so it seem only one computer connected to the modem can get IP address while the other can't.). And this configuration is stored on the modem somewhere. Is there a way to view it somehow?
View 1 Replies
View Related
Mar 2, 2011
I recently configured and installed a 1941ISR for a customer. The customer purchased a 25-User SSLVPN license with the router, and I configured it for remote SSLVPN access. This is working nicely except for one issue: when users initiate an SSLVPN connection request by browsing to the assigned webvpn gateway IP, they get the "There is a problem with this website's security certificate" browser message. They are in the process of working with their DNS hosting provider to get a DNS entry assigned to the IP address so the users won't have to specify an IP address in the URL address box, but they will continue to get the certificate error until/unless I can figure out how to resolve the issue.
I've tried the following "How to make IE8 trust a self-signed certificate in 20 irritating steps" that I found via another forum link but with no luck:
1.Browse to the site whose certificate you want to trust.
2.When told "There is a problem with this website's security certificate.", choose "Continue to this website (not recommended)."
3.Select Tools->Internet Options.
4.Select Security->Trusted sites->Sites.
5.Confirm the URL matches, and click "Add" then "Close".
6.Close the "Internet Options" dialog box with either "OK" or "Cancel".
7.Refresh the current page.
8.When told "There is a problem with this website's security certificate.", choose "Continue to this website (not recommended)."
9.Click on "Certificate Error" at the right of the address bar and select "View certificates".
10.Click on "Install Certificate...", then in the wizard, click "Next".
11.On the next page select "Place all certificates in the following store".
12.Click "Browse", select "Trusted Root Certification Authorities", and click "OK".
13.Back in the wizard, click "Next", the "Finish".
14.If you get a "Security Warning" message box, click "Yes".
15.Dismiss the message box with "OK".
16.Select Tools->Internet Options.
17.Select Security->Trusted sites->Sites.
18.Select the URL you just added, click "Remove", then "Close".
19.Now shut down all running instances of IE, and start up IE again.
20.The site's certificate should now be trusted.
I followed all 20 irritating steps to the letter, but am still getting the security certificate nat.Now when I “Continue to this website (not recommended)” and click on "Certificate Error" at the right of the address bar, the certificate error windows says “Mismatched Address”.Is there a way that I can get this fixed without resorting to a 3rd party CA?
View 5 Replies
View Related
Sep 29, 2012
I have a wireless 5508 with license base to 50 aps, i use a deployment flex connect. I already registered all my access points, I use web authentication to authenticate users guest, and the service dhcp is in the central site.
My issue is the users in each remote site, can not get an ip address by dhcp from the central site, they can authenticate in the guest ssid, but any users can not get an ip. The request is passing by the wan in this way
Central Site DHCP - Router WAN - Remote Site - Users with notebooks. I use flex connect central deployment (all the traffic consulting to the wlc) .
perhaps i should use local deploy? The wireless is in the central site.
View 17 Replies
View Related
Apr 9, 2013
I've been asked to configure mac-address filtering on our WLC 4402 and it was basically straight forward. however i noticed that in creating the filter you can only choose 1 SSID or the other option would be to choose all? My question then is what happens if i need a user one 2 specific SSIDs? can i create separate filters for each SSID but using the same mac?
View 1 Replies
View Related
Sep 13, 2012
We are using Any connect vpn client (v2.5.3055) to an ASA 5520 (v8.4) in a development environment. We use our corporate Radius server to authenticate users. We have certain users which need have the same IP address every time they lo gin. As it is configured now, the IP addresses are assigned sequentially from the pool. Is there a way to allow certain users to get the same IP address each time they log on?
View 3 Replies
View Related
Apr 5, 2011
can i have 2 pools each with diifferent subnet [code] i wanna put restricution on remote vpn users having address from pool-2,and just give them access to 172.16.10.0/24,is it possible on the asa 5510?
View 7 Replies
View Related
Mar 21, 2013
We recently implement WLC 5500 Series, I found out guest user once period of that user expired it will not appear at lobbyadmin page where you can see list of users.
Is there any way to see expired guest users and also IP address which assign to guest user?
View 2 Replies
View Related
Feb 15, 2011
When disabling SSID broadcast and enabling MAC address filtering on WAG320N, my other wireless laptop get disconnected. And when you try to connect, it doesn't connect again.
View 3 Replies
View Related
Jun 8, 2013
We have 2 nexus 7010 switches configured with HSRP in the network. For all the vlans core1 is Master and Core2 is standby. In the current setup we have external dhcp server and dhcp relay is configured for all the vlans on Master and standby switch. The setup is running the IOS 5.2
Activity Done: During the Maintainacne activity, we isolated core1 switch in the network by disabling the vpc/keepalive and all the uplinks from access switch. The core2 switch was master for all the vlans.
Issue observed: It has been observed that new users were not getting ip address from the dhcp server. The ethereal capture showed that dhcp server was not getting the dhcp requests from the core2 switch. We disabled the dhcp feature in core2 and enabled again with dhcp relay again configured on vlan interfaces .even after doing this no change was observed in behaviour. Finally we got core1 back in network by enabling all the links.
Observation: The moment VPC link came up between the core switches, users started getting ip's from dhcp. Then we started enabling all the uplinks on core1.Core1 again become master for all the vlans and users continued getting ip’s. Network running fine.
Further Testing
1. For one of the vlan, core 2 switch has been made primary and for new users checked the dhcp functionality and it was working fine. The aim was to identify if anything wrong on core 2 related to dhcp relay
2.Again we changed the priority for this vlan and made core1 master for the same. This time we disabled this vlan on core1 and tried new user with core 2 became master and dhcp functionality worked fine for new user. Actually in this case we have simulated the same behaviour when we observed the issue with only difference of VPC was not available during the issue time as core 1 was isolated form network
Inputs needed.
Is there any known behaviour for dhcp functionality when VPC is unavailable? If we see the test scenario2 (wherein core1 was master for the vlan and we disable this vlan on core 1 and core 2 was able to relay dhcp requests for new users in this vlan.) it was actually same as scenario we observed during issue time..
View 7 Replies
View Related
Nov 20, 2012
how to disable radio on the AP 1140 from NCS script .
View 5 Replies
View Related
Jan 28, 2009
I tried to find the radiation pattern for the 1140 AP, but no luck so far. Where to find it?
View 7 Replies
View Related
Apr 18, 2012
I need a legible radiation pattern graph for the 1140 AP -- the antenna pattern. This is for a wireless deployment application which models signal strength. It needs to be specific for the 1140 AP as the antenna has a Maximum gain of 3 dBi which is different than the antenna gain on the 1130 AP.
View 2 Replies
View Related
Jan 10, 2011
I currently have a sagem router provided by my isp (sky), as the signal does not reach all areas of my premesis and sky refuse to let me use my own router I decided to purchase a wireless extender. I got a Edimax EW-7416APn and configured it using the following settings at the following address:when I connect to the extender i can gain access to the management settings, if i perform a scan using the extender it can see the original router, if I check the security settings they hold the correct ssid, security type (wpa - tisk) and the correct passphrase.
View 1 Replies
View Related
Jan 1, 2011
Just got the DIR-655 and was wandering how to prioritize the wireless connections, that way my future mother-in-law across the street will be last. I can get the Static IP for a computer, but when I go into the router settings for QoS, I don't understand what info goes in there.
View 2 Replies
View Related
Dec 19, 2010
I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior. I'm having one issue that I can't figure out though. None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless. If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC authentication open authentication key-management wpa guest-mode mbssid guest-mode wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]
View 9 Replies
View Related
Mar 28, 2012
I try to setup a 1141 aironet AP to authenticate my user through our Ms Radius Server ( Win 2008 R2).Everything is fine with small Bussiness AP WAP4410N with the following configuration:But I can't setup successfully the aironet 1141 with the same settings and getting it works.Here is my configuration for the Aironet 1141 Vlan 1 is the ssid I want to get it work with Radius.
View 1 Replies
View Related
Dec 16, 2012
We have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies
View Related
Dec 10, 2012
If I do a speed test (bandwidthplace.com) while connected to a remote locations 1140 standalone access point, the download/upload speeds are roughly 100kbps. There are no other devices connected to the access point at the time. Wired PCs on the LAN that the access point is connected to are not having a problem.Pings from the laptop, through the access point, to our central WAN router are at <10ms.The WAN circuit (remote location to headquarters) is 5Mbps. No congestion.Circuit out from headquarters to I'net is 50Mbps. No congestion.Access point and router interfaces show no errors or collisions, etc. The configuration is the same as 28 other standalone access points in 28 different LANs on the WAN. They have no problems.
View 5 Replies
View Related
Jan 2, 2013
I have 3 Cisco AP 1140 at my customer (Service Industry) place, so they requenst us to provide Hotspot solution to them for managing the Internet connection for limiting to their Customers over the account system. Let me know how i can integrate hotspot BOX with Cisco AP.
View 3 Replies
View Related
Apr 23, 2013
I have one 5508 with Product version 6.0.199.4 and about 7 Cisco 1140 APs.We have a next problems. Go out of the connection on the clients PC, while physically a wireless connection to the workstations is not broken, but access to network resources is lost and restored after some time (up to about one minute).The logs on the controller at the same time see the following message.
View 3 Replies
View Related
