i have a 1140 AP and i have an ssid on it authenticate users from NPS server.
but now i need to conifure on it 2 ssid with different vlans each ssid authenticate from the same NPS server but with diferent groups.
Any configuration example where i have a Cisco 1140 connected with a trunk to one router and with the Cisco 1140 i broadcast one SSID per vlan, one with WPA2 and other "open".?I ask because i see that when i turn on cipher, i cant configure an SSID without encryption.
View 1 Replies View RelatedI am using a Aironet 1100 series access point (AIR-AP1142N-N-K9) with IOS version c1140-k9w7-tar.124-21a.JA1. I want to create two seperate SSID's on the access point with WEP encryption. There is no VLAN configured and i want it to be like it. Also I need to broadcast both the SSID's at the same time, so the some of my users need to login with the first SSID and the others to login through the other.
View 2 Replies View Related I have an AP Aironet 1140 that have two (2) SSID: (ZDE) and (GUEST). Guest is working fine but ZDE is not giving IP addresses to users attached in this AP. I atached the sh tech of the Ap. From the configuration cisco guide of Aironet 1140 i understand that by default, access points are configured to receive IP settings from a DHCP server on your network. But i don´t know if i have to configure the dhcp server ip addres in the Ap, similar to the ip helper address in switches
Configuring the Access Point to Provide DHCP Service. These sections describe how to configure the wireless device to act as a DHCP server:
•Setting up the DHCP Server, page 5-22
•Monitoring and Maintaining the DHCP Server Access Point, page 5-24
•Setting up the DHCP Server
By default, access points are configured to receive IP settings from a DHCP server on your network. You can also configure an access point to act as a DHCP server to assign IP settings to devices on both your wired and wireless LANs.
The 1100 series access point becomes a mini-DHCP server by default when it is configured with factory default settings and it cannot receive IP settings from a DHCP server. As a mini-DHCP server, the 1100 series access point provides up to 20 IP addresses between 10.0.0.11 and 10.0.0.30 to a PC connected to its Ethernet port and to wireless client devices configured to use no SSID, and with all security settings disabled. The mini-DHCP server feature is disabled automatically when you assign a static IP address to the 1100 series access point. Because it has a console port to simplify initial setup, the 1200 series access point does not become a DHCP server automatically.
I have Internal DHCP Server configured on the Cisco WLC 5508 and all is working fine. DHCP Range is 192.168.1.100 to 192.168.1.245. Now I created another SSID but I want clients connecting to this SSID get specific IP's or from a specific range. WLC has no option to bind a DHCP pool to a specific IP so what I did I checked the option to "Override DHCP" and added the IP of my firewall WLC is connected to and setup a DHCP Pool on that firewall as 192.168.1.89 to 192.168.1.94 (192.168.1.88/29).
Client can connect to the second SSID but can't grab and IP address, what am I missing ?
I had a SSID name conflict with one of my devices and the router. I changed the routers SSID which eliminated the conflict. I noted that after changing the SSID, the name of the FTP server did not update to the new SSID. Is this an issue? I did not see any way to manually edit the FTP name. FTP works fine as is.
View 1 Replies View RelatedWe've recently sold and implemented a wireless solution using a WLC, WCS and 1140 APs.
There is a HQ site where the WLC, WCS, DNS and DHCP reside. Active Directory and a RADIUS server are also located there. There is then a WAN link to remote sites which sometimes fails. At the remote sites you'll just have a router, switches and the APs. The intention is for the APs to work in lightweight mode, falling back to H-REAP when the WAN link fails.
That works fine, but what doesn't work fine is the APs rejoining once the WAN link is restored.
They just don't. Even days later, the APs are still all disassociated from the controller despite the WAN link being up. I've 'hardcoded' the controller IP into the AP configuration, while the APs initally get the IP for the WLC from DHCP using Option 43. Despite the APs therefore knowing where WLC is, once they're disassociated from it (WAN link failed) they will not reassociate by themselves. Restarting the APs is the only way to get them to rejoin.
With hundreds of APs and in excess of 30 switches, restarting all the APs each time the WAN link fails is pretty ridiculous.
I've logged a TAC case and gone through the whole rigmarole, this is an offical bug and Cisco have informed us that it's due to be fixed sometime early 2011, but besides that there is nothing useful. So to be perfectly clear, Cisco have sold and shipped a product that doesn't work as advertised and they best they can offer us is a promise to fix it soon. I'm pretty shocked, I've never had this experience with Cisco in the past.
Ok, so now I've got to come up with a decent workaround until we get a firmware release where this is fixed. I'm looking at using CNA to automate the reloading of all the switches, I guess when an outage is reported I'll just write a procedure for the client to follow to reload all their APs.
Is it possible to assign a single ssid to multiple interface groups by assigning the ssid to multiple AP groups?
I have buildings geographically dispersed that are configured with multiple vlans in interface groups so that I can maintain an addressing scheme of dhcp assigned addresses per building. Each building is also further grouped as AP groups. I'd like to know if by assigning the same wlan ssid to each of the AP groups, will I maintain addressing integrity for each building? I'm thinking it will work.
Do the buildings have to be outside AP range of each other to avoid problems?
5508 controller
7.2.110.0 code
6 buildings
6 interface groups
1 ssid
Quick question about the association web interface tab on a 1140. I have noticed that the Device Type shows as "unknown" and the Name shows as "NONE."
View 1 Replies View RelatedI've set up a Cisco Aironet 1301 AP to be used for a guest network. I've got several other of the Aironet 1140-series around the business but none of them are in reach of this one at the moment.
The problem I have is that clients that try to connect to the AP are either not able to connect at all or lose their connection after some seconds. The config is more or less copied from the other APs with the same guest VLAN.
We've recently sold and implemented a wireless solution using a WLC, WCS and 1140 APs.
There is a HQ site where the WLC, WCS, DNS and DHCP reside. Active Directory and a RADIUS server are also located there. There is then a WAN link to remote sites which sometimes fails. At the remote sites you'll just have a router, switches and the APs. The intention is for the APs to work in lightweight mode, falling back to H-REAP when the WAN link fails.That works fine, but what doesn't work fine is the APs rejoining once the WAN link is restored.
They just don't. Even days later, the APs are still all disassociated from the controller despite the WAN link being up. I've 'hardcoded' the controller IP into the AP configuration, while the APs initally get the IP for the WLC from DHCP using Option 43. Despite the APs therefore knowing where WLC is, once they're disassociated from it (WAN link failed) they will not reassociate by themselves. Restarting the APs is the only way to get them to rejoin.
With hundreds of APs and in excess of 30 switches, restarting all the APs each time the WAN link fails is pretty ridiculous.
I've logged a TAC case and gone through the whole rigmarole, this is an offical bug and Cisco have informed us that it's due to be fixed sometime early 2011, but besides that there is nothing they can do. So to be perfectly clear, Cisco have sold and shipped a product that doesn't work as advertised and they best they can offer us is a promise to fix it soon. I'm pretty shocked, I've never had this experience with Cisco in the past.
Ok, so now I've got to come up with a decent workaround until we get a firmware release where this is fixed. I'm looking at using CNA to automate the reloading of all the switches, I guess when an outage is reported I'll just write a procedure for the client to follow to reload all their APs.
A script that can query the associated status of APs and reload them as needed, automatically, would be pretty cool. Perhaps that can be done with SNMP.
I'm configuring an 1140 and trying to make it invisable to any user that doesnt know the SSID. The SSID is not broadcast, however my clients see "Other Network" in their list of available networks. Short of turning off the AP is there any way through the 1140's configuration to prevent this "Other Network" from showing up in the clients available networks list.
View 2 Replies View Relatedhow to disable radio on the AP 1140 from NCS script .
View 5 Replies View RelatedA customer has RADIUS running on a Win Server 2008 R2 machine, has Autonomous 1140 APs and a mix of Windows 7 and XP Pro clients. Using PEAP as the authentication method the Win 7 clients can access the WLAN, but the Win XP clients cannot. The Win XP clients are at least SP2. I am doing some research before going to site on Friday and wanted to poll the community. I found an older post speaking to a MS Hotfix under KB#885453, but it referes to "third-party RADIUS servers," not MS servers URL.
View 14 Replies View RelatedI tried to find the radiation pattern for the 1140 AP, but no luck so far. Where to find it?
View 7 Replies View RelatedI'm using 3 AP's 1140 with local authentication using local radius (flex connect mode).the radius server im using is MS 2008 R2.authentication is working great on all devices pc's&mobile.authentication method is PEAP wpa2 aes enterprise.after 3 or 4 hours devices loose connectivity to the web.the device seems to be still connected to the ap but there is no ping to host from local lan or any arp learnd on local router.only manual disconnect on device and reconnecting brings connectivity up again.in one case only reseting the AP's worked.
View 6 Replies View RelatedI need a legible radiation pattern graph for the 1140 AP -- the antenna pattern. This is for a wireless deployment application which models signal strength. It needs to be specific for the 1140 AP as the antenna has a Maximum gain of 3 dBi which is different than the antenna gain on the 1130 AP.
View 2 Replies View RelatedIn our project we are building a smartphone application dat determines the locations of persons in a building, using Wifi access points.Using 3 accespoint we are calculating the overlap of 3 circles.Today we measured the signal strength and found out that it changes around alot.So we dont really know if our measurements are right.
We would like to know what the RSSI strengths are of the following access point per meter.Cisco Aironet 1140 2.4 ghz
I just installed an Aironet 1140 to replace a Netgear ProSafe access point that I had in my network prior. I'm having one issue that I can't figure out though. None of the client PCs can establish a connection to an external (over the internet) VPN server while on the Aironet wireless. If i unplug the AP and plug a PC into the same port that normall feeds the Aironet I can VPN just fine.
Is there any "VPN Passthrough" option that needs to be enabled somewhere on the 1140 that is blocking this traffic for some reason?
i'm running the following IOS BOOTLDR: C1140 Boot Loader (C1140-BOOT-M) Version 12.4(18a)JA3, RELEASE SOFTWARE (fc1) and I've included my running config below
Current configuration : 2092 bytes!version 12.4no service padservice timestamps debug datetime msecservice timestamps log datetime msecservice password-encryption!hostname ap!enable secret 5 [omitted]!no aaa new-model!!dot11 syslog!dot11 ssid MetroC authentication open authentication key-management wpa guest-mode mbssid guest-mode wpa-psk ascii 7 [omitted]!!!username Cisco password 7 [omitted]!!bridge irb!!interface Dot11Radio0 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 speed basic-1.0 basic-2.0 basic-5.5 basic-11.0 basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface Dot11Radio1 no ip address no ip route-cache ! encryption mode ciphers aes-ccm ! ssid MetroC ! antenna gain 0 no dfs band block speed basic-6.0 basic-9.0 basic-12.0 basic-18.0 basic-24.0 basic-36.0 basic-48.0 basic-54.0 m0. m1. m2. m3. m4. m5. m6. m7. m8. m9. m10. m11. m12. m13. m14. m15. channel width 40-above channel dfs station-role root bridge-group 1 bridge-group 1 subscriber-loop-control bridge-group 1 port-protected bridge-group 1 block-unknown-source no bridge-group 1 source-learning no bridge-group 1 unicast-flooding bridge-group 1 spanning-disabled!interface GigabitEthernet0 no ip address no ip route-cache duplex auto speed auto no keepalive bridge-group 1 no bridge-group 1 source-learning bridge-group 1 spanning-disabled!interface BVI1 ip address 192.168.1.3 255.255.255.0 no ip route-cache!ip http serverno ip http secure-serverip http help-path [URL]
I try to setup a 1141 aironet AP to authenticate my user through our Ms Radius Server ( Win 2008 R2).Everything is fine with small Bussiness AP WAP4410N with the following configuration:But I can't setup successfully the aironet 1141 with the same settings and getting it works.Here is my configuration for the Aironet 1141 Vlan 1 is the ssid I want to get it work with Radius.
View 1 Replies View RelatedWe have 6 aironet 1140's throughout the office I have them all configed as one ssid but I would like the DHCP to come from our Windows server. Right now I have set them up with ip dhcp pools. So what is the secret to get them to send dhcp requests to the Windows server?
View 3 Replies View RelatedIf I do a speed test (bandwidthplace.com) while connected to a remote locations 1140 standalone access point, the download/upload speeds are roughly 100kbps. There are no other devices connected to the access point at the time. Wired PCs on the LAN that the access point is connected to are not having a problem.Pings from the laptop, through the access point, to our central WAN router are at <10ms.The WAN circuit (remote location to headquarters) is 5Mbps. No congestion.Circuit out from headquarters to I'net is 50Mbps. No congestion.Access point and router interfaces show no errors or collisions, etc. The configuration is the same as 28 other standalone access points in 28 different LANs on the WAN. They have no problems.
View 5 Replies View RelatedI have a Cisco Aironet 1140 with ENABLED broadcasting SSID, encryption is WPA2(personal). Ubuntu 12.04 and Windows 7 are authenticated, but MACBooks never be authenticated. Any specific configuration for MAC books?
View 6 Replies View RelatedI have 3 Cisco AP 1140 at my customer (Service Industry) place, so they requenst us to provide Hotspot solution to them for managing the Internet connection for limiting to their Customers over the account system. Let me know how i can integrate hotspot BOX with Cisco AP.
View 3 Replies View RelatedI have one 5508 with Product version 6.0.199.4 and about 7 Cisco 1140 APs.We have a next problems. Go out of the connection on the clients PC, while physically a wireless connection to the workstations is not broken, but access to network resources is lost and restored after some time (up to about one minute).The logs on the controller at the same time see the following message.
View 3 Replies View RelatedWe have bought autonomous APs AIR-AP1141N-E-K9 and converted them to the lightweight mode, but they cannot join the WLC 5508. The errors are below. There were NO problems with the LAPs that were bought before, together with the
WLC.AP's IP: 172.22.90.27 IOS version 12.4
WLC's IP: 172.22.90.20 IOS version 6.0.188.0
logs from the AP:
Translating "CISCO-LWAPP-CONTROLLER"...domain server (255.255.255.255)
*Oct 13 21:37:06.044: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.045: %CAPWAP-5-CHANGED: CAPWAP changed state to DISCOVERY
*Oct 13 21:37:06.046: bsnInitRcbSlot: slot 1 has NO radio
[Code] .....
The time is set to the WLC with the NTP. Don't lookup at the time the logs were made - they were made not during the same day/time
when I try to configure my autonomous 1140, it does not work unless I use numbers.If I put in my phone number as my key, I can authenticate just fine. When I change it to some random letters and numbers.
View 6 Replies View RelatedI have an Aironet 1140 AP that will not connect to the network when on PoE (either using a Cisco PoE injector) or a Avocent Switch that provides PoE.
The AP will boot up and and devices will connect to it (the LED changes to blue) but none of the devices can get access to the corporate network or internet. When the AP is powered by the standard power supply, it operates normally, i.e. devices can access the network. Are there settings that can be changed to get the AP to work correctly on PoE?
I am trying to chang IP configuraton for my Cisco 1140 AP, but in CLI I dont have a "config" command (i used en before to enable administrative mode)
Bellow are the commands I can see:
AP7081.0506.d54a#?
Exec commands:
cd Change current directory
[Code].....
I have recently setup one stand alone aironet 1140 with mostly default settings with WPA key. but, it seems sometimes it's dropping the connections. hardly 15 users are connecting to aironet at the moment.
View 2 Replies View RelatedWe have been successfully using our Aironet 1140 AP in standalone mode with mainly Windows pcs & laptop users, and now, iPads and iPhones. All seem to connect happily through the 1140.
Recently we have a requirent to be able to use Apple's Airplay. Basically, it is not working through the 1140, it works ok via wired ethernet. Can the 1140 support Airplay? - If yes, what precisely must be enabled/configured?
We have a single Class C network without any Vlans. I understand multicast must be enabled, I can't see where to enable this. How to get this working if it is at all possible.
I am involved in a project that wants to implement location based services using the WLAN to track users has they move around the estate. I have been conducting a survey using ESS and Air Magnet and both have difficulty in placing APs when the ceiling height goes above 4.0m I am using cisco 1140n APs to get signal readings, but does location tracking start to breakdown once the AP is at a significant height of 4-6m
View 2 Replies View RelatedJust a few days ago, one of my coworkers computer was unable to see any of our wireless access points - all aironet 1140. He is one of two using a Win 7 machine, everybody else uses Mac with either Lion or Mountain Lion. The Macs can "see" and connect to our wireless AP's just fine.
The odd thing is that is his computer can pick up our neighbors wireless access points, but can't "see" ours. Also, a few peoples phones can no longer detect them either - both iphone 4's (ios 5.1.1 and 6) and androids (2.3 and 4)
No changes were made to our AP's, then people started having wifi issues.